含锰氧化物的陶粒催化臭氧氧化苯甲酸废水

分别以含锰氧化物的陶粒和普通陶粒为填料,以O_3体系和催化剂体系作为参照,研究臭氧在填料的异相催化条件下对苯甲酸的去除效果。结果表明:O_3/催化剂体系具有更好的催化效果,同时O_3/催化剂体系可有效改善废水的可生化性,并减少臭氧投加量和处理成本;初始pH为7~12时,废水的苯甲酸去除效果较好,且O_3/催化剂体系的臭氧利用率比O_3/普通陶粒体系、空柱的臭氧利用率更高,在初始pH为7时O_3/催化剂体系的臭氧利用率提升效果最显著。     

催化强化臭氧氧化处理化工园区生化尾水

以陶粒为载体,以Ti O2,Fe2O3,Mn O2为活性组分,考察不同活性组分的陶粒作为催化剂对化工园区生化尾水臭氧氧化能力的强化情况。结果表明,3种负载型催化剂均能有效强化臭氧氧化过程,显著降低生化尾水Abs、UV254以及COD等指标,其中以Fe2O3/陶粒的催化强化效果最为显著,能显著降低生化尾水在200~250 nm处的吸波强度,尾水UV254从0.580降至0.320,COD从240 mg/L降至194 mg/L。     

钢渣污泥陶粒催化剂催化臭氧深度处理炼油废水

采用固相混合法制备了钢渣污泥陶粒催化剂,SEM、XRD测试结果显示,催化剂具有较为发达的孔隙结构,活性组分以MnO_2和CuO晶型形态分布于陶粒中。对含盐炼油废水生化尾水进行了臭氧催化氧化研究,考察了废水初始pH、催化剂用量、臭氧投加量等因素对COD去除效果的影响。结果表明,当反应初始pH为7.36、催化剂用量为15 g·L~(-1)、臭氧投加量为4.21 mg·min~(-1)时,反应35 min,废水中COD从86.97 mg·L~(-1)降至48.02 mg·L~(-1),出水水质达到新修订的《石油炼制工业污染物排放标准》。所制备的催化剂活性稳定、使用寿命长,活性组分锰、铜溶出率低,无二次污染产生。     

臭氧-曝气生物滤池深度处理印染制革园区废水

针对浙江省某印染制革园区污水处理厂二级生化出水,开展了处理规模36~120 t/d的臭氧-曝气生物滤池中试研究,对臭氧预处理进行优化,考察了臭氧预处理优化后与不同填料BAF组合对污染物的去除情况。结果表明,当臭氧预处理条件为投加量25 mg/L,三点投加且投加比为6：3：1,臭氧接触时间为42 min时,处理效果较好且最经济;在此臭氧预处理条件下,臭氧-活性炭BAF的出水COD能稳定在50 mg/L,色度稳定在5度,满足《城镇污水厂污染物排放标准》（GB 18918-2002）中的一级B排放要求;臭氧-混合填料BAF的出水COD和色度也能基本达到一级B排放要求;而臭氧-陶粒BAF出水COD和色度都未能达到一级B排放要求。     

臭氧-催化技术治理低浓度气体污染物

在对臭氧－催化技术及其发展现状评述的基础上,分别考察了铂－钯催化剂（Pt-Pd/Al2O3）对DMMP、CH4、C6H6、F22、CO催化氧化和臭氧催化 氧化的反应性能。结果表明,催化作用和臭氧催化氧化作用所要求的反应温度范围相近并低于250℃,才能很好地协同作用。臭氧－催化技术竽起燃温度低、易氧化气体污染物的处理。     

煤化工高盐废水臭氧催化氧化脱除COD

针对煤化工高盐废水中有机物难降解问题,采用浸渍-煅烧法制备了负载有活性金属氧化物的活性氧化铝型催化剂,探索催化剂的制备工艺和反应操作条件对废水COD去除率的影响。结果表明:活性氧化铝载体催化性能优于陶粒,活性氧化铝负载Cu、Mn、Ni的催化活性较高,将2种活性组分进行组合制得的MnO_xNiO_x/γ-Al_2O_3催化剂,在经过60 min的臭氧催化氧化后,COD的去除率可达51.3%;利用BET、SEM-EDS、XRD对催化剂进行了表征和分析,Mn、Ni成功负载到活性氧化铝表面和孔隙内,2种元素负载量摩尔比约为2:1,且主要以氧化物形式存在;通过计算臭氧利用效率,发现MnO_x-NiO_x/γ-Al_2O_3臭氧催化氧化的_η值低于单独的臭氧氧化,这意味着通过MnO_x-NiO_x/γ-Ak_2O_3催化剂可以有效地将臭氧分解成活性氧;通过优化臭氧和催化剂投加量后发现,在臭氧为350 mg·(L·h)~(-1)、催化剂投加量为100 g·L~(-1)废水中,反应180 min后,COD去除率可达到72.3%;在连续进行4 h的臭氧催化氧化实验后,MnO_x-NiO_x/γ-Al_2O_3稳定性和重复利用性均较好,COD去除率能维持在约42%,锰、镍离子的溶出量均小于0.5 mg·L~(-1)。以上研究结果可为高效的臭氧催化体系在煤化工高盐废水处理领域的应用提供参考。     

自来水厂污泥制得陶粒对污水中磷和氨氮的吸附

自来水厂在制水过程中使用了铝系、铁系无机混凝剂,故而污泥中含有较多的铝、铁成分。本研究从固体废物综合利用角度,结合自来水厂污泥成分特点,探索自来水厂污泥陶粒化后作为污水处理污染物吸附填料的可行性。通过对四种不同温度条件下煅烧制得陶粒填料的污染物吸附性能及物理化学特征的对比研究表明,4种陶粒填料对磷均有较好的吸附效果,其中以400℃条件下制得的吸附效果最好,去除率可达98%;EDS、XRD等物化表征显示了4种陶粒填料中均含有铝的氧化物,但纯度不高,含量因煅烧温度不同而有所不同,800℃条件下制得的最低;比较吸附前后填料中Al-P的含量变化,400℃条件下制得的陶粒填料Al-P吸附量最大,达448.23 mg/kg,而800℃的最低,仅为116.11 mg/kg,煅烧后陶粒中铝氧化物是这类陶粒填料对磷吸附效果主要因素。     

臭氧知识普及在天是佛,在地是魔

正"在天是佛,在地是魔",是科学界对臭氧的概括。人类生活中接触到的臭氧主要分为两类:臭氧层臭氧和近地面臭氧。臭氧层臭氧存在于距离地面15~25 km的高层大气中,能阻挡大部分太阳光中的紫外线对地表生物的伤害,是地球生命的"保护伞"。由于人类过多地使用氯氟烃类化学物质(CFCs)、哈龙类物质等,使臭氧层臭氧遭到破坏。臭氧层臭氧的耗竭会使太阳光中的紫外线     

给水厂与污水厂污泥制陶粒技术研究

对天津凌庄自来水厂的给水厂污泥和天津东郊污水处理厂的污水厂污泥的成分进行了分析,在此基础上根据焙烧陶粒的原理,设计了以2种污泥为原料焙烧陶粒的工艺流程。通过实验,研究了其工艺过程中的影响因素并确定了工艺参数。性能检验结果表明,添加量为30％的混合污泥陶粒,在1 140℃焙烧5 min,可得到强度标号为40 MPa的高强陶粒。因此,以2种污泥为原料烧制陶粒的处置方法可行,并能带来一定的经济效益、社会效益和环境效益。得到的产品符合国标中高强陶粒的要求,可广泛应用于建筑行业中的承重结构。     

优质页岩陶粒滤料的制备与基本性能研究

以天然页岩为原料,分别采用破碎法和成球法制成滤料生料,经焙烧,膨胀,制备了陶粒滤料.对这2种方法制备的陶粒滤料的孔隙率、孔径和酸碱可溶率等指标进行了分析比较.结果表明,2种方法均可制备出性能优异的陶粒滤料.陶粒滤料的制备方法对其性能影响不大,而焙烧程序对陶粒滤料的性能有较大影响.实际生产时,可根据页岩特性、生产成本等确定陶粒滤料的制备方法.     

Investigation on the effect of sintering temperature on kaolin hollow fibre membrane for dye filtration

Despite its extraordinary price, ceramic membrane can still be able to surpass polymeric membrane in the applications that require high temperature and pressure conditions, as well as harsh chemical environment. In order to alleviate the high cost of ceramic material that still becomes one of the major factors that contributes to the high production cost of ceramic membrane, various attempts have been made to use low cost ceramic materials as alternatives to well-known expensive ceramic materials such as alumina, silica, and zirconia in the fabrication of ceramic membrane. Thus, local Malaysian kaolin has been chosen as the ceramic material in this study for the preparation of kaolin hollow fibre membrane since it is inexpensive and naturally abundant in Malaysia. Due to the fact that the sintering process plays a prominent role in obtaining the desired morphology, properties, and performances of prepared ceramic membrane, the aim of this work was to study the effect of different sintering temperatures applied (ranging from 1200 to 1500 °C) in the preparation of kaolin hollow fibre membrane via dry/wet phase inversion-based spinning technique and sintering process. The morphology and properties of membrane were then characterised by SEM, AFM, FTIR, XRD, and three-point bending test, while the performances of membrane were investigated by conducting water permeation and Reactive Black 5 (RB5) dye rejection tests. From the experimental results obtained, the sintering temperature of 1400 °C could be selected as the optimum sintering temperature in preparing the kaolin hollow fibre membrane with the dense sponge-like structure of separation layer that resulted in the good mechanical strength of 70 MPa with the appreciable water permeation of 75 L/h m² bar and RB5 rejection of 68%.     

Evaluation of ceramic and membrane diffusers under operating conditions with the dynamic offgas method.

The aeration systems of two full-scale, activated-sludge basins were compared during a period of three years, under the same operating conditions, using dynamic offgas testing. Only the material of the diffuser was different (membrane versus ceramic-tube diffusers). The investigation has shown that, although the membrane diffusers have higher initial standard-oxygen-transfer efficiency (alphaSOTE) and standard-aeration efficiency (alphaSAE), these decreased over time, while the alphaSAE of the ceramic diffusers started lower, but increased slightly over the whole period. A cost comparison makes clear how important it is to evaluate the aeration system under process conditions. The operating costs were the dominant factor (approximately 10x higher than capital costs), and operating costs were approximately 20% higher for membrane versus ceramic diffusers. The poor performance of the membrane-tube diffusers under process conditions could be explained on the basis of the actual alphaAE values in the basin, not the standardized values.     

Concentrations of polychlorinated dibenzo-p-dioxins in processed ball clay from the United States

Processed ball clays commonly used by the ceramic art industry in the United States were collected from retail suppliers and analyzed for the presence and concentration of the 2,3,7,8-Cl substituted polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs). The average PCDD toxic equivalent (TEQ) concentrations of these processed ball clays was approximately 800 pg/g (TEQ-WHO) with characteristic congener profiles and isomer distributions similar to patterns of previously analyzed raw and processed ball clays. The PCDF concentrations were below the average limit of detection (LOD) of 0.5 pg/g. Correlation analyses reveal no significant relationship between total organic carbon (TOC) and either individual, homologues, and total tetra-through octa-chlorinated PCDD congeners, or TEQ concentrations of the processed ball clays. The results are consistent with earlier studies on levels of PCDDs in ball clays. Data from earlier studies indicated that dioxins may be released to the environment during the processing of raw clay or the firing process used in commercial ceramic facilities. The presence of dioxin in the clays also raises concerns about potential occupational exposure for individuals involved in the mining/processing of ball clay, ceramics manufacturing and ceramic artwork.     

混凝沉淀前处理对丙烯酸丁酯废水陶瓷膜过滤膜污染的影响

采用混凝沉淀-双层滤料过滤-陶瓷膜过滤组合工艺去除丙烯酸丁酯废水中浊度物质。结果表明,废水pH值、混凝药剂投加量、混凝沉淀水力条件不仅对丙烯酸丁酯废水混凝沉淀出水和双层滤料过滤单元出水浊度具有重要影响,而且对后续陶瓷膜过滤单元膜污染均具有重要影响。双层滤料过滤出水浊度与陶瓷膜污染阻力具有明显的正相关关系,双层滤料过滤出水浊度越高,陶瓷膜污染阻力越大。废水pH在7.0~10.0范围内、混凝药剂PAC或PAM投加过量、废水流量过高都会造成双层滤料过滤出水浊度偏高,导致陶瓷膜污染严重。     

Ceramic tiles with black pigment made from stainless steel plant dust: Physical properties and long-term leaching behavior of heavy metals

Stainless steel plant dust is a hazardous by-product of the stainless steelmaking industry. It contains large amounts of Fe, Cr, and Ni, and can be potentially recycled as a raw material of inorganic black pigment in the ceramic industry to reduce environmental contamination and produce value-added products. In this paper, ceramic tiles prepared with black pigment through recycling of stainless steel plant dust were characterized in terms of physical properties, such as bulk density, water absorption, apparent porosity, and volume shrinkage ratio, as well as the long-term leaching behavior of heavy metals (Cr, Ni, Pb, Cd, and Zn). The results show that good physical properties of ceramic tiles can be obtained with 8% pigments addition, sample preparation pressure of 25 MPa, and sintering at 1200 ºC for 30 min. The major controlling leaching mechanism for Cr and Pb from the ceramic tiles is initial surface wash-off, while the leaching behavior of Cd, Ni, and Zn from the stabilized product is mainly controlled by matrix diffusion. The reutilization process is safe and effective to immobilize the heavy metals in the stainless steel plant dust.

Implications: Stainless steel plant dust is considered as a hazardous material, and it can be potentially recycled for black pigment preparation in the ceramic industry. This paper provides the characteristics of the ceramic tiles with black pigment through recycling stainless steel plant dust, and the long-term leaching behavior and controlling leaching mechanisms of heavy metals from the ceramic tile. The effectiveness of the treatment process is also evaluated.     

MF-UF组合工艺处理再生纸废水的实验研究

针对再生纸废水体系,采用0.2 μm陶瓷微滤膜 （MF）与截留分子量为50 000 Dalton的疏水性PS有机超滤膜 （UF）组合工艺对再生纸废水进行处理。实验结果表明,此组合工艺对再生纸废水COD的去除率可达到846%,处理的废水达到造纸工业水污染物排放标准;根据再生纸废水的性质对膜清洗再生进行了考察,陶瓷膜及超滤膜通量约分别恢复85%与80%左右。     

陶瓷印花废水处理的混凝剂及工艺条件

采用混凝剂聚合氯化铝（PAC）、聚丙烯酰胺（PAM）、聚合硫酸铁（PFS）对陶瓷印花废水进行混凝沉降处理,监测水样的吸光度、浊度、悬浮物,以脱色率、浊度去除率、悬浮物去除率评价混凝处理的效果。结果表明：PAC是陶瓷印花废水沉降处理的理想混凝剂;水样的吸光度、浊度、悬浮物随混凝剂用量增大和沉降时间延长而呈降低趋势,而脱色率、浊度去除率、悬浮物去除率随混凝剂和沉降时间的增大呈增大的趋势;PAC投加量为20mg／L,沉降时间约为24h,水样脱色率达到90．0％,而当PAC投加量达到100mg／L,沉降时间约为4h,陶瓷印花水的脱色率可达到96．0％。证明了药剂用量的增加与沉降时间的延长对混凝过程具有增效作用。     

Role of expanded clay and porous ceramic amendments on plant establishment in minespoils

Greenhouse experiments were conducted to examine the impact of expanded clay (Turface) or porous ceramic (Isolite) amendments on germination, biomass production, plant Zn concentration, and Zn accumulation by Festuca arundinacea grown in mine tailings. Because previous studies have demonstrated that fertilization is essential for plant growth in these tailings, manure was also added to the tailings. Plant growth and germination were greatest if the expanded clay was added topically to the tailings. To a lesser extent, plant growth and germination was also stimulated by topical additions of porous ceramic. However, no benefit was observed if either amendment was mixed into the top 10 cm of the mine tailings. The concentration of Zn in F. arundinacea tissues was lowest if the expanded clay was added topically to the mine tailings. Roots growing in the layer of clay or ceramic amendment appeared to be smaller, finer, and more abundant than the large, coarse roots found throughout the tailings-manure mixture. These results suggest that topical application of an expanded clay or porous ceramic product will increase seed germination and improve plant establishment and growth in contaminated minespoils.     

Dibenzo-p-dioxins in the environment from ceramics and pottery produced from ball clay mined in the United States

Processed ball clay samples used in the production of ceramics and samples of the ceramic products were collected and analyzed for the presence and concentration of the 2,3,7,8-Cl substituted polychlorinated dibenzo-p-dioxins and -furans (PCDDs/PCDFs). The processed ball clay had average PCDD concentrations of 3.2 ng/g toxic equivalents, a congener profile, and isomer distribution consistent with those found previously in raw ball clay. The PCDF concentrations were below the average limit of detection (LOD) of 0.5 pg/g. The final fired ceramic products were found to be free of PCDDs/PCDFs at the LODs. A consideration of the conditions involved in the firing process suggests that the PCDDs, if not destroyed, may be released to the atmosphere and could represent an as yet unidentified source of dioxins to the environment. In addition, the PCDDs in clay dust generated during manufacturing operations may represent a potential occupational exposure.     

Dibenzo-p-dioxins in the environment from ceramics and pottery produced from ball clay mined in the United States

Processed ball clay samples used in the production of ceramics and samples of the ceramic products were collected and analyzed for the presence and concentration of the 2,3,7,8-Cl substituted polychlorinated dibenzo-p-dioxins and -furans (PCDDs/PCDFs). The processed ball clay had average PCDD concentrations of 3.2 ng/g toxic equivalents, a congener profile, and isomer distribution consistent with those found previously in raw ball clay. The PCDF concentrations were below the average limit of detection (LOD) of 0.5 pg/g. The final fired ceramic products were found to be free of PCDDs/PCDFs at the LODs. A consideration of the conditions involved in the firing process suggests that the PCDDs, if not destroyed, may be released to the atmosphere and could represent an as yet unidentified source of dioxins to the environment. In addition, the PCDDs in clay dust generated during manufacturing operations may represent a potential occupational exposure.