粉煤灰基吸附剂去除水中重金属的研究进展

粉煤灰是一种廉价易得的工业废弃物,但因其具有呈化学惰性的表面、有限的孔结构、低的比表面积,使得其作为吸附剂应用于水中重金属离子的去除方面受到限制,改性处理可赋予粉煤灰新的吸附特性。文中系统介绍了改性粉煤灰材料的制备及其用于水中重金属去除方面的研究进展,比较分析粉煤灰基材料自身及其在重金属处理应用中的优缺点,重金属包括以Pb、Hg、Cd等为首的高毒性二价阳离子和以Cr、As为首的含氧酸根负离子。得出粉煤灰沸石材料具有应用前景,处理二价阳离子尤为有效,接枝改性有助于有毒Cr(Ⅵ)阴离子的去除。应增加低污染、低成本、高吸附容量的粉煤灰基吸附材料的开发及其在实际废水中的应用研究。     

海绵吸附材料去除水体中重金属离子的研究进展

海绵吸附材料因其孔隙丰富、比表面积大、机械性能良好、形状大小可控以及易于固液分离等诸多优势,在重金属污染水体处理领域得到广泛关注.但如何利用海绵吸附材料高效去除重金属离子并加强其应用的推广仍是研究的关键.本文总结了目前国内外在该领域的研究成果和进展,归纳了海绵吸附材料的制备方法、类型及吸附机理,介绍了影响海绵吸附材料吸...     

磁性氧化石墨烯制备及去除水中刚果红的研究

采用Hummer方法制备了氧化石墨烯(GO),采用化学共沉淀法把铁氧化物纳米粒子覆盖在GO上制成磁性氧化石墨烯(MGO),并把MGO用作吸附剂去除水中阴离子染料刚果红.采用扫描电镜(SEM)、透射电镜(TEM)、Zeta电位仪和磁强计对MGO进行了表征.研究了吸附动力学,吸附等温线及初始pH值,离子强度对吸附的影响.考察了MGO对自来水中刚果红的去除效果.结果表明,GO具有片状的二维纳米结构,表面有许多的褶皱;当pH3.5,吸附剂表面带负电荷,等电点为3.5;MGO的饱和磁化强度为31.2emu/g,足够从水溶液中分离出来.刚果红的吸附符合准二级动力学模型,且在吸附时间为7h内基本达到吸附平衡.在超纯水中最大吸附容量高达140.6mg/g,且吸附量随pH值升高先增加再降低,当pH4~5达到最大值.MGO对自来水中刚果红的最大吸附容量为287.6 mg/g,为在超纯水中的2倍,表明MGO对刚果红具有很好的去除效果.     

改性氧化石墨烯/壳聚糖功能材料对刚果红的吸附研究

以氧化石墨烯(GO)和壳聚糖(CS)为前体物,以乙二胺四乙酸二钠(EDTA-2Na)为表面改性剂,制备了一种新型改性氧化石墨烯/壳聚糖功能材料(GEC),并将此材料作为吸附剂用于水中刚果红的吸附去除,探讨了时间、pH值、吸附剂投加量、温度及初始浓度对GEC吸附去除刚果红的影响.结果表明,GEC对水中刚果红具备良好的吸附能力,且在pH=2~12的范围内都具有较佳的吸附效果.GEC对刚果红的吸附动力学可以较好地用伪二级动力学模型进行描述,其吸附数据可应用Langmuir吸附等温模型进行拟合,其吸附过程是自发的吸热反应过程.根据Langmuir模型计算得到GEC室温条件下最大吸附量为175.43 mg·g~(-1).用2 mol·L~(-1)NaOH溶液在60℃水浴条件下对GEC进行脱附再生实验,在重复循环利用6次后,GEC对刚果红的吸附量仅下降了5.89%,刚果红的去除率仍保持在88%以上.以上结果表明,GEC适合作为一种有效的吸附剂去除水中刚果红.     

环境矿物材料吸附重金属的有机改性研究

环境矿物材料应用在重金属污染治理中越来越受到人们的关注,而通过有机改性可以有效提高其治理效果。结合国内外对环境矿物材料的有机改性研究,综述了应用于重金属污染治理的环境矿物材料有机改性的研究进展,并提出了发展趋势和展望。     

改性材料对土壤重金属污染修复的进展研究

化学修复是土壤重金属污染治理的技术手段之一,使用修复材料对土壤中的重金属进行吸附和固定是其进行土壤修复的主要途径.为了提高修复材料的性能,增强对重金属的吸附性和固定作用,减少土壤环境多样性对修复材料性能的影响,通过化学及物理方法对石灰石、磷酸盐等传统化学修复材料进行改性,提升在土壤修复中的性能,培育和筛选应用范围广、抗干扰性强,环境适应性好的改性材料是近一段时间在土壤修复方向研究的重点.     

矿井水中氟化物及放射性核素去除研究

对淮北芦岭矿区饮用水源中氟化物及放射性核素去除工艺与机理进行了探讨,试验证明以聚合铝作混凝剂的混凝沉淀方法对去除氟化物及放射性核素非常有效,当PAC用量为20mg/L时,饮水中氟化物含量由1.85mg/L降至0.78mg/L?总α由0.13Bq/L降至0.03Bq/L?总β由0.26Bq/L降至0.18Bq/L?      

石墨烯类材料在水处理和地下水修复中的应用

作为一种性质优异的吸附材料,石墨烯类材料对有机物和重金属等多种水污染物均有出色的吸附能力,因此其在水处理和地下水修复工作中的应用前景在近几年备受关注.当前的研究总体上尚停留在实验室模拟阶段,在提高材料饱和吸附量的同时,研制出低成本、稳定性强、易于再生利用且环境友好的石墨烯类材料是今后的发展趋势.本文对石墨烯类材料的种类及制备方法进行了归纳总结,对他们在水处理和地下水修复中的应用研究情况进行了综述,对当前研究中存在的问题进行了分析,最后对未来的研究和应用前景进行了总结和展望.     

吸附材料对钒矿污染土壤重金属的稳定化效果

选用壳聚糖和活性炭两种吸附材料,分别以不同的质量比添加到供试土壤中,固化后进行毒性浸出实验,研究吸附材料对土壤中钒(V)、铬(Cr)的稳定化效果,并通过表征吸附材料的红外光谱(FTIR)和X射线光电子能谱(XPS)探究吸附材料对V、Cr的稳定化机理.结果表明,壳聚糖对V、Cr均有较好的稳定化效果,活性炭对V的稳定化效果不稳定,对Cr的稳定化效果很好.吸附材料添加量的改变对稳定化效果影响不大.稳定化30d时,0.5%壳聚糖对V、Cr的稳定化率分别为74.04%、46.77%;0.5%活性炭对V、Cr的稳定化率分别为1.86%、87.75%.FTIR和XPS表征结果表明,壳聚糖中含活性强的氨基和羟基较多,活性炭中含氨基、羟基较少.因此壳聚糖和活性炭可作为土壤重金属的稳定剂,使钒矿污染土壤得到修复.     

改性栗壳吸附重金属离子的动力学及热力学研究

对改性板栗壳吸附Cr(VI)、Cu(II)及Ni(II)3种重金属离子过程的动力学和热力学进行研究。结果表明:改性板栗壳吸附Cr(VI)、Cu(II)和Ni(II)3种混合离子时存在拮抗的竞争关系,竞争吸附顺序为Cu(II)﹤Ni(II)﹤Cr(VI);与单独吸附过程相比,混合吸附平衡时,改性板栗壳对3种离子相应的去除率均有所降低,Cr(VI)去除率比单独吸附时降低20.2%,Cu(II)和Ni(II)分别降低40.7%和35.6%;拟二级动力学方程能很好地描述Cr(VI)、Cu(II)和Ni(II)在改性板栗壳上的单独和混合吸附过程,结果表明此3种重金属离子在改性板栗壳表面以化学吸附为主;热力学研究数据表明:改性板栗壳对Cr(VI)的吸附为吸热反应,对Cu(II)和Ni(II)的吸附为放热反应。     

Removal of heavy metals from aqueous solution by carbon nanotubes: adsorption equilibrium and kinetics

IntroductionWastewatersfrombatterymanufacturing ,printing ,painting ,dyeingandotherindustrialprocessesoftencontainconsiderableamountsofheavymetalsthatwouldendangerpublichealthifdischargedwithoutadequatetreatment.Long termingestionofwatercontaininghigherco…     

Removal of heavy metals from aqueous solution by sawdust adsorption

The adsorption of lead, cadmium and nicel from aqueous solution by sawdust of walnut was investigated. The effect of contact time, initial metal ion concentration and temperature on metal ions removal has been studied. The equilibrium time was found to be of the order of 60 min. Kinetics fit pseudo first-order, second-order and intraparticle diffusion models, hence adsorption rate constants were calculated. The adsorption data of metal ions at temperatures of 25, 45 and 60~C have been described by the Freundlich and Langmuir isotherm models. The thermodynamic parameters such as energy, entropy and enthalpy changes for the adsorption of heavy metal ions have also been computed and discussed. Ion exchange is probably one of the major adsorption mechanisms for binding divalent metal ions to the walnut sawdust. The selectivity order of the adsorbent is Pb（I1）~Cd（II）〉Ni（I1）. From these results, it can be concluded that the sawdust of walnut could be a good adsorbent for the metal ions from aqueous solutions.     

Removal of heavy metal ions from aqueous solution using red loess as an adsorbent

The adsorption behaviors of heavy metals onto novel low-cost adsorbent, red loess, were investigated. Red loess was characterized by X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectra. The results indicated that red loess mainly consisted of silicate, ferric and aluminum oxides. Solution pH, adsorbent dosage, initial metal concentration, contact time and temperature significantly influenced the efficiency of heavy metals removal. The adsorption reached equilibrium at 4 hr, and the experimental equilibrium data were fitted to Langmuir monolayer adsorption model. The adsorption of Cu(II) and Zn(II) onto red loess was endothermic, while the adsorption of Pb(II) was exothermic. The maximum adsorption capacities of red loess for Pb(II), Cu(II) and Zn(II) were estimated to be 113.6, 34.2 and 17.5 mg/g, respectively at 25°C and pH 6. The maximum removal efficiencies were 100% for Pb(II) at pH 7, 100% for Cu(II) at pH 8, and 80% for Zn(II) at pH 8. The used adsorbents were readily regenerated using dilute HC1 solution, indicating that red loess has a high reusability. All the above results demonstrated that red loess could be used as a possible alternative low-cost adsorbent for the removal of heavy metals from aqueous solution.     

Removal of heavy metals through adsorption using sand

ＩｎｔｒｏｄｕｃｔｉｏｎＷａｔｅｒｃｏｎｔａｍｉｎａｎｔｓｉｎｃｌｕｄｅａｌａｒｇｅｎｕｍｂｅｒｏｆｃｈｅｍｉｃａｌｓｒａｎｇｉｎｇｆｒｏｍａｒｏｍａｔｉｃｈｙｄｒｏｃａｒｂｏｎｓ,ｏｒｇａｎｉｃｓｏｌｖｅｎｔｓ,ｐｅｓｔｉｃｉｄｅｓａｎｄｍｅｔａｌｓ.Ｈｅａｖｙｍｅｔａｌｃｏｎｔａｍｉｎａｔｉｏｎｉｓｃｏｍｍｏｎｌｙｆｏｕｎｄｉｎａｒｅａｓｗｈｅｒｅｉｎｄｕｓｔｒｉａｌｅｆｆｌｕｅｎｔｓａｒｅｄｉｓｃｈａｒｇｅｄｉｎｔｏｎａｔｕｒａｌｗａｔｅｒｓ .Ｔｈｅｈａｒｍｆｕｌｅｆｆｅｃｔｓｏｆｓｕｃｈｍ…     

Removal of heavy metals from artificial metals contaminated water samples based on micelle-templated silica modified with pyoverdin I

The micelle-templated silica (MTS) was firstly chemically modified with 3-glycidoxypropyl-trimethoxysilane (GPTMS) before immobilized with pyoverdin I. The characteristics of pyoverdin I-anchored onto the modified MTS were investigated using fluorescence, infrared spectra and scanning electron microscopy. The specific surface area of all materials was calculated by Bnmauer, Emmett and Teller (BET) method using nitrogen isotherm adsorption data. As the results, the surface area of commercial silica gel decreased from 609.2 to 405.4 m2/g, it indicated that the pyoverdin I could be immobilized onto the surface of silica solid support. This adsorbent was used for extraction of Fe(Ⅲ), Cu(Ⅱ), Zn(Ⅱ), and Pb(Ⅱ) in artificial metals contaminated water. Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using batch procedure. The optimum pH value for the removal of metal ions simultaneously on this adsorbent was 4.0. Complete desorption of the adsorbed metal ions from the adsorbent was carded out using 0.25 mol/L of EDTA. The effcct of different cations and anions on the adsorption of these metals on adsorbent was studied and the results showed that the proposed adsorbent could be applied to the highly saline samples and the sample which contains some transition metals.     

电化学方法去除污泥中重金属的研究

分析了河东污水处理厂污泥中Pb、Cd、Cu、Ni的含量和形态分布特征,并以PbO2/Ti电极板为阳极、铜板为阴极通电处理污泥,考察了电压、通电时间等因素对污泥pH及重金属去除效果的影响.结果表明,污泥中Cd和Ni的含量超过了国家农用标准(GB4284—1984),同时,Cd和Ni也具有较高的生态可利用性.不同电压对污泥重金属去除率影响较大,当电压为35 V,电流为80 mA,反应时间为6 h时,对污泥的处理效果与费用最佳,在此电压下对污泥进行处理,Cu、Pb、Cd和Ni的去除率分别为57.35%、48.42%、68.63%和49.85%.此时,阳极区污泥中的重金属含量已有较大程度的降低,均能达到国家农用标准(GB4284—1984).     

采用电动修复增强技术去除电镀污泥中重金属

为提高电动修复技术去除电镀污泥中的重金属(Cu, Pb, Zn , Cr, Ni)的效率,采用污泥预酸化处理及阴极pH值控制处理2种途径进行强化,反应过程中电压为32V,处理时间为7d,结果表明,电镀污泥酸化pH值至4.5时,污泥中重金属的可移动性明显提高了,依次为Cr>Ni>Zn>Cu>Pb;污泥预酸化加阴极pH值控制处理能使电镀污泥中Zn、Ni、Cu和Pb交换态、碳酸盐结合态和有机硫化物态转化为可溶离子态,转化量大小依次为Ni>Zn>Cu>Pb,且该处理Zn、Ni、Cu和Pb的去除率分别达到74.02%、68.38%、39.22%、21.37%;但污泥预酸化及阴极pH值控制处理都不利于Cr的去除,对照处理Cr去除率为77.83%,污泥预酸化处理去除率降为40.65%,污泥预酸化加阴极pH值控制处理降至12.80%.     

Removal of humic acid from aqueous solution by cetylpyridinium bromide modified zeolite

Natural zeolite was modified by loading cetylpyridinium bromide (CPB) to create more e cient sites for humic acid (HA) adsorption. The natural and CPB modified zeolites were characterized with X-ray di raction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy and elemental analysis. The e ects of various experimental parameters such as contact time, initial HA concentration, solution pH and coexistent Ca2+, upon HA adsorption onto CPB modified zeolites were evaluated. The results showed that natural zeolite had negligible a nity for HA in aqueous solutions, but CPB modified zeolites exhibited high adsorption e ciency for HA. A higher CPB loading on natural zeolites exhibited a larger HA adsorption capacity. Acidic pH and coexistent Ca2+ were proved to be favorable for HA adsorption onto CPB modified zeolite. The kinetic process was well described by pseudo second-order model. The experimental isotherm data fitted well to Langmuir and Sips models. The maximum monolayer adsorption capacity of CPB modified zeolite with surfactant bilayer coverage was found to be 92.0 mg/g.     

柠檬酸对重金属复合污染土壤的浸提效果研究

以浙江富阳某炼铜厂附近受Cd、Cu、Pb和Zn复合污染的土壤为研究对象,采用振荡、静置和超声3种不同浸提方式,通过研究柠檬酸在不同浸提方式下对重金属的去除效果,筛选出最佳柠檬酸浓度、处理时间及功率,并采用Tessier连续提取法分析浸提前后4种重金属形态变化.结果表明,柠檬酸对4种重金属均具有较好的去除效果,其中对Zn的去除效果最好,Cd的去除效果最差,而Cu和Pb的去除效果相当.Pb和Zn的去除率均随着柠檬酸浓度的增加而增加,但增幅随之减小,Cu的去除率则先增加后基本保持不变,而Cd的去除率变化不明显.综合考虑成本和浸提效果后,选用0.2 mol·L-1柠檬酸浸提2次为最优条件,最佳振荡时间和静置时间分别为4 h和24 h,最佳超声时间和功率分别为30 min和500 W.柠檬酸能够在很大程度上改变土壤中重金属的形态分布,主要去除以可交换态和碳酸盐结合态形式存在的Cd及以碳酸盐结合态和铁锰氧化物结合态形式存在的Cu、Pb和Zn.通过对比3种浸提方式,在同等去除效果的前提下,静置浸提相比振荡浸提需要更长的时间,而将超声波应用于重金属污染土壤淋洗,所需时间较少,因此,超声波辅助浸提土壤中重金属是可行的,具有良好的应用前景.     

生物沥浸对自然干化污泥重金属去除效果研究

重金属的去除是污泥农用需要解决的关键问题之一.本研究采用摇瓶实验,将氧化硫硫杆菌为功能微生物的生物沥浸技术应用于干化污泥重金属的去除,对山西省不同污水处理厂11个干化污泥样品进行了为期15 d的生物沥浸处理.分析了生物沥浸体系p H及SO2-4的变化情况,并对生物沥浸前后污泥中Cu、Zn、As、Cd、Cr等重金属去除率及有机质、全氮、全磷、全钾等养分的损失率进行了分析.结果表明,干污泥直接进行生物沥浸过程较为缓慢,无机酸对体系的酸化能够快速启动干化污泥的生物沥浸过程.无机酸酸化后,体系S0的生物氧化率逐渐提高,酸化速率加快,且污泥重金属去除率随着p H的降低而提高,生物沥浸过程结束后,供试污泥样品Cu、Zn、As、Cd和Cr的去除率分别为23.69%~77.62%、89.67%~97.80%、30.24%~84.31%、18.18%~97.05%和28.55%~67.11%,而污泥有机质、全氮、全磷和全钾的含量损失率分别为3%、1%、44%和8%,污泥剩余养分含量满足农用泥质标准(CJ/T309-2009)的限定值.Cu、Zn、As、Cd和Cr去除率与污泥有机质含量呈显著负相关关系(r=0.935、0.895、0.932、0.516、0.847,n=11).