Assessing Calibration Uncertainty and Automation for Estimating Evapotranspiration from Agricultural Areas Using METRIC

Agricultural irrigation accounts for a large fraction of the total water use in the western United States. The Mapping Evapotranspiration at high Resolution with Internalized Calibration (METRIC) remote sensing energy balance model is being used to estimate historical agricultural water use in western Nevada to evaluate basin‐wide water budgets. Each METRIC evapotranspiration (ET) estimate must be calibrated by a trained user, which requires some iterative time investment and results in variation in ET estimates between users. An automated calibration algorithm for the METRIC model was designed to generate ET estimates comparable to those from trained users by mimicking the manual calibration process. Automated calibration allows for rapid generation of METRIC ET estimates with minimal manual intervention, as well as uncertainty and sensitivity analysis of the model. The variation in ET estimates generated by the automated calibration algorithm was found to be similar to the variation in manual ET estimates. Results indicate that uncertainty was highest for fields with low ET levels and lowest for fields with high ET levels, with a seasonal mean uncertainty of approximately 5% for all fields. In addition, in a blind comparison, automated daily and seasonal ET estimates compared well with flux tower measurement ET data at multiple sites. Automated methods can generate first‐order ET estimates that are similar to time intensive manual efforts with less time investment.     

Sensitivity of Landsat‐Scale Energy Balance to Aerodynamic Variability in Mountains and Complex Terrain

The speed and direction of air flow through complex terrain are difficult to define. Both impact sensible and latent heat flux exchanges at the surface. Evapotranspiration (ET) models such as Mapping EvapoTranspiration at high Resolution with Internalized Calibration (METRIC?) estimate ET as a residual of the surface energy process and are thus sensitive to aerodynamics, including terrain‐induced impacts on roughness governing convective heat transfer (H). There is a need to explore the sensitivities of H estimation and thereby ET estimation to wind speed and terrain roughness in mountainous areas and to determine the merit of operating complex mesoscale wind field models in conjunction with the energy balance process. A sensitivity analysis is explored in METRIC where we increased wind speed in proportion to a relative elevation parameter and we increased aerodynamic roughness to assimilate impacts of relative terrain roughness, estimated in proportion to standard deviation of elevation within a 3 km locality. These aerodynamic modifications increased convective heat transfer in complex terrain and reduced estimated ET. In other sensitivity runs, we reduced estimated wind speed on estimated leeward slopes. Estimated ET with and without these sensitivity adjustments is shown for mountainous areas of Montana and Nevada. Changes in ET ranged from little change (<5%) for lower slopes to about 30% reductions on windward slopes and 25% increases on leeward slopes for some mid to high elevations in the Montana application.     

Global Daily Reference Evapotranspiration Modeling and Evaluation1

Abstract: Accurate and reliable evapotranspiration (ET) datasets are crucial in regional water and energy balance studies. Due to the complex instrumentation requirements, actual ET values are generally estimated from reference ET values by adjustment factors using coefficients for water stress and vegetation conditions, commonly referred to as crop coefficients. Until recently, the modeling of reference ET has been solely based on important weather variables collected from weather stations that are generally located in selected agro‐climatic locations. Since 2001, the National Oceanic and Atmospheric Administration’s Global Data Assimilation System (GDAS) has been producing six‐hourly climate parameter datasets that are used to calculate daily reference ET for the whole globe at 1‐degree spatial resolution. The U.S. Geological Survey Center for Earth Resources Observation and Science has been producing daily reference ET (ETo) since 2001, and it has been used on a variety of operational hydrological models for drought and streamflow monitoring all over the world. With the increasing availability of local station‐based reference ET estimates, we evaluated the GDAS‐based reference ET estimates using data from the California Irrigation Management Information System (CIMIS). Daily CIMIS reference ET estimates from 85 stations were compared with GDAS‐based reference ET at different spatial and temporal scales using five‐year daily data from 2002 through 2006. Despite the large difference in spatial scale (point vs. ～100 km grid cell) between the two datasets, the correlations between station‐based ET and GDAS‐ET were very high, exceeding 0.97 on a daily basis to more than 0.99 on time scales of more than 10 days. Both the temporal and spatial correspondences in trend/pattern and magnitudes between the two datasets were satisfactory, suggesting the reliability of using GDAS parameter‐based reference ET for regional water and energy balance studies in many parts of the world. While the study revealed the potential of GDAS ETo for large‐scale hydrological applications, site‐specific use of GDAS ETo in complex hydro‐climatic regions such as coastal areas and rugged terrain may require the application of bias correction and/or disaggregation of the GDAS ETo using downscaling techniques.     

Evapotranspiration in the Meso‐Scale Forested Watersheds in Minjiang Valley,West China1

Abstract: Information on evapotranspiration (ET) can help us understand water balance, particularly in forested watersheds. Previous studies in China show that ET was relatively low (30‐40% of total precipitation) in the Minjiang Valley located in the upper reach of the Yangtze River Basin. However, this conclusion was derived from research on small‐scale watersheds (<100 km²). The objective of this paper was to present ET information on meso‐scale watersheds in the Minjiang Valley. Four meso‐scale watersheds (1,700‐5,600 km²) located in the Minjiang Valley were used to estimate ET using the water balance approach. We first generated forest vegetation variables (coniferous forest percentage, forest cover percentage, and derived forest vegetation index) using remote sensing data. Landsat 5 TM satellite images, acquired on June 26, 1994, were selected for the vegetation classification. Actual annual ET was calculated based on 11‐year estimated precipitation and measured streamflow data (1992‐2002). We also calculated potential ET (PET) using an improved Thornthwaite model for all four watersheds for the period of 1992‐1998. PET can provide additional information about potential capacity of water flux to atmosphere in the region. Seasonal (dry and rainy) PET and ET for all studied watersheds were also estimated for comparison purposes as the water balance approach, at shorter than annual scales, would likely provide inaccurate estimates of ET. The dominant vegetations in the Minjiang Valley were grasslands, conifer forests, and shrub‐lands. Our results confirmed that both ET and PET for three studied meso‐scale watersheds in the Minjiang Valley is relatively low (39.5‐43.8 and 28.2‐47.7% for ET and PET, respectively), with an exception of ET in the Yuzixi watershed being 71.1%. This result is generally consistent with previous research at small watershed scales. Furthermore, the low ET across various scales in the Minjiang Valley may be related to the unique deeply cut valley environment.     

Management Implications of Snowpack Sensitivity to Temperature and Atmospheric Moisture Changes in Yosemite National Park,CA

In order to investigate snowpack sensitivity to temperature increases and end‐member atmospheric moisture conditions, we applied a well‐constrained energy‐ and mass‐balance snow model across the full elevation range of seasonal snowpack using forcing data from recent wet and dry years. Humidity scenarios examined were constant relative humidity (high) and constant vapor pressure between storms (low). With minimum calibration, model results captured the observed magnitude and timing of snowmelt. April 1 snow water equivalent (SWE) losses of 38%, 73%, and 90% with temperature increases of 2, 4, and 6°C in a dry year centered on areas of greatest SWE accumulation. Each 2°C increment of warming also resulted in seasonal snowline moving upslope by 300 m. The zone of maximum melt was compressed upward 100–500 m with 6°C warming, with the range reflecting differences in basin hypsometry. Melt contribution by elevations below 2,000 m disappeared with 4°C warming. The constant‐relative‐humidity scenario resulted in 0–100 mm less snowpack in late spring vs. the constant‐vapor‐pressure scenario in a wet year, a difference driven by increased thermal radiation (+1.2 W/m²) and turbulent energy fluxes (+1.2 W/m²) to the snowpack for the constant‐relative‐humidity case. Loss of snowpack storage and potential increases in forest evapotranspiration due to warming will result in a substantial shift in forest water balance and present major challenges to land management in this mountainous region.     

Spatiotemporal Evaluation of Simulated Evapotranspiration and Streamflow over Texas Using the WRF‐Hydro‐RAPID Modeling Framework

This study assesses a large‐scale hydrologic modeling framework (WRF‐Hydro‐RAPID) in terms of its high‐resolution simulation of evapotranspiration (ET) and streamflow over Texas (drainage area: 464,135 km²). The reference observations used include eight‐day ET data from MODIS and FLUXNET, and daily river discharge data from 271 U.S. Geological Survey gauges located across a climate gradient. A recursive digital filter is applied to decompose the river discharge into surface runoff and base flow for comparison with the model counterparts. While the routing component of the model is pre‐calibrated, the land component is uncalibrated. Results show the model performance for ET and runoff is aridity‐dependent. ET is better predicted in a wet year than in a dry year. Streamflow is better predicted in wet regions with the highest efficiency ~0.7. In comparison, streamflow is most poorly predicted in dry regions with a large positive bias. Modeled ET bias is more strongly correlated with the base flow bias than surface runoff bias. These results complement previous evaluations by incorporating more spatial details. They also help identify potential processes for future model improvements. Indeed, improving the dry region streamflow simulation would require synergistic enhancements of ET, soil moisture and groundwater parameterizations in the current model configuration. Our assessments are important preliminary steps towards accurate large‐scale hydrologic forecasts.     

How to Constrain Multi‐Objective Calibrations of the SWAT Model Using Water Balance Components

Accurate discharge simulation is one of the most common objectives of hydrological modeling studies. However, a good simulation of discharge is not necessarily the result of a realistic simulation of hydrological processes within the catchment. We propose an evaluation framework that considers both discharge and water balance components as evaluation criteria for calibration of the Soil and Water Assessment Tool (SWAT). In this study, we integrated average annual values of surface runoff, groundwater flow, and evapotranspiration in the model evaluation procedure to constrain the selection of good model runs for the Little River Experimental Watershed in Georgia, United States. For evaluating water balance and discharge dynamics, the Nash‐Sutcliffe efficiency (NSE) and percent bias (PBIAS) were used. In addition, the ratio of root mean square error and standard deviation of measured data (RSR) was calculated for individual segments of the flow duration curve to identify the best model runs in terms of discharge magnitude. Our results indicate that good statistics for discharge do not guarantee realistic simulations of individual water balance components. Therefore, we recommend constraining the ranges of water balance components to achieve a more realistic simulation of the entire hydrological system, even if tradeoffs between good statistics for discharge simulations and reasonable amounts of the water balance components are unavoidable. Editor's note : This paper is part of the featured series on SWAT Applications for Emerging Hydrologic and Water Quality Challenges. See the February 2017 issue for the introduction and background to the series.     

Quantifying Outdoor Water Consumption of Urban Land Use/Land Cover: Sensitivity to Drought

Outdoor water use is a key component in arid city water systems for achieving sustainable water use and ensuring water security. Using evapotranspiration (ET) calculations as a proxy for outdoor water consumption, the objectives of this research are to quantify outdoor water consumption of different land use and land cover types, and compare the spatio-temporal variation in water consumption between drought and wet years. An energy balance model was applied to Landsat 5 TM time series images to estimate daily and seasonal ET for the Central Arizona Phoenix Long-Term Ecological Research region (CAP-LTER). Modeled ET estimations were correlated with water use data in 49 parks within CAP-LTER and showed good agreement (r ² = 0.77), indicating model effectiveness to capture the variations across park water consumption. Seasonally, active agriculture shows high ET (>500 mm) for both wet and dry conditions, while the desert and urban land cover types experienced lower ET during drought (<300 mm). Within urban locales of CAP-LTER, xeric neighborhoods show significant differences from year to year, while mesic neighborhoods retain their ET values (400–500 mm) during drought, implying considerable use of irrigation to sustain their greenness. Considering the potentially limiting water availability of this region in the future due to large population increases and the threat of a warming and drying climate, maintaining large water-consuming, irrigated landscapes challenges sustainable practices of water conservation and the need to provide amenities of this desert area for enhancing quality of life.     

MODELING EFFECTS OF BRUSH MANAGEMENT ON THE RANGELAND WATER BUDGET: EDWARDS PLATEAU,TEXAS1

ABSTRACT: The Soil and Water Assessment Tool (SWAT) was used to evaluate the influence of woody plants on water budgets of semi‐arid rangelands in karst terrain. The model was configured for the hydrologic evaluation of the North Fork of the Upper Guadalupe River watershed and was calibrated and verified using measured flow data. Nash and Sutcliffe fit efficiencies for daily and monthly verification periods were 0.09 and 0.50, respectively. Streamflow, baseflow, and evapotranspiration (ET) rates were comparable to published field data. Simulated deep recharge was considerably higher than the published values for the Edwards Plateau. The model was then used to simulate conditions with existing brush cover and four different brush removal scenarios. Scenarios were created to represent existing brush and the removal of brush from only locations that were either covered by heavy brush, were on a moderate slope, or were in shallow soils. Resulting data was compared to previous studies of both field experiments and model simulations. Maximum brush removal resulted in a reduction in ET equal to 31.94 mm/yr depth over the entire basin, or 46.62 mm/yr depth over the treated area. Removal of heavy brush cover resulted in the greatest changes in evapotranspiration, surface runoff, base‐flow, and deep recharge. Slope was found to have the greatest effect on lateral subsurface flow.     

GIS‐Based Predictive Models of Hillslope Runoff Generation Processes1

Abstract: Successful nonpoint source pollution control using best management practice placement is a complex process that requires in‐depth knowledge of the locations of runoff source areas in a watershed. Currently, very few simulation tools are capable of identifying critical runoff source areas on hillslopes and those available are not directly applicable under all runoff conditions. In this paper, a comparison of two geographic information system (GIS)‐based approaches: a topographic index model and a likelihood indicator model is presented, in predicting likely locations of saturation excess and infiltration excess runoff source areas in a hillslope of the Savoy Experimental Watershed located in northwest Arkansas. Based on intensive data collected from a two‐year field study, the spatial distributions of hydrologic variables were processed using GIS software to develop the models. The likelihood indicator model was used to produce probability surfaces that indicated the likelihood of location of both saturation and infiltration excess runoff mechanisms on the hillslope. Overall accuracies of the likelihood indicator model predictions varied between 81 and 87% for the infiltration excess and saturation excess runoff locations respectively. On the basis of accuracy of prediction, the likelihood indicator models were found to be superior (accuracy 81‐87%) to the predications made by the topographic index model (accuracy 69.5%). By combining statistics with GIS, runoff source areas on a hillslope can be identified by incorporating easily determined hydrologic measurements (such as bulk density, porosity, slope, depth to bed rock, depth to water table) and could serve as a watershed management tool for identifying critical runoff source areas in locations where the topographic index or other similar methods do not provide reliable results.     

Applications of Explicitly Incorporated/Post‐Processing Measurement Uncertainty in Watershed Modeling

In the field of watershed modeling, the impact of measurement uncertainty (MU) on calibration results indicates the potential issue of inaccurate model predictions. It is important to note that MU refers to the uncertainty in measured data such as flow and nutrient values that are used to evaluate model outputs. The calculation of error statistics assuming measured data are deterministic may not be appropriate as has been frequently stated in literature. Although MU can affect model calibration results, it is rarely incorporated in modeling practice. MU can be incorporated in two schemes: explicitly incorporated (MU‐EI) during model calibration and post‐processed (MU‐PP) after calibration is completed. In this study, both schemes are implemented in a case study of the Arroyo Colorado Watershed, Texas. Unexpectedly, no substantial differences were observed between each scheme for flow predictions. Although MU did not cause dramatic differences in most sediment and NH₄‐N predictions, error statistics were affected in cases with MU greater than 50%, especially for sediment and NH₄‐N. Therefore, it is concluded that MU may not exert a significant impact on model predictions until certain threshold is reached. This study demonstrates that high levels of uncertainty in measured calibration/validation data significantly affect parameter estimation, especially in the auto‐calibration process.     

ADEQUACY OF SELECTED EVAPOTRANSPIRATION APPROXIMATIONS FOR HYDROLOGIC SIMULATION1

ABSTRACT: Evapotranspiration (ET) approximations, usually based on computed potential ET (PET) and diverse PET‐to‐ET conceptualizations, are routinely used in hydrologic analyses. This study presents an approach to incorporate measured (actual) ET data, increasingly available using micrometeorological methods, to define the adequacy of ET approximations for hydrologic simulation. The approach is demonstrated at a site where eddy correlation‐measured ET values were available. A baseline hydrologic model incorporating measured ET values was used to evaluate the sensitivity of simulated water levels, subsurface recharge, and surface runoff to error in four ET approximations. An annually invariant pattern of mean monthly vegetation coefficients was shown to be most effective, despite the substantial year‐to‐year variation in measured vegetation coefficients. The temporal variability of available water (precipitation minus ET) at the humid, subtropical site was largely controlled by the relatively high temporal variability of precipitation, benefiting the effectiveness of coarse ET approximations, a result that is likely to prevail at other humid sites.     

EVAPOTRANSPIRATION AND SOIL MOISTURE DYNAMICS ON A SEMIARID PONDEROSA PINE HILLSLOPE1

ABSTRACT: Detailed measurements of soil moisture and ET in semiarid forest environments have not been widely reported in the literature. In this study, soil moisture and water balance components were measured over a four‐year period on a semiarid ponderosa pine hillslope, with evapotranspiration (ET) determined as the residual of measured precipitation, runoff, and change in soil moisture storage. ET accounts for approximately 95 percent of the water budget and has a distinctly bimodal annual pattern, with peaks occurring after spring snowmelt and during the late summer monsoon season, periods that coincide with high soil moisture. Weekly growing season ET rates determined by the hillslope water balance are found to be invariably below calculated potential rates. Normalized ET rates are linearly correlated (r²= 0.62) with soil moisture; therefore, a simple linear relation is proposed. Growing season soil moisture dynamics were modeled based on this relation. Results are in fair agreement (r²= 0.63) with the observed soil moisture data over the four growing seasons; however, for two dry summers with little surface runoff, much better results (r² > 0.90) were obtained.     

HYDROLOGIC SIMULATION OF THE LITTLE WASHITA RIVER EXPERIMENTAL WATERSHED USING SWAT1

ABSTRACT: Precipitation and streamflow data from three nested subwatersheds within the Little Washita River Experimental Watershed (LWREW) in southwestern Oklahoma were used to evaluate the capabilities of the Soil and Water Assessment Tool (SWAT) to predict streamflow under varying climatic conditions. Eight years of precipitation and streamflow data were used to calibrate parameters in the model, and 15 years of data were used for model validation. SWAT was calibrated on the smallest and largest sub‐watersheds for a wetter than average period of record. The model was then validated on a third subwatershed for a range in climatic conditions that included dry, average, and wet periods. Calibration of the model involved a multistep approach. A preliminary calibration was conducted to estimate model parameters so that measured versus simulated yearly and monthly runoff were in agreement for the respective calibration periods. Model parameters were then fine tuned based on a visual inspection of daily hydrographs and flow frequency curves. Calibration on a daily basis resulted in higher baseflows and lower peak runoff rates than were obtained in the preliminary calibration. Test results show that once the model was calibrated for wet climatic conditions, it did a good job in predicting streamflow responses over wet, average, and dry climatic conditions selected for model validation. Monthly coefficients of efficiencies were 0.65, 0.86, and 0.45 for the dry, average, and wet validation periods, respectively. Results of this investigation indicate that once calibrated, SWAT is capable of providing adequate simulations for hydrologic investigations related to the impact of climate variations on water resources of the LWREW.     

Operational Evapotranspiration Mapping Using Remote Sensing and Weather Datasets: A New Parameterization for the SSEB Approach

The increasing availability of multi‐scale remotely sensed data and global weather datasets is allowing the estimation of evapotranspiration (ET) at multiple scales. We present a simple but robust method that uses remotely sensed thermal data and model‐assimilated weather fields to produce ET for the contiguous United States (CONUS) at monthly and seasonal time scales. The method is based on the Simplified Surface Energy Balance (SSEB) model, which is now parameterized for operational applications, renamed as SSEBop. The innovative aspect of the SSEBop is that it uses predefined boundary conditions that are unique to each pixel for the “hot” and “cold” reference conditions. The SSEBop model was used for computing ET for 12 years (2000‐2011) using the MODIS and Global Data Assimilation System (GDAS) data streams. SSEBop ET results compared reasonably well with monthly eddy covariance ET data explaining 64% of the observed variability across diverse ecosystems in the CONUS during 2005. Twelve annual ET anomalies (2000‐2011) depicted the spatial extent and severity of the commonly known drought years in the CONUS. More research is required to improve the representation of the predefined boundary conditions in complex terrain at small spatial scales. SSEBop model was found to be a promising approach to conduct water use studies in the CONUS, with a similar opportunity in other parts of the world. The approach can also be applied with other thermal sensors such as Landsat.     

Estimation of Evapotranspiration Across the Conterminous United States Using a Regression With Climate and Land‐Cover Data1

Sanford, Ward E. and David L. Selnick, 2012. Estimation of Evapotranspiration Across the Conterminous United States Using a Regression with Climate and Land‐Cover Data. Journal of the American Water Resources Association (JAWRA) 1‐14. DOI: 10.1111/jawr.12010 Abstract: Evapotranspiration (ET) is an important quantity for water resource managers to know because it often represents the largest sink for precipitation (P) arriving at the land surface. In order to estimate actual ET across the conterminous United States (U.S.) in this study, a water‐balance method was combined with a climate and land‐cover regression equation. Precipitation and streamflow records were compiled for 838 watersheds for 1971‐2000 across the U.S. to obtain long‐term estimates of actual ET. A regression equation was developed that related the ratio ET/P to climate and land‐cover variables within those watersheds. Precipitation and temperatures were used from the PRISM climate dataset, and land‐cover data were used from the USGS National Land Cover Dataset. Results indicate that ET can be predicted relatively well at a watershed or county scale with readily available climate variables alone, and that land‐cover data can also improve those predictions. Using the climate and land‐cover data at an 800‐m scale and then averaging to the county scale, maps were produced showing estimates of ET and ET/P for the entire conterminous U.S. Using the regression equation, such maps could also be made for more detailed state coverages, or for other areas of the world where climate and land‐cover data are plentiful.     

Instream Bacteria Influences from Bird Habitation of Bridges

The representativeness of ambient water samples collected from bridge crossings has occasionally been challenged because critics contend birds nesting on bridges elevate fecal indicator bacteria concentrations over samples collected from river reaches not spanned by bridges. This study was designed to evaluate the influence, if any, of bridge‐dwelling bird colonies on instream bacteria concentrations. Three bridges in central Texas were sampled under dry‐weather conditions for instream Escherichia coli. Two bridges were inhabited by migratory cliff swallows and one was devoid of birds. Numerous samples were collected from locations upstream, at the upstream bridgeface, and downstream of each bridge to determine whether significant increases in E. coli occurred in a downstream direction when birds were present. E. coli values increased significantly at bridgeface and downstream locations compared to upstream locations throughout the nesting season. During peak bird activity in May, bacteria geometric mean concentrations at bridgeface and downstream locations jumped from background levels <50 to >190 colony forming units (CFU)/100 mL, well above the state geometric mean criterion of 126 CFU/100 mL for primary contact recreation use. Results confirmed that under dry‐weather conditions bird colonies can have a significant impact on bacteria concentrations in the vicinity of the bridges they inhabit and therefore, to avoid this impact, monitoring should occur upstream of bridges.     

Water‐Yield Reduction After Afforestation and Related Processes in the Semiarid Liupan Mountains,Northwest China1

Abstract: The increase of coverage of forest/vegetation is imperative to improve the environment in dry‐land areas of China, especially for protecting soil against serious erosion and sandstorms. However, inherent severe water shortages, drought stresses, and increasing water use competition greatly restrict the reforestation. Notably, the water‐yield reduction after afforestation generates intense debate about the correct approach to afforestation and forest management in dry‐land areas. However, most studies on water‐yield reduction of forests have been at catchment scales, and there are few studies of the response of total evapotranspiration (ET) and its partitioning to vegetation structure change. This motivates us to learn the linkage between hydrological processes and vegetation structure in slope ecosystems. Therefore, an ecohydrological study was carried out by measuring the individual items of water balance on sloping plots covered by different vegetation types in the semiarid Liupan Mountains of northwest China. The ratio of precipitation consumed as ET was about 60% for grassland, 93% for shrubs, and >95% for forestland. Thus, the water yield was very low, site‐specific, and sensitive to vegetation change. Conversion of grassland to forest decreased the annual water yield from slope by 50‐100 mm. In certain periods, the plantations at lower slopes even consumed the runon from upper slopes. Reducing the density of forests and shrubs by thinning was not an efficient approach to minimize water use. Leaf area index was a better indicator than plant density to relate ET to vegetation structure and to evaluate the soil water carrying capacity for vegetation (i.e., the maximum amount of vegetation that can be supported by the available soil water for an extended time). Selecting proper vegetation types and plant species, based on site soil water condition, may be more effective than the forest density regulation to minimize water‐yield reduction by vegetation coverage increase and notably by reforestation. Finally, the focuses in future research to improve the forest‐water relations in dry‐land areas are recommended as follows: vegetation growth dynamics driven by environment especially water conditions, coupling of ecological and hydrological processes, further development of distributed ecohydrological models, quantitative relation of eco‐water quota of ecosystems with vegetation structures, multi‐scaled evaluation of soil water carrying capacity for vegetation, and the development of widely applicable decision support tools.     

Estimating Evapotranspiration for Dryland Cropping Systems in the Semiarid Texas High Plains Using SWAT

The Soil and Water Assessment Tool (SWAT) is one of the most widely used watershed models for simulating hydrology in response to agricultural management practices. However, limited studies have been performed to evaluate the SWAT model's ability to estimate daily and monthly evapotranspiration (ET) in semiarid regions. ET values were simulated using ArcSWAT 2012 for a lysimeter field managed under dryland conditions at the USDA‐ARS Conservation and Production Research Laboratory at Bushland, Texas, and compared with measured lysimeter values from 2000 to 2010. Two scenarios were performed to compare SWAT's performance: (1) use of default plant leaf area index (LAI) values in the embedded plant database and (2) adjusted LAI values. Scenario 1 resulted in an “unsatisfactory” Nash‐Sutcliffe efficiency (NSE) of 0.42 and 0.38 for the calibration and validation periods, respectively. Scenario 2 resulted in a “satisfactory” NSE value for the calibration period while achieving a “good” NSE of 0.70 for the validation period. SWAT generally underestimated ET at both the daily and monthly levels. Overestimation during fallow years may be due to the limitations of the pothole function used to simulate furrow diking. Users should be aware of potential errors associated with using default LAI parameters. Inaccuracies in ET estimation may also stem from errors in the plant stress functions, particularly when evaluating water management practices for dryland watersheds.     

VALIDATION OF THE SWAT MODEL ON A LARGE RWER BASIN WITH POINT AND NONPOINT SOURCES1

ABSTRACT: The State of Texas has initiated the development of a Total Maximum Daily Load program in the Bosque River Watershed, where point and nonpoint sources of pollution are a concern. Soil Water Assessment Tool (SWAT) was validated for flow, sediment, and nutrients in the watershed to evaluate alternative management scenarios and estimate their effects in controlling pollution. This paper discusses the calibration and validation at two locations, Hico and Valley Mills, along the North Bosque River. Calibration for flow was performed from 1960 through 1998. Sediment and nutrient calibration was done from 1993 through 1997 at Hico and from 1996 through 1997 at Valley Mills. Model validation was performed for 1998. Time series plots and statistical measures were used to verify model predictions. Predicted values generally matched well with the observed values during calibration and validation (R²≥ 0.6 and Nash‐Suttcliffe Efficiency ≥ 0.5, in most instances) except for some underprediction of nitrogen during calibration at both locations and sediment and organic nutrients during validation at Valley Mills. This study showed that SWAT was able to predict flow, sediment, and nutrients successfully and can be used to study the effects of alternative management scenarios.