Degradation of Isobutanal at High Loading Rates in a Compost Biofilter

Abstract

Biofiltration has been increasingly used for cleaning waste gases, mostly containing low concentrations of odorous compounds. To expand the application area of this technology, the biofiltration of higher pollutant loading rates has to be investigated. This article focuses on the biodegradation of isobutanal (IBAL) in a compost biofilter (BF) at mass loading rates between 211 and 4123 g/m³/day (30– 590 ppm_v). At mass loading rates up to 785 g/m³/day, near 100% removal efficiencies could be obtained. However, after increasing the loading rate to 1500–1900 g/m³/day, the degradation efficiency decreased to 62–98%. In addition, a pH decrease and production of isobutanol (IBOL) and isobutyric acid (IBAC) were observed. This is the first report showing that an aldehyde can act as electron donor as well as acceptor in a BF. To study the effects of pH, compost moisture content, and electron acceptor availability on the biofiltration of IBAL, IBOL, and IBAC, additional batch and continuous experiments were performed. A pH of 5.2 reduced the IBAL degradation rate and inhibited the IBOL degradation, although adaptation of the microorganisms to low pH was observed in the BFs. IBAC was not degraded in the batch experiments. High moisture content (51%) initially had no effect on the IBOL production, although it negatively affected the IBAL elimination increasingly during a 21–day time–course experiment. In batch experiments, the reduction of IBAL to IBOL did not decrease when the amount of available electron acceptors (oxygen or nitrate) was increased. The IBAL removal efficiency at higher loading rates was limited by a combination of nutrient limitation, pH decrease, and dehydration, and the importance of each limiting factor depended on the influent concentration.     

氢自养生物还原去除地下水中对硝基氯苯（p-NCB）的实验研究

采用批式实验讨论了氢自养还原菌在厌氧条件下,利用氢气作为电子供体还原地下水中对硝基氯苯的可行性及其影响因素。结果表明,氢自养菌能利用氢气生物还原对硝基氯苯,并产生中间产物对氯苯胺,继而进一步还原脱氯产生苯胺,该过程可提高对硝基氯苯的可生化性。对硝基氯苯在初始阶段还原速率较快,最高去除速率达到610μg/（L.d）,随后逐渐降低达到稳定。影响因素实验表明,在一定浓度范围内提高对硝基氯苯浓度对其去除率影响较小,但硝基进一步还原和脱氯效果降低;氢自养菌还原硝基氯苯的最适宜pH值在7.0~8.0之间;水中的硝酸盐和对硝基氯苯对电子供体存在竞争,硝酸盐反硝化对对硝基氯苯还原具有抑制作用。     

Thermophilic Toluene Biofiltration

ABSTRACT

Thermophilic biodégradation of toluene with active compost biofilters was studied. Thermophilic conditions were maintained either by daily substrate addition (semicontinuous composting) or with a heating system (batch thermophilic composting). The semicontinuous system was designed for the treatment of cool (less than approximately 35 °C) gases under thermophilic conditions, while the extended batch approach was developed for the treatment of warmer gases. When the semicontinuous system was operated at 50 °C (after a one-day start-up period) at an average inlet concentration of 5.5 g m^-3, toluene was degraded at a rate ranging from 73 to 110 g C m^-3 hr^-1. Batch thermophilic treatment was somewhat less effective at the same inlet concentration. Semicontinuous toluene biofiltration at 60 °C was also investigated, but biodegradation rates were significantly lower than at 50 °C. In all systems, toluene biodegradation was proportional to the inlet concentration. Rates of up to 289 g C m^-3 hr^-1 (at an inlet concentration of 14.7 g m^-3) were achieved for semicontinuous and batch operation and 251 g C m^-3 hr^-1 (at an inlet concentration of 18.4 g m^-3) for batch thermophilic at 50 °C. Semicontinuous thermophilic operation at 60 °C showed a maximum rate of 119 g C m^-3 hr^-1. Active compost ther-mophilic biofiltration was found to be very effective when concentrations are high. At lower concentrations, rates were similar to those obtained with mesophilic biofiltration. Mixing, humidity, and the presence of cosubstrate were important parameters in maintaining high degradation rates. Biofiltration in the batch thermophilic mode could be useful when conventional biofiltration is ineffective due to elevated gas temperatures. Biofiltration in the semicontinuous thermophilic could reduce the biofilter size necessary for treatment of cooler gases containing high concentrations of volatile organic compounds.     

高岭土负载纳米铁镍双金属去除水中偶氮染料直接耐晒黑G

采用液相还原法制备焙烧高岭土负载纳米铁镍双金属（CK-Fe/Ni）。考察了在不同条件下,如pH、投加量、初始浓度、温度等,对负载型纳米铁镍双金属降解水中偶氮染料直接耐晒黑G的影响及动力学研究。结果表明：在pH=9.49、温度为30℃、负载型纳米铁镍双金属的投加量为1.05 g/L、搅拌速度为60 r/min,经过20 min反应后,负载型纳米铁镍双金属降解水中偶氮染料直接耐晒黑G的去除率达到了99.98%。吸附和电镜表征结果表明,作为载体的焙烧高岭土起着吸附直接耐晒黑G和分散纳米铁镍双金属颗粒的作用导致反应活性提高。降解动力学数据表明,负载型纳米铁镍双金属对直接耐晒黑G的降解过程符合伪一级反应动力学规律,速率常数k随负载型纳米铁镍双金属的投加量的增加而提高,表观活化能为19.72 kJ/mol。最后,利用高岭土负载纳米铁镍双金属对废水处理,结果表明,负载型纳米铁镍双金属在实际废水中对直接耐晒黑G的去除率达到了99.98%。     

Characterization of compost biofiltration media.

The effect of compost quality on performance of biofiltration media was investigated. Three types of compost media were characterized in terms of their key properties, including pH, total organic carbon (TOC) and nitrogen, moisture content, oxygen uptake rates and heterotrophic and fungal plate counts. Laboratory-scale biofilter columns were each filled with a different compost medium mixed with buffer and a bulking agent. The columns were operated with a volatile organic compound (VOC) mixture consisting of ethyl alcohol, butyraldehyde, ethyl acetate, and 1,1-diethoxybutane and subjected to various operating conditions. After 13 months, the columns were sampled and post-characterization of the media was performed. A mixture of biosolids/horse manure compost, which had a high initial microbial activity, had the shortest acclimation period. Best overall performance, however, was observed with yard waste compost, which was the most stable medium. Media hydrophobicity was a key factor in long-term performance. Significant changes in compost structure, moisture content, pH, volatile solids, oxygen uptake rates, and microbial population densities were observed over the course of the study. Analyses of organic nitrogen content showed that significant amounts of nitrogen were not depleted from the media.     

曝气量对悬浮系统单级自养脱氮性能的影响

通过连续实验和间歇实验研究了不同曝气量对SBR系统自养脱氮性能的影响。连续实验表明,在进水氨氮浓度为155～185 mg/L时,曝气量分别为20、28、36和44 L/h时,TN去除率分别为80%、82%、80%和77%;增大和减小曝气量均会降低系统的脱氮效率。间歇实验表明,随着曝气量的增加,氨氮的降解速率有所升高,20、28、36和44 L/h曝气条件下氨氮的降解速率分别为7.23、7.25、7.86和7.95 mg/(g MLVSS.h);在降解的过程中DO浓度一直维持在较低的水平(<0.5 mg/L),pH值则呈先升高后降低的趋势;氨氮降解结束时,pH值和DO浓度同时升高。结果表明,改变曝气量会影响单级自养脱氮反应的进程,但对降解过程DO浓度值变化不大;DO浓度和pH值变化对氨降解结束具有指示作用。     

Backfitting Electrostatic Precipitators: Gas Velocity and Reliability Considerations

Abstract

The kinetic behavior of the toluene biofiltration process was investigated in this research. Toluene was used as a model compound for less water-soluble gas pollutants. The limiting factor in the overall toluene biofiltration process was determined by analyzing the effectiveness factor of the biofilm along the biofilter. Experiments were conducted in three laboratory-scale biofilters packed with mixtures of chaff/compost, D.E. (diatomaceous earth)/compost and GAC (granular activated carbon)/compost, respectively. A mathematical model previously proposed was verified in this study as being applicable to these biofilters packed with different filter materials. Both the experimental and theoretical results confirmed that the biodegradation rate along the biofilter followed the zero order, fractional order to first order kinetics as toluene concentration decreased. Moreover, at higher toluene concentration, biodegradation rate and mass flux of toluene were lower near the bottom of the biofilter due to substrate inhibition. Analysis of the effectiveness factor indicated that biofiltration of a less soluble compound such as toluene should not be operated at high gas flow rates (low gas residence times) due to the mass transfer limitation of such a system. At an approximate constant inlet toluene concentration of 0.9 g/m³, the toluene removal efficiency in these three biofilters would drop below 90% when the gas residence time decreased to 2.5, 2.5, and 2.0 min, respectively.     

Removal of propylene and butylene as individual compounds with compost and wood chip biofilters

Propylene and butylene are highly reactive volatile organic compounds (HRVOCs) in terms of ground-level ozone formation. This study examined the effectiveness of biofiltration in removing propylene and butylene as separate compounds. Specific objectives were (1) to measure maximum removal efficiencies for propylene and butylene and the corresponding microbial acclimation times, which will be useful in the design of future biofilters for removal of these compounds; (2) to compare removal efficiencies of propylene and butylene for different ratios of compost/hard wood-chip media; and (3) to identify the microorganisms responsible for propylene and butylene degradation. Two laboratory-scale polyvinyl chloride biofilter columns were filled with 28 in. of biofilter media (compost/wood-chip mixtures of 80:20 and 50:50 ratios). Close to 100% removal efficiency was obtained for propylene for inlet concentrations ranging from 2.9 x 10(4) to 6.3 x 10(4) parts per million (ppm) (232-602 g/m3-hr) and for butylene for inlet concentrations ranging from 91 to 643 ppm (1.7-13.6 g/m3-hr). The microbial acclimation period to attain 100% removal efficiency was 12-13 weeks for both compounds. The lack of similar microbial species in the fresh and used media likely accounts for the long acclimation time required. Both ratios of compost/wood chips (80:20 and 50:50) gave similar results. During the testing, media pH increased slightly from 7.1 to 7.5-7.7. None of the species in the used media that treated butylene were the same as those in the used media that treated propylene, indicating that different microbes are adept at degrading the two compounds.     

稻秆负荷与pH对稻秆厌氧发酵产酸系统启动过程的影响

为探讨稻秆负荷（即稻秆VS/污泥VSS）与发酵pH对稻秆厌氧发酵产酸系统启动过程产挥发性脂肪酸（VFAs）效果的影响,利用厌氧搅拌罐反应系统考察在不同的稻秆负荷（0.556、0.945、1.334和1.724 g/g）和不同的发酵pH（8.0、9.0和10.0）启动运行条件下的产酸性能,并分析了系统启动过程产酸与稻秆主要成分降解之间的关系。实验结果表明,VFAs浓度随稻秆负荷提高而增大,随发酵pH的升高而降低;发酵18 d时,发酵pH为9.0时,稻秆负荷1.334 g/g的产酸效果最好,VFAs浓度与稻秆产酸量分别为4 385.10 mg/L和2.19 gVFAs/g稻秆,此时半纤维素、纤维素和酸性洗涤木质素降解率分别为32.69%、22.53%和6.40%;稻秆负荷为0.945 g/g条件下,VFAs浓度在pH为8.0时达到最高值4 409.51 mg/L,此时稻秆降解量也最多,半纤维素、纤维素和酸性洗涤木质素降解率分别为28.60%、47.32%和22.69%。研究表明,稻秆负荷与发酵pH通过影响稻秆半纤维素、纤维素和木质素的降解影响稻秆厌氧发酵产酸的进程和效果。     

Degradation of silicone polymer in a field soil under natural conditions

Silicone polymers (PDMS = polydimethylsiloxane) are used in numerous consumer and industrial products. Our previous work showed that they will degrade in soil under laboratory conditions. This paper investigates PDMS degradation in the field. Four soil plots (each 2.44 m x 2.44 m) in Michigan were sprayed in May, 1997, with aqueous emulsion to achieve nominal soil PDMS concentrations of 0 (control), 215 (low), 430 (medium), and 860 (high) microg/g. Over the following summer, soil cores (0-5 and 5-10 cm) were collected every two weeks and analyzed for decrease in-total soil PDMS, and decrease in molecular weight of remaining PDMS. PDMS concentrations decreased 50% in 4.5, 5.3, and 9.6 weeks for the low, medium, and high treatments, respectively. Degradation rates were 0.26 (low), 0.44 (medium), and 0.44 (high) g PDMS/m2 day, indicating that degradation capacity of the soil was exceeded by the High treatment. Dimethylsilanediol (DMSD), the main degradation product, was detected in most samples at <5% of original PDMS. This is consistent with laboratory data showing biodegradation and volatilization of DMSD. Deeper sampling (to 20 cm) found only trace amounts of DMSD, and minor downward movement of the polymer. Respraying and subsequent analysis of one plot with a medium treatment in late August showed slow PDMS degradation during the cool, wet fall, followed by a 40% decrease over winter and extensive degradation during the summer of 1998. The study thus shows that PDMS will degrade under field conditions as predicted from laboratory experiments.     

Oxidation of gas mixtures containing dimethyl sulfide, hydrogen sulfide, and methanethiol using a two-stage biotrickling filter

A biofiltration technique was developed for removing a mixture of hydrogen sulfide (H2S), methanethiol (MeSH), and dimethyl sulfide (Me2S) from waste gases. Since H2S, especially at high concentrations, disturbs the removal of Me2S, two biotrickling filters with different microbes and operating pH levels were connected in series to create a two-stage system. Different loads of these gases were studied in order to determine their impact on the removal capacity of the system. The microbial consortia for these filters were enriched from the sludge of a Finnish refinery with bubbling H2S or Me2S. Acclimation for Me2S took 2 weeks, though no acclimation time was needed for the other gases. The first filter, at a pH of 2, removed most of the H2S and some of the MeSH and Me2S. The second filter, at a pH of approximately 6.5, removed the rest of the MeSH and most of the Me2S. The total maximum loads of the whole two-stage biotrickling filter were 1150 g/m3/day for H2S-S (suffix S indicates the results are counted as sulfur amounts), 879 g/m3/day for Me2S-S, and 66 g/m3/day for MeSH-S treated in a gas mixture. The average removal efficiencies for all gases tested were 99% or higher.     

Multiple microbial activities for volatile organic compounds reduction by biofiltration

In the northeast of Italy, high volatile organic carbon (VOC) emissions originate from small-medium companies producing furniture. In these conditions it is difficult to propose a single, efficient, and economic system to reduce pollution. Among the various choices, the biofiltration method could be a good solution, because microbial populations possess multiple VOC degradation potentials used to oxidize these compounds to CO2. Starting from the air emissions of a typical industrial wood-painting plant, a series of experiments studied in vitro microbial degradation of each individual VOC. Isolated strains were then added to a laboratory-scale biofiltration apparatus filled with an organic matrix, and the different VOC behavior demonstrated the potential of single and/or synergic microbial removal actions. When a single substrate was fed, the removal efficiency of a Pseudomonas aeruginosa inoculated reactor was 1.1, 1.17, and 0.33 g m(-3) hr(-1), respectively, for xylene, toluene, and ethoxy propyl acetate. A VOC mixture composed of butyl acetate, ethyl acetate, diacetin alcohol, ethoxy propanol acetate, methyl ethyl ketone, methyl isobutyl ketone, toluene, and xylene was then fed into a 2-m(3) reactor treating 100 m3 hr(-1) of contaminated air. The reactor was filled with the same mixture of organic matrix, enriched with all of the isolated strains together. During reactor study, different VOC loading rates were used, and the behavior was evaluated continuously. After a short acclimation period, the removal efficiency was > 65% at VOC load of 150-200 g m(-3) hr(-1). Quantification of removal efficiencies and VOC speciation confirmed the relationship among removal efficiencies, compound biodegradability, and the dynamic transport of each mixture component within the organic matrix. Samples of the fixed bed were withdrawn at different intervals and the heterogeneous microbial community evaluated for both total and differential compound counts.     

堆肥生物过滤器净化苯、甲苯混合废气的实验研究

选取木块和多孔塑料为填料,选择苯为VOCs代表,研究堆肥生物过滤器对高低浓度的苯生物降解性能。实验结果表明,（1) 以木块和多孔塑料为填料的堆肥生物过滤器对高、低浓度苯净化效率呈现降低后升高,最后再降低的过程,对高低浓度甲苯均呈现缓慢升高后降低的过程,高浓度苯的最大净化效率为90.5%和97.7%,甲苯的最大净化效率为71.34%和66.45%;（2) 以多孔塑料为填料的堆肥生物过滤器对高浓度苯具有较好的抗冲击性和抗负荷性,以木块为填料的堆肥生物过滤器对高浓度甲苯有更好的净化效果;（3) 堆肥生物过滤器对高低浓度苯、甲苯的平均净化率为68%和56%以上,低浓度苯和甲苯的平均去除能力分别为0.122和0.012 g/（m³·h）,最大去除能力为0.148和0.015 g/（m³·h）,而高浓度苯和甲苯的平均去除能力为0.94和0.11 g/（m³·h）,最大去除能力为1.32和0.135 g/（m³·h）。     

Transformation of microflora during degradation of gaseous toluene in a biofilter detected using PCR-DGGE

A laboratory-scale biofiltration system, the rotatory-switching biofilter (RSB), was operated for 199 days using toluene as a model pollutant. The target gaseous pollutant for the biofiltration experiment was approximately 300 ppmv of toluene. Toluene removal efficiency (RE, %) was initially approximately 20% with a 247-ppmv concentration (0.9 g m(-3)) of toluene during the first 10 days. Although the RE decreased several times whenever nitrogen was consumed, it again reached almost 100% when the nitrogen source was in sufficient supply. Denaturing gradient gel electrophoresis (DGGE) analysis was employed to assess the transformation ofmicroflora during operation of the biofilter The results based on a 16S rRNA gene profile showed that the microbial community structure changed with operation time. Although the microflora changed during the initial period (before day 40), transformation of the bacterial component was hardly observed after day 51. Statistical analyses of the DGGE profiles indicated that the bacterial community was almost unaffected by the environmental factors, such as adding ozone, high-level nitrogen supply, increase of loading toluene, and the shutdown of the RSB. The DGGE profile using tmoA-like genes, which encode proteins belonging to the hydroxylase component mono-oxygenases involved in the initial attack of aerobic benzene, toluene, ethylbenzene, and xylene degradation, confirmed the existence of toluene-degrading bacteria. There were at least four kinds of toluene-degradable bacteria having tmoA-like genes up to day 36, which decreased to two species after day 40. Sequence analysis after DGGE profiling revealed that Burkholderia cepacia, Sphingobacterium multivorum, and Pseudomonas putida were present in the biofilter. Only Alicycliphilus denitrificans was present throughout the whole operation period. In the initial stage of operating the RSB, many types of bacteria may have tried to adapt to the conditions, and subsequently, only selected bacteria were able to grow and to degrade toluene.     

Biofiltration of Trichloroethylene-Contaminated Air: A Pilot Study

Abstract

This project demonstrated the biofiltration of a trichloroethylene (TCE)-contaminated airstream generated by air stripping groundwater obtained from several wells located at the Anniston Army Depot, Anniston, AL. The effects of several critical process variables were investigated to evaluate technical and economic feasibility, define operating limits and preferred operating conditions, and develop design information for a full-scale biofilter system. Long-term operation of the demonstration biofilter system was conducted to evaluate the performance and reliability of the system under variable weather conditions. Propane was used as the primary substrate necessary to induce the production of a nonspecific oxygenase. Results indicated that the process scheme used to introduce propane into the biofiltration system had a significant impact on the observed TCE removal efficiency. TCE degradation rates were dependent on the inlet contaminant concentration as well as on the loading rate. No microbial inhibition was observed at inlet TCE concentrations as high as 87 parts per million on a volume basis.     

Performance of an innovative two-stage process converting food waste to hydrogen and methane

This study was conducted to evaluate the performance of an innovative two-stage process, BIOCELL, that was developed to produce hydrogen (H2) and methane (CH4) from food waste on the basis of phase separation, reactor rotation mode, and sequential batch technique. The BIOCELL process consisted of four leaching-bed reactors for H2 recovery and post-treatment and a UASB reactor for CH4 recovery. The leaching-bed reactors were operated in a rotation mode with a 2-day interval between degradation stages. The sequential batch technique was useful to optimize environmental conditions during H2 fermentation. The BIOCELL process demonstrated that, at the high volatile solids (VS) loading rate of 11.9 kg/m3 x day, it could remove 72.5% of VS and convert VS(removed) to H2 (28.2%) and CH4 (69.9%) on a chemical oxygen demand (COD) basis in 8 days. H2 gas production rate was 3.63 m3/m3 x day, while CH4 gas production rate was 1.75 m3/m3 x day. The yield values of H2 and CH4 were 0.31 and 0.21 m3/kg VS(added), respectively. Moreover, the output from the post-treatment could be used as a soil amendment. The BIOCELL process proved to be stable, reliable, and effective in resource recovery as well as waste stabilization.     

Anaerobic biodegradation of methyl tert-butyl ether under iron-reducing conditions in batch and continuous-flow cultures.

The feasibility of biodegradation of the fuel oxygenate methyl tert-butyl ether (MTBE) under iron-reducing conditions was explored in batch and continuous-flow systems. A porous pot completely-mixed reactor was seeded with diverse cultures and operated under iron-reducing conditions. For batch studies, culture from the reactor was transferred anaerobically to serum bottles containing either MTBE alone or MTBE with ethanol (EtOH) and excess electron acceptor. In the continuous-flow reactor, MTBE conversion to tert-butyl alcohol (TBA) was observed after 181 days of operation, and stable removal was achieved throughout the remainder of the study. Simultaneously, both the MTBE only and the MTBE and EtOH iron-reducing batch serum bottles also began to degrade MTBE. Bottles were respiked and the degradation rate was determined to be 2.36 +/- 0.10 x 10(-4) mmol MTBE/min-kgVSS. The EtOH present with MTBE degraded faster (7.76 +/- 0.08 x 10(-3) mmol EtOH/min-kg VSS) but did not have a noticeable effect on the rate of MTBE degradation. No evidence of TBA degradation was observed by the iron-reducing cultures. Stoichiometry of iron utilization was determined from the iron balance of the continuous-flow reactor, and it was found that the bulk of the electron acceptor was required for energy and maintenance with little remaining for cell synthesis. This is consistent with a yield coefficient of less than 0.1. Molecular analysis of the iron-reducing culture by denaturing gradient gel electrophoresis indicated that uncultured strains of delta-Proteobacteria were dominant in the reactor.     

Performance evaluation of sequencing batch reactor for beverage industrial wastewater treatment

Attempts were made in this study to examine the effectiveness of sequencing batch reactor (SBR) for the treatment of beverage industrial wastewater. The SBR was operated at three different organic loading rates (OLRs): 2, 1.7 and 1.1 kg COD/m3 d. Results of continuous long-term operation showed that by decreasing OLR from 2 to 1.7 kg COD/m3 day, the removal efficiency was increased from 95.5 to 99.3% for COD, from 95.3 to 98.1% for BOD and from 87 to 97.7% for TSS. While further decreasing of the OLR to 1.1 kg COD/m3 day, there is no significant adverse effect on organics removal. Also, residual total nitrogen (TN) concentration decreased by decreasing the OLR. However, increasing the OLRs exerted a slightly negative effect on the removal of total phosphorous. On the other hand, the experimental data indicated that the substrate utilization kinetic followed Monod's kinetics model approximately. The maximum specific substrate utilization rate (micro(max), half velocity coefficient (Ks), growth yield coefficient (Y) and decay coefficient (Kd) were 2.94 d(-1), 15.22 mg/L, 0.2384 g VSS/g COD and 0.2019 h(-1), respectively.     

Effects of lime amendment on availability of heavy metals and maturation in sewage sludge composting

A batch composting study was performed to evaluate the feasibility of co-composting sewage sludge with lime, aiming at reducing the availability of heavy metals in the sludge compost. Sewage sludge with sawdust as bulking agent was amended with lime at 0, 0.63, 1.0, and 1.63% w/w, and composted for 100 days in laboratory batch reactors. The changes in temperature, pH, electrical conductivity (EC), and extractable heavy metal contents were measured while compost maturity was determined by C/N(organic) and cress seed germination during the composting period. Liming raised pH of compost effectively at the initial stage of composting and caused a decrease in EC through precipitation of soluble ions. Lime amendment also significantly reduced water-soluble and Diethylene triamine pentracetic acid (DTPA)-extractable metal contents. The maximum reductions were 60 and 40% for Cu, 80 and 40% for Mn, 55 and 10% for Zn, and 20 and 25% for Ni at the end of the composting period for the lime-amended sludge as compared to the control. In spite of the inhibitory effect of lime amendment on the decomposition activity of sewage sludge, all treatments reached maturation after 63 days of composting as indicated by the results of C/N(organic) ratio and cress seed germination test results. A lime amendment of < or =1.0% is recommended to co-compost with sewage sludge.     

Regeneration of a compost biofilter degrading high loads of ammonia by addition of gaseous methanol

The long-term stability of a biofilter loaded with waste gases containing NH3 concentrations larger than 100 ppmv was studied in a laboratory-scale compost reactor. At an empty bed residence time (tau) of 21 sec, elimination capacities of more than 300 g NH3/m3/day were obtained at elimination efficiencies up to 87%. Because of absorption and nitrification, almost 80% of the NH3-N eliminated from the waste gas could be recovered in the compost as NH4(+)-N or NO2-/NO3(-)-N. The high elimination capacities could be maintained as long as the NH4+/ NOX- concentration in the carrier material was less than 4 g NH4+/NOx(-)-N/kg wet compost. Above this critical value, osmotic effects inhibited the nitrifying activity, and the elimination capacity for NH3 decreased. To restore the biofilter performance, a carbon source (methanol) was added to reduce NH4+/NOx- accumulated in the compost. Results indicate that methylotrophic microorganisms did convert NH4+/NOx- into biomass, as long as the NO3- content in the compost was larger than 0.1 g NO3(-)-N/kg compost. Removal efficiencies of CH3OH of more than 90% were obtained at volumetric loads up to 11,000 g CH3OH/ m3/day. It is shown that addition of CH3OH is a suitable technique for regenerating the compost material from osmotic inhibition as a result of high NH3 loading. The biofilter was operated for 4 months with alternating load ing of NH3 and CH3OH.