化学沉淀法去除焦化废水中的氨氮

采用化学沉淀剂MgCl2 ·6H2 O和Na2 HPO4·12H2 O(或MgHPO4·3H2 O)与焦化废水中的NH+ 4 反应 ,生成磷酸铵镁沉淀。探讨了不同操作条件对氨氮去除率的影响。在pH为 8 5～ 9 5的条件下 ,投加的药剂Mg2 + ∶NH+ 4 ∶PO3 -4(摩尔比 )为 1 4∶1∶0 8时 ,废水氨氮的去除率达 99%以上 ,出水氨氮的质量浓度由 2 0 0 0mg/L降至 15mg/L。     

Fenton试剂氧化—SBR工艺处理阿莫西林制药废水生化处理出水

采用Fenton试剂氧化—SBR工艺处理阿莫西林制药废水生化处理出水。实验结果表明:当初始废水pH为3.0、H2O2加入量为10 mL/L、V(H2O2):m(FeSO4.7H2O)为5(mL):1(g)、Fenton试剂氧化反应时间为3 h时,Fenton试剂氧化COD去除率达72.25%,色度由100倍降为2倍,BOD5/COD由0.06提高到0.38,可生化性显著提高。经Fenton试剂氧化—SBR工艺处理后,出水COD为72.7 mg/L,达到国家排放标准。     

多级冷冻法处理含油废水

采用多级冷冻法处理含油废水。实验结果表明:在初始废水中COD和ρ(NH3-N)分别为36 400 mg/L和73 mg/L的条件下,经过8级冷冻处理,COD和ρ(NH3-N)分别降至430 mg/L和2 mg/L,去除率分别可达98.82%和97.72%;在相同COD的条件下,ρ(NH3-N)较高时,COD去除率较高,由此可见无机盐离子(如NH4+)的存在有利于有机物的去除。     

强化厌氧生物技术在印染废水处理中的应用

采用三级厌氧柱串联形成的递进式强化厌氧处理工艺协同Fenton氧化工艺处理某印染厂的印染废水(COD 1 418 mg/L、色度400倍)。三级厌氧柱的运行参数为:以陶粒为填料,进水p H为7.0,3个厌氧柱的HRT均为16 h,柱温(33±2)℃。厌氧柱2的强化条件为投加280 mg/L钙离子和30 mg/L PAM,厌氧柱3的强化条件为投加350 mg/L煤质活性炭。三级厌氧柱强化前后的COD去除率分别为70.38%和84.13%,色度去除率分别为50.00%和62.50%。Fenton氧化处理的最佳条件为H2O2投加量450 mg/L、Fe SO4投加量450 mg/L、反应p H 3.5、反应时间0.5 h。整个工艺的总COD去除率达96.12%、总色度去除率达78.75%,处理后出水的COD为55 mg/L、色度为85倍,满足GB 4287—2012《纺织染整工业水污染物排放标准》中的直排标准。     

A/O—Fenton氧化—混凝组合工艺处理丁苯橡胶生产废水

采用A/O—Fenton氧化—混凝组合工艺处理丁苯橡胶生产废水。试验结果表明:A/O工段中,在兼氧池HRT 8 h、好氧池HRT 16 h、好氧池MLSS 2 500~3 500 mg/L的优化参数下,平均COD,NH3-N,TP去除率分别为72.9%,96.2%,51.3%;Fenton氧化工段中,在30%(w)H2O2溶液加入量0.2%(φ)、n(H2O2)∶n(Fe SO4)=2∶1、Fenton氧化反应时间70 min、Fenton氧化进水p H 5.0的优化条件下,COD和TP的去除率分别为56.0%和57.0%;A/O—Fenton氧化—混凝组合工艺对COD、NH3-N、TP、浊度的总去除率分别为94.8%,96.2%,100%,94.0%,处理后出水满足GB 8978—1996《污水综合排放标准》中的一级标准。     

化学沉淀法去除煤气废水中氨氮的研究

采用化学沉淀法去除煤气废水中的氨氮。研究了不同pH、沉淀剂种类及投药比对氨氮去除效果的影响。试验表明,沉淀剂MgCl2·6H2O+Na2HPO4·12H2O明显优于MgO+H3PO4。当投药摩尔比n(Mg2+):n(NH4+):n(PO43-)为1.2:1:1、pH为9.5时,废水中氨氮的去除率为87.4％,COD的去除率为45.6％,同时得到的MgNH4PO4·6H2O可作为复合肥料使用。     

零价铁/炭纤维预处理制药废水

以炭纤维为载体,采用电沉积法制备零价铁/炭纤维,考察了零价铁/炭纤维对制药废水COD的去除效果。SEM表征结果显示,炭纤维表面光滑,炭纤维上负载的零价铁呈现大小不一的球状。实验结果表明:在初始废水p H为5、铁碳质量比为2∶1、固液比(固体质量以铁计)为90 g/L、曝气量为80 L/h的条件下,采用零价铁/炭纤维体系处理COD=10 082.63 mg/L、色度为135倍、p H=7.3、SS=250 mg/L、Na Cl质量分数为3.5%的制药废水,COD去除率可达72.79%,出水COD为2 743.48 mg/L,减轻了后续生化处理工艺的进水负荷;零价铁/炭纤维降解制药废水中COD的过程符合三级反应动力学方程。     

微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水

采用微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水,优化了工艺条件。实验结果表明:最佳工艺条件为初始废水p H 3.0、铁屑加入量1.5 g/L(铁屑与活性炭的质量比1∶1)、微电解时间80 min、Fenton氧化时间120 min、H2O2加入量940 mg/L,阳离子聚丙烯酰胺加入量120 mg/L;在最佳工艺条件下处理废水后,COD由3116.0 mg/L降至681.3 mg/L,总COD去除率达78.1%,3个工段的COD去除率依次为33.1%,37.9%,7.1%,出水水质满足现场回注标准(SY/T 5329—2012《碎屑岩油藏注水水质推荐指标及分析方法》);该组合工艺对废水的处理效果远优于单独微电解、Fenton氧化或絮凝工艺,且方法简单易行、药剂利用率高。     

Fenton试剂氧化—原水调节出水pH法预处理碱性印染废水

采用Fenton试剂氧化—原水调节出水pH法预处理碱性印染废水,考察了n(H2O2):n(Fe2+)、Fenton试剂加入量、反应时间和原水与Fenton试剂氧化反应后出水体积比(配水比)对COD去除率及废水pH的影响.实验结果表明,在原水COD为986 mg/L、原水pH为9.31、Fe2+加入量为12 mmol/L、n(H2O2):n(Fe2+)为2、反应时间为30 min、配水比为2的最佳条件下,COD去除率为26.9％,出水pH为6.60.药剂成本较普通Fenton试剂氧化法减少70％.     

大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯废水

采用大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯(DIBP)废水。大孔树脂吸附工段的最佳实验条件为:以树脂NDA88为吸附剂,废水pH为2。NDA88经过10批次的连续使用,COD去除率基本稳定在58%左右,脱附率可达96%以上,吸附后废水COD为12 000 mg/L左右。Fenton试剂氧化工段的最佳实验条件为:H2O2加入量70 mL/L,n(H2O2):n(Fe2+)=4,废水pH 4。在此最佳条件下进行实验,Fenton试剂氧化工段COD去除率达65%,处理后废水COD为4 200 mg/L。     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Effect of depth of landfill on the characteristics of soil-like material of aged waste: a case study of Bhalswa dumpsite,India

Journal of Material Cycles and Waste Management - This study characterizes the municipal solid waste (MSW) accumulated for more than 25 years at Bhalswa dumpsite, Delhi, India. 50...     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％;靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.