Fe(III)-oxalate complexes induced photooxidation of diethylstilbestrol in water

In this work, the photooxidation of diethylstilbestrol (DES), a synthetic estrogen, was investigated in a concentric reactor under a 125 W high-pressure mercury lamp (lambda > or = 365 nm). The photooxidation efficiencies were dependent on the pH values and Fe(III)/oxalate ratios of the system, with higher efficiency at pH 3.50+/-0.05 and Fe(III)/oxalate ratio 10.0/120.0 micromol l(-1). The photooxidation reactions obeyed the law of pseudo-first-order reaction at the concentration over the range of 2.0-10.0 mg l(-1) of DES. The photooxidation rates decreased with increasing the initial concentrations of DES. For 2.0 mg l(-1) DES, the observed photooxidation rate coefficient (k(obs)) was 0.00622 min(-1). By using GC-MS and LC-MS techniques, the predominant photooxidation products DES-o-catechol ([M](+), m/z 284) and DES-4-semiquinone ([M](-), m/z 267) were respectively identified and the mechanisms for the oxidative degradation were proposed. When DES reacted with OH radicals, C atoms in 3-position were added with OH radicals to produce hydrolyzed DES radical followed by two oxidation pathways: (1) dehydrolyzing to produce DES-4-semiquinone which was oxidized further to DES-4,4'-quinone; (2) undergoing peroxidation by O(2) and getting rid of HO(2) radical to produce DES-o-catechol. After that, the two H atoms on the hydroxy group of the catechol were extracted in two individual steps to form intermediates semiquinone radical and o-quinone. The catechol intermediates underwent further oxidation, benzene ring cleavage and decarboxylation, up to mineralization ultimately.     

Polar organic marker compounds in PM2.5 aerosol from a mixed forest site in western Germany

The molecular composition of PM2.5 (particulate matter with an aerodynamic diameter <2.5 microm) aerosol samples collected during a very warm and dry 2003 summer period at a mixed forest site in Jülich, Germany, was determined by gas chromatography/mass spectrometry in an effort to evaluate photooxidation products of biogenic volatile organic compounds (BVOCs) and other markers for aerosol source characterization. Six major classes of compounds represented by twenty-four individual organic species were identified and measured, comprising tracers for biomass combustion, short-chain acids, fatty acids, sugars/sugar alcohols, and tracers for the photooxidation of isoprene and alpha-/beta-pinene. The tracers for the photooxidation of alpha-/beta-pinene include two compounds, 3-hydroxyglutaric acid and 3-methyl-1,2,3-butanetricarboxylic acid, which have only recently been elucidated. The characteristic molecular distribution of the fatty acids with a strong even/odd number carbon preference indicates a biological origin, while the presence of isoprene and terpene secondary organic aerosol products suggests that the photooxidation of BVOCs contributes to aerosol formation at this site. The sum of the median concentrations of the isoprene oxidation products was 21.2 ng m(-3), while that of the terpene oxidation products was 19.8 ng m(-3). On the other hand, the high median concentration of malic acid (37 ng m(-3)) implies that photooxidation of unsaturated fatty acids should also be considered as an important aerosol source process. In addition, the occurrence of levoglucosan and pyrogallol indicates that the site is affected by biomass combustion. Their median concentrations were 30 and 8.9 ng m(-3), respectively.     

The effect of water on gas–particle partitioning of secondary organic aerosol: II. m-xylene and 1,3,5-trimethylbenzene photooxidation systems

An investigation of the effect of relative humidity on aerosol formation from m-xylene and 1,3,5-trimethylbenzene photooxidation is reported. Experiments were performed in the presence and absence of ammonium sulfate seed particles (both aqueous and dry) to ascertain the effect of partitioning of oxidation products into a strong electrolytic solution or onto dry crystalline seed particles. In marked contrast to the α-pinene/ozone system, the final measured secondary organic aerosol yield was unaffected by the presence of gas-phase or liquid-phase water at relative humidities (RH) up to 50%. The hygroscopic nature of the aerosol generated upon photooxidation of m-xylene and 1,3,5-trimethylbenzene was examined; the hygroscopicity of the aerosol at 85% RH for both parent organics increased with the extent of the reaction, indicating that the first-generation oxidation products undergo further oxidation. Limited identification of the gas- and aerosol-phase products of m-xylene and 1,3,5-trimethylbenzene photooxidation is reported. It is evident that a more complete molecular identification of aromatic photooxidation aerosol awaits analytical techniques not yet brought to bear on this problem.     

Environmental photooxidation of dibenzothiophenes following the Amoco Cadiz oil spill

Photooxidation products of dibenzothiophenes (sulfur containing petroleum heteroaromatic hydrocarbons) were characterized in an oil slick sample obtained from a field location following the AMOCO CADIZ oil spill. The same oxidation products were formed in the laboratory by the photooxidation of a medium Arabian crude oil which contained the identical precursor hydrocarbons. Analytical techniques included fractionation by liquid/solid chromatography and characterization using high resolution gas chromatography-mass spectrometry. To the best of the author's knowledge, this represents the first reported instance for the formation of photooxidation products following an actual oil spill. A comparison of the quantities of various oxidation products was carried out by quantitative mass spectrometry using extracted ion current profiles of dibenzothiophenes and their corresponding sulfoxides. The geochemical and physiological implications of such photooxidation processes are also discussed.     

Photooxidation of arsenite by natural goethite in suspended solution

Iron and arsenic have been found to coexist in a water environment and the fate of arsenite in the aquatic system is influenced by iron. Goethite is a form of iron hydroxide, which is commonly found in sediments. In previous studies, we have used iron complexes to degrade organic pollutants. Results have shown that some organic pollutants could be totally degraded by iron complexes and our work indicated that iron might cause conversion of arsenic when irradiated. This work attempts to investigate the conversion of arsenite [As(III)] using natural goethite, as the iron source, to quantify the effect of various factors on photooxidation. We also consider the possible mechanism for photooxidation of As(III) using a suspension of natural goethite. The As(III) concentration variation under illumination was compared with the one in the dark to quantify the contribution of light to As(III) oxidation to As(V) in goethite suspended solution. The experiments under N₂ and air atmosphere confirmed the participation of dissolved oxygen. The photooxidation efficiency of As(III) under different conditions was compared to determine the effect of different environmental factors such as pH value, goethite concentration, and humic acid concentration on the photooxidation reaction. In the solution containing 100 μg L^?1 arsenite and 0.1 g?L^?1 suspended goethite at pH 3.0, nearly 80 % of As(III) was photooxidized after irradiation by a 250-W metal halogen lamp (λ?≥?313 nm) after 6 h. The effects of initial pH and goethite concentration and humic acid concentration were all examined. The results show that the greatest efficiency of photooxidation of As(III) was at pH 3.0. The extent of photooxidation decreased with increasing goethite concentration and fell sharply in the presence of humic acid under the conditions in this work. Although about 80 % of As(III) was photooxidized after irradiation by a 250-W halogen lamp at pH 3.0 in the presence of goethite suspension, photooxidation was also affected by factors such as pH, concentration of goethite, and presence of humic acid. The scavenger experiments showed that the HO? radical and photogenerated hole are the predominant oxidants in this system responsible for 87.1 % oxidation of As(III), while HO ₂ ^? /O ₂ ^?? is responsible for 12.9 % oxidation of As(III).     

Subfractionation, characterization and photooxidation of crude oil resins

Resins of five crude oils were obtained using SARA fractionation. The maltenic fraction of Blend Arabian Light, was further separated into six polar fractions. These fractions which are the constituents of the resins were analysed by FTIR spectroscopy. They appeared to be more oxidized, more aliphatic and less aromatic than asphaltenes. Photooxidation of resins showed that they are easily oxidizable and much more influenced by photooxidation than asphaltenes. The principal effect of photooxidation are: (i) increase of carbonyl group amounts and particularly formation of carboxylic groups, (ii) oxidation of sulfoxide in sulfone group, (iii) oxidation of alkyl chains and of aromatic rings (quinone structures).     

Pathway of anthracene modification under simulated solar radiation

Exposure of polycyclic aromatic hydrocarbons (PAHs) to sunlight results in rapid structural photomodification generally via oxidation reactions. These PAH modification products are in many cases more toxic than their parent compounds. In this study, anthracene (ANT), a rapidly photooxidized PAH, was irradiated with simulated solar radiation (SSR, 100 μmol m⁻² s⁻¹) in aqueous solution to examine the photomodification pathway. The photoproducts formed were identified by HPLC. The ANT product profile after 9 h in SSR was very complex, with more than 20 compounds detected. The photoproducts formed were anthraquinones, benzoic acids, benzaldehydes and phenols showing the process to be oxidative in nature. Some of the anthraquinones were themselves subject to photooxidation, and were thus intermediates in the product pathway. The kinetics of ANT photooxidation revealed a pseudo first-order reaction with a half-life of 2 h under the SSR source used. The kinetics of product formation allowed deduction of a probable photomodification pathway. This study indicates that PAH photooxidation products are likely to exist as complex, dynamically changing mixtures in PAH contaminated aquatic environments.     

高价铬及双酚A在铁-乳酸体系中的同时光处理

研究了Fe(Ⅲ)-乳酸配合物体系同时对Cr(Ⅵ)的光还原及双酚A(BPA)的光氧化处理,考察了光源、初始pH值、Fe(Ⅲ)、乳酸盐、Cr(Ⅵ)及BPA初始浓度等因素对Cr(Ⅵ)及BPA光处理效率的影响。结果表明:光照条件下,铁-乳酸配合物能有效实现对六价铬及BPA的同时光处理。同一体系中,Cr(Ⅵ)的光还原快于BPA的光氧化,Fe(Ⅲ)初始浓度的增加可同时提高Cr(Ⅵ)的光还原效率和BPA的光氧化效率;Fe(Ⅲ)-乳酸盐配合物光解产生的Fe(Ⅱ)是Cr(Ⅵ)的主要还原剂,其次级光反应中产生的.OH是BPA的氧化剂。     

Photooxidation mechanism of nitrogen-containing compounds at TiO2/H2O interfaces: an experimental and theoretical examination of hydrazine derivatives

The photocatalytic oxidation of oxalyldihydrazide, N,N'-bis(hydrazocarbonyl)hydrazide, N,N'-bis(ethoxycarbonyl)hydrazide, malonyldihydrazide, N-malonyl-bis[(N'-ethoxycarbonyl)hydrazide] was examined in aqueous TiO2 dispersions under UV illumination. The photomineralization of nitrogen and carbon atoms in the substrates into N2 gas, NH4+ (and/or NO3-) ions, and CO2 gas was determined by HPLC and GC analysis. The formation of carboxylic acid intermediates also occurred in the photooxidation process. The photocatalytic mechanism is discussed on the basis of the experimental results, and with molecular orbital (MO) simulation of frontier electron density and point charge. Substrate carbonyl groups readily adsorb on the TiO2 surface, and the bonds between carbonyl group carbon atoms and adjacent hydrazo group nitrogen atoms are cleaved predominantly in the initial photooxidation process. The hydrazo groups were photoconverted mainly into N2 gas (in mineralization yields above 70%) and partially to NH4 ions (below 10%). The formation of NO3- ions was scarcely recognized.     

Improvement of water resistance by Fe2O3/TiO2 photoelectrocatalysts for formaldehyde removal: experimental and theoretical investigation

Environmental Science and Pollution Research - TiO2-based photocatalysts are a potential technology for removing indoor formaldehyde (CHOH) owing to their strong photooxidation ability. However,...     

硝酸根紫外光降解对硝基苯甲酸的研究

以硝酸铝做光氧化剂,研究了紫外光照射下,NO-3对PNB(对硝基苯甲酸)的光降解作用.探索了NO-3投加量、模拟废水初始浓度和pH值、光照时间、溶解氧浓度对处理效果的影响.结果表明,NO-3对PNB具有良好的光氧化作用,在最佳处理条件下,NO-3光降解PNB 4 h后降解率达90.8%.廉价硝酸盐对于有机物能起到显著光...     

Photodegradation of 4-tert octylphenol in aqueous solution promoted by Fe(III)

4-Tert-octylphenol (4-t-OP), a kind of endocrine-disrupting compounds, is widely distributed in natural water surroundings but can hardly be biodegraded. The advanced oxidation processes (AOPs) have been proved to be an efficient method to degrade 4-t-OP. In this study, the photodegradation of 4-t-OP in aqueous solution promoted by Fe(III) and the photooxidation mechanism were investigated. The ferric perchlorate was added into the aqueous solution for the production of hydroxyl radical. The efficiency of mineralization was monitored by total organic carbon analyzer, and photooxidation products were determined by high-performance liquid chromatography and liquid chromatography-mass spectrometer. 4-t-OP (2.4?×?10^?5 M) in aqueous solution was completely degraded after 45 min in the presence of Fe(III) (1.2?×?10^?3 M) under UV irradiation (λ?=?365 nm). The optimal pH was 3.5. Higher Fe(III) concentration or lower initial 4-t-OP concentration led to increased photodegradation efficiency of 4-t-OP. The reaction was almost completely inhibited in the presence of 2-propanol. About 70 % mineralization of the solution was obtained after 50 h. The photooxidation product was supposed to be 4-tert-octyl catechol. 4-t-OP in aqueous solution can be degraded in the presence of Fe(III) under the solar irradiation. The photoinduced degradation is due to the reaction with hydroxyl radicals. It shows that the 4-t-OP is mineralized by the inducement of Fe(III) aquacomplexes, which exposes to solar light. Therefore, the results would provide useful information for the potential application of the AOPs to remove 4-t-OP in water surroundings.     

Photocatalytic oxidation of organic pollutants on titania-clay composites

TiO2/Ca-montmorillonite composites were prepared by wet grinding in an agate mill. Positively charged TiO2 nanoparticles are bound to the surface of the negatively charged montmorillonite layers via heterocoagulation; the clay mineral is used as adsorbent and support for the photooxidation process. Aquatic solution of 0.5mM phenol was degraded by irradiation with UV-VIS light (lambda=250-440 and 540-590 nm) in suspensions of TiO2-clay composites and significant photodegradation was observed at 40-60% TiO2/Ca-montmorillonite compositions. Synergistic effect was detected at solid/liquid interface for degradation of phenol and at solid/gas interface in the recycling flow reactors for photooxidation of ethanol and toluene vapors.     

Secondary organic aerosol production from aqueous photooxidation of glycolaldehyde: Laboratory experiments

Organic particulate matter (PM) formed in the atmosphere (secondary organic aerosol; SOA) is a substantial yet poorly understood contributor to atmospheric PM. Aqueous photooxidation in clouds, fogs and aerosols is a newly recognized SOA formation pathway. This study investigates the potential for aqueous glycolaldehyde oxidation to produce low volatility products that contribute SOA mass. To our knowledge, this is the first confirmation that aqueous oxidation of glycolaldehyde via the hydroxyl radical forms glyoxal and glycolic acid, as previously assumed. Subsequent reactions form formic acid, glyoxylic acid, and oxalic acid as expected. Unexpected products include malonic acid, succinic acid, and higher molecular weight compounds, including oligomers. Due to (1) the large source strength of glycolaldehyde from precursors such as isoprene and ethene, (2) its water solubility, and (3) the aqueous formation of low volatility products (organic acids and oligomers), we predict that aqueous photooxidation of glycolaldehyde and other aldehydes in cloud, fog, and aerosol water is an important source of SOA and that incorporation of this SOA formation pathway in chemical transport models will help explain the current under-prediction of organic PM concentrations.     

Photochemical formation of hydroxyl radicals catalyzed by montmorillonite

In this work, the photooxidation of benzene and the formation of phenol in aqueous suspensions of the iron-rich montmorillonite under irradiation of a 250W metal halide lamp (lambda> or = 365nm) were investigated. We confirmed that hydroxyl radicals (()OH) were produced by illuminating montmorillonite and was responsible for the photooxidation of benzene in aqueous suspensions of montmorillonite. Low pH value facilitated the formation of hydroxyl radicals in the pH range of 2.0-10.0. The ()OH concentration increased with increasing the concentration of montmorillonite in aqueous solutions in the range of 0-20.0gl(-1). Higher concentration like 25.0gl(-1) montmorillonite inhibited the ()OH production. Iron, predominantly free iron in the clays, is believed to be one of the most important factors determining ()OH formation. Structural irons in montmorillonite have contributions to ()OH formation, especially in the presence of carboxylate ions. The formation of ()OH from montmorillonite under irradiation of near UV and visible light indicates that clays might play important role not only in transfer through adsorption but also in transformation through oxidation of organic compounds on the surface of clay particles in air, water, soil or even top sediments.     

Degradation mechanism of azo dye C. I. reactive red 2 by iron powder reduction and photooxidation in aqueous solutions

We have made a comparison of the UV-VIS spectra of three azo dyes, C. I. reactive red 2, orange II and C. I. reactive black 8, in aqueous solutions during treatment with iron powder reduction and photooxidation. From this, we propose their mechanisms for reduction photooxidation. GC/MS analyses of the degradation products of the dye C. I. reactive red 2 demonstrated some important steps producing hydrogenated azo structure, substituted benzene and substituted naphthalene.     

A mechanistic model for mercury capture with in situ-generated titania particles: role of water vapor

A mechanistic model to predict the capture of gas-phase mercury (Hg) species using in situ-generated titania nanosize particles activated by UV irradiation is developed. The model is an extension of a recently reported model for photochemical reactions by Almquist and Biswas that accounts for the rates of electron-hole pair generation, the adsorption of the compound to be oxidized, and the adsorption of water vapor. The role of water vapor in the removal efficiency of Hg was investigated to evaluate the rates of Hg oxidation at different water vapor concentrations. As the water vapor concentration is increased, more hydroxy radical species are generated on the surface of the titania particle, increasing the number of active sites for the photooxidation and capture of Hg. At very high water vapor concentrations, competitive adsorption is expected to be important and reduce the number of sites available for photooxidation of Hg. The predictions of the developed phenomenological model agreed well with the measured Hg oxidation rates in this study and with the data on oxidation of organic compounds reported in the literature.     

Photodegradation of bisphenol Z by UV irradiation in the presence of beta-cyclodextrin

In this work, the formation of the inclusion complex of bisphenol Z (1,1-bis(4-hydroxyphenyl)cyclohexane, abbreviated as BPCH) with beta-cyclodextrin (beta-CD) has been studied, 1:1 inclusion complex can be obtained, the formation constant of the beta-CD/BPCH complex is 5.94x10(3)M(-1). The photodegradation behavior of BPCH was investigated under monochromatic UV irradiation (lambda=254 nm). The photodegradation rate constant of BPCH in aqueous solutions with beta-CD showed a 9.0-fold increase, and simultaneously the mineralization of BPCH can be enhanced by beta-CD. The influence factors on photodegradation of BPCH were also studied and described in details, such as concentration of beta-CD, initial concentration of BPCH, organic solvent and pH. The photodegradation of BPCH in the presence of beta-CD includes the direct photolysis and the photooxidation of BPCH during the photochemical process. Some predominant photodegradation products are 4-(2,4,5-trihydroxy-phenyl)-4-(4-hydroxyphenyl) butanoic acid, 5,5-bis(4-hydroxyphenyl)pentanoic acid, meta-hydroxylated BPCH, ortho-hydroxylated BPCH and 4-(1-(4-hydroxyphenyl)pentyl)phenol respectively. The enhancement of photodegradation of BPCH mainly results from moderate inclusion depth of BPCH molecule in the beta-CD cavity. This kind of inclusion structure allows BPCH molecule sufficient proximity to secondary hydroxyl groups of the beta-CD cavity, and these hydroxyl groups could be activated and converted to hydroxyl radicals under UV irradiation, which can enhance the photooxidation of BPCH.     

Diel cycles of arsenic speciation due to photooxidation in acid mine drainage from the Iberian Pyrite Belt (Sw Spain)

Twenty four hours diel cycles of arsenic speciation in Acid Mine Drainage (AMD) due to photooxidation have been reported for the first time. AMD samples were taken during 48 h (31st March and 1st April, 2005) at 6 h intervals from the effluent of a massive abandoned polymetallic sulphide mine of the Iberian Pyrite Belt (Sw Spain). Samples were preserved in situ using cationic exchange prior to analysis by coupled high performance liquid chromatography, hydride generation and atomic fluorescence spectrometry (HPLC-HG-AFS) for arsenic speciation. The results indicated the presence of inorganic arsenic species with daily means of 262mugl(-1) for As(V) and 107 microg l(-1) for As(III). No marked diel trend was observed for As(V). However, a marked diel trend was observed for As(III) in the two studied days, with maximum concentrations during nighttime (141-143 microg l(-1)) and minimum concentrations at daytime (72-77 microg l(-1)). This difference in concentration during daytime and nighttime is ca. 100%. A similar diel cycle was observed for iron. An explanation for the arsenic diel cycles observed is the light induced photooxidation of As(III) and the elimination of As(V) due to its adsorption onto Fe precipitates during the daytime. Furthermore, the diel changes in arsenic speciation emphasize the importance of designing suitable sampling strategies in AMD systems.     

Gas-phase tropospheric chemistry of organic compounds: a review

The current knowledge of the gas-phase reactions occurring in the troposphere for alkanes, alkenes, alkynes, oxygenates and aromatic hydrocarbons and their photooxidation products is reviewed,and areas of uncertainty identified.