Organic and inorganic sampling artefacts assessment

During collection on filter-based aerosol samplers, organic and inorganic aerosol compounds both contribute to positive and negative artefacts, significantly affecting chemical analyses results for single species and PM mass concentrations. Up to now, studies on organic or inorganic artefacts have been conducted in Europe but very scarce data are available for both in a single study.The field study was carried out in Milan, which is located in the Po valley (Northern Italy) one of the major pollution hot spots in Europe. As sampling artefacts depend on many factors, such as filter type, face velocity, sampling duration, and ambient conditions, in this field study two different filter types have been considered (i.e. quartz fibre filters and Teflon filters) for the assessment of both inorganic and organic artefacts during two different seasons (performing also some samplings at different flow-rates).Results showed that positive artefacts due to OC adsorption on quartz filters accounted for 39% of the OC measured concentration in summer, and 23% in winter. Negative artefact due to nitrate volatilisation by the filters was 51% on Teflon and 22% on the quartz filters in summer, and no or negligible losses were observed in winter. A significant improvement in the PM mass comparability obtained in parallel samplings on different filters was obtained taking into account the artefact estimates performed in this study.     

advances in particle sampling and measurement

Seventeen papers were presented on improved instruments and techniques for measuring the size, number, and composition of particles in process streams. Recent studies on cascade impactors, cyclones, and diffusion batteries were reported. Several papers discussed methods for making in situ particle size or mass determinations through light scattering. Systems that have been developed to determine the collection efficiency of electrostatic precipitators, scrubbers, and bag filters were described.     

Dicarboxylic acid concentration trends and sampling artifacts

Dicarboxylic acids associated with airborne particulate matter were measured during a summer period in Philadelphia that included multiple air pollution episodes. Samples were collected for two 10 h periods each day using a high-volume sampler with two quartz fiber filters in series, and analyzed by gas chromatography mass spectrometry (GCMS) with diazomethane derivatization. Among the dicarboxylic acids investigated, phthalic acid and adipic acid exhibited the greatest diurnal variations and the strongest linear relationship with maximum daily ozone concentration. Dicarboxylic acids and ozone concentration exhibited a poor linear relationship with organic to elemental carbon ratio. All species investigated were affected by significant sampling artifact errors at low concentrations, but sampling errors were negligible at high concentrations observed during ozone episodes.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

Small-scale variability of metals in soil and composite sampling

Soil pollution data is also strongly scattering at small scale. Sampling of composite samples, therefore, is recommended for pollution assessment. Different statistical methods are available to provide information about the accuracy of the sampling process. Autocorrelation and variogram analysis can be applied to investigate spatial relationships. Analysis of variance is a useful method for homogeneity testing. The main source of the total measurement uncertainty is the uncertainty arising from sampling. The sample mass required for analysis can also be estimated using an analysis of variance. The number of increments to be taken for a composite sample can be estimated by means of simple statistical formulae. Analytical results of composite samples obtained from different fusion procedures of increments can be compared by means of multiple mean comparison. The applicability of statistical methods and their advantages are demonstrated for a case study investigating metals in soil at a very small spatial scale. The paper describes important statistical tools for the quantitative assessment of the sampling process. Detailed results clearly depend on the purpose of sampling, the spatial scale of the object under investigation and the specific case study, and have to be determined for each particular case.     

Odor concentration decay and stability in gas sampling bags

This paper presents results of an experimental study into factors contributing to decay of odor samples during storage, between 4 and 40 hr after sample collection. The odor studied was sampled from a tobacco processing plant as part of collaborative research with a view to establishing a manual outlining methods for odor annoyance management, specifically for the tobacco industry. In August and September 1997, an experimental program was carried out in which two types of tobacco odor were sampled: Burley Toaster and Mix. The dependent variable was odor concentration in the bag, measured by dynamic olfactometry in accordance with the draft Comité Européen de Normalisation (CEN) standard EN13725 "Air Quality-Determination of Odor Concentration by Dynamic Olfactometry." The independent variables were sampling bag material, degree of dilution during sampling, dilution gas used, particle removal during sampling, and age of sample in hours. In the first phase, 94 odor analyses were carried out. In a second test, 32 samples were analyzed for odor concentration. In addition, 16 samples were analyzed using gas chromatography-mass spectrometry (GC-MS). Analysis of the results (analysis of variance) led to the unexpected conclusion that Nalophan film bags performed significantly better than metalized Cali-Bond layered film as a bag material. The odor concentration of samples in Nalophan bags remained relatively stable between 4 and 12 hr after sampling. After 30 hr, decay to about half the initial concentration, as measured at 4 hr, was observed. Particle removal during sampling caused the odor concentration in the bags to be reduced by approximately 20%. For practical reasons, particle removal remains useful, to avoid contamination of equipment. Using air or nitrogen as the neutral gas for pre-dilution during sampling or the dilution factor used (between factor 2 and 6) did not appear to have an effect on the decay characteristic of odor samples. The following recommendations are suggested for the practice of collecting odor samples and apply specifically to tobacco processing emissions: Analyze samples as soon as possible, preferably within 12 hr; When samples age for more than 12 hr, decay is likely to cause a reduction in odor concentration to half the original concentration at age 30 hr; Use sampling bags made of Nalophan NA or benchmark performance of other materials against Nalophan NA before using alternative materials; Use pre-dilution when sampling only for the purpose of avoiding condensation during sample storage. Use an appropriate minimum dilution factor to avoid condensation; Both nitrogen and high-purity (synthetic) air are suitable to use as neutral gas for pre-dilution; and When sampling tobacco odors, use an odorless filter to remove particles. This practice removes a source of variation and avoids contamination of equipment. The effect on results, despite being consistently lower in odor concentration, is not meaningful in terms of perceived intensity or annoyance potential.     

Oxidant denuder sampling for analysis of polycyclic aromatic hydrocarbons and their oxygenated derivates in ambient aerosol: evaluation of sampling artefact

The concentrations of some polycyclic aromatic hydrocarbons (PAH) and oxygenated PAH (O-PAH) can be changed by oxidation reactions during sampling. This can lead to an over- or underestimation of the corresponding adverse health effects. The aim of this study was the evaluation of these sampling artefacts. The potential of using an oxidant denuder was shown by parallel low-volume sampling with and without MnO₂ ozone denuder. Twenty-three PAH and 11 O-PAH in ambient air were analysed, both in the vapour and particulate phase. The denuder was proven to be highly efficient for stripping ozone from air while causing no significant particle losses. In general, the concentrations of 5- to 7-ring PAH, which are predominantly associated with particles, were underestimated in non-denuded samples. The highest losses due to reaction with ozone and other atmospheric oxidants were observed for benzo[a]pyrene and perylene. Concurrently, the concentrations of most of the mainly particle-associated 4- to 5-ring O-PAH were higher in the non-denuded samples. The denuder did not only remove ozone, moreover other gaseous species such as more volatile PAH and O-PAH were partially oxidized on the catalytic surface, too. Degradation of PAH and concurrent degradation/formation reactions of O-PAH occurred. The corresponding reactivities of selected PAH and O-PAH are discussed.     

Development and demonstration of a free surface flow-dependent sampling technology

Statistical assessment of water quality data, obtained at the South Florida Water Management District (West Palm Beach, Florida) S-65E structure, illustrated significant differences and inconsistency in nutrient concentrations (Daas and Ebadian, 2003). The evaluation showed that currently used water sampling techniques are inadequate because of deficiencies in functionality and sensitivity to flow conditions at the structure. Moreover, the study indicated the need for a more precise sampling technology, which would consider variations in the velocity profile across the water column during the sampling process. Therefore, a new prototype sampling technology was designed and tested in a pilot open channel. The new sampler had the capability to collect discrete aliquot volumes of water samples that are proportional to the corresponding point velocity at each of these depths. The discrete aliquot volumes were blended to provide an integrated sample that captures the variations in the velocity profile.     

Distribution of pesticide residues in soil and uncertainty of sampling

Pesticide residues were determined in about 120 soil cores taken randomly from the top 15 cm layer of two sunflower fields about 30 days after preemergence herbicide treatments. Samples were extracted with acetone-ethyl acetate mixture and the residues were determined with GC-TSD. Residues of dimethenamid, pendimethalin, and prometryn ranged from 0.005 to 2.97 mg/kg. Their relative standard deviations (CV) were between 0.66 and 1.13. The relative frequency distributions of residues in soil cores were very similar to those observed in root and tuber vegetables grown in pesticide treated soils. Based on all available information, a typical CV of 1.00 was estimated for pesticide residues in primary soil samples (soil cores). The corresponding expectable relative uncertainty of sampling is 20% when composite samples of size 25 are taken. To obtain a reliable estimate of the average residues in the top 15 cm layer of soil of a field up to 8 independent replicate random samples should be taken. To obtain better estimate of the actual residue level of the sampled filed would be marginal if larger number of samples were taken.     

Simultaneous passive sampling of volatile organic compounds

In this paper, the results obtained in the simultaneous passive sampling of toluene, hexane, methyl ethyl ketone and ethyl acetate on activated charcoal are presented and compared with results obtained when the compounds were tested individually. Any observed deviations in the sampling rate are possibly due to the variations in the adsorption efficiency or in the coefficients of desorption caused by the presence of more than one adsorbate, though in all cases the values obtained are within the accepted margins recommended by NIOSH     

Conditional sampling for measuring mercury vapor fluxes

Surface–atmosphere mercury fluxes are difficult to measure accurately. Current techniques include dynamic flux chambers and micrometeorological gradient and aerodynamic approaches, all of which have a number of intrinsic problems associated with them. We have adapted conditional sampling (relaxed eddy accumulation), a micrometeorological technique commonly used to measure other trace gas fluxes, to measure surface–air mercury fluxes. Our initial flux measurement campaign over an agricultural soil consisted of two 1-week measurement periods, and was longer in duration than previously reported mercury flux measurement periods. Fluxes during both measurement periods ranged between 190.5 (evolution) and –91.7 ng m⁻² h⁻¹ (deposition) with an average evolution of 9.67 ng m⁻² h⁻¹. The data showed significant diurnal trends, weakly correlated with shallow soil temperatures and solar radiation. This initial trial run indicates that conditional sampling has much promise for the accurate quantification of both short and long-term mercury fluxes.     

Influence of air humidity on sampling efficiency of some solid adsorbents used for sampling organics from work-room air

The influence of air humidity on the sampling efficiency of Amberlite XAD porous polymers and activated charcoal was studied by determining the recovery of various organics at 20% and 85% relative humidity. The sampling efficiency of XAD-7 was found to decrease with increasing relative humidity, while the sampling efficiency of XAD-2 and activated charcoal was relatively unaffected for the compounds studied. Activated charcoal had a greater capacity than Amberlite XAD for several types of compounds, however.