Screening of compost for PAHs and pesticides using static subcritical water extraction.

Static subcritical water extraction (SubWE) along with solid phase extraction (SPE) was used for the analysis of PAHs and pesticides in municipal solid waste compost. Yields obtained for PAHs in certified reference sediment (CRM 104) were acceptable. The extraction method was simple, rapid, used small sample sizes, and no sample drying was required. Analysis of samples was performed by GC/MS and HPLC. Recovery of spiked pesticides was greatest at 110 degrees C for 20 min extraction time. The optimum extraction for PAH analysis was achieved at 150 degrees C for 20 min. Addition of C-18 resin as an "alternate sorbent" upon cooling increased recovery of PAHs but not of pesticides, however, it increased the stability of atrazine and propazine at higher temperatures. Analysis of three municipal compost samples from the Dayton, OH (USA) area showed no pesticides above the detection limit, however, PAH totals for 11 PAHs were 15.97, 14.42, and 20.79 microg g(-1). The totals of six of the seven carcinogenic PAHs, for which remediation goals in the United States is 4.6 microg g(-1), were determined to be 9.89, 6.77, and 13.06 microg g(-1) dry weight. The highest PAH totals were obtained from compost containing sewage sludge.     

Application of magnetite-activated persulfate oxidation for the degradation of PAHs in contaminated soils

In this study, feasibility of magnetite-activated persulfate oxidation (AP) was evaluated for the degradation of polycyclic aromatic hydrocarbons (PAHs) in batch slurry system. Persulfate oxidation activated with soluble Fe(II) (FP) or without activation (SP) was also tested. Kinetic oxidation of PAHs was tracked in spiked sand and in aged PAH contaminated soils at circumneutral pH. Quartz sand was spiked with: (i) single model pollutant (fluorenone) and (ii) organic extract isolated from two PAH contaminated soils (H and NM sampled from ancient coking plants) and was subjected to oxidation. Oxidation was also performed on real H and NM soils with and without an extraction pretreatment. Results indicate that oxidation of fluorenone resulted in its complete degradation by AP while abatement was very low (<20%) by SP or FP. In soil extracts spiked on sand, significant degradation of 16 PAHs was observed by AP (70-80%) in 1 week as compared to only 15% by SP or FP systems. But no PAH abatement was observed in real soils whatever the treatment used (AP, FP or SP). Then soils were subjected to an extraction pretreatment but without isolation of organic extract from soil. Oxidation of this pretreated soil showed significant abatement of PAHs by AP. On the other hand, very low degradation was achieved by FP or SP. Selective degradation of PAHs was observed by AP with lower degradation efficiency towards high molecular weight PAHs. Analyses revealed that no by-products were formed during oxidation. The results of this study demonstrate that magnetite can activate persulfate at circumneutral pH for an effective degradation of PAHs in soils. However, availability of PAHs and soil matrix were found to be the most critical factors for degradation efficiency.     

Contamination by polycyclic aromatic hydrocarbons in the Jiulong River Estuary and Western Xiamen Sea, China

The distribution of 16 polycyclic aromatic hydrocarbons (PAHs) was determined in water, sediment and pore water of the Jiulong River Estuary and Western Xiamen Sea, China. Total PAH concentrations varied from 6.96 to 26.9 microg/l in water, 59-1177 ng/ g dry weight in surficial sediments, and 158-949 microg/l in pore water. The PAHs were present in higher levels in pore water than in surface water, due possibly to higher concentrations of dissolved organic carbon or colloids with which the hydrophobic pollutants were strongly associated. Such a concentration gradient implies a potential flux of pollutants from sediment pore water to overlying water. The levels of PAHs in water and pore water were significantly higher than those found in 1998, suggesting recent inputs of these compounds into the area and re-working of sediment phase. The composition pattern of PAHs in the three phases was dominated by high molecular weight PAHs, in particular 5-ring PAHs. The salinity profile of dissolved PAHs suggested that they all behaved non-conservatively due to deviation from the theoretical dilution line. No correlation was found between PAH concentrations in sediment and those in pore water, and the correlation between the partition coefficients of PAHs and sediment organic carbon content was not significant, suggesting the complexity of the partition behaviour of PAHs. As a result of high PAH concentrations in water and pore water, it is likely that they may have caused mortality to certain exposed organisms.     

Contamination of rivers in Tianjin, China by polycyclic aromatic hydrocarbons

Tianjin urban/industrial complex is highly polluted by some persistent organic pollutants. In this study, the levels of 16 priority polycyclic aromatic hydrocarbons (PAHs) were tested in sediment, water, and suspended particulate matter (SPM) samples in 10 rivers in Tianjin. The total concentration of 16 PAHs varied from 0.787 to 1943 microg/g dry weight in sediment, from 45.81 to 1272 ng/L in water, and from 0.938 to 64.2 microg/g dry weight in SPM. The levels of PAHs in these media are high in comparison with values reported from other river and marine systems. Variability of total concentrations of PAHs in sediment, water, and SPM from nine different rivers is consistent with each other. No obvious trends of total PAHs concentration variations were found between upstream and downstream sediment, water, and SPM samples for most rivers, which indicate local inputs and disturbances along these rivers. The spatial distributions of three-phase PAHs are very similar to each other, and they are also similar to those found in topsoil. However, their chemical profiles are significantly different from that of topsoil. The change of profiles is consistent with the different aqueous transport capability of 16 PAHs. Low molecular weight PAHs predomination suggests a relatively recent local source and coal combustion source of PAHs in the study area.     

Analysis of polycyclic aromatic hydrocarbons in sediment reference materials by microwave-assisted extraction

The microwave-assisted extraction (MAE) of polycyclic aromatic hydrocarbons (PAHs) from harbor sediment reference material EC-1, marine sediment reference material HS-2 and PAH-spiked river bed soil was conducted. The extraction conditions for EC-1 were carried out at 70 degrees C and 100 degrees C under pressure in closed vessels with cyclohexane acetone (1:1), cyclohexane-water (3:1), hexane acetone (1:1), and hexane-water (3:1) for 10 min. A comparison between MAE and a 16-h Soxhlet extraction (SX) method showed that both techniques gave comparable results with certified values. MAE has advantages over the currently used Soxhlet technique due to a faster extraction time and lower quantity of solvent used. The consumption of organic solvent of the microwave method was less than one-tenth compared to Soxhlet.     

Slurry-phase ozonation for remediation of sediments contaminated by polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are a group of toxic, persistent, bioaccumulating organic compounds containing two or more fused aromatic rings. They are listed by the U.S. Environmental Protection Agency as priority pollutants because of their carcinogenicity and toxicity. Employing ozonation as a remediation technique, this work investigated the treatability of a sediment sample from a freshwater boat slip subjected to coal tar contamination over a long period. The contaminated sediment sample contained high levels of PAHs in the forms of naphthalene, phenanthrene, pyrene, and benzo[a]pyrene, among other byproducts present in the humic and solid phases of the sediment. The objectives of this work were to examine (1) the degradation of PAHs in the contaminated sediment as treated by ozonation in the slurry form, (2) the effects of ozonation upon the soil matrix and the biodegradability of the resultant PAH intermediates, and (3) the feasibility of a combined technique using O3 as a pretreatment followed by biological degradation. The sediment was made into 3% w/w soil slurries and ozonated in a 1.7-L semi-batch, well-stirred reactor equipped with pH control and a cold trap for the gaseous effluent. Samples were collected after different ozonation durations and tested for biochemical oxygen demand (BOD), chemical oxygen demand (COD), UV absorbance, and toxicity, along with quantitative and qualitative determinations of the parent and daughter intermediates using gas chromatography/flame ionization detection (GC/FID), GC/mass spectrometry (MS), and ion chromatography (IC) techniques. The GC/MS technique identified 16 compounds associated with the humic and solid phases of the sediment. Intermediates identified at different ozonation times suggested that the degradation of PAHs was initiated by an O3 attack resulting in ring cleavage, followed by the intermediates' oxidation reactions with O3 and the concomitant OH radical toward their mineralization. Results suggested that ozonation for 2 hr removed 50-100% of various PAHs in the solid and liquid phases (as well as the aqueous and gaseous media resulting from the treatment process) of the sediment sample and that organic and inorganic constituents of the sediment were also altered by ozonation. Measurements and comparisons of BOD, COD, UV absorbance, and toxicity of the samples further suggested that ozonation improved the bioavailability and biodegradability of the contaminants, despite the increased toxicity of the treatment effluent. An integrated chemical-biological system appeared to be feasible for treating recalcitrant compounds.     

Characterization of extractable and non-extractable polycyclic aromatic hydrocarbons in soils and sediments from the Pearl River Delta, China

Formation of bound residues of pollutants in soils and sediments is an important process to control the fate of pollutants in the environment. The most of bound residue is not solvent extractable. In this paper, we measured both extractable and non-extractable polycyclic aromatic hydrocarbons (PAHs) in different organic matter fractions of samples from the Pearl River Delta, China. Non-extractable PAHs concentration was 234.45-1424.57 μg/kg and accounted for 33.78-57.44% of total PAHs. 2-3 Ring PAHs were the dominant species and differed in concentration substantially between the samples. The atomic ratio of PAHs over organic-C in the fractions ordered as solvent soluble organic matter > humin > humic acids, matching the content of aliphatic moieties in the fractions of organic matter. The ratio of extractable and non-extractable PAHs may relate to the aging process of PAHs in soil and sediment.     

Occurrence of PAHs, PCBs and organochlorine pesticides in the Tonghui River of Beijing, China

Tonghui River, a typical river in Beijing, People's Republic of China, was studied for its water and sediment quality, by determining the levels of 16 polycyclic aromatic hydrocarbons (PAHs), 12 polychlorinated biphenyls (PCBs) and 18 organochlorine pesticides in water and sediment samples. Total PAHs, PCBs and organochlorine pesticides concentrations in water varied from 192.5 to 2651 ng/l, 31.58-344.9 ng/l and 134.9-3788 ng/l, respectively. The total PAHs, PCBs and organochlorine pesticides concentrations in surficial sediments were 127-928 ng/g, 0.78-8.47 ng/g and 1.79-13.98 ng/g dry weight, respectively. The results showed that the concentration of these selected organic pollutants in sediment was higher than those in surface water. It may be due to the fact that organic hydrophobic pollutants tend to stay in the sediments. The PAHs were dominated by 2-, 3-ring components in water samples and by 3- and 4-ring compounds in sediment. For organochlorines, alpha-HCH, delta-HCH, Heptachlor, Endosulfan II, DDT are the major organochlorine pesticides in water while Heptachlor, Dieldrin and DDE composed of 95% of total organochlorine pesticides in sediment. For HCHs (HCHs=alpha-HCH+beta-HCH+gamma-HCH+delta-HCH), the predominance of alpha-HCH of total HCHs were clearly observed in water and sediment. PCB18, PCB31 and PCB52 were predominant in water, on average these compounds collectively accounted for 67% of total PCBs. But in sediment, the predominant compounds were PCB28, PCB31 and PCB153, which accounted for 71% of total PCBs in sediment. The levels of micro pollutants in our study areas were compared with other studies.     

Ectomycorrhizas impede phytoremediation of polycyclic aromatic hydrocarbons (PAHs) both within and beyond the rhizosphere

Exploitation of mycorrhizas to enhance phytoremediation of organic pollutants has received attention recently due to their positive effects on establishment of plants in polluted soils. Some evidence exist that ectomycorrhizas enhance the degradation of pollutants of low recalcitrance, while less easily degradable polyaromatic molecules have been degraded only by some of these fungi in vitro. Natural polyaromatic (humic) substances are degraded more slowly in soil where ectomycorrhizal fungi are present, thus phytoremediation of recalcitrant pollutants may not benefit from the presence of these fungi. Using a soil spiked with three polycyclic aromatic hydrocarbons (PAHs) and an industrially polluted soil (1 g kg(-1) of summation operator12 PAHs), we show that the ectomycorrhizal fungus Suillus bovinus, forming hydrophobic mycelium in soil that would easily enter into contact with hydrophobic pollutants, impedes rather than promotes PAH degradation. This result is likely to be a nutrient depletion effect caused by fungal scavenging of mineral nutrients.     

我国环境介质中多环芳烃的分布及其生态风险

持久性有机污染物多环芳烃(PAHs)在我国环境介质中广泛分布,美国EPA规定的16种.优先控制多环芳烃大多在我国大气、水体、沉积物、土壤和生物体内检出.总结了我国环境介质中PAHs污染水平及特点,分析了其存在的环境风险.我国大气中PAHs污染较重,尤其是北方.水体已普遍受PAHs污染,其中部分水体污染严重;沉积物多环芳烃污染大多处于低生态风险水平,但沉积记录研究表明有越来越严重的趋势.我国土壤和生物体PAHs含量较低,污染生态风险较小.部分区域蔬菜中PAHs含量较高,存在不可忽视的生态风险.     

Study of factors affecting on the extraction efficiency of polycyclic aromatic hydrocarbons from soils using open-vessel focused microwave-assisted extraction

As part of an evaluation of focused microwave-assisted extraction (FMAE) using an open-vessel system, the effects of matrix, moisture content, ageing, and solvent have been studied on the extraction efficiency of polycyclic aromatic hydrocarbons (PAHs) from spiked soils. PAHs were spiked onto three different uncontaminated air dried and originally wet soil matrices with 1- and 20-day ageing periods. Solvents used were hexane–acetone (1:1), cyclohexane–acetone (1:1) and dichloromethane. FMAE only required a small amount of solvent (20 ml) and short extraction time (10 min) in the open cell under 90 W of microwave power. The results revealed that the extraction efficiency strongly depends on the nature of soil matrix; moisture content may enhance the recoveries of PAHs for many cases; and, the influence of the type of solvent is not significant. A comparison between microwave extraction and 16-h Soxhlet extraction has been made on spiked soils. It evidenced that the microwave method under ambient pressure is a suitable alternative to Soxhlet method for the analysis of PAHs in soils. For the evaluation of the developed FMAE method, three reference materials were used. The PAHs recovered from three reference materials were in a good agreement with reference values.     

Tidal salt marsh sediment in California, USA. Part 1: occurrence and sources of organic contaminants

Surface sediment samples (0-5 cm) from five tidal marshes along the coast of California, USA were analyzed for organic pollutants to investigate their relationship to land use, current distribution within marshes, and possible sources. Among the study areas, Stege Marsh, located in San Francisco Bay, was the most contaminated. Compared to San Francisco Bay, Stege Marsh had much higher levels of organic contaminants such as PCBs (polychlorinated biphenyls), DDTs, and chlordanes. At reference marshes (Tom's Point and Walker Creek in Tomales Bay), organic contaminants in sediments were very low. While PAHs (polycyclic aromatic hydrocarbons) were found at all of the study areas (22-13,600 ng g(-1)), measurable concentrations of PCBs were found only in the sediments from Stege Marsh (80-9,940 ng g(-1)). Combustion related (pyrogenic) high molecular weight PAHs were dominant in sediments from Stege and Carpinteria Marshes, while in sediments from Tom's Point and Walker Creek petroleum related (petrogenic) low molecular weight PAHs and alkyl-substituted PAHs were much more abundant than pyrogenic PAHs. PCB congener patterns in all of the Stege Marsh samples were the same and revealed that Aroclor 1248 was a predominant source. In all marshes, the sum of DDE and DDD accounted for more than 90% of total DDTs, indicating that DDT has degraded significantly. The ratios of p,p'-DDE to p,p'-DDD in sediments from Stege Marsh provide evidence of possible previous use of technical DDD. Chlordane ratios indicated that chlordanes have degraded slightly. Bis(2-ethylhexyl)phthalate (280-32,000 ng g(-1)) was the most abundant phthalate. The data indicates that Stege Marsh may be a source of contaminants that continue to be discharged into San Francisco Bay.     

Development of a reference artificial sediment for chemical testing adapted to the MELA sediment contact assay

Most persistent organic pollutants, due to their hydrophobic properties, accumulate in aquatic sediments and represent a high risk for sediment quality. To assess the toxicity of hydrophobic pollutants, a novel approach was recently proposed as an alternative to replace, refine and reduce animal experimentation: the medaka embryo–larval sediment contact assay (MELAc). This assay is performed with Japanese medaka embryos incubated on a natural sediment spiked with the compound being tested. With the aim of improving this assay, our study developed a reference exposure protocol with an artificial sediment specifically designed to limit natural sediment composition uncertainties and preparation variability. The optimum composition of the new artificial sediment was tested using a model polycyclic aromatic hydrocarbon (PAH), fluoranthene. The sediment was then validated with two other model PAHs, benz[a]anthracene and benzo[a]pyrene. Various developmental end points were recorded, including survival, embryonic heartbeat, hatching delay, hatching success, larval biometry and abnormalities. The final artificial sediment composition was set at 2.5 % dry weight (dw) Sphagnum peat, 5 % dw kaolin clay and 92.5 % dw silica of 0.2- to 0.5-mm grain size. In contrast with natural sediments, the chemical components of this artificial matrix are fully defined and readily identifiable. It is totally safe for fish embryos and presents relatively high sorption capacities for hydrophobic compounds. Studies with other hydrophobic and metallic contaminants and mixtures should be performed to further validate this artificial sediment.     

Treatment system for solid matrix contaminated with fluoranthene. I--Modified extraction technique.

A laboratory-scale ultrasonication technique was developed for fluoranthene extraction from soils and sediments where the utilized organic solvent would be recovered after the extraction process. Therefore, the remedied soils and sediments would be free from toxicant and trace of added chemicals. The developed ultrasonication technique outlined here is an integrated part of a complete remediation system consisting of extraction and solar detoxification reactors. This paper investigates extraction efficiencies under different conditions, outlines solvent recovery technique and compares extraction efficiency of the developed ultrasonication technique with a commercially available laboratory-scale sonication bath. The spiked soil sample with fluoranthene (19.4 microg g(-1)) and organic solvent was ultrasonicated at 40 degrees C for 20 min. The sonicated mixture was allowed to settle for 10 min before the extract gravitated into the modified solar reactor for fluoranthene detoxification. The added solvents were removed from the remedied soil before it was released to site. The mixture of cyclohexane and ethanol (CH:ETOH) (3:1) was the favorable solvent from among 10 organic solvents because of its high extraction efficiency, safety and low cost. Preliminary results indicated that the developed extraction technique recovered more than 93% of fluoranthene from soil samples.     

Sequential UV-biological degradation of polycyclic aromatic hydrocarbons in two-phases partitioning bioreactors

A method based on UV-irradiation in organic solvent followed by transfer of the remaining pollutants into silicone oil for subsequent biodegradation in a biphasic system inoculated with a phenanthrene degrading Pseudomonas sp. was tested for the treatment of various mixtures of PAHs. Acetone was first selected as the most suitable solvent compared to methanol, acetonitrile and silicone oil for the removal of pyrene and phenanthrene. The sequential treatment was then applied to the treatment of a mixture of fluorene, phenanthrene, anthracene, fluoranthrene, pyrene, benzo(a)anthracene and benzo(a)pyrene in acetone. These compounds were photodegraded in the following order of initial removal rates (mg l(-1) d(-1)): benzo(a)pyrene (7.8) > anthracene (5.0) > benzo(a)anthracene (2.5) > fluoranthrene (1.8) > pyrene (1.5) > phenanthrene (1.2) > fluorene (0.2). UV-treatment allowed complete removal of, anthracene, benzo(a)anthracene and benzo(a)pyrene and removals of 63% of pyrene and 37% of fluorene after 434 h or irradiation. The subsequent biological treatment removed the remaining phenanthrene and fluorene by 100% and 90%, respectively, after 790 h of cultivation. Although less efficient due to the presence of interfering compounds, the UV-biological treatment of a soil extract allowed a 63% removal of the seven PAHs named above. Microbial growth did not occur when the pollutants were directly supplied to the microorganism showing that biphasic systems reduced the toxicity effects cause by mixtures of PAHs at high concentrations. This study demonstrates the potential of selective UV treatment of high molecular weight PAHs followed by biological treatment of the low molecular weight species in biphasic systems.     

Release of polycyclic aromatic hydrocarbons from Yangtze River sediment cores during periods of simulated resuspension

The role of resuspension duration on release of 16 PAHs was measured experimentally using a particle entrainment simulator (PES). Three sediment cores were resuspended for 12h at 0.2 and 0.5N m(-2). PAHs in water column and total suspended solids (TSS) were monitored at intervals. After 0.25h of resuspension, PAH release was on average 42% of their concentrations after 12h of resuspension, indicating fast release of PAHs from sediments in an initial short time. Moreover, PAHs released faster at 0.5N m(-2) than at 0.2N m(-2); low molecular weight PAHs (2-3-ring) released faster than median molecular weight (4-ring) PAHs. PAH concentrations in TSS showed generally increase with time and differences in magnitudes based on sediment type and energy. Overall, the composition of sediments is the major factor in determining the amount of released PAHs, more so than the level of resuspension energy applied.     

Uptake of selected PAHs from contaminated soils by rice seedlings (Oryza sativa) and influence of rhizosphere on PAH distribution

The uptake of selected polycyclic aromatic hydrocarbons (PAHs) by rice (Oryza sativa) seedlings from spiked aged soils was investigated. When applied to soils aged for 4 months, naphthalene, phenanthrene, and pyrene exhibited volatilization loss of 98, 95, and 30%, respectively, with the remaining fraction being fixed by soil organic matter and/or degraded by soil microbes. In general, concentrations of the three PAHs in rice roots were greater than those in the shoots. The concentrations of root associated PHN and PYR increased proportionally with both soil solution and rhizosphere concentrations. PAH concentrations in shoots were largely independent of those in soil solution, rice roots, or rhizosphere soil. The relative contributions of plant uptake and plant-promoted rhizosphere microbial biodegradation to the total mass balance were 0.24 and 14%, respectively, based on PYR concentrations in rhizosphere and non-rhizosphere soils, the biomass of rice roots, and the dry soil weight.     

Polycyclic aromatic hydrocarbons in the surface sediments from Yellow River, China

Fourteen surface sediment samples were collected from Lanzhou Reach of Yellow River, China in July 2005. The concentrations of 16 priority polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatography equipped with a mass spectrometry detector (GC-MS). Total concentrations of the PAHs ranged from 464 to 2621 ng/g dry weight. Sediment samples with the highest PAH concentrations appeared at the downstream of Lanzhou City, where there was the biggest wastewater discharge pipeline from Lanzhou Oil Refinery Factory and Lanzhou Chemical Industry Company. Municipal sewage also contributed to the PAH contamination in the sediments. A correlation existed between the sediment organic carbon content (f(oc)) and the total PAH concentrations (r(2)=0.57), suggesting that sediment organic carbon content played an important role in controlling the PAHs levels in the sediments. According to the observed molecular indices, PAHs contamination in Lanzhou Reach of Yellow River originated both from the high-temperature pyrolytic processes and from the petrogenic source, showing a mixed PAH input pattern, which was also confirmed by the results of a principal component analysis (PCA). According to the numerical effect-based sediment quality guidelines (SQGs) of the United States, the levels of PAHs at most studied sites in Lanzhou Reach of Yellow River should not exert adverse biological effects. Although at some sites (such as S10, S12, etc.) one PAH may exceed the effects range low (ERL), individual PAH did not exceed the effects range median (ERM). The results indicated that sediments in all sites should have potential biological impact, but should have no impairment.     

Effects of soil organic matter on the development of the microbial polycyclic aromatic hydrocarbons (PAHs) degradation potentials

The microbial activity in soils was a critical factor governing the degradation of organic micro-pollutants. The present study was conducted to analyze the effects of soil organic matter on the development of degradation potentials for polycyclic aromatic hydrocarbons (PAHs). Most of the degradation kinetics for PAHs by the indigenous microorganisms developed in soils can be fitted with the Logistic growth models. The microbial activities were relatively lower in the soils with the lowest and highest organic matter content, which were likely due to the nutrition limit and PAH sequestration. The microbial activities developed in humic acid (HA) were much higher than those developed in humin, which was demonstrated to be able to sequester organic pollutants stronger. The results suggested that the nutrition support and sequestration were the two major mechanisms, that soil organic matter influenced the development of microbial PAHs degradation potentials.     

Formation of bound residues by naphthalene and cis-naphthalene-1,2-dihydrodiol

The formation of bound residues by naphthalene and its metabolite, cis-naphthalene-1,2-dihydrodiol, in a sediment (1% OC), a silty loam soil (2.9% OC) and a peat (26% OC) was examined. The experiments were carried out under both sterile and nonsterile conditions for up to 35 days. The samples containing bound contaminant were hydrolyzed at an alkaline pH and fractionated using 3,000 and 500 Da molecular weight cutoff ultrafiltration membranes in series. The results for all the geosorbents examined showed that bound residue formation is low for naphthalene and between 5 and 20 times higher for the metabolite. The amount of bound residues released by hydrolysis was higher for the metabolite than for the parent compound for all the samples. The molecular weight distribution of bound radioactivity after hydrolysis showed binding to the high molecular weight components of the sediment organic matter and to the low molecular weight components for soil and peat organic matter when incubated with cis-naphthalene-1,2-dihydrodiol. Experiments performed with naphthalene-UL-(14)C showed larger amounts of bound residue found than in experiments with naphthalene-1-(14)C.