Direct individual analysis using Scanning Electron Microscopy combined with online observation was conducted to examine the S-rich particles in PM2.5 of two typical polluted haze episodes in summer and winter from 2014 to 2015 in Beijing. Four major types of S-rich particles, including secondary CaSO4 particles (mainly observed in summer), S-rich mineral particles (SRM), S-rich water droplets (SRW) and (C, O, S)-rich particles (COS) were identified.We found the different typical morphologies and element distributions of S-rich particles and considered that (C, O, S)-rich particles had two major mixing states in different seasons. On the basis of the S-rich particles’ relative abundances, S concentrations and their relationships with PM2.5 as well as the seasonal comparison, we revealed that the S-participated formation degrees of SRM and SRW would enhance with increasing PM2.5 concentration. Moreover, C-rich matter and sulfate had seasonally different but significant impacts on the formation of COS.
For biological nitrogen (N) removal from wastewater, a sufficient organic carbon source is requested for denitrification. However, the organic carbon/nitrogen ratio in municipal wastewater is becoming lower in recent years, which increases the demand for the addition of external organic carbon, e.g. methanol, in wastewater treatment. The volatile fatty acids (VFAs) produced by acidogenic fermentation of sewage sludge can be an attractive alternative for methanol. Chemically enhanced primary sedimentation (CEPS) is an effective process that applies chemical coagulants to enhance the removal of organic pollutants and phosphorus from wastewater by sedimentation. In terms of the chemical and biological characteristics, the CEPS sludge is considerably different from the conventional primary and secondary sludge. In the present study, FeCl3 and PACl (polyaluminum chloride) were used as the coagulants for CEPS treatment of raw sewage. The derived CEPS sludge (Fe-sludge and Al-sludge) was then processed with mesophilic acidogenic fermentation to hydrolyse the solid organics and produce VFAs for organic carbon recovery, and the sludge acidogenesis efficiency was compared with that of the conventional primary sludge and secondary sludge. The results showed that the Fe-sludge exhibited the highest hydrolysis and acidogenesis efficiency, while the Al-sludge and secondary sludge had lower hydrolysis efficiency than that of primary sludge. Utilizing the Fe-sludge fermentation liquid as the carbon source for denitrification, more than 99% of nitrate removal was achieved in the main-stream wastewater treatment without any external carbon addition, instead of 35% obtained from the conventional process of primary sedimentation followed by the oxic/anoxic (O/A) treatment.
Ibuprofen (IBU) is widely used in the world as anti-inflammatory drug, which posed health risk to the environment. A bacterium capable of degrading IBU was isolated from activated sludge in a sewage treatment plant. According to its morphological, physiologic, and biochemical characteristics, as well as 16S rRNA sequence analysis, the strain was identified as Serratia marcescens BL1 (BL1). Degradation of IBU required the presence of primary substrate. After a five-day cultivation with yeast powder at 30°C and pH 7, the highest degradation (93.47%±2.37%) was achieved. The process of BL1 degrading IBU followed first-order reaction kinetics. The BL1 strain was applied to a small biological aerated filter (BAF) device to form a biofilm with activated sludge. IBU removal by the BAF was consistent with the results of static tests. The removal of IBU was 32.01% to 44.04% higher than for a BAF without BL1. The indigenous bacterial community was able to effectively remove CODMn (permanganate index) and ammonia nitrogen in the presence of BL1.
Bdellovibrio-and-like organisms (BALOs) are a group of ubiquitous and obligate predatory bacteria and commonly used as biocontrol agents. In this study, an efficient, environmental-friendly, and convenient BALOs encouraged municipal waste sludge biolysis pretreatment technique was developed and investigated for dewaterability enhancement of excess waste sludge. The indigenous predatory BALOs were successfully isolated from the sludge for biolysis treatment. Without any chemical addition or pH adjustment, the sludge specific resistance (SRF) and capillary suction time (CST) were significantly reduced by as high as 53.4% and 23.8%, respectively within 24 h’s treatment, which would further be lowered with the increase of BALOs input dosage. However, the continuous extension of reaction time would worsen the sludge dewaterability. The decreases of SRF and CST accompanied with the increases of sludge disintegration degree and soluble chemical oxygen demand, nitrogen, and phosphorus concentrations all emphasized the contributions of BALOs’ predation activities to sludge disturbance, cell lysis, and consequently the release of sludge intracellular water to finally effectively improve the sludge dewaterability and disposal efficiency.
Biofilm is an effective simultaneous denitrification and in situ sludge reduction system, and the characteristics of different biofilm carrier have important implications for biofilm growth and in situ sludge reduction. In this study, the performance and mechanism of in situ sludge reduction were compared between FSC-SBBR and SC-SBBR with constructed by composite floating spherical carriers (FSC) and multi-faceted polyethylene suspension carriers (SC), respectively. The variation of EPS concentration indicated that the biofilm formation of FSC was faster than SC. Compared with SCSBBR, the FSC-SBBR yielded 0.16 g MLSS/g COD, almost 27.27% less sludge. The average removal rates of COD and NH4+-N were 93.39% and 96.66%, respectively, which were 5.21% and 1.43% higher than the average removal rate of SC-SBBR. Investigation of the mechanisms of sludge reduction revealed that, energy uncoupling metabolism and sludge decay were the main factors for sludge reduction inducing 43.13% and 49.65% less sludge, respectively, in FSC-SBBR. EEM fluorescence spectroscopy and SUVA analysis showed that the hydrolytic capacity of biofilm attached in FSC was stronger than those of SC, and the hydrolysis of EPS released more DOM contributed to lysis-cryptic growth metabolism. In additional, Bacteroidetes and Mizugakiibacter associated with sludge reduction were the dominant phylum and genus in FCS-SBBR. Thus, the effect of simultaneous in situ sludge reduction and pollutant removal in FSC-SBBR was better.
This work presents an overall introduction to the Station for Observing Regional Processes of the Earth System–SORPES in Nanjing, East China, and gives an overview about main scientific findings in studies of air pollution-weather/climate interactions obtained since 2011. The main results summarized in this paper include overall characteristics of trace gases and aerosols, chemical transformation mechanisms for secondary pollutants like O3, HONO and secondary inorganic aerosols, and the air pollution–weather/climate interactions and feedbacks in mixed air pollution plumes from sources like fossil fuel combustion, biomass burning and dust storms. The future outlook of the development plan on instrumentation, networking and data-sharing for the SORPES station is also discussed.
Arsenic (As) is a pervasive environmental toxin and carcinogenic metalloid. It ranks at the top of the US priority List of Hazardous Substances and causes worldwide human health problems. Wetlands, including natural and artificial ecosystems (i.e. paddy soils) are highly susceptible to As enrichment; acting not only as repositories for water but a host of other elemental/chemical moieties. While macroscale processes (physical and geological) supply As to wetlands, it is the micro-scale biogeochemistry that regulates the fluxes of As and other trace elements from the semi-terrestrial to neighboring plant/aquatic/atmospheric compartments. Among these fine-scale events, microbial mediated As biotransformations contribute most to the element’s changing forms, acting as the ‘switch’ in defining a wetland as either a source or sink of As. Much of our understanding of these important microbial catalyzed reactions follows relatively recent scientific discoveries. Here we document some of these key advances, with focuses on the implications that wetlands and their microbial mediated transformation pathways have on the global As cycle, the chemistries of microbial mediated As oxidation, reduction and methylation, and future research priorities areas.
A new type of Au/TiO2/reduced graphene oxide (RGO) nanocomposite was fabricated by the hydrothermal synthesis of TiO2 on graphene oxide followed by the photodeposition of Au nanoparticles. Transmission electron microscopy images showed that Au nanoparticles were loaded onto the surface of both TiO2 and RGO. Au/TiO2/RGO had a better photocatalytic activity than Au/ TiO2 for the degradation of phenol. Electrochemical measurements indicated that Au/TiO2/RGO had an improved charge transfer capability. Meanwhile, chemiluminescent analysis and electron spin resonance spectroscopy revealed that Au/TiO2/RGO displayed high production of hydrogen peroxide and hydroxyl radicals in the photocatalytic process. This high photocatalytic performance was achieved via the addition of RGO in Au/TiO2/RGO, where RGO served not only as a catalyst support to provide more sites for the deposition of Au nanoparticles but also as a collector to accept electrons from TiO2 to effectively reduce photogenerated charge recombination.
Three acid-producing strains, AFB-1, AFB-2 and AFB-3, were isolated during this study, and their roles in anaerobic digestion of waste activated sludge (WAS) were evaluated. Data of 16S rRNA method showed that AFB-1 and AFB-2 were Bacillus coagulans, and AFB-3 was Escherichia coli. The removal in terms of volatile solids (VS) and total chemical oxygen demand (TCOD) was maximized at 42.7% and 44.7% by inoculating Bacillus coagulans AFB-1. Besides, the optimal inoculum concentration of Bacillus coagulans AFB-1 was 30% (v/v). Solubilization degree experiments indicated that solubilization ratios (SR) of WAS reached 20.8%±2.2%, 17.7%±1.48%, and 11.1%±1.53%. Volatile fatty acids (VFAs) concentrations and compositions were also explored with a gas chromatograph. The results showed that VFAs improved by 98.5%, 53.0% and 11.6% than those of the control, respectively. Biochemical methane potential (BMP) experiments revealed that biogas production increased by 90.7% and 75.3% when inoculating with Bacillus coagulans AFB-1 and AFB-2. These results confirmed that the isolated acid-producing bacteria, especially Bacillus coagulans, was a good candidate for anaerobic digestion of WAS.
Methane fermentation process can be restricted and even destroyed by the accumulation of propionate because it is the most difficult to be anaerobically oxidized among the volatile fatty acids produced by acetogenesis. To enhance anaerobic wastewater treatment process for methane production and COD removal, a syntrophic propionate-oxidizing microflora B83 was obtained from an anaerobic activated sludge by enrichment with propionate. The inoculation of microflora B83, with a 1:9 ratio of bacteria number to that of the activated sludge, could enhance the methane production from glucose by 2.5 times. With the same inoculation dosage of the microflora B83, COD removal in organic wastewater treatment process was improved from 75.6% to 86.6%, while the specific methane production by COD removal was increased by 2.7 times. Hydrogen-producing acetogenesis appeared to be a rate-limiting step in methane fermentation, and the enhancement of hydrogen-producing acetogens in the anaerobic wastewater treatment process had improved not only the hydrogen-producing acetogenesis but also the acidogenesis and methanogenesis.
Because the efficiency of biological nutrient removal is always limited by the deficient carbon source for the low carbon/nitrogen (C/N) ratio in real domestic sewage, the denitrifying phosphorus removal (DNPR) was developed as a simple and efficient method to remove nitrogen and phosphorous. In addition, this method has the advantage of saving aeration energy while reducing the sludge production. In this context, a pre-denitrification anaerobic/anoxic/post-aeration + nitrification sequence batch reactor (pre-A2NSBR) system, which could also reduce high ammonia effluent concentration in the traditional two-sludge DNPR process, is proposed in this work. The pre-A2NSBR process was mainly composed of a DNPR SBR and a nitrifying SBR, operating as alternating anaerobic/anoxic/post-aeration + nitrification sequence. Herein, the long-term performance of different nitrate recycling ratios (0–300%) and C/N ratios (2.5–8.8), carbon source type, and functional microbial community were studied. The results showed that the removal efficiency of total inorganic nitrogen (TIN, including NH4+-N, NO2– -N, and NO3– -N) gradually increased with the nitrate recycling ratios, and the system reached the highest DNPR efficiency of 94.45% at the nitrate recycling ratio of 300%. The optimum C/N ratio was around 3.9–7.3 with a nitrogen and phosphorus removal efficiency of 80.15% and 93.57%, respectively. The acetate was proved to be a high-quality carbon source for DNPR process. The results of fluorescence in situ hybridization (FISH) analysis indicated that nitrifiers and phosphorus accumulating organisms (PAOs) were accumulated with a proportion of 19.41% and 26.48%, respectively.
This paper presents an investigation of the feasibility of recycling silicon carbide waste (SCW) as a source of mixture materials in the production of cement mortar. Mortars with SCW were prepared by replacing different amounts of cement with SCW, and the properties of the resulting mortars, such as the fluidity, strength and shrinkage, were studied in this work. Thermogravimetry-differential scanning calorimetry and scanning electron microscopy were employed to understand the reasons for the property changes of the mortars. The results indicate that SCW decreases the initial and 1-h fluidity of fresh mortar but improves the loss of fluidity. The mortar with SCWexhibits a lower strength at 3 d and 7 d but a higher strength at 28 d and 56 d compared to the control. The shrinkage rate of cement mortar with SCW shows an obvious decrease as the replacement ratio increases. In addition, the content of calcium hydroxide in hardened paste also shows that SCW has some impact on the hydration of the cement-SCW system. The microstructures of the hardened paste also show evidence for a later strength change of mortar containing SCW. This work provides a strategic reference for possibly applying SCW as a mixture material in the production of cement mortar.
A spent fluid catalytic cracking (FCC) catalyst containing lanthanum (La) was used as a novel adsorbent for phosphorus (P) in simulated wastewater. The experiments were conducted in a batch system to optimize the operation variables, including pH, calcination temperature, shaking time, solid-liquid ratio, and reaction temperature under three initial P-concentrations (C0 = 0.5, 1.0, and 5.0 mg/L). Orthogonal analysis was used to determine that the initial P-concentration was the most important parameter for P removal. The P-removal rate exceeded 99% and the spent FCC catalyst was more suitable for use in low P-concentration wastewater (C0 <5.0 mg/L). Isotherms, thermodynamics and dynamics of adsorption are used to analyze the mechanism of phosphorus removal. The results show that the adsorption is an endothermic reaction with high affinity and poor reversibility, which indicates a low risk of second releasing of phosphate. Moreover, chemical and physical adsorption coexist in this adsorption process with LaPO4 and KH2PO4 formed on the spent FCC catalyst as the adsorption product. These results demonstrate that the spent FCC catalyst containing La is a potential adsorbent for P-removal from wastewater, which allows recycling of the spent FCC catalyst to improve the quality of water body.
In this study, post plasma-catalysis degradation of mixed volatile organic compounds (benzene, toluene, and xylene) has been performed in a hybrid surface/packed-bed discharge plasma reactor with Ag-Ce/g-Al2O3 catalyst at room temperature. The effect of relative air humidity on mixed VOCs degradation has also been investigated in both plasma-only and PPC systems. In comparison to the plasma-only system, a significant improvement can be observed in the degradation performance of mixed VOCs in PPC system with Ag-Ce/γ-Al2O3 catalyst. In PPC system, 68% benzene, 89% toluene, and 94% xylene were degraded at 800 J·L–1, respectively, which were 25%, 11%, and 9% higher than those in plasma-only system. This result can be attributed to the high catalytic activity of Ag-Ce/γ-Al2O3 catalyst to effectively decompose O3 and lead to generating more reactive species which are capable of destructing the VOCs molecules completely. Moreover, the presence of Ag-Ce/γ-Al2O3 catalyst in plasma significantly decreased the emission of discharge byproducts (NOx and O3) and promoted the mineralization of mixed VOCs towards CO2. Adding a small amount of water vapor into PPC system enhanced the degradation efficiencies of mixed VOCs, however, further increasing water vapor had a negative impact on the degradation efficiencies, which was primarily attributed to the quenching of energetic electrons by water vapor in plasma and the competitive adsorption of water vapor on the catalyst surface. Meanwhile, the catalysts before and after discharge were characterized by the Brunauer-Emment-Teller and X-ray photoelectron spectroscopy.
The relationship between the improvement of sludge dewaterability and variation of organic matters has been studied in the process of sludge pre-conditioning with modified cinder, especially for extracellular polymeric substances (EPS) in the sludge. During the conditioning process, the decreases of total organic carbon (TOC) and soluble chemical oxygen demand (SCOD) were obviously in the supernatant especially for the acid modified cinder (ACMC), which could be attributed to the processes of adsorption and sweeping. The reduction of polysaccharide and protein in supernatant indicated that ACMC might adsorb EPS so that the tightly bound EPS (TB-EPS) decreased in sludge. In the case of ACMC addition with 24 g·L–1, SRF of the sludge decreased from 7.85 × 1012 m·kg–1 to 2.06 × 1012 m·kg–1, and the filter cake moisture decreased from 85% to 60%. The reconstruction of “floc mass” was confirmed as the main sludge conditioning mechanism. ACMC promoted the dewatering performance through the charge neutralization and adsorption bridging with the negative EPS, and provided firm and dense structure for sludge floc as skeleton builder. The passages for water quick transmitting were built to avoid collapsing during the high-pressure process.
Polycyclic aromatic hydrocarbons (PAHs) often occur in oil-contaminated soil, coke wastewater and domestic sludge; however, associated PAH degraders in these environments are not clear. Here we evaluated phenanthrene degradation potential in the mixed samples of above environments, and obtained a methanogenic community with different microbial profile compared to those from sediments. Phenanthrene was efficiently degraded (1.26 mg/L/d) and nonstoichiometric amount of methane was produced simultaneously. 16S rRNA gene sequencing demonstrated that bacterial populations were mainly associated with Comamonadaceae Nocardiaceae and Thermodesulfobiaceae, and that methanogenic archaea groups were dominated by Methanobacterium and Methanothermobacter. Substances such as hexane, hexadecane, benzene and glucose showed the most positive effects on phenanthrene degradation. Substrate utilization tests indicated that this culture could not utilize other PAHs. These analyses could offer us some suggestions on the putative phenanthrene-degrading microbes in such environments, and might help us develop strategies for the removal of PAHs from contaminated soil and sludge.
Eutrophication with a large number of Microcystis aeruginosa commonly occurs worldwide, thereby threatening the aquatic ecosystem and human health. In this study, four kinds of algicides were tested to explore their influence on cell density and chlorophyll-a of M. aeruginosa. Results showed that aluminum silicate agent, which inhibited more than 90% cell growth compared with the control group, demonstrated the strongest inhibition effect immediately on M. aeruginosa growth. Furthermore, the production and release of microcystin (MC)-LR were investigated. Aluminum silicate, CuSO4, and Emma-11 were more effective than pyrogallic acid in disrupting the cells of M. aeruginosa, thereby increasing the extracellular MC-LR concentration. Aluminum silicate caused the highest extracellular MC-LR concentration of more than 45 mg·L–1. Biotoxicity was also detected to evaluate the environmental risks of MC-LR release, which were related to the usages of different algicides. Extracellular MC-LR concentration mostly increased when the biotoxicity of algae solution increased. The experiments were also designed to reveal the effects of physical conditions in riverways, such as natural sunlight, aeration and benthal sludge, on MC-LR degradation. These findings indicated that UV rays in sunlight, which can achieve a MC-LR removal efficiency of more than 15%, played an important role in MC-LR degradation. Among all the physical pathways of MC-LR removal, benthal sludge adsorption presented the optimal efficiency at 20%.
Cadmium (Cd) and lead (Pb) in water and soil could be adsorbed by biochar produced from corn straw. Biochar pyrolyzed under 400°C for 2 h could reach the ideal removal efficiencies (99.24%and 98.62% for Cd and Pb, respectively) from water with the biochar dosage of 20 g·L–1 and initial concentration of 20 mg·L–1. The pH value of 4–7 was the optimal range for adsorption reaction. The adsorption mechanism was discussed on the basis of a range of characterizations, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and Raman analysis; it was concluded as surface complexation with active sorption sites (-OH, -COO-), coordination with π electrons (C = C, C = O) and precipitation with inorganic anions (OH-, CO32–, SO42–) for both Cd and Pb. The sorption isotherms fit Langmuir model better than Freundlich model, and the saturated sorption capacities for Cd and Pb were 38.91 mg·g-1 and 28.99 mg·g–1, respectively. When mixed with soil, biochar could effectively increase alkalinity and reduce bioavailability of heavy metals. Thus, biochar derived from corn straw would be a green material for both removal of heavy metals and amelioration of soil.
In this study, super-fine powdered activated carbon (SPAC) has been proposed and investigated as a novel catalyst for the catalytic ozonation of oxalate for the first time. SPAC was prepared from commercial granular activated carbon (GAC) by ball milling. SPAC exhibited high external surface area with a far greater member of meso- and macropores (563% increase in volume). The catalytic performances of activated carbons (ACs) of 8 sizes were compared and the rate constant for pseudo first-order total organic carbon removal increased from 0.012 min–1 to 0.568 min–1 (47-fold increase) with the decrease in size of AC from 20 to 40 mesh (863 mm) to SPAC (~1.0 mm). Furthermore, the diffusion resistance of SPAC decreased 17-fold compared with GAC. The ratio of oxalate degradation by surface reaction increased by 57%. The rate of transformation of ozone to radicals by SPAC was 330 times that of GAC. The results suggest that a series of changes stimulated by ball milling, including a larger ratio of external surface area, less diffusion resistance, significant surface reaction and potential oxidized surface all contributed to enhancing catalytic ozonation performance. This study demonstrated that SPAC is a simple and effective catalyst for enhancing catalytic ozonation efficacy.
Conventional biological removal of nitrogen and phosphorus is usually limited due to the lack of biodegradable carbon source, therefore, new methods are needed. In this study, a new alternative consisting of enhanced biological phosphorus removal (EBPR) followed by partial nitritationanammox (PN/A), is proposed to enhance nutrients removal from municipal wastewater. Research was carried out in a laboratory-scale system of combined two sequencing batch reactors (SBRs). In SBR1, phosphorus removal was achieved under an alternating anaerobic-aerobic condition and ammonium concentration stayed the same since nitrifiers were washed out from the reactor under short sludge retention time of 2–3 d. The remaining ammonium was further treated in SBR2 where PN/A was established by inoculation. A maximum of nitrogen removal rate of 0.12 kg N?m–3?d–1 was finally achieved. During the stable period, effluent concentrations of total phosphorus and total nitrogen were 0.25 and 10.8 mg?L–1, respectively. This study suggests EBPR-PN/A process is feasible to enhance nutrients removal from municipal wastewater of low influent carbon source.
