首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
In the current investigation, raw biogas obtained from rural sectors was used as the alternative to gasoline fuel in the spark ignition (SI) engine. The performance and efficiency are mainly dependent on the combustion phasing for which “ignition timing” is an effective tool in a SI engine. Hence, the objective of the present work is to understand the effect of “variable ignition timing” for a biogas-fueled SI engine. For this purpose, a single cylinder, 4-stroke, SI engine of rated power 4.5 kW was operated with raw biogas at a compression ratio (CR) of 10. By maintaining a speed of 1650 rpm, the engine was operated in wide open (WOT) and part throttle (PT) mode with an equivalence ratio of 0.81 and 0.83, respectively. It was observed that the biogas fueled SI engine was found to be operative only within the ignition advance (IA) range of 33–47° CA bTDC both in WOT and PT conditions. The results showed optimal brake power (BP), brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) are achieved at 45° CA bTDC. The average peak cylinder pressure, neat heat release rate (NHRR) and mean gas temperature (MGT) are also observed to be maximum while CO and HC emission at this point of IA were found to be minimum. Due to controlled and complete combustion, CO2 and NOx concentration in the exhaust emission were found to be higher at this point of ignition timing.  相似文献   

2.
Experiments were performed in a single cylinder common-rail diesel engine that adopts a low temperature premixed charge compression ignition (PCCI) mode. Combustion features of dimethyl carbonate (DMC)-diesel blends under various centers of heat release (COHRs) were revealed in details. With retarding of COHR, all the peaks of pressure and pressure rise rate and bulk gas temperature are postponed and declined in sequence. Normally, the crank angle of peak pressure is quite close to the COHR, while the peak of bulk gas temperature appears about 7°CA after COHR as a rule. The prolongation can be demonstrated at every stage of combustion such as q10 and q90 with the COHR being put backward. In addition, the heat release of diesel is completely slower than that of D10 fuel at various stages. Unfortunately, retarding of COHR implies a declining thermal efficiency of engines as well as a higher cyclic variation in general. Nevertheless, D10 blend has higher thermal efficiency than diesel thanks to high oxygen content of DMC and low boiling point that prompts better fuel atomization and complete combustion. Meanwhile, the cyclical variation of D10 is greater than diesel fuel owing to the low heat value, high latent heat of vaporization, and poor flammability of DMC. As a total, a comprehensive understanding of PCCI combustion features under different COHRs can be conducive to conducting effective management of combustion process and manipulating the subsequent emission performance to a favorable level.  相似文献   

3.
Recent strategies for simultaneously reducing NOx and soot emissions have focused on achieving nearly premixed, low-temperature combustion (LTC) in diesel engines. A promising approach in this regard is to vary fuel reactivity in order to control the ignition delay and optimize the level of premixing and reduce emissions. The present study examines such a strategy by performing 3-D simulations in a single-cylinder of a diesel engine. Simulations employ the state-of-the-art two-phase models and a validated semi-detailed reaction mechanism. The fuel reactivity is varied by using a blend of n-heptane and iso-octane, which represent surrogates for gasoline and diesel fuels, respectively. Results indicate that the fuel reactivity strongly influences ignition delay and combustion phasing, whereas the start of injection (SOI) affects combustion phasing. As fuel reactivity is reduced, the ignition delay is increased and the combustion phasing is retarded. The longer ignition delay provides additional time for mixing, and reduces equivalence ratio stratification. Consequently, the premixed combustion is enhanced relative to diffusion combustion, and thus the soot emission is reduced. NOx emission is also reduced due to reduced diffusion combustion and lower peak temperatures caused by delayed combustion phasing. An operability range is observed in terms of fuel reactivity and SOI, beyond which the mixture may not be sufficiently well mixed, or compression ignited. The study demonstrates the possibility of finding an optimum range of fuel reactivity, SOI, and EGR for significantly reducing engine out emissions for a given load and speed.  相似文献   

4.
The increasing consumption and excessive extraction of conventional fuels is the matter of serious concern. Nowadays, world is looking for alternative sources of fuel which can partially replace conventional fuel dependence. The current investigation intends to provide evaluation of bio-ethanol preparation from Water Hyacinth (WH) and its influence on diesel engine performance under various operating conditions. This study explores the extraction of glucose from WH (Eichhornia crassipes) pretreated with sulfuric acid (H2SO4) for production of bio-ethanol. For the production of bio-ethanol different concentrations of H2SO4 acid hydrolysate (1%, 2%, 4%, 6%, 8%, and 10%) were prepared which was then followed by fermentation with cellulose fermenting yeasts. From results, it was observed that 4% H2SO4 acid hydrolysis produces higher concentrations of ethanol than other concentrations. Bio-ethanol extracted from WH was blended with diesel in different proportions (5%, 10%, 15%, 20%, and 25%) v/v and performance and emissions were experimentally investigated on single cylinder diesel engine under various load conditions. Experimental results show that 5 BED [5% bio-ethanol (WH + 95%diesel v/v) and 10BED (10% bio-ethanol (WH + 90%diesel v/v)] produces higher brake power, brake thermal efficiency and brake mean effective pressure with improved exhaust emission profiles than any other blend.  相似文献   

5.
Internal combustion engines running on gaseous fuels produce low torque because the inducted gaseous fuel displaces air and reduces the volumetric efficiency. This can be overcome by injecting the gaseous fuel directly into the cylinder after the intake of air is completed. This work is a step in developing and demonstrating a cost effective system, as such systems are not readily available for small applications. A low-pressure gas injector was mounted on the cylinder barrel of a fully instrumented dual fuel engine. Its location is such that the injector will be exposed to the cylinder gases about 65.5 degrees before bottom dead center, where the cylinder pressure and temperature will be relatively low. An electronic controller was also developed to time the injection process to occur after the intake valve closes and also to control the duration of injection (quantity). Experiments were conducted with LPG (Liquefied petroleum gas) as the primary fuel that was injected with this new system and diesel as the pilot fuel at the rated speed of 1500 rpm with different amounts of LPG at 80% and 100% load. Comparisons of performance, combustion and emissions with the conventional manifold injection of LPG were done. The system allowed greater amounts of LPG to be used without knock as compared to manifold injection. On the whole the developed system has potential for application in small dual fuel and spark ignited gas engines and can be taken up for further optimization.  相似文献   

6.
The overall objective of this study was to explore the utility of waste plastics as a potential source of diesel fuel. An experimental study was conducted to evaluate the use of various blends of plastic oil produced from waste polyethylene (WPE) with diesel fuel (D). WPE was degraded thermally and catalytically using sodium aluminum silicate as a catalyst. The oil collected at optimum conditions (414°C–480°C range and 1 h reaction time) was fractionated at different temperatures and fuel properties of the fractions were measured. Plastic oil was blended with diesel fuel at the volumetric ratios of 5%, 10%, 15%, 20%, and 100%. Fuel properties of blends are found comparable with those of diesel fuel within the EN 590 Diesel Fuel standard and they can also be used as fuel in compression ignition engines without any modification. Engine performance and exhaust emission studies of 5% WPE-D (WPE5) blend were performed. Experimental results showed that carbon monoxide (CO) emission is decreased by 20.63%, carbon dioxide (CO2) emission is increased by 3.34%, and oxides of nitrogen (NOx) emission is increased by 9.17% with WPE-D (WPE5) blend compared to diesel fuel.  相似文献   

7.
In the recent decades, the energy demand for transport and industrial sector has increased considerably. Fossil fuels which were the major fuel source for decades are no more sustainable. Biodiesel is an efficient alternative compared to depleting fossil fuels. The prospect of biodiesel as the best alternative fuel is a reliable source compared to depleting fossil fuels. Hydrogen is also considered as an attractive alternative fuel producing low emission with improved engine performance. This paper investigates the performance and emission characteristics of a single cylinder compression ignition engine using hydrogen as an inducted fuel and biodiesel, aka Pongamia pinnata as injected fuel. The experiments are conducted for different quantities of hydrogen induction through the intake manifold in order to improve the performance of the engine. The performance parameters such as brake thermal efficiency, brake specific fuel consumption, exhaust temperature and emission quantities like HC, NOX, CO, CO2 of biodiesel fueled CI engine with variable mass flow rate of hydrogen are investigated. The performances of biodiesel combined with hydrogen at varying mass flow rates are also compared. The 10 LPM hydrogen induction with biodiesel provided 0.33% increase of brake thermal efficiency compared with diesel and increase of 3.24% to biodiesel at 80% loading conditions. The emission of HC decreased by 13 ppm, CO decreased by 0.02% by volume and CO2 decreased by 3.8% by volume for biodiesel with induction of hydrogen at 10 LPM to that of neat biodiesel for 80% load conditions.  相似文献   

8.
This work aimed to prove the effects of adding different proportions of ethanol with diesel (DE) and ethanol–water mixture with diesel (DEW) in a single-cylinder diesel engine on the performance, emissions, and combustion parameters. The blends were stabilized by tetra methyl ammonium bromide (TMAB) as the additive. The study was conducted at two operating conditions initially on a normal diesel engine and in the second case the engine piston, valves, and cylinder head coated with zirconia (ZrO2) alumina (Al2O3). The results showed that the addition of 10% ethanol with diesel performed almost equivalent to neat diesel with 29.2% BTE and a 17.7% decrease in smoke and an 11.4% increase in NOx emission at peak load compared to that of the base fuel. Modified engines with thermal barrier coating (TBC) performed superior to normal engines with 4% and 5.5% increase in BTE, respectively, for DE- and DEW-type fuels with reduced exhaust emissions. A 5% addition of water with diesel–ethanol blends favors a higher proportion of ethanol to be employed in diesel engines.  相似文献   

9.
The combustion of hydrocarbon (HC) fuels in internal combustion (IC) engines is modified by the presence of a few parts per million of megadalton molecular weight elastomers. The viscoelasticity imparted provides: reduced fuel vaporization, lesser back pressure, larger average droplet sizes, and lower combustion chamber temperatures. These effects result in: a reduction of emissions of HC, CO and NOx of more than 70%, a substantial decrease in the number of particulates from diesel engines, a drop in combustion temperatures of more than 30vv°C, increases in engine power of more than 10%, an improved fuel octane rating, and economies of fuel consumption of more than 20%. The results are magnified during transitions, especially in the lower gears, used more often in urban traffic, where normal fuels emit more pollutants. These effects have a positive public health impact due to reductions in ozone, acid rain, particulates and partially oxidized HC.  相似文献   

10.
An attempt has been made to produce stable water–diesel emulsion with optimal formulation and process parameters and to evaluate the performance and emission characteristics of diesel engine using this stable water–diesel emulsion. A total of 54 samples were prepared with varying water/diesel ratio, surfactant amount and stirring speed and water separation was recorded after 24 and 48 hr of emulsification. The recorded data were used in artificial neural network (ANN)-particle swarm optimization (PSO) technique to find the optimal parameters to produce water–diesel emulsion for engine testing. The predicted optimal parameters were found as 20% water to diesel ratio, 0.9% surfactant and 2200 rpm of stirrer for a water separation of 14.33% in one day with a variation of 6.54% against the actual value of water separation. Water–diesel emulsion fuel exhibited similar fuel properties as base fuel. The peak cylinder gas pressure, peak pressure rise rate and peak heat release rate for water–diesel were found higher as compared to diesel at medium to full engine loads. The improved air-fuel mixing in water–diesel emulsion enhanced brake thermal efficiency (BTE) of engine. The absorption of heat by water droplets present in water–diesel emulsion led to reduced exhaust gas temperature (EGT). With water–diesel emulsion fuel, the mean carbon monoxide (CO), unburned hydrocarbon and oxides of nitrogen (NOx) emissions reduced by 8.80, 39.60, and 26.11%, respectively as compared to diesel.  相似文献   

11.
ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in pmax. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the pmax. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NOx level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.  相似文献   

12.
In this study, several bio-source-fuels like fresh and waste vegetable oil and waste animal fat were tested at different injector pressures (120, 140, 190, 210 bar) in a direct-injection, naturally aspirated, single-cylinder diesel engine with a design injection pressure of 190 bar. Using 2k factorial analysis, the effect of injection pressure (Pi) and fuel type on three engine parameters, namely, combustion efficiency (etac), mass fuel consumption (mf), and engine speed (N) was examined. It was found that Pi and fuel type significantly affected both etac and mf while they had a slight effect on engine speed. Moreover, with diesel and biodiesels, the etac increased to a maximum at 190 bar but declined at the higher Pi value. In contrast, higher Pi had a favorable effect on etac over the whole Pi range with all the other more viscous fuels tested. In addition, the mass fuel consumption consistently decreased with an increase in Pi for all the fuels including the baseline diesel fuel, with which the engine consistently attained higher etac and higher rpm compared to all the other fuels tested.  相似文献   

13.
In this study, the rice bran oil (RBO) has been converted into methyl ester with an aid of transesterification reaction. Chemically, transesterification means conversion of triglyceride molecule or a complex fatty acid into alcohol and ester by removing the glycerin and neutralizing the free fatty acids. The B20 blend samples [80% diesel + 20% biodiesel] were prepared for each methyl ester obtained from RBO and then the cerium oxide (CeO2) nanoparticles were added to the each B20 blend samples at a dosage of 50 ppm and 100 ppm with an aid of ultrasonicator. Moreover, in the absence of any engine modifications, the performance and emission characteristics of those blend samples have been investigated from the experimentally measured values such as density, viscosity, cloud point, pour point, and calorific value while the engine performance was also analyzed through the parameters like exhaust gas temperature (EGT), brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), exhaust emission of carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx). The experimental results reveal that the use of CeO2 blended biodiesel in diesel engine has exhibited good improvement in performance characteristic and reduction in exhaust emissions.  相似文献   

14.
Biofuel blends produced from Jatropha (Jatropha curcas) and Karanja (Pongamia pinnata) oil were evaluated for their combustion properties. Two kinds of blends (regular diesel with Jatropha and Karanja oil) were prepared at 20% volume to the diesel and tested as alternative fuels in single cylinder (vertical), water-cooled, direct injection diesel engine at the rated speed of 1500 rpm. The performance of the engine in terms of thermal efficiency at full load for diesel was 30%. For Jatropha and Karanja biodiesel blends, the thermal efficiencies were 29.0% and 28.6%, respectively. The maximum cylinder pressure and ignition delay for biodiesel fuel blends are very close to that of regular diesel. Prolonged combustion was observed for Karanja oil blend in comparison to Jatropha oil blend. The combustion pattern also reveals the slow burning characteristics of vegetable oils and this study indicates that the blended biofuels have combustion characteristics that are similar to regular diesel fuels.  相似文献   

15.
EGR is one of the most significant strategies for reducing especially nitrogen oxides (NOx) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NOx emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NOx emissions.  相似文献   

16.
In this paper, the performance of direct injection diesel engine was experimentally investigated under the influence of two different pistons’s geometry deep bowl combustion chamber (DBCC) and toroidal combustion chamber (TCC) compared with standard piston combustion chamber (SPCC) geometry. The experiments were carried out standard atmospheric conditions of 1.01325 bar and 30 ± 2 °C. The piston bowl was designed and developed without modifying the compression ratio of the engine. The investigations were carried out with B25 (25% GOME + 75% diesel), B50 (50% GOME + 50% diesel), B75 (75% GOME +25% diesel) and B100 (100% GOME) by volume blends for three different bowl geometries. The thermogravimetric analysis (TGA) was given the importance of higher in-cylinder temperature for the mass change of GOME leads to a more premixed phase of combustion. The results showed that DBCC has better combustion characteristics when compared with SPCC and TCC for all the blends. The B25 and B50 blends showed good combustion characteristics with DBCC and SPCC individually. While TCC showed average engine characteristics for all the blends categorically, the brake thermal efficiency for B25 blend confirmed a 4.7% higher than SPCC-diesel with DBCC piston, and the smoke, CO (Carbon monoxide), and HC (Hydrocarbon) are reduced by 9.2%, 30.7%, and 4.6%, respectively. Thus, the B25 blend in a DBCC piston engine was observed to be the distinction than other configurations. The results confirmed that the DBCC is a good option for B25 blend.  相似文献   

17.
In this study, the top surfaces of piston and valves of a four-strokes and direct-injection diesel engine have been coated—with no change in the compression ratio—with a 100 μm of NiCrAl lining layer via plasma spray method and this layer has later been coated with main coating material with a mixture of 88% of ZrO2, 4% of MgO and 8% of Al2O3 (400 μm). Then, after the engine-coating process, ultra-low sulfur diesel (ULSD) as base fuels and its blend with used frying cottonseed oil derived biodiesel in proportion of 20%, volumetrically, have been tested in the coated engine and data of combustion and performance characteristics on full load and at different speeds have been noted. The results, which were compared with those obtained by uncoated-engine operation, showed that thermal efficiency increased, and engine noise reduced. Cylinder gas pressure values obtained from the diesel engine which has been coated with thermal barriers have been found to be somewhat higher than those of the uncoated-engine. Also, maximum pressure values measured in both engines and under the same experimental conditions through the use of test fuel have been obtained after TDC. Moreover, heat release rate and heat release have occurred earlier in the coated-engine. NOx emissions were increased while CO and HC emissions were remained almost the same with a little bit decrease.  相似文献   

18.
As a potential hydrocarbon production method, the hydrocracking of soybean biodiesel, using a commercial petroleum hydrocracking catalyst, was studied. Experiments were carried out in a 1,000 mL, high-pressure autoclave for 2–4 hr over the temperature range of 200–280°C under an initial hydrogen pressure of 10 MPa. Hydrocracking of soybean biodiesel produced n-paraffins in the C8–C17 boiling range, which includes both green gasoline and diesel. Both pressure and temperature play important roles in the transformation of soybean biodiesel. Hydrocarbons can be formed above 220°C with a liquid yield of 81.76%. The n-alkanes content of the liquid product reached 32.29% at 280°C, with 88.32% C11–C14 selectivity. In addition, hydrocracking results in many changes of catalyst such as physical properties, morphology, etc. For the used catalyst, the concentrations of Ni and C increased, and the pore channels were significantly reduced.  相似文献   

19.
This research work investigates the engine performances, combustion characteristics, and emission of exhaust gases of variable compression ratio engine fuelled with cottonseed oil methyl ester (COME) and diesel at different blends. The analysis showed that heat release rate and cylinder pressure is higher for diesel than COME blends. Higher BTE is obtained at the maximum load condition. The higher BTE and lower SFC are obtained for blend B15 as 42.17% and 0.2 kg/kW-hr at brake mean effective pressure (BMEP) of 4.64 bar. Also it is found that the peak cylinder gas pressure and combustion duration increases when the BMEP increases. At the BMEP of 3.51 bar, higher HRR is observed as 18.12 J/deg. Increase in HRR is obtained as 6.07% for B30 at BMEP of 4.64 bar when compared to diesel. Ignition delay decreased by 13.16% for B100, by the increment of blend proportions when compared to diesel, at BMEP of 4.64 bar. Lower smoke, HC and CO emissions are observed when increasing the blend proportions, whereas the nitric oxide emissions increases due to the better combustion resulted in higher temperatures. At BMEP of 4.64 bar, the CO emissions are reduced to 25.24% for neat biodiesel when compared with the diesel.  相似文献   

20.
A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NOX emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号