Comparison of PM2.5 and PM10 in A Suburban Area in Korea During April, 2003

Airborne particulate matter (PM) concentrations were measured in Iksan, a suburban area in South Korea during April, 2003. PM_2.5 (particles with an aerodynamic diameter less than 2.5 μm) and PM₁₀ (particles with an aerodynamic diameter less than 10 μm) samples were collected, and the chemical characteristics of particles were examined for diurnal patterns, yellow dust/rainfall influences, and scavenging effects. Average concentrations of PM_2.5 and PM₁₀ mass measured were 37.3 ± 16.2 μg m⁻³ and 60.8 ± 29.5 μg m⁻³, respectively. The sum of ionic chemical species concentrations for PM_2.5 and PM₁₀ was 16.9 ± 7.3 and 23.1 ± 10.1 μg/m³, respectively. A significant reduction in PM mass concentrations during rainfall days was observed for coarse mode (PM_{2.5 − 10}) particles, but less reduction was found for fine (PM_2.5) mass concentration. SO₄ ²⁻, NH₄ ⁺, and K⁺ predominated in fine particulate mode, NO₃ ⁻ and Cl⁻ predominated in fine particle mode and coarse particle mode, but Na⁺, Mg²⁺, and Ca²⁺ mostly existed in coarse mode. The high concentration of ammonium due to local emissions and long-range transport neutralized sulfate and nitrate to ammonium sulfate and ammonium nitrate, which were major forms of airborne PM in Iksan. Average mass concentrations of PM₁₀ in daytime and at night were 57.6 and 70.0 μg m⁻³, and those of PM_2.5 were 35.4 and 42.5 μg m⁻³, respectively. NO₃ ⁻ and Cl⁻ in both PM_2.5 and PM₁₀ were about double at night than in the daytime, while the rest of the chemical species were equal or a little higher at night than in the daytime. The results suggest the formation of ammonium nitrate and chloride when high ammonia concentration and low air temperature are allowed. Backward air trajectory analyses showed that air masses arriving at the site during yellow dust period were transported from arid Chinese regions, which resulted in high concentrations of airborne PM mass concentrations. In the meantime, air mass trajectories during a rainfall period were mostly from the Pacific Ocean or the East China Sea, along with a relatively low PM concentration.     

PM<Subscript>10</Subscript> and Ultrafine Particles Counts In-Vehicle and On-Road in the Athens Area

This work presents the first results of a study concerning on-road and in-vehicle exposure to particulate matter in the area of Athens. PM₁₀ concentration measurements were conducted by TSI DustTrak, while driving along routes with different characteristics of traffic density, during September 2003–March 2004. Concurrent measurements of the ultrafine particles (UFPs) number concentration were also conducted, by condensation particle counter during part of the days. Pedestrian exposure to PM₁₀ and UFPs was also studied through stationary measurements on the kerbside of selected roads on November 2003 and February 2004. A major avenue, a heavy-trafficked road across a children hospital and two central roads, one in a residential and one in a commercial area were selected for measurement. The results indicate that every day commuters are exposed to significant concentration levels. Higher exposures were observed in heavy-trafficked areas and during rush hours. Mean PM₁₀ in-vehicle and on-road concentrations ranged from 30–320 μg/m³ and 70–285 μg/m³, respectively. The ultrafine particles number concentrations were in the range of 5.0 × 10⁴–17.3 × 10⁴ particles/cm³ in-vehicle and 3.1 × 10⁴–7.3 × 10⁴ particles/cm³ on the kerbside of a central residential road. Both PM₁₀ and UFPs concentrations presented repeated short-term peak exposures. The results clearly point out the importance of the road microenvironment (in-vehicle and on kerbside) for population exposure in urban areas.     

Characteristics of air pollution in Beijing during sand-dust storm periods

In the Beijing area, March and April have the highest frequency of sand-dust weather. Floating dust, blowing sand, and dust storms, primarily from Mongolia, account for 71%, 20%, and 9% of sand-dust weather, respectively. Ambient air monitoring and analysis of recent meteorological data from Beijing sand-dust storm periods revealed that PM₁₀ mass concentrations during dust storm events remained at 1500 μg m⁻³, which is five to ten times higher than during non-dust storm periods, for fourteen hours on both April 6 and 25, 2000. During the same period, the concentrations in urban areas were comparable to those in suburban areas, while the concentrations of gaseous pollutants, such as SO₂, NO _x , NO₂, and O₃, remained at low levels, owing to strong winds. Furthermore, during sand-dust storm periods, aerosols were created that consisted not only of many coarse particles, but also of a large quantity of fine particles. The PM_2.5 concentration was approximately 230 μg m⁻³, accounting for 28% of the total PM₁₀ mass concentration. Crustal elements accounted for 60–70% of the chemical composition of PM_2.5, and sulfate and nitrate for much less, unlike the chemical composition of PM_2.5 on pollution days, which was primarily composed of sulfates, nitrates, and organic material. Although the very large particle specific surface area provided by dust storms would normally be conducive to heterogeneous reactions, the conversion rate from SO₂ to SO₄ ²⁻ was very low, because the relative humidity, less than 30%, was not high enough.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Indoor Air Quality at Rural and Urban Sites in Pakistan

In the developing world, the vast majority of people rely on solid biomass fuels for cooking and heating which results in poor indoor air quality. The present study determined indoor air quality in some rural and urban areas of Pakistan. Measurements were made of particulate mass (PM10, PM2.5 and PM1), number concentration and bioaerosols in different micro environments. PM10 concentrations of up to 8,555 μg/m³ were observed inside the kitchens where biofuels were used as energy source. Cleaning and smoking was identified as a major source of indoor particulate pollution and concentrations of more than more than 2,000 μg/m³ were recorded in the living room during these activities. Indoor number concentrations in Lahore were typically greater than those observed outdoors in European cites. At a rural site the highest Colony Forming Units (CFUs) were in the 0.5 μm–2 μm size fraction, while at the urban location CFUs were dominant for 2 μm–16 μm. It was observed that CFUs(Colony Forming Units) counts were higher inside living rooms than kitchens. It is important to note that women and children were exposed to extremely high levels of particulates during cooking. Overall, indoor air quality in Pakistan was poor and there is a dire need to take a serious step to combat with it.     

Sources and Variability of Indoor and Outdoor Gaseous Aerosol Precursors (O3, NOx and VOCs)

Measurements of indoor and outdoor aerosol concentrations and their gaseous precursors (O₃, NO and NO₂) as well as volatile organic compounds (VOCs) concentrations were performed at two houses in the Oslo metropolitan area. The variability of the concentration of gaseous compounds was studied in respect to their sources in the indoor and outdoor environments. Domestic heating during the winter and photochemical production during the summer were the main sources for outdoor NOx and O₃. In the indoor environment infiltration of outdoor air, candle burning, smoking and indoor chemical reactions were the main sources affecting their concentrations. The concentrations of VOCs outdoors were enhanced during the summer due to biogenic emissions whereas in the indoor environment their values were affected mostly by emissions from materials used during the recent refurbishing of the houses (>0.4 mg/m³).     

Identification,Abundance and Origin of Aliphatic Hydrocarbons in the Fine Atmospheric Particulate Matter of Athens,Greece

The organic chemical composition of the fine fraction of atmospheric particulate matter in Athens has been studied, in order to establish emission sources. The results of the analyses of the aliphatic fraction indicate that all samples contain n-alkanes ranging from C₁₄ to C₃₂, with C₂₅, C₂₆, C₂₇ and C₂₉ being the more abundant congeners. Fossil fuels biomarkers such as extended tricyclic terpanes (hopanes, steranes) and isoprenoid hydrocarbons (pristane, phytane) were observed in our samples on a daily basis. Source reconciliation was conducted using molecular diagnostic ratios (such as the carbon preference index – CPI). The mean CPI value (1.84) indicates the mixed origin of the Athenian fine particles. The notable presence of an unresolved complex mixture or “hump” of hydrocarbons in our gas chromatograms is indicative of petrogenic hydrocarbon inputs. An approximate measure of this kind of contamination is the ratio of the concentrations of unresolved components to the resolved n-alkanes and other major compounds (U:R). The high U:R value of 25.25 further confirmed the major contribution of fossil fuels. Yet, the percent contribution of leaf wax n-alkanes (25.15%) indicated the parallel contribution of biogenic sources. This work supports the conclusion that vehicular emissions were the major source of aliphatic organic compounds with a smaller contribution of biogenic n-alkanes during the study period in Athens.     

On East Asian Sand and Duststorms and Associated Significant Dustfall Observed from January to May 2001

Monitoring of dust pollution at the western shore of Tae-ahn Peninsula (TAP) and in the Chongju area of central Korea was carried out from January to May 2001. It was found that in Koreathere were 9 cases of sand and duststorms (DS) and 16 associatedsignificant dustfall (SD) days. Observed maximum concentrations of DS and SD coming from NW China and Mongolia were in the rangeof 300–920 for TSP, 200–690 for PM₁₀ and 100–170 g m^-3 for PM_2.5.Satellite measurements clearly showed the formation and subsequent movement of DS to the Korean Peninsula and onward to the Korea East Sea, Japan and the Gulf of Alaska. According to satellite image analysis of dust clouds there were abundant coarse particles, measuring in size of 11.0 m. Medium-sizedparticles measuring in the range of 3.5–7.0 were also prevalent,while fine particles of less than 2.0 m were less distinctive in reflectivity. Measured values of PM_2.5 were alsorelatively low with SD events.The measured average pH values of dusty precipitation associatedwith DS were 7.24. Alkaline precipitation can play a `temporary'role in the neutralization of acidified soil until the subsequentevent of acidic rain. The new selection criteria of SD days from PM_2.5 at 85 g m^-3, PM₁₀ 190 g m^-3 and TSP 250 g m^-3 are recommended on dust pollution occurring from the invasion of a DS elsewhere.     

Effects of Nitrogen Supply on the Sensitivity to O3 of Growth and Photosynthesis of Japanese Beech (Fagus crenata) Seedlings

To obtain basic information for evaluating critical levels of O₃ under different nitrogen loads for protecting Japanese beech forests, two-year-old seedlings of Fagus crenata Blume were grown in potted andisol supplied with N as NH₄NO₃ solution at 0, 20 or 50 kg ha⁻¹ year⁻¹ and exposed to charcoal-filtered air or O₃ at 1.0, 1.5 and 2.0 times the ambient concentration from 16 April to 22 September 2004. The O₃ induced significant reductions in the whole-plant dry mass, net photosynthetic rate at 380 μmol mol⁻¹ CO₂ (A ₃₈₀), carboxylation efficiency (CE) and concentrations of ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) and total soluble protein (TSP) in the leaves. The concentrations of Rubisco and TSP were negatively correlated with the concentration of leaf acidic amino acid, suggesting that O₃ enhanced the degradation of protein such as Rubisco. The N supply to the soil did not significantly change the whole-plant dry mass and A ₃₈₀, whereas it significantly increased the CE and concentrations of Rubisco and total amino acid. No significant interactive effects of O₃ and N supply to the soil were detected on the growth, photosynthetic parameters and concentrations of protein and amino acid in the leaves. In conclusion, N supply to the soil at ≤50 kg ha⁻¹ year⁻¹ does not significantly change the sensitivity to O₃ of growth and net photosynthesis of Fagus crenata seedlings.     

Co-gasification of wood and polyethylene with the aim of CO and H2 production

This article describes the gasification of polyethylene–wood mixtures to form syngas (H₂ and CO) with the aim of feedstock recycling via direct fermentation of syngas to ethanol. The aim was to determine the effects of four process parameters on process properties that give insight into the efficiency of gasification in general, and particularly into the optimum gasification conditions for the production of ethanol by fermentation of producer gas. Gasification experiments (fluidized bed, 800°–950°C) were done under different conditions to optimize the composition of syngas suitable for fermentation purposes. The data obtained were used for statistical analysis and modeling. In this way, the effect of each parameter on the process properties was determined and the model was used to predict the optimum gasification conditions. The parameters varied during the experiment were gasification temperature, equivalence ratio, the ratio of plastic to wood in the feed, and the amount of steam added to the process. The response models obtained proved to be statistically significant in the experimental domain. The optimum gasification conditions for maximization of carbon monoxide and hydrogen production were identified. The conditions are: temperature 900°C, equivalence ratio 0.15, amount of plastic in the feed 0.11 g/g feed, and amount of steam added 0.42 g/g feed. These optimum conditions are at the edge of the present experimental domain. The maximum combined CO and H₂ efficiency was 42%, and for the maximum yield of CO and H₂ it is necessary to minimize the polyethylene content, minimize the added steam and the equivalence ratio, and maximize temperature.     

Polyethylene conversion by partial oxidation in supercritical water

This paper gives the results of partial oxidation experiments of polyethylene (PE) in supercritical water (SCW). The experiments were carried out at a reaction temperature of 693K and a reaction time of 30 min using 6 cm³ of a batch-type reactor. The loaded sample weight was 0.3 g and there was 2.52 g water (0.42 g/cm³). The ratio of oxygen atoms to carbon atoms was 0.3. The results show a significant CO formation in O₂–SCW, and the 1-alkene/n-alkane ratio in partial oxidation was higher than that in SCW pyrolysis. These results suggest the possibility of the hydrogenation of hydrocarbon through partial oxidation followed by a water–gas shift reaction. Received: July 19, 2000 / Accepted: September 28, 2000     

Comparison of Surface Organic Compound Mass Spectrum Patterns by LD-TOFMS for Megalopolis Atmospheric Particles and Diesel Exhaust Particles (DEP)

PM_2.5 and PM₁₀ samples for megalopolis atmospheric particles were collected at Shinjuku, Tokyo in December 1998–January 1999 and August 1999, for two weeks both in winter and summer, with a 24 hr sampling interval. Sampling of PM_2.5 and PM₁₀ in diesel exhaust particles (DEP) was carried out using an automobile exhaust testing system, with a diesel truck placed on a chassis dynamometer. Sampling conditions included idling, constant speed of 40 km hr^-1, M-15 test pattern and 60%-revolution/40%-load of maximum power. Mass spectrums of organic compounds adhering to the surface of the PM_2.5 and PM₁₀ samples were analyzed by laser desorption time-of-flight mass spectrometry (LD-TOFMS, analytical mass range: m/z 1–m/z 380 000). LD-TOFMS analysis of those samples revealed consistently the detection of low-mass organic compounds up to m/z 800. For the megalopolis atmospheric particles, the mass spectrum pattern of wintertime samples was almost the same as that of the summertime samples for both PM_2.5 and PM₁₀. The major peak was m/z 177, and the minor peaks were m/z 84, 94, 101, 163, 189 and 235. The mass spectrum pattern of DEP was the same for all samples under all test conditions. The major peak was m/z 101, and other detected peaks were small.     

Long Term Trends in Concentration of Major Pollutants (SO<Subscript>2</Subscript>, CO,NO, NO<Subscript>2</Subscript>, O<Subscript>3</Subscript> and PM<Subscript>10</Subscript>) in Prague – Czech Republic (Analysis of Data Between 1992 and 2005)

To assess the effect of changes in traffic density and fuels used for heating at the beginning of the 1990s, 1992–2005 monthly averages of PM₁₀, SO₂, NO₂, NO, CO and O₃ from Prague, the Czech capital, were analyzed together with long term trends in emissions of major pollutants, fuel consumption and number of vehicles registered in Prague. The data from all monitoring stations were retrieved from the database of the state automated monitoring system. Correlation coefficients between ambient monthly averaged temperature and all pollutants of concern showed distinct seasonal trends. The results showed that while SO₂ and to some extent also CO concentrations dropped namely in the first half of the analyzed period (1992–1997) as a result decreased fossil fuel consumption for local heating, the behaviour of other pollutant concentrations followed a different pattern. PM₁₀ concentrations decreased during the beginning of the 1990s but showed a sign of increase after 2000. Concentrations of ozone and NO₂ did not reveal any significant change throughout the whole studied period. It can be concluded that during the studied period traditional urban sources of pollution, such as coal and oil combustion, lost their importance but were simultaneously substituted by pollutants from automotive transport (namely PM and NO₂) making the problem of air quality even worse.     

The Role of Catalyst Properties on Methanol Oxidation over V2O5–TiO2 Using Ozone

Oxidation of methanol over V₂O₅ catalysts supported on anatase TiO₂ that were prepared using sol-gel formation and impregnation procedures were investigated. The effects of incorporating Mg in sol-gel to influence the properties of the catalyst were also studied. The process provides an alternative low temperature reaction pathway for reducing emissions of hazardous air pollutant (HAPs) such as methanol and total reduced sulfur compounds (TRS) from pulp and paper mills. The bulk and surface composition of the catalysts were determined by XRD and SEM-EDAX, respectively. The X-ray diffraction patterns of the vanadia–titania catalysts showed mainly the anatase phase of TiO₂. Temperature programmed desorption of methanol from the different catalyst showed that the α and β peaks differ significantly with V content and addition of Mg. The combination of gas phase and surface reactions on the V/TiO₂ catalysts reduced the amount of ozone required for high degradation of methanol to mainly CO _x with small quantities of methyl formate. In the absence of ozone the catalysts showed very low activity. It is hypothesized that the ozone is directly influencing the V⁴⁺ and V⁵⁺ redox cycle of the catalyst. Oxidation of methanol is influenced by the operation variables and catalyst properties. The results of this study revealed that the V content has significant influence on the catalyst activity, and the optimum vanadia loading of about 6 wt%. Higher turnover frequencies were observed over sol-gel catalysts than with catalysts prepared by the impregnation method.     

Comparison of Four Machine Learning Methods for Predicting PM10 Concentrations in Helsinki, Finland

Machine learning methods can offer a practicalalternative to deterministic and statistical methods forpredicting air pollution concentrations. However, for agiven data set, it is often not clear beforehand whichmachine learning method will yield the best predictionperformance. This study compares the variable selection andprediction performance of four machine-learning methods ofdifferent complexity: logistic regression, decision tree,multivariate adaptive regression splines and neuralnetwork. The methods are applied to the task of predictingthe exceedance of the European PM₁₀ daily averageobjective of 50 g m^-3 for a station in Helsinki,Finland. Our study shows that some predictors were selectedby all models but that the different models also pickeddifferent variables. The performance of three of the fourmethods investigated was very similar, however, performanceof the decision tree method was significantly inferior.Performance was sensitive to the learning sample size andtime period used.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Indoor Air Quality Assessment of Elementary Schools in Curitiba, Brazil

The promotion of good indoor air quality in schools is of particular public concern for two main reasons: (1) school-age children spend at least 30% of their time inside classrooms and (2) indoor air quality in urban areas is substantially influenced by the outdoor pollutants, exposing tenants to potentially toxic substances. Two schools in Curitiba, Brazil, were selected to characterize the gaseous compounds indoor and outdoor of the classrooms. The concentrations of benzene, toluene, ethylbenzene, and the isomers xylenes (BTEX); NO₂; SO₂; O₃; acetic acid (HAc); and formic acid (HFor) were assessed using passive diffusion tubes. BTEX were analyzed by gas chromatography–ion trap mass spectrometry and other collected gasses by ion chromatography. The concentration of NO₂ varied between 9.5 and 23?µg m^?3, whereas SO₂ showed an interval from 0.1 to 4.8?µg m^?3. Within the schools, BTEX concentrations were predominant. Formic and acetic acids inside the classrooms revealed intermediate concentrations of 1.5?µg m^?3 and 1.2?µg m^?3, respectively.     

Increase of Ozone Concentration in an Inland Basin During the Period of Nocturnal Thermal High

Since ground level ozone concentrations in the basin on one day before the occurrence of unusually high air temperature with nocturnal thermal high showed a typical urban type of a maximum ozone concentration at 1300 LST and a minimum at night. However, a maximum ozone concentration under extremely high air temperature of 39.2 °C was detected at 1700 LST or 1800 LST at two environmental monitoring sites, which was 4 or 5 hr delayed from the typical occurrence time, 1300 LST. Its maximum value showed about 50 or 70% increase of the concentration more than the typical maximum value and its concentration gradually decreased until 2100 LST. After 1200 LST until 1800 LST, air temperature was maintained over 35 °C and the high temperature made a great contribution to the increase of O₃ for several hours. The deviated occurrence time of a maximum ozone concentration is mainly attributed to meteorological and topographic effects – shifted occurrence time of maximum air temperature, shrunken atmospheric boundary layer depth and wind. While daytime O₃ concentration due to photochemical production of O₃ from NO₂ increased, NO₂ concentration decreased, with their reverse respondent patterns each night. A secondary maximum concentration of O₃ at 2300 LST or 2400 LST is due to a much shallower depth of nocturnal surface inversion layer with daytime producing more O₃ than that of the daytime convective boundary layer, resulting in the increase of ozone concentration, though the reduction of ozone occurred under the reversal process of O₃ into NO₂.     

Can Nutrient Spiralling be Used to Detect Seasonal Nutrient Uptake in a Forested Stream?

Nutrient spiralling measurements were conducted in Lyrebird Creek, a forested stream in the Dandenong Ranges, Victoria, Australia. Spiralling indices from several nutrient (, ) enrichment experiments were correlated with seasonal variation in factors thought to control nutrient uptake, i.e., temperature, light and algal biomass. It was hypothesized that nutrient uptake would be higher in summer as increased temperatures would promote both biotic and abiotic processes and higher light levels in summer would stimulate photosynthesis. However, results did not support this hypothesis. Uptake length for and and uptake velocity were not correlated with chlorophyll-a, light or temperature (r ² < 0.30, P > 0.1) despite the seasonality of these biophysical factors (r ² > 0.42, P < 0.02). Lyrebird Creek might had no seasonal trend in nutrient uptake and/or nutrient spiraling measurements only appears suitable for contrasting streams with large differences in biophysical factors that supports biotic and abiotic nutrient processing. In addition, small errors in measuring a nutrient concentration can result in a large range in the estimated S _w and increased difficulty in determining significant differences in nutrient spiralling indices.