不同类型海岸的溢油清理方法

世界石油资源分布和需求的不均衡性,促进了海上石油工业和石油运输业的快速发展,同时也增加了溢油事故的几率.海上溢油污染问题日趋严重,溢油污染对海洋环境、生态、资源、经济及人类生产生活等造成了巨大的影响,日益引起社会各界的关注.海岸溢油污染清理实践表明,正确的溢油清理方案的制定应综合考虑海岸的敏感性指数、溢油的类型、清理方法可能带来的危害以及支际可操作程度等.对包括盐沼地海岸和红树林海岸,沉积海岸,以及岩石海岸三类典型海岸的国内外现有海岸溢油污染清理技术进行了详细的综述,以期为我国的海岸带管理和溢油应急计划的制订提供技术参考.     

A review on submarine oil and gas leakage in near field: droplets and plume

The 2010 Deepwater Horizon spill remains the largest catastrophic release of oil and gas into the deep sea. The irrupted oil and gas substantially impact a marine ecosystem, cause human injury, and have high societal opinions. Therefore, understanding the transport and dispersion of subsurface hydrocarbon provides an imperative substratum for the practical assessment and response of marine oil spill accidents. In this review, we summarize the major advances since the Deepwater Horizon accident, with emphasis on the observation and modeling of the droplet and the formation and dynamics of the plume. Additional complexity including more than the investigation of gas-saturated oil at high-pressure and the effect of Earth’s rotation on near field plume is also outlined. We end with a few outlooks on key priorities for more precisely estimations on future oil spills.

     

Measurement of fluorescence decay of crude oil: a potential technique to identify oil slicks

The single photon counting technique has been used to measure the decay time for several Kuwaiti crude and refined oils. Fluorescent characteristics of two different bunker oils from widely separate geographic areas have been studied. Laser induced fluorescent data for the crude oil samples are compared with the decay time results to evaluate the potential of these techniques for the identification of oil sticks in the marine environment. Response of the oil film thickness to various excitation wavelengths from a CW Ar ion laser and a pulsed xenon lamp has been investigated.     

Gladius and its derivatives as potential biosorbents for marine diesel oil

The demand for low cost and effective materials to remove contaminants such as residues of oil spills has encouraged studies on new biosorbents produced from wastes. Considering the overgeneration of fishing residues and the necessity to provide an alternative purpose for such materials, this study aimed to evaluate squid gladius and its derivatives (β-chitin and chitosan) as sorbents to remove marine diesel oil (MDO) from fresh and artificial seawater. It was also executed an attempted to improve their performances through a high-intensity ultrasound treatment (UT-gladius and UT-β-chitin). All sorbents removed MDO at both salinities. Contact surface area, salinity, and water retention seemed to play a key role in the outcomes. UT-β-chitin’s performance was significantly superior to β-chitin’s and chitosan’s in MDO removal at salinity 0, as well as at salinity 30, where gladius and UT-gladius also excelled. Ultrasound treatment improved the oil removal performance of UT-β-chitin by increasing its contact surface area. This is the first report on the efficiency of gladius and UT-β-chitin for such purpose, and brought up huge possibilities and new questions that can lead to the achievement of biosorbents of great efficiency.     

The Threats from Oil Spills: Now, Then, and in the Future

The ongoing oil spill from the blown-out well by the name of Macondo, drilled by the ill-fated rig Deepwater Horizon, has many features in common with another blowout in the Mexican Gulf that happened three decades ago. Then the oil gushed out from the Ixtoc I well drilled by the Sedco 135-F semi-submersible rig. In the years between these catastrophes, the source and nature of oil spills have undergone large changes. Huge spills from tankers that ran aground or collided used to be what caught the headlines and caused large ecological damage. The number and size of such accidental spills have decreased significantly. Instead, spills from ageing, ill-maintained or sabotaged pipelines have increased, and places like Arctic Russia, the Niger Delta, and the northwestern Amazon have become sites of reoccurring oil pollution. As for blowouts, there is no clear trend with regard to the number of incidences or amounts of spilled oil, but deepwater blowouts are much harder to cap and thus tend to go on longer and result in the release of larger quantities of oil. Also, oil exploration and extraction is moving into ever-deeper water and into stormier and icier seas, increasing potential risks. The risk for reoccurring spills like the two huge Mexican Gulf ones is eminent and must be reduced.     

Hydrocarbon fuel spill dispersion on water: A literature review

The literature concerning the fate of light hydrocarbon fuel spills on water is reviewed. The review focuses on jet fuels and contains some discussion of gasoline, diesel, marine and kerosene fuel spills. The two major fates of light hydrocarbon spill on water are evaporation and dissolution, although biodegradation, photooxidation and adsorption onto suspended sediments can also be of some importance.     

Oil Identification Based on a Goodness-of-Fit Metric Applied to Hydrocarbon Analysis Results

Assessment of environmental damage following accidental oil spills requires reliable oil identification methods. Results from hydrocarbon analyses of environmental samples are often difficult to interpret, because of the changes in oil composition (or weathering) that follows release into the environment, and because of confounding by hydrocarbons from other sources. To a first-order approximation, weathering proceeds according to simple first-order loss-rate (FOLR) kinetics for polycyclic aromatic hydrocarbons (PAH) based on molecular size. This relationship between relative weathering rate and molecular size can be exploited to infer the initial PAH composition of spilled oils, and this information can be combined with results for weathering-invariant analytes to substantially increase the precision and accuracy of hydrocarbon source recognition methods. The approach presented here evaluates a goodness-of-fit metric between the measured hydrocarbon composition of an environmental sample and a suspected source, after correcting for PAH weathering losses based on FOLR kinetics. Variability from analytical and sampling error may thus be accounted for, and source identifications can be expressed as objective probability statements. This approach is illustrated by application to four independent case studies.     

Oil Identification Based on a Goodness-of-Fit Metric Applied to Hydrocarbon Analysis Results

Assessment of environmental damage following accidental oil spills requires reliable oil identification methods. Results from hydrocarbon analyses of environmental samples are often difficult to interpret, because of the changes in oil composition (or weathering) that follows release into the environment, and because of confounding by hydrocarbons from other sources. To a first-order approximation, weathering proceeds according to simple first-order loss-rate (FOLR) kinetics for polycyclic aromatic hydrocarbons (PAH) based on molecular size. This relationship between relative weathering rate and molecular size can be exploited to infer the initial PAH composition of spilled oils, and this information can be combined with results for weathering-invariant analytes to substantially increase the precision and accuracy of hydrocarbon source recognition methods. The approach presented here evaluates a goodness-of-fit metric between the measured hydrocarbon composition of an environmental sample and a suspected source, after correcting for PAR weathering losses based on FOLR kinetics. Variability from analytical and sampling error may thus be accounted for, and source identifications can be expressed as objective probability statements. This approach is illustrated by application to four independent case studies.     

Pattern Recognition Based Software for Oil Spills Identification by Gas-Chromatography and IR Spectrophotometry

For environmental control purposes, floating oil spills in harbours, off shore areas and their sources must often be identified. Pattern recognition, applied to JR spectrophotometric data (600-2000 cm m 1 range), and to chromatographic data ( n -alkanes) for the spill and various suspected sources such as oil and fuels from ships bunkers and harbour installations, can lead to definite conclusions; particularly after artificial weathering formula are used. The software application provides quick and accurate identification of the pollution source. The identification algorithm has a learning stage in which the user creates a minimal database. This database has a tree structure with classes (fuels, crude, etc.) and members representing samples from already known sources. A sample contains JR and chromatographic data and information of the originating source. A larger database means more knowledge, which conveys a better identification. When the origin of an unknown sample is searched for, the software looks for the best match through the database and displays the results in two lists; sorted by calculated similarity. One list displays the classes in which the unknown sample could be included and the other displays the possible sources. An extra check can be done by visual inspection of the overlapped graphics (unknown sample and each of the identified sources).     

Accidental Versus Operational Oil Spills from Shipping in the Baltic Sea: Risk Governance and Management Strategies

Marine governance of oil transportation is complex. Due to difficulties in effectively monitoring procedures on vessels en voyage, incentives to save costs by not following established regulations on issues such as cleaning of tanks, crew size, and safe navigation may be substantial. The issue of problem structure is placed in focus, that is, to what degree the specific characteristics and complexity of intentional versus accidental oil spill risks affect institutional responses. It is shown that whereas the risk of accidental oil spills primarily has been met by technical requirements on the vessels in combination with Port State control, attempts have been made to curb intentional pollution by for example increased surveillance and smart governance mechanisms such as the No-Special-Fee system. It is suggested that environmental safety could be improved by increased use of smart governance mechanisms tightly adapted to key actors’ incentives to alter behavior in preferable directions.     

Assessment of crude oil biodegradation in arctic seashore sediments: effects of temperature,salinity, and crude oil concentration

The expected increase in offshore oil exploration and production in the Arctic may lead to crude oil spills along arctic shorelines. To evaluate the potential effectiveness of bioremediation to treat such spills, oil spill bioremediation in arctic sediments was simulated in laboratory microcosms containing beach sediments from Barrow (Alaska), spiked with North Slope Crude, and incubated at varying temperatures and salinities. Biodegradation was measured via respiration rates (CO₂ production); volatilization was quantified by gas chromatography/mass spectrophotometry (GC/MS) analysis of hydrocarbons sorbed to activated carbon, and hydrocarbons remaining in the sediment were quantified by GC/flame ionization detector (FID). Higher temperature leads to increased biodegradation by naturally occurring microorganisms, while the release of volatile organic compounds was similar at both temperatures. Increased salinity had a small positive impact on crude oil removal. At higher crude oil dosages, volatilization increased, however CO₂ production did not. While only a small percentage of crude oil was completely biodegraded, a larger percentage was volatilized within 6–9 weeks.     

Treatment of oil spill by sorption technique using fatty acid grafted sawdust

Treatment of oil spills remains a challenge to environmental scientists and technologists. Among all the existing techniques used for oil treatment, sorption is a popular technique because it is cheap, simple and effective. Among the various sorbents used, sawdust appears to be the most attractive material in terms of cost, versatility and abundance. In the present work, the efficacy of surface modification of sawdust by fatty acids (oleic acid, stearic acid and decanoic acid) and vegetable oils (castor oil or mustard oil) is demonstrated. Sorption of seawater contaminated with crude oil and also weathered oil was greatly enhanced by the surface modification. The results show that oleic acid grafted sawdust (OGSD) has the best sorption capacity for crude oil as well as weathered oil.     

Investigation of evaporation and biodegradation of fuel spills in Antarctica: II-extent of natural attenuation at Casey Station

In many temperate regions, fuel and oil spills are sometimes managed simply by allowing natural degradation to occur, while monitoring soils and groundwater to ensure that there is no off-site migration or on-site impact. To critically assess whether this approach is suitable for coastal Antarctic sites, we investigated the extent of evaporation and biodegradation at three old fuel spills at Casey Station. Where the contaminants migrated across frozen ground, probably beneath snow, approximately half the fuel evaporated in the first few months prior to infiltration at the beginning of summer. Once in the ground, however, evaporation rates were negligible. In contrast, minor spills from fuel drums buried in an abandoned waste disposal site did not evaporate to the same extent. Biodegradation within all three spill sites is generally very minor. We conclude that natural attenuation is not a suitable management strategy for fuel-contaminated soils in Antarctic coastal regions.     

Removal by sorption and in situ biodegradation of oil spills limits damage to marine biota: a laboratory simulation

This study examined the efficiency of cotton grass fibers in removing diesel oil from the surface of water in conditions prevailing in the Baltic Sea. The effect of low temperature, salinity, and bacterial amendments were tested in laboratory-scale set-ups, whereas 600-L mesocosms filled with Baltic Sea water were used for testing the effects of diesel oil and rapid removal of the oil on microorganisms, phytoplankton, and mussels. Cotton grass proved to be an excellent sorbent for diesel oil from the water surface at a low temperature. Inoculation with diesel-enriched microorganisms enhanced degradation of oil significantly in laboratory-scale experiments. In mesocosm experiments, the addition of diesel oil (0.66 mg L(-1), 0.533 L m(-2)) to the basins resulted in higher microbial density than in all other basins, including inoculated ones, suggesting that the Baltic Sea contains indigenous hydrocarbon degraders. The removal of oil with cotton grass significantly improved the survival of mussels in the mesocosm tests: 100% mortality in diesel basins versus 0% mortality in basins with cotton grass, respectively. However, the surviving mussels suffered from histopathological changes such as inflammatory responses, degenerations, and cell death. The observed rescuing effect was observable even when the cotton grass-bound oil was left in the water. The results underline the importance of rapid action in limiting damage caused by oil spills.     

Pattern Recognition Based Software for Oil Spills Identification by Gas-Chromatography and IR Spectrophotometry

For environmental control purposes, floating oil spills in harbours, off shore areas and their sources must often be identified. Pattern recognition, applied to IR spectrophotometric data (600–2000 cm⁻¹ range), and to chromatographic data (n -alkanes) for the spill and various suspected sources such as oil and fuels from ships bunkers and harbour installations, can lead to definite conclusions; particularly after artificial weathering formula are used. The software application provides quick and accurate identification of the pollution source. The identification algorithm has a learning stage in which the user creates a minimal database. This database has a tree structure with classes (fuels, crude, etc.) and members representing samples from already known sources. A sample contains IR and chromatographic data and information of the originating source. A larger database means more knowledge, which conveys a better identification. When the origin of an unknown sample is searched for, the software looks for the best match through the database and displays the results in two lists; sorted by calculated similarity. One list displays the classes in which the unknown sample could be included and the other displays the possible sources. An extra check can be done by visual inspection of the overlapped graphics (unknown sample and each of the identified sources).     

Econometric modelling, estimation and policy analysis of oil spill processes

This paper explores approaches to model specification suitable for empirical investigation of a stochastic oil spill model. We focus on the effects of economic incentive measures on the frequency of oil spills, spill size, and volume of oil spilled. We look into the relationships between parameters that describe the spill generation process and the enforcement effort, using data for the Black and Baltic Seas.     

Comparative toxicity assessment of in situ burn residues to initial and dispersed heavy fuel oil using zebrafish embryos as test organisms

Environmental Science and Pollution Research - In situ burning (ISB) is discussed to be one of the most suitable response strategies to combat oil spills in extreme conditions. After burning, a...     

Sediment-associated aliphatic and aromatic hydrocarbons in coastal British Columbia, Canada: concentrations, composition, and associated risks to protected sea otters

Sediment-associated hydrocarbons can pose a risk to wildlife that rely on benthic marine food webs. We measured hydrocarbons in sediments from the habitat of protected sea otters in coastal British Columbia, Canada. Alkane concentrations were dominated by higher odd-chain n-alkanes at all sites, indicating terrestrial plant inputs. While remote sites were dominated by petrogenic polycyclic aromatic hydrocarbons (PAHs), small harbour sites within sea otter habitat and sites from an urban reference area reflected weathered petroleum and biomass and fossil fuel combustion. The partitioning of hydrocarbons between sediments and adjacent food webs provides an important exposure route for sea otters, as they consume ∼25% of their body weight per day in benthic invertebrates. Thus, exceedences of PAH sediment quality guidelines designed to protect aquatic biota at 20% of the sites in sea otter habitat suggest that sea otters are vulnerable to hydrocarbon contamination even in the absence of catastrophic oil spills.     

A Lagrangian analysis of the gravity-inertial oil spreading on the calm sea using the reflective oil-water interface treatment

Environmental Science and Pollution Research - Negative impacts are caused by oil spills on coastal ecosystems. In the phenomenon of oil spreading, the knowledge of the physical properties of the...     

Ambient air concentrations exceeded health-based standards for fine particulate matter and benzene during the Deepwater Horizon oil spill

The Deepwater Horizon oil spill is considered one of the largest marine oil spills in the history of the United States. Air emissions associated with the oil spill caused concern among residents of Southeast Louisiana. The purpose of this study was to assess ambient concentrations of benzene (n=3,887) and fine particulate matter (n=102,682) during the oil spill and to evaluate potential exposure disparities in the region. Benzene and fine particulate matter (PM2.5) concentrations in the targeted parishes were generally higher following the oil spill, as expected. Benzene concentrations reached 2 to 19 times higher than background, and daily exceedances of PM2.5 were 10 to 45 times higher than background. Both benzene and PM2.5 concentrations were considered high enough to exceed public health criteria, with measurable exposure disparities in the coastal areas closer to the spill and clean-up activities. These findings raise questions about public disclosure of environmental health risks associated with the oil spill. The findings also provide a science-based rationale for establishing health-based action levels in future disasters.

Implications: Benzene and particulate matter monitoring during the Deepwater Horizon oil spill revealed that ambient air quality was a likely threat to public health and that residents in coastal Louisiana experienced significantly greater exposures than urban residents. Threshold air pollution levels established for the oil spill apparently were not used as a basis for informing the public about these potential health impacts. Also, despite carrying out the most comprehensive air monitoring ever conducted in the region, none of the agencies involved provided integrated analysis of the data or conclusive statements about public health risk. Better information about real-time risk is needed in future environmental disasters.