Pesticide residues in air from coastal environment, south India.

Chlorinated pollutants are transported through atmosphere. India is one of the point source countries for these pollutants [1]. In this study the concentration of DDT and HCH were evaluated in air from a tropical coastal environmental (at Parangipettai--southeast coast of India). DDT and HCH ranged in concentrations from 0.16 to 5.93 ng m-3 and 1.45 to 35.6 ng m-3 respectively. The ban on DDT in agriculture is reflected from the low residue levels recorded, predominantly by metabolites other than the parent compounds.     

MTBE and aromatic hydrocarbons in North Carolina stormwater runoff

A total of 249 stormwater samples were collected from 46 different sampling locations in North Carolina over an approximate 1-year period and analyzed to identify land use types where fuel oxygenates and aromatic hydrocarbons may be present in higher concentrations and at greater frequency. Samples were analyzed by gas chromatography-mass spectrometry in ion selective mode to achieve a quantitation limit of 0.05 microg/l. m-,p-Xylene and toluene were detected in over half of all samples analyzed, followed by MTBE: o-xylene: 1,3,5-trimethylbenzene: ethylbenzene; and 1,2,4-trimethylbenzene. Benzene, DIPE, TAME and 1,2,3-trimethylbenzene were detected in < 10% of the samples analyzed. Median contaminant concentrations (when detected) varied from 0.07 microg/l for ethylbenzene to 0.11 microg/l for toluene. All of the locations with significantly higher contaminant concentrations were associated with direct runoff from a gas station or discharge of contaminated groundwater from a former leaking underground storage tank. For all of the aromatic hydrocarbons, the maximum observed contaminant concentrations were over an order of magnitude lower than current drinking water standards.     

Characterizing relationships between personal exposures to VOCs and socioeconomic,demographic, behavioral variables

Socioeconomic and demographic factors have been found to significantly affect time-activity patterns in population cohorts that can subsequently influence personal exposures to air pollutants. This study investigates relationships between personal exposures to eight VOCs (benzene, toluene, ethylbenzene, o-xylene, m-,p-xylene, chloroform, 1,4-dichlorobenzene, and tetrachloroethene) and socioeconomic, demographic, time-activity pattern factors using data collected from the 1999–2000 National Health and Nutrition Examination Survey (NHANES) VOC study. Socio-demographic factors (such as race/ethnicity and family income) were generally found to significantly influence personal exposures to the three chlorinated compounds. This was mainly due to the associations paired by race/ethnicity and urban residence, race/ethnicity and use of air freshener in car, family income and use of dry-cleaner, which can in turn affect exposures to chloroform, 1,4-dichlorobenzene, and tetrachloroethene, respectively. For BTEX, the traffic-related compounds, housing characteristics (leaving home windows open and having an attached garage) and personal activities related to the uses of fuels or solvent-related products played more significant roles in influencing exposures. Significant differences in BTEX exposures were also commonly found in relation to gender, due to associated significant differences in time spent at work/school and outdoors. The coupling of Classification and Regression Tree (CART) and Bootstrap Aggregating (Bagging) techniques were used as effective tools for characterizing robust sets of significant VOC exposure factors presented above, which conventional statistical approaches could not accomplish. Identification of these significant VOC exposure factors can be used to generate hypotheses for future investigations about possible significant VOC exposure sources and pathways in the general U.S. population.     

Time-resolved measurements of PM2.5 carbonaceous aerosols at Gosan, Korea

In order to better understand the characteristics of atmospheric carbonaceous aerosol at a background site in Northeast Asia, semicontinuous organic carbon (OC) and elemental carbon (EC), and time-resolved water-soluble organic carbon (WSOC) were measured by a Sunset OC/ EC and a PILS-TOC (particle-into-liquid sampler coupled with an online total organic carbon) analyzer, respectively, at the Gosan supersite on Jeju Island, Korea, in the summer (May 28-June 17) and fall (August 24-September 30) of 2009. Hourly average OC concentration varied in the range of approximately 0.87-28.38 microgC m-3, with a mean of 4.07+/- 2.60 microgC m-3, while the hourly average EC concentration ranged approximately from 0.04 to 8.19 .microgC m-3, with a mean of 1.35 +/- 0.71 microgC m-3, from May 28 to June 17, 2009. During the fall season, OC varied in the approximate range 0.9-9.6 microgC m-3, with a mean of 2.30 +/-0.80 microgC m-3, whereas EC ranged approximately from 0.01 to 5.40 microgC m-3, with a mean of 0.66 +/- 0.38 microgC m-3. Average contributions of EC to TC and WSOC to OC were 26.0% +/- 9.7% and 20.6% +/-7.4%, and 37.6% +/- 23.5% and 57.2% +/- 22.2% during summer and fall seasons, respectively. As expected, clear diurnal variation of WSOC/OC was found in summer, varying from 0.22 during the nighttime up to 0.72 during the daytime, mainly due to the photo-oxidation process. In order to investigate the effect of air mass pathway on the characteristics of carbonaceous aerosol, 5-day back-trajectory analysis was conducted using the HYSPLIT model. The air mass pathways were classified into four types: Continental (CC), Marine (M), East Sea (ES) and Korean Peninsula (KP). The highest OC/EC ratio of 3.63 was observed when air mass originated from the Continental area (CC). The lowest OC/EC ratio of 0.79 was measured when air mass originated from the Marine area (M). A high OC concentration was occasionally observed at Gosan due to local biomass burning activities. The contribution of secondary OC to total OC varied approximately between 8.4% and 32.2% and depended on air mass type.     

Characterization of emissions during the heating of tyre contaminated scrap

In order to characterize the compounds (type and quantities) emitted during melting of organic contaminated scrap and to investigate the mechanism of their formation, an experimental set-up has been designed and built to study precisely the influence of temperature and gas atmosphere in the conditions of an electric arc furnace. These experiments lead to the determination of mass balances (C, H, O, S) and to the quantification of unburnt compounds (tars, carbon monoxide, volatile organic compounds (VOCs), benzene, toluene, ethylbenzene and xylenes (BTEX), polyaromatic compounds (PAHs)). Degradation conditions (gas atmosphere and temperature) corresponding to different areas in the electric furnace have also been investigated. Such experiments lead to a better understanding of degradation mechanisms; this interpretation is not possible from investigations performed in an industrial furnace since there are many uncontrolled parameters (large dispersion of the results).     

Commuter exposures to VOCs in Boston, Massachusetts.

This study examines the commuter's exposure to six gasoline-related volatile organic compounds (VOCs): benzene, toluene, ethylbenzene, m-/p-xylene, o-xylene, and formaldehyde. The VOC concentrations to which commuters were exposed in four different commuting modes (driving, subway, walking, and biking) in Boston, Massachusetts, are compared. The VOC concentrations in participants' homes and offices were also measured. Factors that could influence in-vehicle VOC concentrations, such as different traffic patterns, car model and vehicle ventilation conditions, were also evaluated. Driving a private car was associated with higher VOC concentrations and commuting on urban roadways resulted in the highest VOC concentrations. The use of car heaters resulted in higher in-vehicle VOC concentrations. The longer the subway commuters stayed underground, the higher their VOC exposures. The home-to-work car or subway commute represented about 10 to 20 percent of an individual's total VOC exposure for these compounds.     

管式生物过滤器去除乙苯废气

生物过滤由于其良好的成本效益和环境友好性已经成为控制挥发性有机化合物(VOCs)含量和气味气体排放的常规技术。营养物质的均匀分布、生物膜和介质床内的气体流是成就一个性能优良的生物过滤器至关重要的因素。而由本实验室开发的管式生物过滤器(TBFs)已被证明具备此优势。本实验的管式生物过滤器以聚氨酯海绵作为填料,研究在不同有机负荷、气体停留时间(EBCT)、进气量和表面活性剂等条件下乙苯废气的去除效率(RE)。实验同时记录了管式生物过滤器启动阶段的表现。初期使附着在填料上的微生物暴露在浓度为40 mg/m3的乙苯废气中40 d,此时的气体停留时间为15 s,使微生物慢慢适应并逐步降解乙苯废气;然后连续地控制管式生物过滤器的入口乙苯浓度为40、80、120和160 mg/m3,以使有机负荷逐步升高。结果表明,乙苯去除效率随着有机负荷的增大而逐步减小。当气体停留时间从15 s增加到30 s和60 s,而有机负荷控制在38.60 g/(m3·h)时,乙苯废气去除效率略微增加。此外,随着进气量的增大乙苯废气的最大平均去除效率有所下降而此时的降解容量增大,这个过程中乙苯进气浓度保持不变。结果还表明,在营养液中加入聚乙二醇辛基苯基醚这种表面活性剂可以提高乙苯废气的去除效率。     

Measurement of BTEX (benzene,toluene, ethybenzene,and xylene) levels at urban and semirural areas of Algiers City using passive air samplers

The study presents the levels of air pollution by aromatic organic compounds BTEX (benzene, toluene, ethylbenzene, o-, m-, and p-xylenes) in the city of Algiers. The sampling was carried out using Radiello passive sampler. Three sampling campaigns were carried out in roadside, tunnel, urban background, and semirural sites in Algiers. In order to determine the diurnal mean levels of air pollution by BTEX to which people are exposed, a modified passive sampler was used for the first time. In addition, monitoring of pollution inside vehicles was also made. In the spring of 2009, more than 27 samplings were carried out. In the background and road traffic sites the Radiello sampler was exposed for 7 days, whereas the time exposure was reduced to 1 day in the case of the vehicle as well as the tunnel. The results indicate that average benzene concentrations in the roadside and inside vehicle exceed largely the limit value of 5 μg m^?3 established by the European Community (EC). On the other hand, it has been noticed that the concentration levels of other BTEX are relatively high. Also, in order to identify the origin of emission sources, ratios and correlations between the BTEX species have been highlighted. This study shows that road traffic remains the main source of many local emission in Algiers.

Implications The vehicle fleet in Algeria is growing rapidly since the 1990s following economic growth and is responsible for the increasing air pollution in large cities. Because there are no data collection of BTEX carried out by national air quality network, all environmental and transportation policies are based on European emissions standards, but national emission standards are currently not in place. This work will contribute to the analysis of real emissions of BTEX in Algiers, for the development of management and for assessment of population exposure variation depending on the location in the city of Algiers.     

A method for determination of methyl chloride concentration in air trapped in ice cores

A method for measuring the concentration of methyl chloride (CH3Cl) in air trapped in an ice core was developed. The method combines the air extraction by milling the ice core samples under vacuum and the analysis of the extracted air with a cryogenic preconcentration/gas chromatograph/mass spectrometry system. The method was applied to air from Antarctic ice core samples estimated to have been formed in the pre-industrial and/or early industrial periods. The overall precision of the method deduced from duplicate ice core analyses was estimated to be better than +/-20 pptv. The measured CH3Cl concentration of 528+/-26 pptv was similar to the present-day concentration in the remote atmosphere as well as the CH3Cl concentration over the past 300 years obtained from Antarctic firn air and ice core analyses.     

Soiling Potential—A New Method for Measuring Smoke Emission

There is a growing interest in effects of sub-micron, nonsettling particles in the atmosphere among air pollution control agencies throughout the country. This type of pollution, generally referred to as the “soiling index” of the atmosphere, is produced primarily by the incomplete combustion of fuels. The measurement procedure has been fairly well standardized, the values being reported as Cohs or Ruds per 1000 linear feet of air. Using a similar technique, a method of quantitating smoke emission in objective terms first demonstrated by W. C. L. Hemeon in 1953, has been applied to source testing at several operating plants by the Cincinnati Division of Air Pollution Control. The source strength will be called “soiling potential” while the effect in the general atmosphere is termed “soiling index.” The soiling potential unit is Rud-ft² per cubic foot exhaust gases or Rud-ft² per unit of fuel input. The “Soiling Potential” sampler is described and results of tests are given. Included is the use of soiling potential in quantitating smoke emission from single sources and for constructing area wide inventory of smoke emission. The use of an area wide smoke emission inventory in Rudft2 in a simple diffusion model for calculating the soiling index (Rud-ft²/1000 cu ft) in the general atmosphere at a given point is explored.     

Changes in concentration levels of selected VOCs in newly erected and remodelled building in Gdansk

Volatile organic compounds such as benzene, toluene, butyl acetate, ethylbenzene, m-xylene, styrene and m-dichlorobenzene were measured in three newly erected and remodelled dwellings. The present study also attempted to examine the time dependence of concentrations of selected VOCs in each investigated dwelling. This was accomplished by at least triplicate measurements of the IAQ. To collect a series of air samples the active and passive methods were used. In both cases activated charcoal was applied as a sorption medium. The samples were recovered by solvent extraction, and analysed by capillary column gas chromatography, employing a flame ionisation detector. The experimental results showed that MAC values for analysed VOCs were exceeded (even a few orders of magnitude) for the measurements made before inhabiting of the occupants, in every investigated dwelling. The concentrations of the investigated VOCs decreased significantly with time, which should be expected, although in some cases the levels of selected VOCs remained still high. Our experience indicates that parallel application of two different indoor air sampling techniques to determine analytes of interest, though more laborious and time consuming, can lead to significant conclusions concerning indoor air quality in monitored spaces.     

The seasonal changes in the concentration of polycyclic aromatic hydrocarbons in precipitation and aerosol near Lake Balaton, Hungary.

The concentration of polycyclic aromatic hydrocarbons (PAHs) in atmospheric precipitation and aerosol samples was monitored in a rural site by Lake Balaton, Hungary to examine the seasonal variation. The seasonal mean concentration of individual 3-6-ring PAHs in precipitation varied from 1 to 54 ng l-1 and from 3 to 350 ng l-1 in summer and winter, respectively. In the atmospheric aerosol samples the seasonal mean concentration of PAHs varied from 4 to 880 pg m-3, from 4 to 300 pg m-3, from 11 to 1050 pg m-3 and from 36 to 5000 pg m-3 in spring, summer, autumn and winter, respectively. Wet (412 micrograms m-2 year-1) and aerosol (190-300 micrograms m2 year-1) deposition rates were also estimated indicating that the two processes are of comparable importance in the removal of 3-6-ring PAHs from the atmosphere.     

A comparison of PAMS and air toxics measurements

One of the requirements of the 1990 Clean Air Act Amendments (CAA) is that 1-h ozone nonattainment areas that are classified severe or higher category are required to operate a network of photochemical assessment monitors (PAMS) to provide hourly measurements of volatile organic compounds (VOCs) comprising of Carbon number <12 (C2–C12), along with carbonyl measurements at 3-h intervals during the summer ozone season. Often collocated with PAMS are 24-h-integrated canister and cartridge-based measurements of selected air toxic compounds, thereby providing an opportunity for inter-comparison and validation of both sets of data. In this study, we report such a comparison and estimates of trend for benzene, m-, p- and o-xylene, toluene, ethylbenzene, 1,2,4-trimethylbenzene, formaldehyde and acetaldehyde at Bronx, NY. The analysis shows that hourly PAMS and 24-h-integrated air toxics are in good agreement with each other exhibiting similar trends and that the PAMS with the higher temporal resolution offers information on excursions of the toxic compounds that would be quite useful in assessment of acute health effects. These findings were also found to be applicable to other locations such as South De Kalb, GA; Gary, IN and Lynn, MA.     

National review of ambient air toxics observations

Ambient air observations of hazardous air pollutant (HAPs), also known as air toxics, derived from routine monitoring networks operated by states, local agencies, and tribes (SLTs), are analyzed to characterize national concentrations and risk across the nation for a representative subset of the 187 designated HAPs. Observations from the National Air Toxics Trend Sites (NATTS) network of 27 stations located in most major urban areas of the contiguous United States have provided a consistent record of HAPs that have been identified as posing the greatest risk since 2003 and have also captured similar concentration patterns of nearly 300 sites operated by SLTs. Relatively high concentration volatile organic compounds (VOCs) such as benzene, formaldehyde, and toluene exhibit the highest annual average concentration levels, typically ranging from 1 to 5 µg/m³. Halogenated (except for methylene chloride) and semivolatile organic compounds (SVOCs) and metals exhibit concentrations typically 2–3 orders of magnitude lower. Formaldehyde is the highest national risk driver based on estimated cancer risk and, nationally, has not exhibited significant changes in concentration, likely associated with the large pool of natural isoprene and formaldehyde emissions. Benzene, toluene, ethylbenzene, and 1,3-butadiene are ubiquitous VOC HAPs with large mobile source contributions that continue to exhibit declining concentrations over the last decade. Common chlorinated organic compounds such as ethylene dichloride and methylene chloride exhibit increasing concentrations. The variety of physical and chemical attributes and measurement technologies across 187 HAPs result in a broad range of method detection limits (MDLs) and cancer risk thresholds that challenge confidence in risk results for low concentration HAPs with MDLs near or greater than risk thresholds. From a national monitoring network perspective, the ability of the HAPs observational database to characterize the multiple pollutant and spatial scale patterns influencing exposure is severely limited and positioned to benefit by leveraging a variety of emerging measurement technologies.

Implications:?Ambient air toxics observation networks have limited ability to characterize the broad suite of hazardous air pollutants (HAPs) that affect exposures across multiple spatial scales. While our networks are best suited to capture major urban-scale signals of ubiquitous volatile organic compound HAPs, incorporation of sensing technologies that address regional and local-scale exposures should be pursued to address major gaps in spatial resolution. Caution should be exercised in interpreting HAPs observations based on data proximity to minimum detection limit and risk thresholds.     

Concentration and trend of 9,10-phenanthrenequinone in airborne particulates collected in Nagasaki city, Japan

9,10-Phenanthrenequinone (PQ), one of the components of atmospheric pollutants, has potent harmful effects on human health. PQ in airborne particulates collected in Nagasaki city was determined by HPLC with fluorescence derivatization. PQ extracted from airborne particulates using methanol was derivatized with benzaldehyde in the presence of ammonium acetate to give a fluorescent compound. The average concentration (mean+/-SD, n=52) of PQ found in airborne particulates collected from July 1997 to June 1998 was 0.287+/-0.128 ng m-3. Concentrations of PQ in winter were higher than those in summer. In a weekly variation study, PQ concentrations were higher during weekdays and lower at weekend. The levels of PQ were obviously correlated with those of phenanthrene (PH) that is considered as a parent compound of PQ. This observation suggested that PQ was emitted into the atmosphere from the same source as PH, or PQ was converted from PH in the atmosphere.     

Carbonyl atmospheric reaction products of aromatic hydrocarbons in ambient air

To convert gaseous carbonyls to oximes during sampling, an XAD-4 resin denuder system pre-coated with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine and followed by analysis with methane positive chemical ionization gas chromatography/mass spectrometry was used to measure carbonyls in ambient air samples in Riverside, CA. In conjunction with similar analyses of environmental chamber OH radical-initiated reactions of o- and p-xylene, 1,2,4-trimethylbenzene, ethylbenzene, 4-hydroxy-2-butanone and 1,4-butanediol, we identified benzaldehyde, o-, m- and p-tolualdehyde and acetophenone and the dicarbonyls glyoxal, methylglyoxal, biacetyl, ethylglyoxal, 1,4-butenedial, 3-hexene-2,5-dione, 3-oxo-butanal, 1,4-butanedial and malonaldehyde in the ambient air samples. As discussed, these carbonyls and dicarbonyls can be formed from the OH radical-initiated reactions of aromatic hydrocarbons and other volatile organic compounds emitted into the atmosphere, and we conclude that in situ atmospheric formation is a major source of these carbonyls in our Riverside, CA, ambient air samples.     

Determination of benzene, toluene, ethylbenzene, xylenes in water at sub-ng l-1 levels by solid-phase microextraction coupled to cryo-trap gas chromatography-mass spectrometry

A trace analytical method of benzene, toluene, ethylbenzene and xylenes (BTEX) in water has been developed by using headspace solid-phase microextraction (HS-SPME) coupled to cryo-trap gas chromatography-mass spectrometry (GC-MS). The chromatographic peak shape for BTEX was improved by using cryo-trap equipment. The HS-SPME experimental procedures to extract BTEX from water were optimized with a 75 microm carboxen/polydimethylsiloxane (CAR/PDMS)-coated fiber at a sodium chloride concentration of 267 g l(-1), extraction for 15 min at 25 degrees C and desorption at 290 degrees C for 2 min. Good linearity was verified in a range of 0.0001-50 microg l(-1) for each analyte (r(2)=0.996-0.999). The limits of detection (LODs) of BTEX in water reached at sub-ng l(-1) levels. LODs of benzene, toluene, ethylbenzene, m/p-xylene and o-xylene were 0.04, 0.02, 0.05, 0.01 and 0.02 ng l(-1), respectively. The proposed analytical method was successfully used for the quantification of trace BTEX in ground water. The results indicate that HS-SPME coupled to cryo-trap GC-MS is an effective tool for analysis of BTEX in water samples at the sub-ng l(-1) level.     

A 3D aerosol and visibility information system for urban areas using remote sensing and GIS

Currently, the depiction of urban air quality at boundary layer scale uses modelled climatic and land cover data. However, such models are difficult to verify, and only low to moderate accuracy may be achieved due to the complexity of the input data required and the reliance on assumptions about dispersion patterns. The provision of comprehensive air quality data to urban residents in city districts, at a level of detail commensurate with other Location-Based Services (LBS) which are time- and place-sensitive, has therefore not been possible. A method for urban air quality monitoring over cities at boundary layer scale, other than by the use of air quality models is presented here. The system presented uses empirical Aerosol Optical Thickness (AOT) data in near-real time, combining AOT data from AERONET with aerosol vertical profiles computed from twice-daily MODIS satellite images at 500 m resolution, to give three dimensional (3D) air quality data over the urban landscape. There has been no previous attempt to project the horizontal spatial distribution of aerosols from satellite image pixels into a vertical dimension to give a spatially comprehensive three dimensional record of air quality. The paper describes the sources and accuracy of the AOT data input to the system as well as its storage and retrieval on a Geographic Information System (GIS) platform, to provide air quality and visibility information according to user query at any 3D geographical location, including individual buildings or building floor.     

Organic compound emissions from a landfarm used for oil and gas solid waste disposal

Solid or sludgy hydrocarbon waste is a by-product of oil and gas exploration and production. One commonly used method of disposing of this waste is landfarming. Landfarming involves spreading hydrocarbon waste on soils, tilling it into the soil, and allowing it to biodegrade. We used a dynamic flux chamber to measure fluxes of methane, a suite of 54 nonmethane hydrocarbons, and light alcohols from an active and a remediated landfarm in eastern Utah. Fluxes from the remediated landfarm were not different from a polytetrafluoroethylene (PTFE) sheet or from undisturbed soils in the region. Fluxes of methane, total nonmethane hydrocarbons, and alcohols from the landfarm in active use were 1.41 (0.37, 4.19) (mean and 95% confidence limits), 197.90 (114.72, 370.46), and 4.17 (0.03, 15.89) mg m^?2 hr^?1, respectively. Hydrocarbon fluxes were dominated by alkanes, especially those with six or more carbons. A 2-ha landfarm with fluxes of the magnitude we observed in this study would emit 95.3 (54.3, 179.7) kg day^?1 of total hydrocarbons, including 11.2 (4.3, 33.9) kg day^?1 of BTEX (benzene, toluene, ethylbenzene, and xylenes).

Implications: Solid and sludgy hydrocarbon waste from the oil and gas industry is often disposed of by landfarming, in which wastes are tilled into soil and allowed to decompose. We show that a land farm in Utah emitted a variety of organic compounds into the atmosphere, including hazardous air pollutants and compounds that form ozone. We calculate that a 2-ha landfarm facility would emit 95.0 ± 66.0 kg day^?1 of total hydrocarbons, including 11.1 ± 1.5 kg day^?1 of BTEX (benzene, toluene, ethylbenzene, and xylenes).     

Monoaromatic compounds in ambient air of various cities: a focus on correlations between the xylenes and ethylbenzene

Speciation of o-xylene, m-xylene, p-xylene and ethylbenzene was performed by gas chromatography from ambient air and liquid fuel samples collected at various locations in 19 cities in Europe, Asia and South America. The xylene's mixing ratios were compared to each other from the various locations, which included urban air, traffic air and liquid fuel. For all samples, the xylenes exhibited robust correlations, and the slopes remained constant. The m-xylene/p-xylene ratio was found to be 2.33±0.30, and the m-xylene/o-xylene ratio was found to be 1.84±0.25. These ratios remain persistent even in biomass combustion experiments (in South America and South Africa). Comparing the xylenes to toluene and benzene indicate that combustion, but not fuel evaporation, is the major common source of the xylenes in areas dominated by automotive emissions. Although a wide range of combustion types and combustion efficiencies were encountered throughout all the locations investigated, xylenes and ethylbenzene ratios remained persistent. We discuss the implications of the constancies in the xylenes and ethylbenzene ratios on atmospheric chemistry.