Occurrence of organic pollutants in recovered soil fines from construction and demolition waste

The objective of this study was to characterize recovered soil fines from construction and demolition (C&D) waste recycling facilities for trace organic pollutants. Over a period of 18 months, five sampling trips were made to 14 C&D waste recycling facilities in Florida. Screened soil fines were collected from older stockpiles and newly generated piles at the sites. The samples were analyzed for the total concentration (mg/kg) of a series of volatile organic compound (VOCs) and semi-volatile organic compounds (semi-VOCs). The synthetic precipitation leaching procedure (SPLP) test was also performed to evaluate the leachability of the trace organic chemicals. During the total analysis only a few volatile organic compounds were commonly found in the samples (trichlorofluoromethane, toluene, 4-isopropyltoluene, trimethylbenzene, xylenes, and methylene chloride). A total of nine VOCs were detected in the leaching test. Toluene showed the highest leachability among the compounds (61.3-92.0%), while trichlorofluoromethane, the most commonly detected compound from both the total and leaching tests, resulted in the lowest leachability (1.4-39.9%). For the semi-VOC analysis, three base-neutral semi-VOC compounds (bis(2-ethylhexyl)phthalate, butyl benzyl phthalate, and di-n-butyl phthalate) and several PAHs (acenaphthene, pyrene, fluoranthene, and phenanthrene) were commonly detected in C&D fines samples. These compounds also leached during the SPLP leaching test (0.1-25%). No acid extractable compounds, pesticides, or PCBs were detected. The results of this study were further investigated to assess risk from land applied recovered soil fines by comparing total and leaching concentrations of recovered soil fines samples to risk-based standards. The results of this indicate that the organic chemicals in recovered soil fines from C&D debris recycling facilities were not of a major concern in terms of human risk and leaching risk to groundwater under reuse and contact scenarios.     

Method development and implementation for co-planar polychlorinated biphenyls (PCBs)

The Emission Measurement Center (EMC) in the Environmental Protection Agency's Office of Air Quality Planning and Standards was directed to conduct an emissions test program at a sewage sludge incinerator in support of a Maximum Achievable Control Technology (MACT) standard. One pollutant category of concern at these facilities was polychlorinated biphenyls, or PCBs. An objective of the test program was to measure co-planar PCBs in the incinerator emissions, the sewage sludge introduced to the incinerator, and the scrubber water effluent used in controlling the incinerator emissions. Co-planar PCB congeners are those having four or more chlorine atoms with only a few substitutions in the ortho positions, i.e. positions designated 2, 2', 6, and 6'. Thirteen PCB compounds are sometimes referred to as the "WHO PCBs," because the World Health Organization (WHO) has derived toxic equivalency factors for these congeners. Studies have shown that these dioxin-like compounds can react with the aryl hydrocarbon receptor. This same reaction is believed to initiate adverse health effects for dioxin and furan congeners. In order to conduct the co-planer PCB testing, the EMC had to develop analytical methods that could measure the 13 co-planar PCBs. The purpose of the test program was to develop, evaluate, and implement analytical test methods capable of measuring co-planar PCBs in three matrices: incinerator stack gases, sewage sludge, and scrubber water effluents. The paper summarizes the initial development work that was performed in preparation of analytical test protocols that could measure co-planar PCBs in air, water, and sludge matrices. Following the method development, a MACT emissions test program was conducted at a sewage sludge facility in July 1999 and these data are also summarized in the paper.     

Safety management by use of laser mass spectrometry of polychlorinated biphenyls (PCBs) in the processed gas and work environment of a PCB disposal plant

This study demonstrates the applicability of laser mass spectrometry for safety management of the processed gas and the work environment in a polychlorinated biphenyl (PCB) disposal plant. By utilization of laser ionization/ion trapping storage/time-of-flight mass spectrometry (LI-IT-TOFMS), we analyzed gaseous PCBs from scrap capacitors with on-line detection. It was confirmed that few contaminants were detected in the spectrum. By the effect of laser-induced selective ionization, it was considered that there was little interference with the mass range of PCBs. The accuracy of LI-IT-TOFMS when analyzing environmental gas was almost the same as that for the PCB standard gas. It was possible to perform on-line analysis of the work environment for over 2000 h (120 000 data points). LI-IT-TOFMS was thus shown to be a very useful method for ensuring the safety of the work environment in disposal plants for PCBs.     

Treatment of Sydney N.S. tar pond sludge in a pilot‐scale rotary kiln

Tar pond wastes from Sydney, Nova Scotia, containing 50 ppm or more of polychlorinated biphenyls (PCBs) were treated in a pilot‐scale rotary kiln. In order to use the existing feed system attached to the rotary kiln, the wastes were first oven‐dried. Stack gas sampling was conducted during the test, which included measurement of volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), semi‐volatile organic compounds (SVOCs), HCl, and metals. The purpose of this study was to determine emissions from treatment of the tar pond waste using rotary kiln technology. It was found that the dried sludge could sustain combustion in the kiln without any supporting fuel. The emissions of polychlorinated dibenzodioxins/furans (PCDD/Fs) were higher than the Canadian Council of Ministers of the Environment (CCME) air emissions guidelines, and the reasons for this are discussed. © 2008 Wiley Periodicals, Inc.     

Remediation of persistent organic pollutants (POPs) in two different soils

Persistent organic pollutants (POPs) are a set of chemicals that are toxic, persist in the environment for long periods of time, and biomagnify as they move up through the food chain. The most widely used method of POP destruction is incineration, which is expensive and could result in undesirable by‐products. An alternative bioremediation technology, which is cheaper and environ‐mentally friendly, was tested during this experiment. Two different soil types containing high and low organic matter (OM) were spiked with 100 mg/kg each of pyrene and Aroclor 1248 and planted with three different species of grasses. The objective of the study was to determine residue recovery levels (availability) and potential effectiveness of these plant species for the remediation of POPs. The results showed that recovery levels were highly dependent on the soil organic matter content—very low in all treatments with the high OM content soil compared to recoveries in the low OM soil. This indicates that availability, and, hence, biodegradability of the contaminants is dependent on the organic matter content of the soil. Moreover, the degree of availability was also significantly different for the two classes of chemicals. The polyaromatic hydrocarbon (PAH) recovery (availability) was extremely low in the high organic matter content soil compared to that of the polychlorinated biphenyls (PCBs). In both soil types, all of the plant species treatments showed significantly greater PCB biodegradation compared to the unplanted controls. Planting did not have any significant effect on the transformation of the PAHs in both soil types; however, planting with switchgrass was the best remedial option for both soil types contaminated with PCB. © 2005 Wiley Periodicals, Inc.     

Polybrominated diphenyl ethers (PBDEs) in leachates from selected landfill sites in South Africa

The last few decades have seen dramatic growth in the scale of production and the use of polybrominated diphenyl ethers (PBDEs) as flame retardants. Consequently, PBDEs such as BDE -28, -47, -66, -71, -75, -77, -85, -99, -100, -119, -138, -153, -154, and -183 have been detected in various environmental matrices. Generally, in South Africa, once the products containing these chemicals have outlived their usefulness, they are discarded into landfill sites. Consequently, the levels of PBDEs in leachates from landfill sites may give an indication of the general exposure and use of these compounds. The present study was aimed at determining the occurrence and concentrations of most common PBDEs in leachates from selected landfill sites. The extraction capacities of the solvents were also tested. Spiked landfill leachate samples were used for the recovery tests. Separation and determination of the PBDE congeners were carried out with a gas chromatograph equipped with Ni63 electron capture detector. The mean percentage recoveries ranged from 63% to 108% (n=3) for landfill leachate samples with petroleum ether giving the highest percentage extraction. The mean concentrations of PBDEs obtained ranged from ND to 2670pgl(-1), ND to 6638pgl(-1), ND to 7230pgl(-1), 41 to 4009pgl(-1), 90 to 9793pgl(-1) for the Garankuwa, Hatherly, Kwaggarsrand, Soshanguve and Temba landfill sites, respectively. Also BDE -28, -47, -71 and BDE-77 were detected in the leachate samples from all the landfill sites; and all the congeners were detected in two of the oldest landfill sites. The peak concentrations were recorded for BDE-47 at three sites and BDE-71 and BDE-75 at two sites. The highest concentration, 9793+/-1.5pgl(-1), was obtained for the Temba landfill site with the highest BOD value. This may suggest some influence of organics on the level of PBDEs. Considering the leaching characteristics of brominated flame retardants, there is a high possibility that with time these compounds may infiltrate into the groundwater around the sites since most of the sites are not adequately lined.     

Legacy PCB building remediation

Polychlorinated biphenyls (PCBs) came onto the scene as an environmental threat quickly after they were discovered in humans and wildlife by Jensen in 1966. By October 1970, it was reported that PCBs were “truly ubiquitous pollutants” as PCBs were found at detectable concentrations in environmental samples throughout the world. Before 1971, the U.S. Environmental Protection Agency (EPA) reported that 26% of PCBs sold were used in open‐end use applications, such as caulks, sealants, plasticizers, surface coatings, ink, adhesive, and carbonless paper. Processing and distribution of PCBs in commerce were largely banned in the U.S. after July 1979 with certain continued uses authorized by the EPA. While PCBs were banned a long time ago, the ban had no immediate tangible effect on the continued use of regulated levels of PCBs in buildings constructed before the bans were implemented. Legacy buildings with PCB‐containing building materials continue to represent potential sources of indoor air, dust, outdoor air, and soil contamination. Where PCBs are present in building materials, they have the potential to pose a risk to building occupants. Proper removal of PCB‐containing materials is a highly effective approach to abating the risk. The removal can range from targeting specific building PCB‐containing materials through demolition of the building. Engineering and administrative controls can also be useful tools when addressing the risks posed by PCB‐containing materials.     

Solid state dehalogenation of PCBs in contaminated soil using NaBH4

In this work we present the results of an experimental study on the abatement of polychlorinated biphenyl (PCBs) in contaminated soil using a high energy milling technique, that promotes a reaction only by impact between milling bodies. A sample of soil from a controlled landfill was treated with powdered NaBH(4) using two different hydride/soil ratios (5 and 2.5% w/w). The efficiency of the dehalogenation/hydrogenation reaction was studied as a function of the milling time (3.5 up to 30 h). After each run, the total PCBs content and the production of inorganic chloride were measured. The complete abatement was obtained with a starting PCBs concentration of about 2600 mg/kg. The residual PCBs concentration resulted to be <0.2 mg/kg. The final products of the treatment were biphenyl and NaCl. Other toxic or hazardous organic by-products were not generated. Boron was found as boric acid.     

A performance history of the base catalyzed decomposition (BCD) process

Remediation of halogenated organic compounds—such as polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans (PCDFs)—poses a challenge because these compounds are resistant to microbial attack and to degradation by many common chemicals. Since the mid-1980s, the Environmental Protection Agency's (EPA's) Office of Research and Development in Cincinnati, Ohio—the National Risk Management Research Laboratory (NRMRL)—has funded research and development efforts to develop specialized, chemical dehalogenation processes for detoxifying PCBs and related compounds. NRMRL owns domestic rights for “basic process” patents on a chemical dehalogenation process commonly known as Base Catalyzed Decomposition (BCD). EPA has licensed the process to two firms for use in the United States. This article summarizes laboratory-scale, pilot-scale, and field performance data on BCD technology collected to date by various governmental, academic, and private organizations.     

Solvent extraction and soil washing treatment of contaminated soils from wood preserving sites: Bench‐scale studies

Bench‐scale solvent extraction and soil washing studies were performed on soil samples obtained from three abandoned wood preserving sites included in the National Priority List. The soil samples from these sites were contaminated with high levels of polyaromatic hydrocarbons (PAHs), pentachlorophenol (PCP), dioxins, and heavy metals. The effectiveness of the solvent extraction process was assessed using liquefied propane or dimethyl ether as solvents over a range of operating conditions. These studies have demonstrated that a two‐stage solvent extraction process using dimethyl ether as a solvent at a ratio of 1.61 per kg of soil could decrease dioxin levels in the soil by 93.0 to 98.9 percent, and PCP levels by 95.1 percent. Reduction percentages for benzo(a)pyrene (BaP) potency estimate and total detected PAHs were 82.4 and 98.6 percent, respectively. Metals concentrations were not reduced by the solvent extraction treatment. These removal levels could be significantly improved using a multistage extraction system. Commercial scale solvent extraction using liquefied gases costs about $220 per ton of contaminated soil. However, field application of this technology at the United Creosote site, Conroe, Texas, failed to perform to the level observed at bench scale due to the excessive foaming and air emission problem. Soil washing using surfactant solution and wet screening treatability studies were also performed on the soil samples in order to assess remediation strategies for sites. Although aqueous phase solubility of contaminants seemed to be the most important factor affecting removal of contaminants from soil, surfactant solutions (3 percent by weight) having nonionic surfactants with hydrophile‐lipophile balance (HLB) of about 14 (Makon‐12 and Igepal CA 720) reduced the PAH levels by an average of 71 percent, compared to no measurable change when pure deionized water was used. Large fractioza of clay and silt (<0.06mm), high le!ezielsof orgaizic contami‐ nants and hzimic acid can makesoil washing less applicable.     

Air Pollution Effects on Annual Ring Widths of Forest Trees in Mountainous Land of Izmir (Turkey)

Annual ring widths of forest trees are affected from different ecologicalfactors (e.g. climate, soil, etc.) and also from air pollution. In the areas with intensive air pollution annual ring width reductions are observed. For this reason, some methods which detect the annual ring widths, in other words, the increase or decrease in diameter increments, are used to examine air pollution. Industrial establishments found in the northern part of Izmir city (Aliaga region) affect air quality of this area negatively. In this investigation, annual ring widths of 13 Pinus brutia Ten. (Calabrian pine) and 20 Pinus nigra Arnold. (Austrian pine) from 4 mountains (Karabelen, Manisa, Kemalpasa, and Yamanlar) with different altitudes and exposures around Izmir city were detected and the effects of air pollution on these trees were determined. Intensive effects of air pollution have started in 1985, for that reason, annual ring widths were examined through a reference period before this year and a study period (1985–1998) after this year and results are statistically evaluated. Annual ring widths of tree samples in the northern exposure were affected from air pollution, and some reductions were observed. These reductions increased when there is a long drought period.     

Remediation of PCB‐Contaminated Soil Using Extraction and Destruction: Bench‐Scale Test

Polychlorinated biphenyls (PCBs) are a persistent environmental issue worldwide. This study summarizes the results obtained from a bench‐scale test of remediating PCB‐impacted soil. The research aimed to evaluate the effectiveness of extracting the PCB Aroclor 1260 from soil, transferring it to a liquid matrix, and then treating the PCB‐containing liquid using an Activated Metal Treatment System, a technology developed by NASA based on zero valent magnesium (ZVMg). The soil was from a former electrical plant area impacted by PCBs. The initial concentration of untreated soil contained an average of 4.7 ± 0.15 mg/kg of Aroclor 1260. The results showed that the mass transfer phenomena is possible using ethanol as a liquid matrix, reaching transfer results up to 93 percent. The ZVMg enabled the destruction of the Aroclor 1260, which reached 20 percent without any buildup of undesirable by‐products, such as less chlorinated PCBs.  ©2016 Wiley Periodicals, Inc.     

ART in‐well technology proves effective in treating 1,4‐dioxane contamination

A common industrial solvent additive is 1,4‐dioxane. Contamination of dissolved 1,4‐dioxane in groundwater has been found to be recalcitrant to removal by conventional, low‐cost remedial technologies. Only costly labor and energy‐intensive pump‐and‐treat remedial options have been shown to be effective remedies. However, the capital and extended operation and maintenance costs render pump‐and‐treat technologies economically unfeasible at many sites. Furthermore, pump‐and‐treat approaches at remediation sites have frequently been proven over time to merely achieve containment rather than site closure. A major manufacturer in North Carolina was faced with the challenge of cleaning up 1,4‐dioxane and volatile organic compound–impacted soil and groundwater at its site. Significant costs associated with the application of conventional approaches to treating 1,4‐dioxane in groundwater led to an alternative analysis of emerging technologies. As a result of the success of the Accelerated Remediation Technologies, LLC (ART) In‐Well Technology at other sites impacted with recalcitrant compounds such as methyl tertiarybutyl ether, and the demonstrated success of efficient mass removal, an ART pilot test was conducted. The ART Technology combines in situ air stripping, air sparging, soil vapor extraction, enhanced bioremediation/oxidation, and dynamic subsurface groundwater circulation. Monitoring results from the pilot test show that 1,4‐dioxane concentrations were reduced by up to 90 percent in monitoring wells within 90 days. The removal rate of chlorinated compounds from one ART well exceeded the removal achieved by the multipoint soil vapor extraction/air sparging system by more than 80 times. © 2005 Wiley Periodicals, Inc.     

Reduced sulfur compounds in gas from construction and demolition debris landfills

The biological conversion of sulfate from disposed gypsum drywall to hydrogen sulfide (H(2)S) in the anaerobic environment of a landfill results in odor problems and possible health concerns at many disposal facilities. To examine the extent and magnitude of such emissions, landfill gas samples from wells, soil vapor samples from the interface of the waste and cover soil, and ambient air samples, were collected from 10 construction and demolition (C&D) debris landfills in Florida and analyzed for H(2)S and other reduced sulfur compounds (RSC). H(2)S was detected in the well gas and soil vapor at all 10 sites. The concentrations in the ambient air above the surface of the landfill were much lower than those observed in the soil vapor, and no direct correlation was observed between the two sampling locations. Methyl mercaptan and carbonyl sulfide were the most frequently observed other RSC, though they occurred at smaller concentrations than H(2)S. This research confirmed the presence of H(2)S at C&D debris landfills. High concentrations of H(2)S may be a concern for employees working on the landfill site. These results indicate that workers should use proper personal protection at C&D debris landfills when involved in excavation, landfill gas collection, or confined spaces. The results indicate that H(2)S is sufficiently diluted in the atmosphere to not commonly pose acute health impacts for these landfill workers in normal working conditions. H(2)S concentrations were extremely variable with measurements occurring over a very large range (from less than 3 ppbv to 12,000 ppmv in the soil vapor and from less than 3 ppbv to 50 ppmv in ambient air). Possible reasons for the large intra- and inter-site variability observed include waste and soil heterogeneities, impact of weather conditions, and different site management practices.     

Comparative evaluation of demonstration testing of two PCB detoxification technologies

This paper presents a summary of the comparative analysis of two polychlorinated biphenyl (PCB) detoxification technologies that were evaluated in pilot scale equipment. Two treatment technologies, base catalyzed decomposition (BCD) and gas phase chemical reduction, treated materials removed from the PCB landfill in Warren County, North Carolina. There has been a remarkable amount of public opposition to this landfill. Very stringent performance criteria for soil cleanup of PCBs and dioxins and for air emissions from the treatment equipment were used, along with a number of other factors to evaluate the two technologies. The BCD technology was selected as the best performing one for this project.     

Determination of inorganic and organic priority pollutants in biosolids from meat processing industry

The biosolids (BS) generated in the wastewater treatment process of a meat processing plant were monitored and the priority pollutant content was characterized. The trace metal and organic pollutant content – polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDF) – were determined quantitatively and compared to guideline limits established by the US EPA and EU. PCBs were not detected in the solid samples, while trace metals, PAHs and PCDD/PCDF were detected in concentrations below the limits established by international standards. Toxic equivalent factors were evaluated for the biosolids, and the results proved that these wastes can be safely deposited on land or used in combustion/incineration plants. Since no previous data were found for meat processing waste, comparisons were made using municipal sewage sludge data reported in the literature. Since, this report monitored part of the priority pollutants established by the US EPA for meat and poultry processing wastewater and sludge, the results verified that low pollution loads are generated by the meat processing plant located in the southern part of Brazil. However, the BS generated in the treatment processes are in accordance with the limits established for waste disposal and even for soil fertilizer.     

Effect of polyethylene terephthalate (PET) on the pyrolysis of brominated flame retardant-containing high-impact polystyrene (HIPS-Br)

Pyrolysis of brominated flame retardant-containing high-impact polystyrene (HIPS-Br) was performed at 430°C in the presence of 0.1 wt% of polyethylene terephthalate (PET) in a Pyrex glass reactor. Two different types of brominated flame retardants (decabromodiphenyl ether and decabromodiphenyl ethane) with or without antimony trioxide (as synergist) 5 wt% were used. The presence of PET had a significant effect on the material balance, decreasing the gaseous product and increasing the residue. The type of flame retardant had no effect on the yield of liquid product; however, the presence of Sb resulted in a marked difference in the distribution of decomposition products. Analysis by a gas chromatograph equipped with a flame ionization detector showed that the hydrocarbons were distributed in the range n-C₇ to n-C₂₅ with major peaks at n-C₉ and n-C₁₇. The presence of PET increased the formation of brominated compounds by several times and affected both the type and quantity of polybrominated compounds. The liquid products obtained from the pyrolysis of HIPS-Br/PET have to be treated before they can be used     

Thermal desorption of PCB-contaminated waste at the waukegan harbor superfund site

In June 1992, SoilTech ATP Systems, Inc., completed the soil treatment phase of the Waukegan Harbor Superfund Project in Waukegan, Illinois, after approximately five months of operation. SoilTech successfully treated 12,700 tons of sediment contaminated with polychlorinated hiphenyls (PCBs) using a transportable SoilTech anaerobic thermal processor (ATP) system nominally rated at ten tons per hour throughput capacity. The SoilTech ATP technology anaerobically desorbs contaminants such as PCBs from solids and sludges at temperatures over 1,000° F. Principal products of the process are clean, treated solids and an oil condensate containing the hydrocarbon contaminants. At the Waukegan Harbor Superfund site, PCB concentrations in the sediments excavated and dredged from a ditch, lagoon, and harbor slip averaged 10,400 parts per million (ppm) (1.04 percent) and were as high as 23,000 ppm (2.3 percent). Treated soil was backfilled in an on-site containment cell. The removal efficiency of PCBs from the soil averaged 99.98 percent, relative to the project performance specification of 97 percent, and treated soil PCB concentrations were measured below 2 ppm. Approximately 30,000 gallons of PCB oil, desorbed from the feed material, were returned to the owner for subsequent off-site disposal. After modifications to the emissions control equipment, compliance with the 99.9999 percent destruction and removal efficiency (DRE) for PCBs in stack emissions required by the U.S. Environmental Protection Agency was achieved.     

The effect of solvent concentration on the use of palladized-iron for the step-wise dechlorination of polychlorinated biphenyls in soil extracts

This report describes the application of palladized iron (Pd/Fe) to the dechlorination of polychlorinted biphenyls (PCBs) at ambient temperature. Experiments supported by congener-specific analyses demonstrated that dechlorination occurs in a step-wise fashion with the meta-chlorines being more reactive than ortho-chlorines. Over the course of the laboratory experiments, complete conversion to biphenyl was observed. The process was also tested with PCBs dissolved in high (40-60%) concentrations of ethanol and isopropanol as a means of simulating solutions generated by commercial soil and solid waste extraction processes. The reaction rate was sensitive to the percentage of solvent but complete dechlorination was still indicated. Tests with soil extracts from a contaminated site demonstrated that there were no apparent interferences from asphalt and other miscellaneous debris. Short-duration tests with highly contaminated PCB solutions from a hazardous waste site demonstrated efficient dechlorination although there was a reduction in reaction rate with time.     

Fate and behavior of metal(loid) contaminants in an organic matter-rich shooting range soil: Implications for remediation

This study investigates the fate and behavior of lead (Pb), copper (Cu), antimony (Sb), and arsenic (As) in a shooting range soil. The soil samples were collected from the surface (0–15 cm) and the subsurface (15–40 cm and 40–55 cm) of a grassy and wood chip covered impact area behind a firing position. Optical microscopy images indicate significant amounts of corroded bullet fragments and organic wood chips in the surface soil. Analysis by X-ray powder diffraction (XRPD) and scanning electron microscopy electron dispersive X-ray spectroscopy (SEM-EDS) showed that metallic Pb was transformed into lead oxides (litharge PbO and massicot PbO) and lead carbonates (hydrocerussite Pb₃(CO₃)₂(OH)₂, cerussite PbCO₃, and plumbonacrite Pb₅(CO₃)₃O(OH)₂). Rietveld quantification indicated the surface soil contained 14.1% metallic Pb, 17.9% hydrocerussite, 5.2% plumbonacrite, 5.9% litharge, and 3.9% massicot on a dry weight basis, or a total of 39.7% Pb, far in excess of lead concentrations typically found in US shooting range soils. Metallic Cu (bullet jacket material) appeared stable as no secondary minerals were detected in the surface soil. As and Sb concentrations were on the order of 1,057 mg/kg and 845 mg/kg respectively. The elevated soil pH coupled with high organic carbon content is thought to have caused downward migration of metals, especially for Pb, since 4,153 mg Pb/kg was observed at a depth of 55 cm. More than 60% of Pb was concentrated in the coarse soil (> 0.425 mm) fraction, suggesting soil clean-up possible by physical soil washing may be viable. The concentrations of Pb, As, and Sb in the toxicity characteristic leaching procedure (TCLP) extracts were 8,869 mg/L, 6.72 mg/L, and 6.42 mg/L respectively, were above the USEPA non-hazardous regulatory limit (As and Pb) of 5 mg/L. The elevated Sb and As concentrations draw concern because there is historically limited information concerning these metals at firing ranges and several values exceeded local soil cleanup criteria. As the high Pb concentrations appeared to be linked to the presence of organic-rich berm cover materials, the use of wood chips as berm cover to prevent soil erosion requires reconsideration as a shooting range management practice.