Fractionation and elemental association of Zn, Cd and Pb in soils contaminated by Zn minings using a continuous-flow sequential extraction

Fractionation and elemental association of Zn, Cd, and Pb in soils near Zn mining areas were studied using a continuous-flow sequential extraction approach. The recently developed sequential extraction procedure not only gave fractional distribution data for evaluation of the mobility or potential environmental impact of the metals, but also the extraction profiles (extractograms) which were used for study of elemental association. In addition, the elemental atomic ratio plot extractogram can be used to demonstrate the degree of anthropogenic contamination. Seventy-nine soil samples were collected in the vicinity of a Zn mine and were fractionated into 4 phases i.e. exchangeable (F1), acid soluble (F2), reducible (F3) and oxidizable (F4) phases. Most samples were contaminated with Zn, Cd and Pb. The reducible phase is the most abundant fraction for Zn and Pb (>50%) while Cd is concentrated in the first 3 extraction steps. The distribution patterns of Cd were obviously affected by soil pH. 55% of Cd appears predominantly in the F1 fraction for acidic soils while in neutral and alkaline soils, it was mostly (70%) found in the F2 + F3 fractions. The extractograms obtained from the continuous-flow extraction system revealed close association between Zn, Cd, Pb and Fe in the acid soluble phase, Cd-Pb and Zn-Fe in the reducible phase for contaminated soils. A correlation study of the 3 metals using a correlation coefficient was also performed to compare the results with the elemental association revealed by the extractograms. Atomic ratio plot extractograms of Zn/Fe, Cd/Fe and Pb/Fe in the reducible phase, where contaminated metals are predominant, can be used to evaluate the degree of anthropogenic contamination. From the elemental atomic ratio plot, it is obvious that the contaminants Cd and Pb are mostly adsorbed on the surface of Fe oxides. Zn, which is present in an approximately 1 ratio 1 ratio with Fe in contaminated soils, does not show a similar trend to that found for Cd and Pb.     

Distribution and fractionation of cadmium, copper, lead, nickel, and zinc in a calcareous sandy soil receiving municipal solid waste

This study was conducted to evaluate the degree of mobility and fractionation of cadmium (Cd), copper (Cu), lead (Pb), nickel (Ni), and zinc (Zn) after the addition of municipal solid sewage sludge (MSS) in a sandy calcareous soil. Treatments were (1) soil application of MSS, (2) soil application of enriched municipal solid waste compost (EMSS), and (3) control soil. The MSS application represented a dose of 200 Mg dry weight per hectare. Soil columns were incubated at room temperature for 15 days and irrigated daily with deionized water to make a total of 505 mm. At the end of leaching experiments, soil samples from each column were divided into 14 layers, each being 1 cm down to 10 and 2.5 cm below that and analyzed for diethylenetriaminepentaacetic acid (DTPA)-extractable Cd, Cu, Pb, Ni, and Zn. The fractionation of the heavy metals in the top five layers of the surface soil samples was investigated by the sequential extraction method. All soil layers of the columns receiving MSS and EMSS had significantly higher concentrations of DTPA-extractable heavy metals than control soil. The maximum concentration of heavy metals in treated soil was in the surface layer and declined significantly with depth. Sequential extraction results showed that in the treated soil, a major proportion of Cd, Pb, and Ni was associated with organic matter (OM) and exchangeable (EXCH) fractions, and a major proportion of Cu and Zn was associated with residual (RES) and OM fractions. Based on relative percent, Pb, Cd, and Ni in the EXCH fraction was higher than Cu and Zn in soil leached with MSS and EMSS, suggesting that application of this MSS to a sandy calcareous soil, at the loading rate used here, may pose a risk in terms of groundwater contamination with Pb, Cd, and Ni.     

Pollution, fractionation, and mobility of Pb, Cd, Cu, and Zn in garden and paddy soils from a Pb/Zn mining area

This study was conducted to investigate the pollution load index, fraction distributions, and mobility of Pb, Cd, Cu, and Zn in garden and paddy soils collected from a Pb/Zn mine in Chenzhou City, China. The samples were analyzed using Leleyter and Probst’s sequential extraction procedures. Total metal concentrations including Pb, Cd, Cu, and Zn exceeded the maximum permissible limits for soils set by the Ministry of Environmental Protection of China, and the order of the pollution index was Cd > Zn > Pb > Cu, indicating that the soils from both sites seriously suffered from heavy metal pollution, especially Cd. The sums of metal fractions were in agreement with the total contents of heavy metals. However, there were significant differences in fraction distributions of heavy metals in garden and paddy soils. The residual fractions of heavy metals were the predominant form with 43.0% for Pb, 32.3% for Cd, 33.5% for Cu, and 44.2% for Zn in garden soil, while 51.6% for Pb, 40.4% for Cd, 40.3% for Cu, and 40.9% for Zn in paddy soil. Furthermore, the proportions of water-soluble and exchangeable fractions extracted by the selected analytical methods were the lowest among all fractions. On the basis of the speciation of heavy metals, the mobility factor values of heavy metals have the following order: Cd (25.2–19.8%) > Cu (22.6–6.3%) > Zn (9.6–6.0%) > Pb (6.7–2.5%) in both contaminated soils.     

Mobility of selected trace elements in Mediterranean red soil amended with phosphogypsum: experimental study

Soil amendment by phosphogypsum (PG) application becomes of increasing importance in agriculture. This may lead, however, to soil, plant, and groundwater contamination with trace elements (TEs) inherently present in PG. Monitoring of selected TEs (Pb, Zn, Cu, and Cd) distribution and mobility in a Mediterranean red soil profile has been performed in soil parcels applied with PG over a 16-month period. Concentrations were measured in soil and plant samples collected from various depth intervals at different points in time. TEs sequential extraction was performed on soil and PG samples. Results showed soil profile enrichment peaked 5 months after PG application for Cd, and 12 months for Pb, Zn, and Cu. Rainwater, pH, total organic carbon, and cationic exchange capacity were the main controlling factors in TEs accumulation in soils. Cd was transferred to a soil depth of about 20 cm. Zn exhibited mobility towards deeper layers. Pb and Cu were accumulated in around 20-55-cm-deep layers. PG increased the solubility of the studied TEs; PG-applied soils contained TEs bound to exchangeable and acid-soluble fractions in higher percentages than reference soil. Pb, Zn, and Cu were sorbed into mineral soil phases, while Cd was mainly found in the exchangeable (bio-available) form. The order of TEs decreasing mobility was Zn > Cd > Pb > Cu. Roots and leaves of existed plants, Cichorium intybus L., accumulated high concentrations of Cd (1-2.4 mg/kg), exceeding recommended tolerable levels, and thus signifying potential health threats through contaminated crops. It was therefore recommended that PG should be applied in carefully established, monitored, and controlled quantities to agricultural soils.     

Pollution in the urban soils of Lianyungang,China, evaluated using a pollution index,mobility of heavy metals,and enzymatic activities

Soil samples from 16 urban sites in Lianyungang, China were collected and analyzed. A pollution index was used to assess the potential ecological risk of heavy metals and a sequential extraction procedure was used to evaluate the relative distribution of Cu, Zn, Pb, Cd, Cr, and As in exchangeable, carbonate, Fe/Mn oxide, organic/sulfide, and residual fractions. The mobility of heavy metals and urease (URE) activity, alkaline phosphatase (ALP) activity, and invertase (INV) activity of soils was determined. The results showed that the average concentrations of Cu, Zn, Pb, Cd, Cr, and As in Lianyungang soils were much higher than those in the coastal city soil background values of Jiangsu and China. Among the five studied regions (utilities, commercial, industrial, tourism, and roadside), the industrial region had the highest metal concentrations demonstrating that land use had a significant impact on the accumulation of heavy metals in Lianyungang soils. Compared to the other metals, Cd showed the highest ecological risk. According to chemical partitioning, Cu was associated with the organic/sulfides and Pb and Zn were mainly in the carbonate and the Fe/Mn oxide phase. The greatest amounts of Cd were found in exchangeable and carbonate fractions, while Cr and As were mainly in the residual fraction. Cd had the highest mobility of all metals, and the order of mobility (highest to lowest) of heavy metals in Lianyungang soils was Cd > Zn > Pb > Cu > As > Cr. Soil urease activity, alkaline phosphatase activity, and invertase activity varied considerably in different pollution degree sites. Soil enzyme activities had the lowest levels in roadside and industrial regions. Across all the soil data in the five regions, the total Cu, Zn, Pb, Cd, Cr, and As level was negatively correlated with urease activity, alkaline phosphatase activity, and invertase activity, but the relationship was not significant. In the industrial region, alkaline phosphatase activity had significant negative correlations with total Cu, Pb, Cr, Zn, Cd, and heavy metal fractions. This showed that alkaline phosphatase activity was sensitive to heavy metals in heavily contaminated regions, whereas urease and invertase were less affected. The combination of the various methods may offer a powerful analytical technique in the study of heavy metal pollution in street soil.     

Fractionation of eleven elements by chemical bonding from airborne particulate matter collected in an industrial city in Argentina

A four-step chemical sequential extraction procedure was used to evaluate the distribution of Al, As, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V and Zn in airborne particulate matter collected on glass fibre filters using a high-volume sampler. Two sets of samples were collected in 2001 (winter and summer campaigns) in representative zones of an industrial city of Argentina. The leaching scheme was applied to PM-10 particles and consisted in extracting the elements in four fractions, namely soluble and exchangeable elements; carbonates, oxides and reducible elements; bound to organic matter and sulfidic metals; and residual elements. Metals and metalloids at microg g(-1) level were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). Analyte concentration varied from 14 microg g(-1) (equivalent to 1.0 ng m(-3)) for As to 11.8 mg g(-1) (equivalent to 2,089 ng m(-3)) for Al. Seven elements, namely Al, Cr, Fe, Mn, Pb, Ti and Zn showed similar distributions in both seasons while As was distributed in a significantly different manner in each season. The results exhibited low As contents in the first and second fractions that could be associated with routine coal combustion and a high content in the third and fourth fractions of the summer samples that could be linked to the use of pesticides. Aluminium, As, Cu, Mn, Ni, Ti, V and Zn were found in different percentages in the more bioavailable aqueous fraction with As, Mn, V and Zn exhibiting solubilities greater than 1% while Cr and Pb being insoluble. The content of Al, Cr, Cu, Fe, Ni, Pb, and Zn in the residual fraction was, in average, higher than 50%. A comparative assessment of the use of the underlying information available from fractionation studies compared to that obtained from total element content was done for Fe and Mn. It showed that the results obtained using chemical sequential extraction procedures allowed further discrimination of the potential air pollution sources.     

Trace metal (Cd,Cu, Pb,Zn) fractionation in urban-industrial soils of Ust-Kamenogorsk (Oskemen), Kazakhstan—implications for the assessment of environmental quality

Ust-Kamenogorsk is one of the largest cities and industrial centers in Kazakhstan. Non-ferrous metallurgy (Zn–Pb smelter) has acted as a predominating industrial branch in the city since late 1940s. The industrial plants are situated directly adjacent to the residential area of the city which creates grievous ecotoxicological hazard. In the present paper, we aimed at assessing the trace metal pollution of top soils in Ust-Kamenogorsk and its potential threats to the local population. The top soils were sampled at 10 sites throughout the city center. We determined the physical and chemical properties of soils as well as the contents of Cd, Cu, Pb, and Zn. In addition, the soil samples were subjected to a five-step sequential extraction to ascertain the fractionation of trace metals. On this basis, we calculated the geoaccumulation index (I_geo) and pollution load index (PLI) and assessed bioavailability of the elements. From our data, it emerged that the soils displayed a strong polymetallic pollution. PLI was as high as 33.4. Throughout the city, the trace metal contents exceeded the geochemical background and allowable values for residential, recreational, and institutional areas. The I_geo obtained were 3.7–6.5 for Cd, 1.5–4.7 for Cu, 2.8–5.7 for Pb, and 2.6–4.6 for Zn. The soils in Ust-Kamenogorsk displayed extremely high contamination with Cd, moderate to strong contamination with Pb and Zn, and low to moderate contamination with Cu. Cd and Pb were found to be the most bioavailable elements. The mobility of trace metals in the soils changed in the order Cd > Pb > Zn > Cu.     

Trace metal speciation and contamination in an intertidal estuary

An analysis of the geochemical distribution of selected trace metals among various geochemical phases of the sediments in the Tees estuary was carried out using a sequential extraction technique and Differential Stripping Voltammetry. The sediments of the estuary are mainly organic rich clay silts and metal concentrations exceed those in the water column. Speciation results show that contamination of the estuary is mainly from anthropogenic sources. Pb and Zn are associated with the reducible, residual and oxidisable fractions. The speciation pattern of Cd was similar to those of lead and zinc. However there were also some exchangeable and bound to carbonate fractions although these were less significant. Cu is largely associated with the oxidisable and residual fractions, with insignificant bound to carbonate, exchangeable and reducible fractions. The most bioavailable forms of the metals are the free inorganic ions. Total metal concentrations in the estuary display a downward trend since the 1970s.     

Comparison of three sequential extraction procedures for partitioning of heavy metals in car park dusts

The aim of this study was to elucidate the amount of metal released at each step by using different extractants in three sequential extraction schemes for the partitioning of metal contents of car park deposited dust samples. For this purpose, three different sequential extraction procedures (SEP) were employed for the metal fractionation in car park dust samples collected from the campus of Erciyes University, Kayseri, Turkey. While two of the sequential extraction procedures contain five steps the other, namely the BCR sequential extraction scheme, has three steps. The first two methods fractionate metals to be exchangeable, bound to carbonates, bound to Mn oxides, bound to Fe oxides and bound to organic matter, and the BCR protocol fractionates the metals as acid soluble and exchangeable, reducible, and oxidisable. Determination of the metals Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn was performed by flame atomic absorption spectrometry (FAAS). The results obtained by the three methods were compared and showed that the amount of metal released at each step of the leaching procedure depended both on the type of reagents used and the sequence in which they were applied. The most mobile elements were Cd, Pb and Zn which are metals potentially toxic to the environment and are also known to originate from traffic. The calculated enrichment factors for Cd and Pb were substantially high (73.5-187 and 18.4-27.5, respectively) and somewhat lower for Zn (5.1-6.8). These results confirm that they are important metal pollutants for car parks. Detection limits and recoveries were found in the range of 0.01-1.39 microg ml(-1) and 68-126%, respectively, for the metals studied and the three sequential extraction procedures.     

Determination and speciation of heavy metals in sediments of the Juru River,Penang, Malaysia

The Juru River flows through largely urbanized areas and is grossly polluted by domestic wastes and discharges from pig farms. Other than carrying highly polluting organic materials, these wastes are also contaminated with heavy metals. To ascertain the extent of heavy metal pollution in the river, total and non-residual concentrations of Cu, Pb, Zn, Mn and Fe in sediment samples collected along the river were determined. The results indicate that both the total and non-residual metal concentrations in sediments can successfully be used to identify heavy metal pollution sources. The speciation of Zn, Mn and Fe in the sediment samples were investigated using a sequential leaching technique which identifies the elements among six operationally defined host fractions: (1) exchangeable, (2) carbonate and surface-associated, (3) easily reducible, (4) moderately reducible, (5) bound to organic matter and sulphides and (6) residual. The results indicate that Zn is mainly associated with the reducible fractions. Zn and Fe found in the moderately reducible fraction are significantly correlated, indicating that iron oxides is the preferred host phase by Zn.     

饶河入鄱阳湖口处沉积物中重金属分布特征及形态研究

为了解饶河入鄱阳湖湖口重金属污染状况,在鄱阳湖饶河入湖段设置了3个采样点,用原子吸收分光光度计对沉积物进行了重金属Cu、Pb、Zn的测定,分析了这3种元素在各采样点的形态分布特征.结果表明:饶河人鄱阳湖口处沉积物中Cu、Pb、Zn的污染较为严重,呈现出复合污染的趋势.该区域沉积物中3种元素的分布受水流的影响较大,其形态...     

Speciative distribution and bioavailability of metals in agricultural soils receiving industrial wastewater

In order to assess the metal pollution status of agricultural lands of Mandi Bahauuddin receiving industrial wastewater, 35 top soil samples were investigated for the determination of selected metal levels, i.e., Fe, Cu, Cd, Cr, Ca, Ni, and Pb by flame atomic absorption spectroscopy under optimum analytical conditions. The distribution of these metals in different operationally defined chemical fractions was also determined by using the sequential extraction technique. The highest mean total concentration was found for Fe while the least one was observed for Pb. All the studied metals were found to be present at levels much enhanced than national and international standards. Moreover, most of the metals were distributed principally in residual fraction with the exception of Ni which was found to be associated mainly with oxidizable fraction. The significant correlations were observed between Fe-Mn oxide-bound and residual fractions and exchangeable and oxidizable fractions for most of the metals. The highest mobility was exhibited by Ni that evidenced its enhanced bioavailability in the soil. The multivariate statistical analyses in terms of principal component analysis (PCA) and cluster analysis (CA) revealed multiple sources for various geochemical fractions of different metals. CA also revealed that the nonresidual fractions of most of the metals were very closely associated while PCA presented a distinctive behavior of Ca in the soil. It was therefore suggested that in order to avoid the metal contamination arising from industrial wastewater, appropriate remediation strategies must be adopted.     

Trace metal fractionation in the Pichavaram mangrove–estuarine sediments in southeast India after the tsunami of 2004

The geochemistry of coastal sediments of southern India was altered after the tsunami in 2004. A five-step sequential extraction procedure was applied to assess the effects of tsunami on mobility and redistribution of selected elements (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn). Ten surface sediments and three cores were analyzed for different metal fractions (exchangeable, carbonate, reduced, oxidized, and residual). Total metal concentrations increased in mangrove sediments after the tsunami, but their spatial distribution did not show significant variation (except Mn). The sediments were mixed by the tsunami, and there was lack of variation in metal concentrations in different fractions with depth (except Pb and Mn). High concentrations of Pb and Zn occurred in the oxide fractions, whereas Cu, Cr, Cd, and Ni were high in the organic and sulfide-rich fractions. Metals in the residual fraction (lattice bound) had the highest concentration suggesting their non-availability and limited biological uptake in the system. Most of the metals (except Mn) do not constitute a risk based on the different geochemical indices.     

Metal Leachability and Anthropogenic Signal in Roadside Soils Estimated from Sequential Extraction and Stable Lead Isotopes

Several roadside soil samples were collected at two field sites in Sweden. They were analysed for total elemental content (using both ICP-MS and XRF) and stable lead isotopes. Extraction with deicing salt solution and sequential extraction were performed in order to elucidate the potential mobility due to the use of deicing agents. The total concentrations of elements, especially lead, have decreased and lead is presently almost at background concentrations (15-51 ppm for surface samples). However, the isotopic signature indicates that old gasoline lead still is left at the site constructed prior to 1975. The field site constructed in 1992 showed, however, no 206Pb/207Pb ratio below 1.14. Only minor amounts were leached using deicing salt solutions; for lead only 0.29%, on average, was extracted indicating that the mobile fraction already was released. Sequential extraction indicated that lead mainly was associated with reducible (34.4%) and oxidisable (35.4%) fractions. Exchangable and acid soluble fractions contained 20.3% while 10.0% was found in the residual fraction. The salt extraction released, however, very low concentrations indicating that most in fraction 1 is acid soluble (e.g. carbonates). Tungsten was also found at high concentrations indicating a possible impact from studded tires. For tungsten the following composition was obtained: residual (48.0%) > oxidisable (47.6%) > reducible (3.3%) > exchangeable/acid soluble (1.1%). From the isotopic studies it was also suggested that the order for incorporating anthropogenic lead into soils is exchangeable/carbonates > (hydr)oxides > organic matter > residual. The multivariate technique principal component analysis (PCA) seems promising for evaluating large sequential extraction datasets.     

Fractionation and ecotoxicological implication of potentially toxic metals in sediments of three urban rivers and the Lagos Lagoon,Nigeria, West Africa

The potential environmental impact of sediment-bound Cd, Cr, Cu, Pb and Zn in three trans-urban rivers in Lagos state and in the Lagos Lagoon was assessed by use of the modified Community Bureau of Reference (BCR) sequential extraction. The quality of the data was checked using BCR CRM 143R and BCR CRM 701. Good agreement was obtained between found and certified/indicative values. Of the rivers, the Odo-Iyaalaro, was generally the most contaminated and the Ibeshe the least. Higher concentrations of metals were generally found in the dry season compared to the wet season. Cadmium and Zn were released mostly in the acid exchangeable step of the sequential extraction, indicating that they have the greatest potential mobility and bioavailability of the analytes studied. Chromium and Cu were associated mainly with the reducible and oxidisable fractions, and Pb predominantly with the reducible and residual fractions. Sediments with the highest pseudototal analyte concentrations also released higher proportions of analytes earlier in the sequential extraction procedure. The study suggests that, during the dry season, potentially toxic metals (PTM) may accumulate in sediments in relatively labile forms that are released and can potentially be transported or bioaccumulate in the rainy season. Application of risk assessment codes and Hankanson potential risk indices indicated that Cd was the element of greatest concern in the Lagos Lagoon system. The study indicated that there is a need to strengthen environmental management and pollution control measures to reduce risk from PTM, but that even relatively simple strategies, such as seasonal restrictions on dredging and fishing, could be beneficial.     

Determination of pollution trends in an abandoned mining site by application of a multivariate statistical analysis to heavy metals fractionation using SM&T-SES

The mobility, availability and persistence of Heavy Metals (HMs), As, Cd, Cu, Ni, Pb and Zn, in contaminated soils of a former abandoned mining area were evaluated by means of a sequential extraction scheme (SES) and applying a multivariate statistical analysis to the obtained data. Chemical partitioning of HMs in each sample was determined in four fractions (acid-soluble, reducible, oxidable and residual) following the Standard Measurements and Testing (SM&T) SES, formerly BCR-SES. Statistical evaluation of results by pattern recognition techniques allowed identification of groups of samples with similar characteristics and observations of correlations between variables, determining the pollution trends and distribution of HMs within the studied area. Typical metal-fraction association and metal availability characteristics of heavy metals have been depicted. The obtained results indicate an urgent need to attenuate the hazard in that area posed by high concentrations of toxic metals, which exceed the limits specified by different European legislations on soil reclamation.     

Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

广东某含铊硫酸冶炼堆渣场土壤中重金属的污染特征

选取广东某硫酸厂工业堆渣周围土壤样品,重点研究了土壤剖面T1、cd、Pb、Zn四种重金属元素总量及形态分布特征.研究结果表明,该废渣在自然淋滤条件下已经对周围土壤产生了T1、Cd、Pb、Zn污染,并且T1、Pb、Cd较Zn污染严重.形态分析表明,堆渣场周围土壤中这些重金属主要是以残渣态和铁锰氧化物(氢氧化物)结合态存在.外围土壤受到的这些重金属污染及对环境的潜在危害大于废渣下伏土壤,其中在堆渣下伏土壤中主要以富集为主,而外围土壤中主要以迁移为主,且已经向土壤深处约30cm处进行了迁移.这些重金属污染物在表层土壤中未达到饱和状态,将继续在下伏土壤表层发生累积作用并且使横向土壤受污染的范围进一步扩大.     

Accumulation and remobilization of metals in superficial sediments in Tianjin, China

The concentrations of Cr, Ni, Cu, Zn, Cd, and Pb in superficial sediment samples collected from three representative sites (Yuqiao Reservoir, Haihe River, and Haihe River Estuary) in Tianjin, North China, were analyzed using various single extraction and sequential extraction procedures to determine their remobilization, extractability, and distribution patterns. Sediments from the Haihe River had higher metal concentrations and geo-accumulation indices, especially for Cd and Zn, than sediments from the other two sites, suggesting that the Haihe River has been heavily influenced by anthropogenic activities. In addition, over 31% and 28.2% of the total Cd in the Haihe River and the Yuqiao Reservoir, respectively, and 18.2% of the total Zn in the Haihe River were found to be associated with the exchangeable form, indicating the significant remobilization of Cd and Zn when compared with Cr and Ni. However, over 98% of the Ni and 78% of the Cr were most closely associated with the residue and oxidizable fractions, which resulted in their becoming environmentally immobile. Based on the Environmental Protection Agency method 3050B, Cd and Zn had the greatest extraction efficiency when a single extraction procedure using 0.5-mol L^???1 HCl, 0.43-mol L^???1 HAcO, and 0.05-mol L^???1 ethylene-diamine-tetra-acetic acid was conducted, with extraction yields of up to 72%, 68%, and 56% for Cd and 50%, 49%, and 29% for Zn, respectively, being obtained for the Haihe River sediments. This was followed by the yields of Cu and Pb and, finally, those of unpolluted metals such as Cr and Ni. HCl and acetic acid extraction provided equivalent information for predicting Cd and Zn mobility in the sediments studied and produced suitable results for quick screening.     

Total concentrations, fractionation and mobility of heavy metals in soils of urban area of Guwahati, India

This work describes the results of assessment of the heavy metals, Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn in urban soil of Guwahati City, India from 31 sites of five different land use types covering residential, commercial, industrial, public utilities, and roadside. Sequential extraction procedure was used to evaluate the relative distribution of the eight metals in exchangeable, carbonate, reducible (Fe?CMn oxide), organic and sulfide, and residual fractions. Of the eight metals, Cd and Co occur in lower concentrations (Cd <?< Co) in all types of land, and concentration variation from one type of land use to another is not much significant for both the metals. Ni presence is more than Co, and the concentrations show some variation depending on land use status. Average Cr and Cu concentrations are ??100?mg/kg, but Cr has a significantly higher presence in industrial land use. The results are similar in case of Pb. The two metals, Mn and Zn have domination over the other metals, and the values are ??300?mg/kg. Industrial and roadside soil contains much more Mn, while commercial soil is most enriched with Zn. Of the metals, Ni has the largest proportion (~42%) bound to the exchangeable fraction and Co, Cr, and Pb also have appreciable proportion bound to the same fraction. A significant amount of Co is associated with carbonates. The reducible fraction has bound considerable quantity of Mn and Zn, while most of Cu is associated with the organic and sulfide fraction. Both Cd and Pb are dominantly associated with the residual fraction. Computation of the mobility factor of the metals indicates Mn to be the most mobile metal present in the soil samples.