钙基吸收剂循环煅烧/碳酸化法捕集CO2的发展

煅烧过程中吸收剂的烧结现象和循环反应过程中的磨损及破碎现象是导致钙基吸收剂循环煅烧/碳酸化捕集CO2性能不稳定的主要原因.针对目前几种常用的提高钙基吸收剂循环捕集性能的方法进行了总结,并对钙基吸收剂顺序脱除SO2/CO2的方法进行解释.     

相变溶剂捕集CO2技术的研究进展

化学溶剂吸收法是目前应用最广泛的燃烧后CO₂捕集技术。介绍了化学溶剂吸收法的基本原理,综述了化学溶剂吸收法的研究现状,比较分析了几种常用CO₂吸收剂的优缺点。重点阐述了两类新型相变吸收剂（液-液相变溶剂和液-固相变溶剂）的研究进展。指出：新型相变溶剂是理想的CO₂吸收剂,用其捕集CO₂可有效降低吸收剂的再生能耗;相变溶剂吸收CO₂的传质反应动力学以及不同类型相变溶剂的挥发和降解特性应作为今后该领域的研究重点。     

火电厂CO2捕集与封存技术探讨

火电厂CO2减排技术主要包括燃烧前处理、燃烧中减排及燃烧后捕集三类。介绍了IGCC、富氧燃烧、胺吸收法、生物法等CO2捕集与封存技术,分析其存在问题及应用前景。     

木醋调质石灰石直接硫化反应特性研究

针对O2/CO2燃烧技术适于采用炉内喷钙脱硫方式脱硫而钙利用率仍有较大提升空间的问题,采用木醋废液调质改性石灰石,并利用热分析方法对木醋调质石灰石在O2/CO2气氛下的直接硫化反应特性进行了试验研究。试验结果表明石灰石经木醋调质后直接硫化反应性能显著提高,反应温度、吸收剂粒径以及反应气氛中SO2和O2的浓度都对直接硫化反应存在影响,分析认为调质对石灰石热解固体产物微观结构的改善是脱硫性能得以显著提升的主因。     

烯胺活化羟乙基乙二胺吸收CO2的反应热

以羟乙基乙二胺（AEEA）为基础吸收剂,分别加入二乙烯三胺（DETA）、三乙烯四胺（TETA）、四乙烯五胺（TEPA）作为活化剂,探讨了不同烯胺体积分数和CO2负载量（吸收的CO2与活化吸收剂的摩尔比）对各烯胺活化的AEEA吸收剂CO2吸收热、解吸热、CO2脱除率的影响。综合对比结果,最优的活化吸收剂为AEEA+5%（φ）DETA,其最低CO2吸收热为63.0 kJ/mol（以每摩尔CO2计）,解吸热为82.5 kJ/mol,CO2脱除率为76.2%。     

半干法脱除球团烟气中的SO2及Hg0

采用钙基吸收剂及复合氧化剂半干法脱除模拟球团烟气中的SO_2及Hg~0,考察了多因素条件对吸收效果的影响。实验结果表明,在以NaClO和NaClO_2为复合氧化剂、 NaClO与NaClO_2体积比1∶0.5、复合氧化剂质量分数3%、反应温度110℃、钙基吸收剂质量3.0 g、模拟烟气进气流量1.2 L/min的条件下,SO_2和Hg~0的脱除率分别为98%和93%,证明钙基吸收剂与复合氧化剂对污染物球团烟气中的SO_2和Hg~0有良好的脱除作用。     

改性多孔淀粉对Cu2+的捕集性能

以玉米淀粉为原料,采用糖化酶和α-淀粉酶复合酶解制成多孔淀粉,多孔淀粉经交联、间接醚化、胺化、黄原酸酯化反应得到二硫代氨基甲酸基改性多孔淀粉(DTCPS)重金属捕集剂.研究了DTCPS对Cu2+的捕集性能.实验结果表明:制得的多孔淀粉的比表面积为1.264 5 m2/g,比玉米淀粉的比表面积增大了138.5%;制得的多孔淀粉是一种中孔淀粉;Cu2+溶液pH为1-5时,DTCPS的Cu2+饱和捕集量均较高;Cu2+初始质量浓度为0～70 mg/L时,DTCPS对Cu2+的捕集性能很好,溶液中Cu2+的剩余质量浓度低于0.12 mg/L,Cu2+的去除率达99%以上.DTCPS对Cu2+的捕集性能明显优于二硫代氨基甲酸基改性淀粉(DTCS).     

我国电力行业CO2减排技术及应用前景分析

阐述了我国燃煤电厂CO2排放现状及趋势,将CO2减排技术分为捕集与封存两个部分进行讨论,介绍了目前主要的CO2捕集与封存技术及其研究进展,并分析了各种技术的特点及其在我国电力行业的应用前景。指出电厂位置、CO2捕集方案及封存方式三者之间是相互影响、相互制约的,其中CO2去向是关键因素,处于不同地理位置的电厂需根据具体情况选择相适应的CO2捕集与封存技术的组合。探讨了各种捕集与封存技术的应用前景,建议由国家相关部门或行业支持,建设国家或行业层面的工业化试验中心或试验台。     

氨盐法捕集CO2

Chemical Engineering,2013,120(7):11氨是一种很有前途的烟气中CO2的捕集剂,因为每个氨分子可吸收1分子的CO2,而有机胺吸收剂则需2分子才能吸收1分子的CO2。然而,由于氨具有挥发性,必须将烟气冷却到大约10℃,这需要大量的电能,而且,在如此低的温度下,氨的吸收率不够高。美国斯坦福国际研究所(SRI International)的     

MAP-DMSO-PMDETA三元相变吸收剂的CO2捕集性能

以仲胺3-甲基胺基-1-丙醇(MAP)为主吸收剂、二甲基亚砜(DMSO)为有机稀释剂、五甲基二乙烯三胺(PMDETA)为辅助吸收剂,制备了新型MAP-DMSO-PMDETA三元相变吸收剂,考察了其相变行为和CO₂吸收性能。实验结果表明：在MAP、DMSO与PMDETA的质量比为3∶6∶11,吸收温度为40℃,CO₂体积分数为10%,进气流量为1.25 L/min的优化条件下,吸收饱和后发生液液分相,吸收剂负载量为0.79 mol/kg,吸收负荷为0.47 mol/mol(以MAP计),富相的体积分数为45.1%,并富集了95.1%的CO₂,而黏度仅为11.83 mPa·s;该三元相变吸收剂不仅解吸性能优异,同时循环稳定性良好,经5次吸收-解吸循环,解吸负荷稳定在0.34 mol/mol(以MAP计)左右,解吸效率可达69.4%。     

Sorbents for CO2 capture from high carbon fly ashes

Fly ashes with high-unburned-carbon content, referred to as fly ash carbons, are an increasing problem for the utility industry, since they cannot be marketed as a cement extender and, therefore, have to be disposed. Previous work has explored the potential development of amine-enriched fly ash carbons for CO(2) capture. However, their performance was lower than that of commercially available sorbents, probably because the samples investigated were not activated prior to impregnation and, therefore, had a very low surface area. Accordingly, the work described here focuses on the development of activated fly ash derived sorbents for CO(2) capture. The samples were steam activated at 850 degrees C, resulting in a significant increase of the surface area (1075m(2)/g). The activated samples were impregnated with different amine compounds, and the resultant samples were tested for CO(2) capture at different temperatures. The CO(2) adsorption of the parent and activated samples is typical of a physical adsorption process. The impregnation process results in a decrease of the surface areas, indicating a blocking of the porosity. The highest adsorption capacity at 30 and 70 degrees C for the amine impregnated activated carbons was probably due to a combination of physical adsorption inherent from the parent sample and chemical adsorption of the loaded amine groups. The CO(2) adsorption capacities for the activated amine impregnated samples are higher than those previously published for fly ash carbons without activation (68.6 vs. 45mg CO(2)/g sorbent).     

Preparation and characterization of sorbents prepared from ash (waste material) for sulfur dioxide (SO2) removal

Sorbents synthesized from various types of ash (coal fly ash, coal bottom ash, oil palm ash, and incinerator ash) for flue gas desulfurization were investigated. The sorbents were prepared by mixing the ashes with calcium oxide and calcium sulfate using the water hydration method. The effects of various sorbent preparation variables, such as the hydration period, the ratio of calcium oxide to ash, and the amount of calcium sulfate, on the Brunauer-Emmett-Teller (BET)-specific surface area of the resulting sorbent were studied using a two-level full factorial design. The surface area of the sorbents obtained range from 15.4 to 122.1m²/g. Regression models were developed to correlate the significant variables to the surface area of the sorbents. An analysis of variance (ANOVA) showed that the model was significant at a confidence level of 95%. It was found that apart from all the individual variables studied, interactions between variables also exerted a significant influence on the surface area of the sorbent. From the activity test results, it was found that sorbents prepared from coal fly ash and oil palm ash have the highest SO₂ absorption capacity. Scanning electron microscope (SEM) analysis showed that the sorbent was composed of a compound with a high structural porosity, while an X-ray diffraction spectrum showed that calcium aluminum silicate hydrate compounds are the main products of the hydration reaction.     

湿法同时脱硫脱硝工艺中脱硝吸收剂的研究现状

综述了目前国内外开发的湿法烟气脱硫、脱硝一体化技术中对脱硝吸收剂的研究现状,主要介绍了亚氯酸钠、过氧化氢、高锰酸钾、亚铁络合物、钴络合物以及尿素、亚硫酸铵。分析了各种吸收剂的优缺点,并对湿法脱硝吸收剂的应用前景进行了展望。     

Absorption characteristics of potassium carbonate-based solutions with rate promoters and corrosion inhibitors

In this research, absorbents for CO₂ capture were prepared by blending 30 wt% potassium carbonate, 3 wt% of a rate promoter, and 1 wt% of a corrosion inhibitor. Pipecolic acid, sarcosine, and diethanolamine were chosen as rate promoter candidates. Based on a rate promoter screening test for CO₂ loading capacity and absorption rate, pipecolic acid and sarcosine were selected to be used as rate promoters. 1,2,3-benzotriazole and ammonium thiocyanate were chosen as corrosion inhibitors, and they were mixed with a 30 wt% potassium carbonate-based absorbent mixture containing one of the rate promoters. The absorption rates for four absorbent solutions (30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% 1,2,3-benzotriazole, 30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% ammonium thiocyanate, 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% 1,2,3-benzotriazole, and 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% ammonium thiocyanate) were measured, tabulated, and graphically displayed. These types of absorbents can be used for capturing CO₂ under high temperature and pressure conditions, such as those found in coal-fired power plants.     

高Ca~(2+)浓度CO_2沉淀法由电石渣制备纳米CaCO_3

以NH4Cl溶液为浸取剂、CO2为碳化剂、多聚磷酸钠(STP)为添加剂,由电石渣制备纳米Ca CO3。实验结果表明:电石渣浸取液Ca2+浓度为1.0 mol/L、STP加入量为3.00%时,可制备出粒径为30~60 nm的纳米Ca CO3;STP可有效控制纳米Ca CO3的粒度和形貌;在最佳工艺条件下,由电石渣制备纳米Ca CO3的产率为80%,处理1 t电石渣产生的经济效益约为2 670元。     

液体吸收法脱除烟气中二氧化硫的研究

对烟气中SO2有机吸收剂进行了筛选，研究出一种新型烟气脱硫吸收剂－二甲基亚砜加Mn^2 。与纯二甲基亚砜相比，添加Mn^2 对烟气脱硫效率有较大的影响。同时还进行了工艺条件试验，并对新型烟气脱硫吸收剂的吸收机理进行了探讨。     

Effect of carbon dioxide injection on production of wood cement composites from waste medium density fiberboard (MDF)

The possibility of recycling waste medium density fiberboard (MDF) into wood-cement composites was evaluated. Both new fibers and recycled steam exploded MDF fibers had poor compatibility with cement if no treatment was applied, due to interference of the hydration process by the water soluble components of the fiber. However, this issue was resolved when a rapid hardening process with carbon dioxide injection was adopted. It appears that the rapid carbonation allowed the board to develop considerable strength before the adverse effects of the wood extractives could take effect. After 3-5 min of carbon dioxide injection, the composites reached 22-27% of total carbonation and developed 50-70% of their final (28-day) strength. Composites containing recycled MDF fibers had slightly lower splitting tensile strength and lower tensile toughness properties than those containing new fibers especially at a high fiber/cement ratio. Composites containing recycled MDF fibers also showed lower values of water absorption. Unlike composites cured conventionally, composites cured under CO(2) injection developed higher strength and toughness with increased fiber content. Incorporation of recycled MDF fibers into wood cement composites with CO(2) injection during the production stage presents a viable option for recycling of this difficult to manage waste material.     

Life cycle assessment of biogas upgrading technologies

This article evaluates the life cycle assessment (LCA) of three biogas upgrading technologies. An in-depth study and evaluation was conducted on high pressure water scrubbing (HPWS), as well as alkaline with regeneration (AwR) and bottom ash upgrading (BABIU), which additionally offer carbon storage. AwR and BABIU are two novel technologies that utilize waste from municipal solid waste incinerators - namely bottom ash (BA) and air pollution control residues (APC) - and are able to store CO(2) from biogas through accelerated carbonation processes. These are compared to high pressure water scrubbing (HPWS) which is a widely used technology in Europe. The AwR uses an alkaline solution to remove the CO(2) and then the solution - rich in carbonate and bicarbonate ions - is regenerated through carbonation of APC. The BABIU process directly exposes the gas to the BA to remove and immediately store the CO(2), again by carbonation. It was determined that the AwR process had an 84% higher impact in all LCA categories largely due to the energy intensive production of the alkaline reactants. The BABIU process had the lowest impact in most categories even when compared to five other CO(2) capture technologies on the market. AwR and BABIU have a particularly low impact in the global warming potential category as a result of the immediate storage of the CO(2). For AwR, it was determined that using NaOH instead of KOH improves its environmental performance by 34%. For the BABIU process the use of renewable energies would improve its impact since accounts for 55% of the impact.