Effects of NO2 and SO2 on selective catalytic reduction of nitrogen oxides by ammonia

The selective catalytic reduction (SCR) characteristics of NO and NO(2) over V(2)O(5)-WO(3)-MnO(2)/TiO(2) catalyst using ammonia as a reducing agent have been determined in a fixed-bed reactor at 200-400 degrees C. The presence of NO(2) enhances the SCR activity at lower temperatures and the optimum ratio of NO(2)/NO(x) is found to be 0.5. During the SCR reactions, there are some side reactions occurred such as ammonia oxidation and N(2)O formation. At higher temperatures, the selective catalytic oxidation of ammonia and the nitrous oxide formation compete with the SCR reactions. The denitrification (DeNO(x)) conversion decreases at lower temperatures but it increases at higher temperatures with increasing SO(2) concentration. The presence of SO(2) in the feeds inhibits N(2)O formation.     

CuCoOx／TiO2催化氧化NO性能研究

采用浸渍法制备了CuCoOx／TiO2催化剂,考察了焙烧温度、反应温度、氧含量、NO浓度和空间速度对催化剂催化氧化NO性能的影响,并考察了催化剂的抗硫抗水性能。XRD、TPR和BET分析表明,350℃焙烧的催化剂具有CuCo2O4尖晶石结构,比表面积大,对NO的氧化效果好。在空速为5000h^-1,NO进口浓度500mg／m^3,含氧量10％的条件下,反应温度300℃时NO转化率可达79．5％,250℃时NO转化率接近50％。该催化剂具有良好的单独抗SO2、抗H2O毒化性能,H2O和SO2同时存在时很快失活。该催化剂可用于不同时含H2O和SO2的含NO气体催化氧化后再吸收处理。     

Effects of sulfur dioxide and nitric oxide on mercury oxidation and reduction under homogeneous conditions

This paper is particularly related to elemental mercury (Hg0) oxidation and divalent mercury (Hg2+) reduction under simulated flue gas conditions in the presence of nitric oxide (NO) and sulfur dioxide (SO2). As a powerful oxidant and chlorinating reagent, Cl2 has the potential for Hg oxidation. However, the detailed mechanism for the interactions, especially among chlorine (Cl)-containing species, SO2, NO, as well as H2O, remains ambiguous. Research described in this paper therefore focused on the impacts of SO2 and NO on Hg0 oxidation and Hg2+ reduction with the intent of unraveling unrecognized interactions among Cl species, SO2, and NO most importantly in the presence of H2O. The experimental results demonstrated that SO2 and NO had pronounced inhibitory effects on Hg0 oxidation at high temperatures when H2O was also present in the gas blend. Such a demonstration was further confirmed by the reduction of Hg2+ back into its elemental form. Data revealed that SO2 and NO were capable of promoting homogeneous reduction of Hg2+ to Hg0 with H2O being present. However, the above inhibition or promotion disappeared under homogeneous conditions when H2O was removed from the gas blend.     

The effects of manganese precursors on Mn-based/TiO2 catalysts for catalytic reduction of NO with NH3

Manganese acetate (MnAc) and manganese nitrate (MnN) were employed as precursors for the preparation of MnAc)/TiO2, Mn (N)/TiO2, Mn(Ac)-Ce/TiO2, and Mn(N)-Ce/TiO2 by impregnation. These complexes were used as catalysts in the low-temperature selective catalytic reduction of NO with NH3. The influence of manganese precursors on catalyst characteristics, the reduction activity, and the stability of the catalysts to poisoning by H2O and SO2 were studied. Experiments showed that Mn(N) produced MnO2 with large grain sizes in Mn(N)/TiO2 catalyst. On the contrary, Mn(Ac) led to highly dispersed and amorphous Mn2O3 in Mn (Ac)/TiO2 catalyst, which had better catalytic activity and stability to SO2 at low temperatures. The doping of cerium reduced the differences in catalytic performance between the catalysts derived from different Mn precursors.     

Photocatalytic hydrogen generation in the presence of chloroacetic acids over Pt/TiO2

In the presence of chloroacetic acids, the photocatalytic hydrogen evolution and decomposition of the pollutants over Pt/TiO2 have been investigated. The Pt/TiO2 was prepared by photodeposition. Monochloroacetic acid and dichloroacetic acid enhance photocatalytic hydrogen generation, whereas trichloroacetic acid does not. The photocatalytic oxidation of monochloroacetic acid and dichloroacetic acid mainly produces CO2, HCl and formaldehyde, whereas the photocatalytic oxidation of trichloroacetic acid mainly produces CO2 and HCl. The effect of the concentration of monochloroacetic acid and dichloroacetic acid on the hydrogen generation rate is consistent with a Langmuir-Hinshelwood kinetic model. A possible reaction mechanism was discussed.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

Superior pillared clay catalysts for selective catalytic reduction of nitrogen oxides for power plant emission control

Fe(3+)-, Cr(3+)-, Cu(2+)-, Mn(2+)-, Co(2+)-, and Ni(2+)-exchanged Al2O3-pillared interlayer clay (PILC) or TiO2-PILC catalysts are investigated for the selective catalytic reduction (SCR) of nitric oxide by ammonia in the presence of excess oxygen. Fe(3+)-exchanged pillared clay is found to be the most active. The catalytic activity of Fe-TiO2-PILC could be further improved by the addition of a small amount of cerium ions or cerium oxide. H2O and SO2 increase both the activity and the product selectivity to N2. The maximum activity on the Ce-Fe-TiO2-PILC is more than 3 times as active as that on a vanadium catalyst. Moreover, compared to the V2O5-WO3/TiO2 catalyst, the Fe-TiO2-PILC catalysts show higher N2/N2O product selectivities and substantially lower activities (by approximately 85%) for SO2 oxidation to SO3 under the same reaction conditions. A 100-hr run in the presence of H2O and SO2 for the CeO2/Fe-TiO2-PILC catalyst showed no decrease in activity.     

Noble metal catalysts for methane removal

Using a bench-scale rig, the activities of Pt, Pd and Pt+Pd catalysts supported on gamma-Al(2)O(3) and on TiO(2) (anatase) for the complete oxidation of methane (300 ppmv) in air have been measured as a function of temperature; values of T(10), T(50) and T(90) together with the Arrhenius parameters (activation energy and pre-exponential factor) are reported. Pt is less active than Pd when deposited on the surface of the TiO(2), but more active when deposited on gamma-Al(2)O(3), however when combined, the Pt+Pd mixture is more active than either metal individually. The T(10) for Pt+Pd/gamma-Al(2)O(3) was being as low as 228 degrees C. The significance of the Arrhenius parameters, for metal containing catalysts is that they exhibit compensation with increasing activation energy, while securing a more rapid increase in conversion from 0% to 100% when the temperature is increased.     

H2O和SO2对V2O5-WO3/TiO2催化剂催化氧化NO的影响

研究了在120℃的反应温度下,H2O和SO2对V2O5-WO3/TiO2催化剂选择性催化氧化（SCO）NO的影响。结果表明,在H2O和SO2存在的情况下催化剂失活很快,停止通入H2O和SO2后活性不能恢复,但在加热到250℃后催化活性基本恢复。FT-IR分析表明,催化剂表面形成了金属硝酸盐和Ti的硫酸盐,对催化活性有一定影响,但不影响催化剂在250℃下催化活性的恢复。SO2、H2O和NO的竞争吸附与SO2和NO2的铅室反应是影响催化剂活性的主要原因。     

Promotional effect of ZrO2 and WO3 on bimetallic Pt-Pd diesel oxidation catalyst

Environmental Science and Pollution Research - Diesel oxidation catalysts Pt-Pd-(y)ZrO2-(z)WO3/CeZrOx-Al2O3 with total Pt & Pd loading of only 0.68 wt.% were prepared and investigated for...     

Catalytic performance of Ag/Al2O3-C2H5OH-Cu/Al2O3 system for the removal of NOx from diesel engine exhaust

The selective catalytic reduction (SCR) of NOx by C(2)H(5)OH was studied in excess oxygen over Ag/Al(2)O(3) catalysts with different Ag loadings at lab conditions. The 4% Ag/Al(2)O(3) has the highest activity for the C(2)H(5)OH-SCR of NOx with a drawback of simultaneously producing CO and unburned THC in effluent gases. An oxidation catalyst 10% Cu/Al(2)O(3) was directly placed after the Ag/Al(2)O(3) to remove CO and unburned THC. Washcoated honeycomb catalysts were prepared based on the 4% Ag/Al(2)O(3) and 10% Cu/Al(2)O(3) powders and tested for the C(2)H(5)OH-SCR of NOx on a diesel engine at the practical operating conditions. Compared with the Ag/Al(2)O(3) powder, the Ag/Al(2)O(3) washcoated honeycomb catalyst (SCR catalyst) has a similar activity for NOx reduction by C(2)H(5)OH and the drawback of increasing the CO and unburned THC emissions. Using the SCR+Oxi composite catalyst with the optimization of C(2)H(5)OH addition, the diesel engine completely meets EURO III emission standards.     

Performance of the supported copper oxide catalysts for the catalytic incineration of aromatic hydrocarbons

A fixed bed reactor was used to assess the catalytic incineration of toluene by various transition-metal oxide species supported on gamma-Al(2)O(3). CuO/gamma-Al(2)O(3) was found to be the most active of seven catalysts investigated. The CuO species, with a Cu content of 5% (wt), was hence used with four different supports (CeO(2), gamma-Al(2)O(3), TiO(2) and V(2)O(5)) in order to define the optimal combination. Results of the catalytic incineration of toluene, X-ray diffraction (XRD) analysis, oxygen-temperature programmed desorption (O(2)-TPD), toluene-temperature programmed desorption (toluene-TPD) and hydrogen-temperature programmed reduction (H(2)-TPR) showed that CuO/CeO(2) was the most active catalyst, followed by CuO/gamma-Al(2)O(3). The activity of CuO/CeO(2) with respect to the VOC molecule was observed to follow this sequence: toluen>p-xylene>benzene. The addition of water vapor or CO(2) significantly inhibited the activity of the CuO/CeO(2) and CuO/gamma-Al(2)O(3) catalysts. The inhibiting effect of both was reversible for CuO/gamma-Al(2)O(3). For CuO/CeO(2), the inhibiting effect of CO(2) was reversible and even insignificant at a higher temperature (220 degrees C), but the effect of H(2)O vapor was somewhat irreversible at lower incineration temperatures (220 degrees C). For complete oxidation of toluene, the required reaction temperature increased with gas hourly space velocity (GHSV) and toluene inlet concentration.     

Photocatalytic oxidation of NOx using composite sheets containing TiO2 and a metal compound

The photocatalytic oxidation of nitrogen oxides (NO(x)) over titanium dioxide (TiO(2)) sheets containing metal compounds (MCs) had been studied. Calcium oxide (CaO), magnesium oxide (MgO), calcium carbonate (CaCO(3)), aluminium oxide (Al(2)O(3)) and ferric oxide (Fe(2)O(3)) were used as MCs. Al(2)O(3) and Fe(2)O(3) added to the TiO(2) sheet did not affect the photooxidation of nitrogen oxides (NO(x)). The CaO sheet treated with TiO(2) sol had the greatest efficiency as a NO(x) remover under UV irradiation. It is believed that CaO has a high adsorptivity for nitrogen dioxide (NO(2)) and nitric acid (HNO(3)). The amount of NO(x) removed by a TiO(2) sheet including MC showed a tendency to increase with increasing pH of the MC suspension, i.e. there is a good correlation between the alkalinity of the MC and the retention of NO(2) and HNO(3).     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

还原剂对Ag/Al2O3催化剂上NO还原的影响

在富氧条件下,研究了CH4、C3H8、C 3H6、C8H18、CH 3OH、C2H5OH,以及C3H6与CH3OH、C3H6与C2H5OH组合作还原剂时,在Ag/Al2O3催化剂上NO的还原活性.结果表明,不同碳氢化合物还原NO的活性温度存在较大的差异.SO2的存在会导致CH3OH还原NO的活性提高,而其他碳氢化合物还原NO的活性降低.随着还原剂浓度提高,NOx转化率增大,不过,过高的还原剂浓度对NO还原不利.组合使用CH3OH与C3H6或C2H5OH与C3H6作为还原剂,能显著拓宽活性温度范围.     

鼓泡反应器中液相络合催化同时脱硫脱硝的研究

在鼓泡反应器中考察了[Co(en)3]2+同时吸收去除SO2和NO的影响因素,实验结果表明,pH值和脱硫剂种类是影响乙二胺合钴同时脱除NO和SO2的最重要影响因素,烟气中的氧促进乙二胺合钴吸收NO和SO2,烟气中的SO2,CO2和NO2对乙二胺合钴吸收NO具有抑制作用。在实验条件温度为20℃,pH为13.0,[Co(en)3]2+浓度为0.025 mol/L,加入1 g NH3.H2O的脱硝率更好,连续吸收60 min,脱硝率均保持在93.5%,加入NaOH和NH3.H2O的脱硫效果最好。乙二胺合钴络合同时脱除NO和SO2完全可以在一个装置中完成。     

Defining the photochemical contribution to particulate matter in urban areas using time-series analysis

The objective of this project is to demonstrate how the ambient air measurement record can be used to define the relationship between O3 (as a surrogate for photochemistry) and secondary particulate matter (PM) in urban air. The approach used is to develop a time-series transfer-function model describing the daily PM10 (PM with less than 10 microm aerodynamic diameter) concentration as a function of lagged PM and current and lagged O3, NO or NO2, CO, and SO2. Approximately 3 years of daily average PM10, daily maximum 8-hr average O3 and CO, daily 24-hr average SO2 and NO2, and daily 6:00 a.m.-9:00 a.m. average NO from the Aerometric Information Retrieval System (AIRS) air quality subsystem are used for this analysis. Urban areas modeled are Chicago, IL; Los Angeles, CA; Phoenix, AZ; Philadelphia, PA; Sacramento, CA; and Detroit, MI. Time-series analysis identified significant autocorrelation in the O3, PM10, NO, NO2, CO, and SO2 series. Cross correlations between PM10 (dependent variable) and gaseous pollutants (independent variables) show that all of the gases are significantly correlated with PM10 and that O3 is also significantly correlated lagged up to two previous days. Once a transfer-function model of current PM10 is defined for an urban location, the effect of an O3-control strategy on PM concentrations is estimated by calculating daily PM10 concentrations with reduced O3 concentrations. Forecasted summertime PM10 reductions resulting from a 5 percent decrease in ambient O3 range from 1.2 microg/m3 (3.03%) in Chicago to 3.9 microg/m3 (7.65%) in Phoenix.     

Modification of carbon-coated TiO2 by iron to increase adsorptivity and photoactivity for phenol

Carbon-coated TiO(2) modified by iron, were prepared from TiO(2) of anatase structure and PET modified by FeC(2)O(4). Catalysts were prepared by mixing powders of TiO(2) and modified PET and heating at different temperatures, from 400 to 800 degrees C under flow of Ar gas. High adsorption of phenol was observed on the catalyst heated at 400 degrees C, confirmed by FT-IR analysis. On this catalyst, fast rate of phenol decomposition was achieved by addition of small amount of H(2)O(2) to the reaction mixture. Phenol decomposition proceeded mainly through the direct oxidation of phenol species adsorbed on the catalyst surface due to the photo-Fenton reaction. Iron-modified carbon-coated TiO(2) catalysts heated at 500-800 degrees C showed almost no phenol adsorption or oxidation.     

Study on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos

In this paper, dichromate and dichlorvos are selected as the deputies of inorganic and organic pollutants, respectively, and TiO2/beads is used as a photocatalyst. The effects of various parameters, such as the amount of the photocatalyst, H2O2 concentration, metal ions, anions, pH value, and organic compounds on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos are studied. From the studies, the differences of the parameters effect on the photocatalytic degradation of organic and inorganic pollutants are obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g cm(-3) for the photocatalytic reactions. With the addition of a small amount of H2O2, the photocatalytic reduction of dichromate is inhibited while the photocatalytic oxidation of dichlorvos is accelerated. With the addition of trace amounts of Fe3+ or Cu2+, both the reactions are accelerated, and with the addition of Zn2+ and Na+, no obvious effects on the reactions are observed. Acidic solution is favorable for the photocatalytic reduction of dichromate; and acidic and alkaline solutions are favorable for the photocatalytic oxidation of dichlorvos. Adding SO4(2-), the photocatalytic oxidation is accelerated and adding Cl- the reaction is inhibited; and with the addition of trace amounts of SO4(2-), Cl- and NO3-, no obvious effects on the photocatalytic reduction of dichromate are observed. With the addition of methanol and toluene, the photocatalytic reduction of dichromate is accelerated, and the photocatalytic oxidation of dichlorvos is inhibited. The possible roles of the additives on the reactions are also discussed.     

Ti-Ce-Zr-Ox复合脱硝催化剂的制备及其性能研究

采用共混法制备了Ti-Ce-Zr-Ox复合脱硝催化剂TiCe0.1Zr0.1O2.4,运用X射线衍射、氮气物理吸附、扫描电镜等表征手段,分别对该催化剂的晶型、表面积、孔分布及结构形貌进行了分析,同时考察了反应温度、空速、水蒸气和SO2对该催化剂NH3选择性催化还原NO的影响.结果表明,TiCe0.1Zr0.1O2.4催...