Enhanced U(VI) bioreduction by alginate-immobilized uranium-reducing bacteria in the presence of carbon nanotubes and anthraquinone-2,6-disulfonate

Uranium-reducing bacteria were immobilized with sodium alginate, anthraquinone-2, 6-disulfonate (AQDS), and carbon nanotubes (CNTs). The effects of different AQDS-CNTs contents, U(IV) concentrations, and metal ions on U(IV) reduction by immobilized beads were examined. Over 97.5% U(VI) (20 mg/L) was removed in 8 hr when the beads were added to 0.7% AQDS-CNTs, which was higher than that without AQDS-CNTs. This result may be attributed to the enhanced electron transfer by AQDS and CNTs. The reduction of U(VI) occurred at initial U(VI) concentrations of 10 to 100 mg/L and increased with increasing AQDS-CNT content from 0.1% to 1%. The presence of Fe(III), Cu(II) and Mn(II) slightly increased U(VI) reduction, whereas Cr(VI), Ni(II), Pb(II), and Zn(II) significantly inhibited U(VI) reduction. After eight successive incubation-washing cycles or 8 hr of retention time (HRT) for 48 hr of continuous operation, the removal efficiency of uranium was above 90% and 92%, respectively. The results indicate that the AQDS-CNT/AL/cell beads are suitable for the treatment of uranium-containing wastewaters.     

Comparison of four supports for adsorption of reactive dyes by immobilized Aspergillus fumigatus beads

Four materials, sodium carboxymethylcellulose (Na-CMC), sodium alginate (SA), polyvinyl alcohol (PVA), and chitosan (CTS), were prepared as supports for entrapping fungus Aspergillus fumigatus. The adsorption of synthetic dyes. Reactive Brilliant Blue KN-R, and Reactive Brilliant Red K-2BP, by these immobilized gel beads and plain gel beads was evaluated. The adsorption efficiencies of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by CTS immobilized beads were 89.1% and 93.5% in 12 h, respectively. The adsorption efficiency by Na-CMC immobilized beads was slightly lower than that of mycelial pellets. But the dye culture mediums were almost completely decolorized in 48 h using the above-mentioned two immobilized beads (exceeding 95%). The adsorption efficiency by SA immobilized beads exceeded 92% in 48 h. PVA-SA immobilized beads showed the lowest adsorption efficiency, which was 79.8% for Reactive Brilliant Red K-2BP and 92.5% for Reactive Brilliant Blue KN-R in 48 h. Comparing the adsorption efficiency by plain gel beads, Na-CMC plain gel beads ranked next to CTS ones. SA and PVA-SA plain gel beads hardly had the ability of adsorbing dyes. Subsequently, the growth of mycelia in Na-CMC and SA immobilized beads were evaluated. The biomass increased continuously in 72 h. The adsorption capacity of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by Na-CMC immobilized beads was 78.0 and 86.7 mg/g, respectively. The SEM micrographs show that the surface structure of Na-CMC immobilized bead is loose and finely porous, which facilitates diffusion of the dyes.     

Experimental study on Cr(Ⅵ) reduction by Pseudomonas aeruginosa

Investigation on Cr( Ⅵ ) reduction was conducted using Pseudomonas aeruginosa. The study demonstrated that the Cr(Ⅵ) canbe effectively reduced to Cr( Ⅲ ) by Pseudomonas aeruginosa. The effects of the factors affecting Cr( Ⅵ ) reduction rate including carbon source type, pH, initial Cr(Ⅵ) concentration and amount of calls inoculum were thoroughly studied. Malate was found to yield maximum biotransformation, followed by succinate and glucose, with the reduction rate of 60.86%, 43. 76% and 28.86% respectively. The optimum pH for Cr( Ⅵ ) reduction was ?.0, with reduction efficiency of 61.71 % being achieved. With the increase of initial Cr(Ⅵ) concentration,the rate of Cr(Ⅵ) reduction decreased. The reduction was inhibited strongly when the initial Cr(Ⅵ) concentration increased to 157 mg/L. As the amount of cells inoculum increased, the rate of Cr( Ⅵ ) reduction also increased. The mechanism of Cr( Ⅵ ) reduction and final products were also analysed. The results suggested that the soluble enzymes appear to be responsible for Cr (Ⅵ) reduction by Pseudomonas aeruginosa, and the reduced Cr( Ⅲ ) was not precipitated in the form of Cr(OH)3.     

Combined effects of adsorption and photocatalysis by hybrid TiO2/ZnO-calcium alginate beads for the removal of copper

The use of nanosized titanium dioxide(TiO_2) and zinc oxide(ZnO) in the suspension form during treatment makes the recovering and recycling of photocatalysts difficult.Hence,supported photocatalysts are preferred for practical water treatment applications.This study was conducted to investigate the efficiency of calcium alginate(CaAlg) beads that were immobilized with hybrid photocatalysts,TiO_2/ZnO to form TiO_2/ZnO-CaAlg.These immobilized beads,with three different mass ratios of TiO_2:ZnO(1:1,1:2,and 2:1) were used to remove Cu(Ⅱ) in aqueous solutions in the presence of ultraviolet light.These beads were subjected to three cycles of photocatalytic treatment with different initial Cu(Ⅱ) concentrations(10-80 ppm).EDX spectra have confirmed the inclusion of Ti and Zn on the surface of the CaAlg beads.Meanwhile,the surface morphology of the beads as determined using SEM,has indicated differences of before and after the photocatalytic treatment of Cu(Ⅱ).Among all three,the equivalent mass ratio TiO_2/ZnO-CaAlg beads have shown the best performance in removing Cu(Ⅱ) during all three recycling experiments.Those TiO_2/ZnO-CaAlg beads have also shown consistent removal of Cu,ranging from 7.14-52.0 ppm(first cycle) for initial concentrations of10-80 ppm.In comparison,bare CaAlg was only able to remove 6.9-48 ppm of similar initial Cu concentrations.Thus,the potential use of TiO_2/ZnO-CaAlg beads as environmentally friendly composite material can be further extended for heavy metal removal from contaminated water.     

Comparison of four supports for adsorption of reactive dyes by immobilized beads

Four materials, sodium carboxymethylcellulose （Na-CMC）, sodium alginate （SA）, polyvinyl alcohol （PVA）, and chitosan （CTS）, were prepared as supports for entrapping fungus Aspergillusfumigatus. The adsorption of synthetic dyes, Reactive Brilliant Blue KN- R, and Reactive Brilliant Red K-2BP, by these immobilized gel beads and plain gel beads was evaluated. The adsorption efficiencies of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by CTS immobilized beads were 89.1% and 93.5% in 12 h, respectively. The adsorption efficiency by Na-CMC immobilized beads was slightly lower than that of mycelial pellets. But the dye culture mediums were almost completely decolorized in 48 h using the above-mentioned two immobilized beads （exceeding 95%）. The adsorption efficiency by SA immobilized beads exceeded 92% in 48 h. PVA-SA immobilized beads showed the lowest adsorption efficiency, which was 79.8% for Reactive Brilliant Red K-2BP and 92.5% for Reactive Brilliant Blue KN-R in 48 h. Comparing the adsorption efficiency by plain gel beads, Na-CMC plain gel beads ranked next to CTS ones. SA and PVA-SA plain gel beads hardly had the ability of adsorbing dyes. Subsequently, the growth of mycelia in Na-CMC and SA immobilized beads were evaluated. The biomass increased continuously in 72 h. The adsorption capacity of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by Na-CMC immobilized beads was 78.0 and 86.7 mg/g, respectively. The SEM micrographs show that the surface structure of Na-CMC immobilized bead is loose and finely porous, which facilitates diffusion of the dyes.     

Toxicity of the xenoestrogen nonylphenol and its biodegradation by the alga Cyclotella caspia

Alkylphenols (APs), the breakdown products of alkylphenol polyethoxylates that are widely used as surfactants, have been proven to exert estrogenic effects. With industrial development, higher concentrations of APs are discharged into aquatic environments. Nonylphenol (NP), the most noxious AP, is included in the blacklist of several countries. The toxicity of NP to the alga Cyclotella caspia and the biodegradation of NP by C. caspia were studied in the laboratory. The median effective concentration at 96 hr (96 hr EC50 ) of NP for C. caspia was found to be 0.18 mg/L. Five toxicity and three degradation indices were selected for toxicity and biodegradation experiments, respectively, in five or three concentrations of NP set by the 96 hr EC50 of NP. The algal growth rate and chlorophyll a contents decreased as NP concentration increased. The main manifestations of morphological deformity of the cells included volume expansion and the presence of cytoplasmic inclusions (lipid droplets). The abnormality rate of the cells increased with NP concentration and time, and was 100% at 0.22 and 0.26 mg/L of NP after 192 hr of culture. Superoxide dismutase activity initially increased and then declined at a higher NP toxicity of greater than 0.18 mg/L. After 192 hr of culture, the biodegradation rates of NP by C. caspia with initial concentrations of 0.14, 0.18, and 0.22 mg/L were 37.7%, 31.7%, and 6.5%, respectively. The kinetic equation of C. caspia biodegradation on NP was correlated with algal growth rate and initial NP concentration.     

Nitrification characteristics of nitrobacteria immobilized in waterborne polyurethane in wastewater of corn-based ethanol fuel production

A technology to achieve stable and high ammonia nitrogen removal rates for corn distillery wastewater (ethanol fuel production) treatment has been designed. The characteristics of nitrifying bacteria entrapped in a waterborne polyurethane (WPU) gel carrier were evaluated after acclimation. In the acclimation period, nitrification rates of WPU-immobilized nitrobacteria were monitored and polymerase chain reaction (PCR) was also carried out to investigate the change in ammonium-oxidizing bacteria. The results showed that the pellet nitrification rates increased from 21 to 228 mg-N/(L-pellet. hr) and the quantity of the ammonia oxidation bacteria increased substantially during the acclimation. A continuous ammonia removal experiment with the anaerobic pond effluent of a distillery wastewater system was conducted with immobilized nitrifying bacteria for 30 days using an 80 L airlift reactor with pellets at a fill ratio of 15% (V/V). Under the conditions of 75 mg/L influent ammonia, hydraulic retention time (HRT) of 3.7--5.6 hr, and dissolved oxygen (DO) of 4 mg/L, the effluent ammonia concentration was lower than 10 mg/L and the ammonia removal efficiency was 90%. While the highest ammonia removal rate, 162 mg-N/(L-pellet.hr), was observed when the HRT was 1.3 hr.     

Immobilization study of biosorption of heavy metal ions onto activated sludge

Activated sludge was immobilized into Ca-alginate beads via entrapment, and biosorption of three heavy metal ions, copper(Ⅱ), zinc(Ⅱ), and chromimum(Ⅱ), from aqueous solution in the concentration range of 10-100 mg/L was studied by using both entrapped activated sludge and inactivated free biomass at pH≤5. A biphasic metal adsorption pattern was observed in all immobilized biomass experiments. The biosorption of metal ions by the biosorbents increased with the initial concentration increased in the medium. The adsorption rate of immobilized pre-treated activated sludge(PAS) was much lower than that of free PAS due to the increase in mass transfer resistance resulting from the polymeric matrix. Biosorption equilibrium of beads was established in about 20 h and the adsorbed heavy metal ions did not change further with time. No significant effect of temperature was observed in the test for free biomass while immobilized PAS appeared to be strong temperature dependent in the test range of 10 and 40℃.Besides, the content of activated sludge in the calcium alginate bead has an influence on the uptake of heavy metals. The sorption equilibrium was well modeled by Langmuir isotherm, implying monomolecular adsorption mechanism. Carboxyl group in cell wall played an important role in surface adsorption of heavy metal ions on PAS.     

Performance and mechanism of Cr(Ⅵ) removal by zero-valent iron loaded onto expanded graphite

Zero-valent iron(ZⅥ) was loaded on expanded graphite(EG) to produce a composite material(EG-ZⅥ) for efficient removal of hexavalent chromium(Cr(Ⅵ)). EG and EG-ZⅥ were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM),Fourier-transform infrared(FTIR) spectroscopy and Brunauer–Emmett–Teller(BET) analysis. EG-ZⅥ had a high specific surface area and contained sub-micron sized particles of zero-valent iron. Batch experiments were employed to evaluate the Cr(Ⅵ) removal performance. The results showed that the Cr(Ⅵ) removal rate was 98.80% for EG-ZⅥ,which was higher than that for both EG(10.00%) and ZⅥ(29.80%). Furthermore, the removal rate of Cr(Ⅵ) by EG-ZⅥ showed little dependence on solution p H within a p H range of 1–9.Even at pH 11, a Cr(Ⅵ) removal rate of 62.44% was obtained after reaction for 1 hr. EG-ZⅥ could enhance the removal of Cr(Ⅵ) via chemical reduction and physical adsorption,respectively. X-ray photoelectron spectroscopy(XPS) was used to analyze the mechanisms of Cr(Ⅵ) removal, which indicated that the ZⅥ loaded on the surface was oxidized, and the removed Cr(Ⅵ) was immobilized via the formation of Cr(III) hydroxide and Cr(III)–Fe(III)hydroxide/oxyhydroxide on the surface of EG-ZⅥ.     

Copper biosorption on immobilized seaweed biomass： Column breakthrough characteristics

The biosorption of copper by the brown seaweed Sargassum baccularia,immobilized onto polyvinyl alcohol(PVA)gel beads, was investigated with fixed-bed experiments.Laboratory-scale column tests were performed to determine breakthrough curves with varying flow rates and feed concentrations.A theoretical fixed-bed model,known as the Bohart-Adams equation,was evaluated in simulating the experimental breakthrough curves.The Bohart-Adams model qualitatively predicted the breakthrough trends.PVA- immobilized seaweed biomass beads were amenable to efficient regeneration with aqueous solution containing the chelating agent ethylenediaminetetraacetic acid(EDTA).The biosorbent retained most of its original uptake capacity over three cycles of use.The excellent reusability of the biosorbent could lead to the development of a viable metal remediation technology.     

Nanoscale zero-valent iron/magnetite carbon composites for highly efficient immobilization of U(Ⅵ)

Nanoscale zerovalent iron/magnetic carbon(NZVI/MC) composites were successfully synthesized by simply calcining yellow pine and iron precursors. NZVI/MC pyrolyzed at 800°C(NZVI/MC800) had a higher percentage of NZVI and displayed better resistance to aggregation and oxidation of NZVI than samples prepared at other temperatures. The NZVI/MC800 material was applied for the elimination of U(Ⅵ) from aqueous solutions. The results suggested that the NZVI/MC800 displayed excellent adsorption capacity(203.94 mg/g)toward U(Ⅵ). The significant adsorption capacity and fast adsorption kinetics were attributed to the presence of well-dispersed NZVI, which could quickly reduce U(Ⅵ) into U(Ⅳ), trapping the guest U(Ⅳ) in the porous biocarbon matrix. The removal of U(Ⅵ) on the NZVI/MC samples was strongly affected by solution pH. The NZVI/MC samples also displayed outstanding reusability for U(Ⅵ) removal after multiple cycles. These findings indicate that NZVI/MC has great potential for remediation of wastewater containing U(Ⅵ).     

Immobilization of activated sludge using improved polyvinyl alcohol （PVA） gel

The microbial immobilization method using polyvinyl alcohol(PVA)gel as an immobilizing material was improved and used for entrapment of activated sludge.The oxygen uptake rate(OUR)was used to characterize the biological activity of immobilized activated sludge.Three kinds of PVA-immobilized particles of activated sludge,that is,PVA-boric acid beads,PVA-sodium nitrate beads and PVA-orthophosphate beads were prepared,and their biological activity was compared by measuring the OUR value.The bioactivity of both autotrophic and heterotrophic microorganisms of activated sludge was determined using different synthetic wastewater media (containing 250 mg/L COD and 25 mg/L NH_4~ -N).The experimental results showed that the bioactivity and stability of the three kinds of immobilized activated sludge was greatly improved after activation.With respect of the bioactivity and the mechanical stability,the PVA-orthophosphate method may be a promising and economical technique for microbial immobilization.     

Removal of ammonium-N from ammonium-rich sewage using an immobilized Bacillus subtilis AYC bioreactor system

A self-design bioreactor system employing a fixed bed operation process with immobilized Bacillus subtilis AYC beads for NH4 +-N removal from slightly polluted water was proposed. Polyvinyl alcohol and Na-alginate were used as a gel matrix to entrap Bacillus subtilis AYC to form the immobilized beads. The NH4 +-N removal process was studied in a intermittent operation mode to examine the start-up and steady state behaviors of the immobilized AYC in the reactor. The results indicated that the reactor was in the start-up state during the first week. NH4 +-N began to be steadily removal since the second week, and the nitrogen removal rate was between 84.61% and 96.19% when the hydraulic retention time (HRT) was 30 min. To apply Bacillus subtilis AYC to develop a practical nitrogen removal system and further understand its nitrogen removal ability, the bioreactor was continuously operated under different experimental perameters. The results showed that under the optimum conditions of an HRT of 20 min and DO of 3.77–5.80 mg/L, the NH4 +-N removal rate reached 99.55%. The NH4 +-N removal rate increased as the C/N ratio increased. However, a high C/N may cause a high residual carbon level in the effluent, therefore, the most suitable C/N ratio was 10. In addition, the results showed that the bioreactor system could remove many types of nitrogen such as NH4 +-N, NO3??-N and organic-N, and had a good performance for inorganic nitrogen removal from sewage.     

Effects of typical algae species (Aphanizomenon flosaquae and Microcystis aeruginosa) on photoreduction of Hg2+ in water body

Photoreduction characteristics of divalent inorganic mercury(Hg~(2+)) in the presence of specific algae species are still not well known. Laboratory experiments were conducted in the present study to identify the effects of different concentrations of living/dead algae species, including Aphanizomenon flosaquae(AF) and Microcystis aeruginosa(MA), on the photoreduction rate of Hg~(2+)under various light conditions. The experimental results showed that percentage reduction of Hg~(2+)was significantly influenced by radiation wavelengths, and dramatically decreased with the presence of algae. The highest percentage reduction of Hg~(2+)was induced by UV-A, followed by UV-B, visible light and dark for both living and dead AF, and the order was dark UV-A UV-B visible light for both living and dead MA. There were two aspects, i.e., energy and attenuation rate of light radiation and excrementitious generated from algae metabolisms, were involved in the processes of Hg~(2+)photoreduction with the presence of algae under different light conditions. The percentage reduction of Hg~(2+)decreased from 15% to 11% when living and dead AF concentrations increased by 10 times(from 106 to 105 cells/mL), and decreased from 11% to ～ 9% in the case of living and dead MA increased. Algae can adsorb Hg~(2+)and decrease the concentration of free Hg~(2+), thus inhibiting Hg~(2+)photoreduction, especially under the conditions with high concentrations of algae. No significant differences were found in percentage reduction of Hg~(2+)between living and dead treatments of algae species.The results are of great importance for understanding the role of algae in Hg~(2+)photoreduction.     

Tyrosinase-modified carbon felt-based flow-biosensors: The role of ultra-sonication in shortening the enzyme immobilization time and improving the sensitivity for p-chlorophenol

Tyrosinase (TYR) was covalently immobilized onto amino-functionalized carbon felt surface via glutaraldehyde-coupling under ultrasonic treatment for 10 min. The resulting TYR-immobilized carbon felt was used as a working electrode unit of bioelectrocatalytic flow-through detector for TYR substrates (catechol, p-chlorophenol (p-CP), p-cresol, phenol etc.). Cathodic peak currents based on the electroreduction of enzymatically produced o-quinones were detected at –50 mV vs. Ag/AgCl. Compared with previous work in which TYR was immobilized onto amino-functionalized carbon felt for 16 hr without the ultrasonic treatment, we succeeded in (1) shortening the enzyme immobilization time from 16 hr to 10 min, (2) enhancing the sensitivity of p-CP, and (3) improving the operational stability of p-CP. The ultrasonic treatment during the TYR immobilization step would lead to certain changes in the structure of the immobilized TYR and the morphology of the immobilized TYR-layer on the carbon felt surface.     

In vitro immunotoxicity of untreated and treated urban wastewaters using various treatment processes to rainbow trout leucocytes

Municipal effluents are known to impede the immune system of aquatic organisms. The purpose of this study was to examine the immunotoxicity of urban wastewaters before and after 6 treatment processes from 12 cities toward trout leucocytes. Freshly prepared trout leucocytes were exposed to increasing concentrations of solid phase (C18) extracts of wastewaters for 24 hr at 15℃. Immunocompetence was determined by following changes in leucocyte viability and the proportion of cells able to ingest at least one (immunoactivity) and at least three (immunoefficiency) fluorescent beads. The influents were treated by six different treatment strategies consisting of facultative aerated lagoons, activated sludge, biological aerated filter, biological nutrient removal, chemically-assisted physical treatment and trickling filter/solid contact. Water quality parameters of the wastewaters revealed that the plants effectively removed total suspended solids and reduced the chemical oxygen demand. The results revealed that the effluents' immunotoxic properties were generally more influenced by the properties of the untreated wastewaters than by the treatment processes. About half of the incoming influents decreased leucocyte viability while 4 treatment plants were able to reduce toxicity. The influents readily increased phagocytosis activity for 8/12 influents while it was decreased in 4/12 influents. This increase was abolished for 4/12 of the effluents using treatments involving biological and oxidative processes. In conclusion, municipal effluents have the potential to alter the immune system in fish and more research will be needed to improve the treatments of wastewaters to better protect the quality of the aquatic environment.     

Characterization of arsenate transformation and identification of arsenate reductase in a green alga Chlamydomonas reinhardtii

Arsenic (As) is a pervasive and ubiquitous environmental toxin that has created catastrophic human health problems world-wide. Chlamydomonas reinhardtii is a unicellular green alga, which exists ubiquitously in freshwater aquatic systems. Arsenic metabolism processes of this alga through arsenate reduction and sequent store and efflux were investigated. When supplied with 10 mol/L arsenate, arsenic speciation analysis showed that arsenite concentration increased from 5.7 to 15.7 mg/kg dry weight during a 7-day period, accounting for 18%–24% of the total As in alga. When treated with different levels of arsenate (10, 20, 30, 40, 50 mol/L) for 7 days, the arsenite concentration increased with increasing external arsenate concentrations, the proportion of arsenite was up to 23%–28% of the total As in alga. In efflux experiments, both arsenate and arsenite could be found in the efflux solutions. Additionally, the efflux of arsenate was more than that of arsenite. Furthermore, two arsenate reductase genes of C. reinhardtii (CrACR2s) were cloned and expressed in Escherichia coli strain WC3110 (ΔarsC) for the first time. The abilities of both CrACR2s genes to complement the arsenatesensitive strain were examined. CrACR2.1 restored arsenate resistance at 0.8 mmol/L. However, CrACR2.2 showed much less ability to complement. The gene products were demonstrated to reduce arsenate to arsenite in vivo. In agreement with the complementation results, CrACR2.1 showed higher reduction ability than CrACR2.2, when treated with 0.4 mmol/L arsenate for 16 hr incubation.     

Removal of hexavalent chromium from contaminated waters by ultrasound-assisted aqueous solution ball milling

Batch mode experiments were conducted to study the removal of hexavalent chromium(Cr(Ⅵ)) from aqueous solutions using ultrasound-assisted aqueous solution ball milling.The results show that the reduction rate of Cr(Ⅵ) by ultrasound-assisted aqueous solution ball milling was significantly faster than that by ball milling or ultrasound treatment alone,and an initial Cr(Ⅵ) concentration of 166 mg/L could be decreased to 0.35 mg/L at 120 min.The decisive factors, including initial concentration of Cr(Ⅵ), p H value, ultrasonic frequency and filling gas, were studied. It was found that the optimal ultrasonic frequency for ultrasound-assisted aqueous solution ball milling device was 20 k Hz, and the rate of Cr(Ⅵ)reduction as a function of filling gas followed the order: Ar air N_2 O_2. Samples were characterized by X-ray diffraction, fluorescence measurements, atomic absorption and the diphenylcarbazide colorimetric method. The Cr(Ⅵ) transformed into a precipitate that could be removed from the contaminated water, after which the water could be reused.     

Biodegradation of oil wastewater by free and immobilized Yarrowia lipolytica W29

The ability of Yarrowia lipolytica W29 immobilized by calcium alginate to degrade oil and chemical oxygen demand(COD) was examined.The degradation rules of oil and COD by immobilized cells with the cell density of 6.65 × 106 CFU/mL degraded 2000 mg/L oil and 2000 mg/L COD within 50 h at 30℃(pH 7.0,150 r/min),similarly to those of free cells,and the degradation effciencies of oil and COD by immobilized cells were above 80%,respectively.The factors affecting oil and COD degradation by immobilized cells were i...     

Immobilization of an enzyme from a Fusarium fungus WZ-I for chlorpyrifos degradation

The free enzyme extracted from WZ-I,which was identified as Fusarium LK.ex Fx,could effectively degrade chlorpyrifos,an organophosphate insecticide.The methods of immobilizing this free enzyme and determined its degradation-related characteristics were investigated.The properties of the immobilized enzyme were compared with those of the free enzyme.The optimal immobilization of the enzyme was achieved in a solution of 30 g/L sodium alginate at 4°C for 4-12 hr.The immobilized enzyme showed the maximal activity at pH 8.0,45°C.The maximum initial rate and the substrate concentration of the immobilized enzyme were less than that of the free enzyme.The immobilized enzyme,therefore,had a higher capacity to withstand a broader range of temperatures and pH conditions than the free enzyme.With varying pH and temperatures,the immobilized enzyme was more active than the free enzyme in the degradation reaction.In addition,the immobilized enzyme exhibited only a slight loss in its initial activity,even after three repeated uses.The results showed that the immobilized enzyme was more resistant to different environmental conditions,suggesting that it was viable for future practical use.