纳米复合ZnO-TiO2晶体的制备及其光电催化性能研究

采用溶胶-凝胶法制备了纳米复合半导体ZnO-TiO2薄膜,并进行了结构和光电催化性能的测试.TiO2薄膜对五氯酚溶液的光电催化降解结果表明当输入正向偏压后,其光催化性能有较大提高.由于ZnO的掺入,半导体薄膜电极的光吸收能力增强;同时,Zn2+可能作为光生载流子的浅俘获中心,导致表面界面电荷转移加速,从而延长光生电子/空穴对的寿命并抑制其复合,有效地提高了TiO2薄膜光电催化活性.     

The enhanced PC and PEC oxidation of formic acid in aqueous solution using a Cu-TiO2/ITO film

The photocatalytic (PC) and photoelectrocatalytic (PEC) activity of Cu-TiO2/ITO films for degrading formic acid in aqueous solution was investigated in this study. Compared with a TiO2/ITO film, the degradation efficiency of formic acid on the Cu-TiO2 films increased markedly in both the PC and PEC oxidation processes. However, it was found that the photodeposited Cu metal on the Cu-TiO2 films could electrochemically dissolute during the PEC reaction, while an electrical bias with the voltage higher than 1.48 V was applied. It is believed this is a common problem occurred for several metals deposition on the TiO2 films, which results in a poor stability of the metal-deposited TiO2 electrode in PEC processes. To improve the stability of the Cu-TiO2 electrode, an alternative process between PC and PEC reactions was investigated. It was found that the dissolute Cu metal during the PEC process was re-deposited on the Cu-TiO2 film again during the PC process. The experiments with repeated runs demonstrated that this alternative process could not only overcome the loss of Cu, but also enhance the PEC oxidation efficiency of the Cu-TiO2 films.     

Photoelectrocatalytic degradation of 4,4'-dibromobiphenyl in aqueous solution on TiO₂ and doped TiO₂ nanotube arrays

Polybrominated biphenyls have been widely used as flameretardants in textile and electronic industries, and additives in plastics. Over the past few decades, much attention has been given to polybrominated biphenyls in the environment and their effects on humans. In this paper, we studied on the degradation of 4,4′-dibromobiphenyl, a typical one of polybrominated biphenyls, through photoelectrocatalytic process with TiO₂, Zr/TiO₂ and Zr, N/TiO₂ nanotube arrays. The results showed that the photoelectrocatalytic process was more efficient than photocatalytic and electrolytic process alone. The results exhibited that the photoelectrocatalytic efficiency was significantly affected by the properties of the catalysts and bias potential, and the highest photoelectrocatalytic degradation rate was achieved with Zr, N/TiO₂ at 1 V and the order was Zr, N/TiO₂ > Zr/TiO₂ > TiO₂. The mechanism was also discussed by detecting the changes of pH value, bromine anion, total organic carbon and intermediates during the process.     

Photocatalytic decomposition on nano-TiO₂: destruction of chloroaromatic compounds

Photocatalysis is applied increasingly in addressing and solving environmental and energy-related problems. Especially the TiO₂-derived catalysts attract attention because of their catalytic efficiency, wide range of applications, ease in use, and low cost (it costs about 150 Yuan a kilogram in China). This review first describes the principles of photocatalytic destruction by semiconductors and then focuses on degradation rates and reaction mechanisms in a variety of photocatalytic uses of modified TiO₂. Finally, these concepts are illustrated by selected examples relating to the photocatalytic degradation of organic persistent pollutants, such as polychlorinated benzenes (PCBz), biphenyls (PCB) and dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). And some approaches towards industrial application are analyzed.     

Solar driven nitrous acid formation on building material surfaces containing titanium dioxide: A concern for air quality in urban areas?

The photoenhanced uptake of nitrogen dioxide (NO₂) to the surface of commercially available self-cleaning window glass has been studied under controlled laboratory conditions. This material is one of an array of modern building products which incorporate titanium dioxide (TiO₂) nanoparticles and are finding increasing use in populated urban areas. Amongst the principal drivers for the use of these materials is that they are thought to facilitate the irreversible removal of pollutants such as NO₂ and organic molecules from the atmosphere and thus act to remediate air quality. While it appears that TiO₂ materials do indeed remove organic molecules from built environments, in this study we show that the photoenhanced uptake of NO₂ to one example material, self-cleaning window glass, is in fact accompanied by the substantial formation (50–70%) of gaseous nitrous acid (HONO). This finding has direct and serious implications for the use of these materials in urban areas. Not only is HONO a harmful respiratory irritant, it is also readily photolysed by solar radiation leading to the formation of hydroxyl radicals (OH) together with the re-release of NO_x as NO. The net effect of subsequent OH initiated chemistry can then be the further degradation of air quality through the formation of secondary pollutants such as ozone and VOC oxidation products. In summary, we suggest that a scientifically conceived technical strategy for air quality remediation based on this technology, while widely perceived as universally beneficial, could in fact have effects precisely opposite to those intended.     

TiO2/Ni PECO体系降解DMP的动力学和光电协同作用研究

以采用微波辅助法制备的TiO₂/Ni光电极为阳极,纤维状石墨毡材料(graphite felt,GF)为阴极,饱和甘汞电极(saturated calomel electrode, SCE)为参比电极建立TiO₂/Ni 光电催化氧化（PECO）体系。以邻苯二甲酸二甲酯（dimethy phthalate,DMP）为目标物,研究其光电催化降解反应动力学和光电协同作用。结果显示：DMP的降解符合拟一级动力学规律;当DMP初始浓度一定时,影响DMP光电催化降解速率的因素由强到弱依次为：催化剂有效面积,紫外光强度,曝氧速率,外加偏转电压等。实验证明本体系中光电之间具有协同作用。     

碳纳米管/二氧化钛/壳聚糖催化薄膜光催化活性及苯降解机理

通过X-射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外可见光漫反射谱(UV-vis)对碳纳米管/二氧化钛/壳聚糖复合薄膜的晶体结构和形貌进行表征,以室内空气典型污染物气相苯为模型反应物,研究碳纳米管/二氧化钛/壳聚糖催化薄膜的光催化活性及其对苯的光降解机理。结果表明,制备的碳纳米管/二氧化钛/壳聚糖催化薄膜所具有的良好催化活性归功于碳纳米管、二氧化钛和壳聚糖三者的协调效应;气相苯光降解产生的主要中间产物是乙酸乙酯和十一烷,以及少量的丙烯醛、4-羰基-甲基-苯乙酮、十二烷烃、2,4,-二叔丁基苯酚、二十一烷烃。根据红外光谱分析与GC/MS分析结果,进一步提出了气相苯的降解机理过程。     

Effect of particle size of titanium dioxide nanoparticle aggregates on the degradation of one azo dye

Introduction

Titanium dioxide (TiO₂) nanoparticle powders have been extensively studied to quickly photodegrade some organic pollutants; however, the effect of the particle size of TiO₂ nanoparticle aggregates on degradation remains unclear because microscale aggregates form once the nanoparticle powders enter into water.

Methods

The degradation of azo dye by different particle sizes of TiO₂ nanoparticle aggregates controlled by NaCl concentrations was investigated to evaluate the particle size effect. Removal reactions of reactive black 5 (RB5) with TiO₂ nanoparticles followed pseudo-first-order kinetics.

Results

The increase of TiO₂ dosage from 40 to 70?mg/L enhanced the degradation. At doses around 100?mg/L TiO₂, degradation rates decreased which could be the result of poor UV light transmittance at high-particle concentrations. At average particle sizes of TiO₂ nanopowders less than around 500?nm, the degradation rates increased with decreasing particle size. As the average particle size exceeded 500?nm, the degradation rates were not significantly changed.

Conclusions

For the complete degradation experiments, the mineralization rates of total organic carbon disappearance are generally following the RB5 decolorization kinetic trend. These findings can facilitate the application of TiO₂ nanoparticles to the design of photodegradation treatments for wastewater.     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

Photoelectrocatalytic degradation of pentachlorophenol in aqueous solution using a TiO2 nanotube film electrode

Titanium dioxide (TiO2) nanotube film electrodes are fabricated by the anodic oxidation method. Scanning electron microscopy (SEM) showed that these tubes were well aligned and organized into high-density uniform arrays. XRD analysis showed the TiO2 nanotubes to be in the anatase crystal form. The TiO2 nanotube film electrode exhibited increased photoelectrocatalytic (PEC) capability compared to a traditional TiO2 film electrode fabricated using the anodizing method for pentachlorophenol (PCP) degradation in aqueous solution. The bias potential, pH value, and electrolyte concentration were shown to be important factors influencing the degradation of PCP by the PEC method using the TiO2 nanotube film electrode as the working electrode.     

TiO2膜降解水中污染物的稳定性考察与再生方法研究

针对实际水处理中对催化剂性能的要求，以光催化降解苯酚溶液作为探针反应，考察了玻璃纤维网上负载的TiO₂膜催化剂长期使用条件下的稳定性，研究了催化剂在自来水中使用失活后的再生方法。结果表明，经过50次使用之后，膜催化剂120 min反应对苯酚的降解率从100%下降至83%，总体上看，所制催化剂还是具有相当好的稳定性；在反应器中用蒸馏水浸泡配合光催化反应对TiO₂膜催化剂进行原位再生是一种可行的再生途径。     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

电化学催化降解水中有机污染物的研究进展

电化学法催化降解废水中的有机污染物已引起广泛兴趣。在电极的作用下 ,电化学反应和化学催化作用结合 ,可导致有机分子的电催化降解。选用合适的电极材料可以加速电化学反应速率 ,有助于有机物的电化学转化。本文讨论了提高电催化降解速率的方法 ,指出了在该领域的研究中存在的问题和发展方向     

Ozone facilitated degradation of caffeine using Ce-TiO2 catalyst

The ozone initiated oxidation of 1,3,7-trimethylxanthine (caffeine), commonly found in wastewaters as model compound is reported using cerium (Ce)/titanium dioxide (TiO₂) as catalyst. The effect of pH and loading of ceria on titania were investigated. Effect of reaction conditions on degradation of caffeine based on their pseudo first-order rate constants were compared. The combination of catalyst Ce-TiO₂ and ozone aeration significantly enhanced the degradation of caffeine compared to uncatalysed ozonation. The oxidation of caffeine ensued via the free radical mechanism, through enhanced ozone decomposition into OH radicals. Ce/TiO₂(0.5?wt%) showed good activity in degradation of caffeine at pH 6, in both natural stream and river water samples showing about 60% total organic carbon removal in 2?h ozonation period. Using liquid chromatography-mass spectroscopy, degradation products were analysed. A reaction intermediate and one final product were positively identified. Nano-catalysts with different loadings of Ce on TiO₂ synthesized by sol-gel route were characterized by scanning electron microscope, transmission electron microscopy, BET and powder X-ray diffraction spectrum techniques. The results showed that the material retained a highly ordered mesoporous structure and possessed large surface area.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

Photocatalytic degradation of the herbicide chloridazon on mesoporous titania/zirconia nanopowders

Advanced oxidation processes using semiconducting photocatalysts for the degradation of organic pollutants are a promising approach for the remediation of pesticide-contaminated wastewater. High photodegradation efficiency and stability of the photocatalyst are of key importance for practical application of the semiconductor. In this study, mesoporous TiO₂/ZrO₂ nanopowders were synthesized via two techniques; evaporation-induced self-assembly (EISA) and sol-gel using triblock copolymers Pluronic P123 and F127. The photodegradation activities of the composites were determined by employing the herbicide chloridazon as a model compound. Due to well-developed mesoporosity, the TiO₂/ZrO₂ nanocomposite synthesized by EISA displays high surface area and small crystallite sizes leading to higher photocatalytic activity than pristine TiO₂ prepared under similar condition and commercial Degussa P25 nanopowder. The optimum amount of zirconium required for the highest activities was identified and found to be 0.14 and 0.05 mol% for the EISA and sol-gel-prepared samples, respectively. Systematic studies of the post-thermal treatment step for both samples show that Zr inhibits an anatase-to-rutile phase transition only up to 600 °C, at higher temperature phase separation occurs. Samples synthesized by EISA method showed enhanced degradation activity than sol-gel-synthesized samples.     

Solar light–driven photocatalytic degradation and mineralization of beta blockers propranolol and atenolol by carbon dot/TiO2 composite

Herein improved solar light–driven photocatalytic degradation and mineralization of two emerging pollutants as well as recalcitrant beta blockers propranolol (PR) and atenolol (AT) have been demonstrated by metal-free carbon dot/TiO₂ (CDT) composite. Hydrothermally synthesized TiO₂ has been decorated with electrochemically synthesized carbon dots (CDs) and was well characterized by various analytical techniques viz. XRD, FTIR, Raman, XPS, UV–visible DRS, FESEM, and TEM. The optimized CDT composite, 2CDT (2 mL carbon dot/TiO₂), showed?~?3.45- and?~?1.75-fold enhancement in the photodegradation rate as compared to pristine TiO₂ for PR and AT respectively in 1 hour of irradiation along with complete degradation of PR and AT after 3 hours of irradiation. 2CDT exhibited 76% and 80% mineralization of PR and AT in contrast with 62% and 47% observed by pristine TiO₂. Further, the major reaction intermediates formed after degradation have been identified by HPLC/MS analysis, confirming more than 99% reduction of the parent compound for both PR and AT. Reusability of the optimized catalyst also showed successful degradation up to 3 cycles, showing reduction abilities of 97%, 95%, and 94% for 1st, 2nd, and 3rd cycle respectively. The enhanced degradation and mineralization efficiency of the 2CDT composite could be attributed to the excellent photosensitizer and electron reservoir properties of the CD along with upconverted photoluminescence behavior. The present study unlocks the possibility of using metal-free, facile CDT composite for effective degradation and mineralization of widely used beta blockers and other pharmaceuticals.

     

Emerging trends in photodegradation of petrochemical wastes: a review

Various human activities like mining and extraction of mineral oils have been used for the modernization of society and well-beings. However, the by-products such as petrochemical wastes generated from such industries are carcinogenic and toxic, which had increased environmental pollution and risks to human health several folds. Various methods such as physical, chemical and biological methods have been used to degrade these pollutants from wastewater. Advance oxidation processes (AOPs) are evolving techniques for efficient sequestration of chemically stable and less biodegradable organic pollutants. In the present review, photocatalytic degradation of petrochemical wastes containing monoaromatic and poly-aromatic hydrocarbons has been studied using various heterogeneous photocatalysts (such as TiO₂, ZnO and CdS. The present article seeks to offer a scientific and technical overview of the current trend in the use of the photocatalyst for remediation and degradation of petrochemical waste depending upon the recent advances in photodegradation of petrochemical research using bibliometric analysis. We further outlined the effect of various heterogeneous catalysts and their ecotoxicity, various degradation pathways of petrochemical wastes, the key regulatory parameters and the reactors used. A critical analysis of the available literature revealed that TiO₂ is widely reported in the degradation processes along with other semiconductors/nanomaterials in visible and UV light irradiation. Further, various degradation studies have been carried out at laboratory scale in the presence of UV light. However, further elaborative research is needed for successful application of the laboratory scale techniques to pilot-scale operation and to develop environmental friendly catalysts which support the sustainable treatment technology with the “zero concept” of industrial wastewater. Nevertheless, there is a need to develop more effective methods which consume less energy and are more efficient in pilot scale for the demineralization of pollutant.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

Photocatalytic degradation of gaseous toluene over Ag-doping TiO₂ nanotube powder prepared by anodization coupled with impregnation method

In this work, Ag-doping TiO₂ nanotubes were prepared and employed as the photocatalyst for the degradation of toluene. The TiO₂ nanotube powder was produced by the rapid-breakdown potentiostatic anodization of Ti foil in chloride-containing electrolytes, and then doped with Ag through an incipient wetness impregnation method. The samples were characterized by scanning electron microscope, high-resolution transmission electron microscopy, X-ray diffraction, surface photovoltage measurements, X-ray photoelectron spectroscopy and N₂ adsorption. The nanotubular TiO₂ photocatalysts showed an outer diameter of approximately 40 nm, fine mesoporous structure and high specific surface area. The photocatalytic activity of Ag-doping TiO₂ nanotube powder was evaluated through photooxidation of gaseous toluene. The results indicated that the degradation efficiency of toluene could get 98% after 4 h reaction using the Ag-doping TiO₂ nanotubes as the photocatalyst under UV light illumination, which was higher than that of the pure TiO₂ nanotubes, Ag-doping P25 or P25. Benzaldehyde species could be observed during the photocatalytic oxidation monitored by in situ FTIR, and the formed benzaldehyde intermediate during reaction would be partially oxidized into CO₂ and H₂O.