Effects of nitrogen and phosphorus limitation on the activated sludge biomass in a kraft mill biotreatment system.

Unlike wastewater, pulp and paper mill effluents are generally severely deficient in bioavailable nitrogen and phosphorus. The influence of nitrogen and phosphorus limitations on steady-state or typical pulp and paper mill activated sludge floc properties and performance was studied using a bioreactor-fed synthetic raw mill effluent and seeded with mill activated sludge. Limitation of either nitrogen or phosphorus decreased growth, five-day biochemical oxygen demand, and suspended solids removal. Nitrogen limitation greatly enhanced activated sludge floc poly-beta3-hydroxybutyrate (PHB), but not carbohydrate or extracellular polymeric substances (EPS). In contrast, phosphorus limitation increased total floc carbohydrate and EPS, but not PHB. The flocs showed little ability to store either nitrogen or phosphorus. Nitrogen limitation, but not phosphorus limitation, produced much more negative net floc surface charge, increasing fines, while phosphorus limitation, but not nitrogen limitation, increased the floc bound water content and surface hydrophobicity and decreased fines.     

磺胺和四环素类抗生素对活性污泥性能的影响简

废水处理工艺中抗生素类污染物的存在可能会对生物处理过程产生长期而深远的影响,为探明此类污染物对废水生物处理主体活性污泥性能等方面的影响,采用间歇培养法研究了活性污泥法处理污水时,抗生素类污染物的存在对活性污泥性能如胞外聚合物（EPS）、污染物处理能力、脱氢酶活性和群落结构的影响。结果表明,抗生素的存在会导致活性污泥的胞外聚合物总量及其主要组分蛋白质和多糖增加,以产生保护屏障;且由于污泥絮体解体,细胞破裂导致EPS中DNA和色氨酸含量增加。同时,由于蛋白质大量增加引起的表面负电荷的增加,使污泥疏水性增强,絮凝性能恶化;污泥絮体解体导致污泥颗粒变小,SVI也随之下降;在活性污泥脱氢酶活性急剧下降的同时,出水TOC迅速升高。此外,抗生素类污染物在抑制活性污泥中大部分细菌的同时,对部分菌群也有刺激生长作用,最终导致活性污泥生物群落结构的改变。四环素类抗生素对活性污泥的EPS和絮凝沉降性能的影响大于磺胺类,而对污水处理能力和群落结构的影响则不如磺胺类。抗生素类污染物的长期存在会对活性污泥沉降性能、絮凝性能、脱氢酶活性以及活性污泥群落结构等产生一系列负面影响,进而影响污染物去除效果,导致出水水质恶化。     

Influences of influent carbon source on extracellular polymeric substances (EPS) and physicochemical properties of activated sludge

It is necessary to understand the bioflocculation, settling and dewatering characteristics in the activated sludge process in order to establish more efficient operational strategies. The influences of carbon source on the extracellular polymeric substances (EPS) and flocculation, settling and dewatering properties of the activated sludge were investigated. Laboratory-scale completely mixed activated sludge processes were used to grow the activated sludge with different carbon sources of starch, glucose and sodium acetate. The sludge fed with acetate had highest loosely bound EPS (LB-EPS) and that fed with starch lowest. The amount of tightly bound EPS (TB-EPS), protein content in LB-EPS, polysaccharide content and protein contents in TB-EPS, were independent of the influent carbon source. The polysaccharide content in LB-EPS of the activated sludge fed with sodium acetate was lower slightly than those of starch and glucose. The sludge also had a nearly consistent flocs size and the sludge volume index (SVI) value. ESS content of the sludge fed with sodium acetate was higher initially, although it was similar to those fed with glucose and starch finally. However, the specific resistance to filtration and normalized capillary suction time fluctuated first, but finally were stable at around 5.0 × 10⁸ m kg⁻¹ and 3.5 s L g⁻¹ SS, respectively. Only the protein content in LB-EPS weakly correlated with the flocs size and SVI of the activated sludge. But there was no correlation between any other EPS contents or components and the physicochemical properties of the activated sludge.     

Combined use of molecular biology taxonomy, Raman spectrometry, and ESEM imaging to study natural biofilms grown on filter materials at waterworks

DNA-based population analysis was applied in combination with Raman spectrometry and Environmental Scanning Electron Microscopy for the characterisation of natural biofilms from sand and activated carbon filters operated for a long term at a municipal waterworks. Whereas the molecular biology polymerase chain reaction combined with denaturing gradient gel electrophoresis approach provides a deeper insight into the bacterial biofilm diversities, Raman spectrometry analyses the chemical composition of the extracellular polymer substances (EPS), microorganisms embedded in EPS as well as other substances inside biofilm (inorganic compounds and humic substances). Microscopy images the spatial distribution of biofilms on the two different filter materials. In addition, bacterial bulk water populations were compared with biofilm consortia using the molecular fingerprint technique mentioned.Population analysis demonstrated the presence of more diverse bacterial species embedded in a matrix of EPS (polysaccharides, peptides, and nucleic acids) on the sand filter materials. In contrast to this, activated carbon granules were colonised by reduced numbers of bacterial species in biofilms. Besides α-, β-, and γ-Proteobacteria, a noticeable specific colonisation with Actinobacteria was found on activated carbon particles. Here, the reduced biofilm formation came along with a decreased EPS synthesis. The taxonomy profiles of the different biofilms revealed up to 60% similarity on the same filter materials and 32% similarity of different materials. Similarity of adherent communities from filter materials and bulk water populations from the filter effluent varied between 36% and 58% in sand filters and 6–40% in granular activated carbon filters.The biofilm investigation protocols are most crucial to subsequent acquisition of knowledge on biofilm dynamics and bacterial contributions to transformation or adsorption processes in waterworks facilities.     

胞外多聚物对活性污泥絮凝性能影响的研究进展

活性污泥的絮凝性能直接影响出水SS浓度,而胞外多聚物(EPS)是影响活性污泥絮凝性能的重要因素。从EPS的组分及其化学性质入手,结合现有的活性污泥絮凝机制评价了EPS在活性污泥絮凝性能中的重要作用,系统分析了EPS组分对污泥絮凝性能的影响,以及EPS产量和组分的影响因素,并就近年来的研究热点———松散层EPS、致密层EPS与活性污泥絮凝性能的关系进行了归纳,还对利用EPS提高活性污泥絮凝性能的技术应用进行了总结。最后,对该领域的研究方向进行了展望。     

Behaviour of bacterial extracellular polymeric substances from activated sludge: a review

Extracellular Polymeric Substances (EPS) are the predominant constituents of activated sludge and dramatically affect its properties. As EPS constitute as much as 50–90% of the solid phase of sludge, the use of EPS may bring a great reduction in sludge volume and mass, which have been great environmental interest. In this paper, results of over 60 publications related to structure, composition, storing condition, extraction and characteristics of EPS and their influences on behaviours of EPS is analysed. Possible application of EPS in heavy metal contamination is also discussed, together with a brief consideration of possible research interests.     

磺胺和四环素类抗生素对活性污泥性能的影响

废水处理工艺中抗生素类污染物的存在可能会对生物处理过程产生长期而深远的影响,为探明此类污染物对废水生物处理主体活性污泥性能等方面的影响,采用间歇培养法研究了活性污泥法处理污水时,抗生素类污染物的存在对活性污泥性能如胞外聚合物（EPS）、污染物处理能力、脱氢酶活性和群落结构的影响。结果表明,抗生素的存在会导致活性污泥的胞外聚合物总量及其主要组分蛋白质和多糖增加,以产生保护屏障;且由于污泥絮体解体,细胞破裂导致EPS中DNA和色氨酸含量增加。同时,由于蛋白质大量增加引起的表面负电荷的增加,使污泥疏水性增强,絮凝性能恶化;污泥絮体解体导致污泥颗粒变小,SVI也随之下降;在活性污泥脱氢酶活性急剧下降的同时,出水TOC迅速升高。此外,抗生素类污染物在抑制活性污泥中大部分细菌的同时,对部分菌群也有刺激生长作用,最终导致活性污泥生物群落结构的改变。四环素类抗生素对活性污泥的EPS和絮凝沉降性能的影响大于磺胺类,而对污水处理能力和群落结构的影响则不如磺胺类。抗生素类污染物的长期存在会对活性污泥沉降性能、絮凝性能、脱氢酶活性以及活性污泥群落结构等产生一系列负面影响,进而影响污染物去除效果,导致出水水质恶化。     

活性污泥胞外聚合物提取方法优化

试验对比了不同离子交换树脂(CER)含量和pH条件下胞外聚合物(EPS)的提取效果差异。结果表明,EPS各组分提取浓度均随离子交换树脂用量增加而增加,但各组分趋势不同。TOC的最佳树脂剂量为100 g CER/g VSS,而蛋白质、多糖和DNA的最佳树脂剂量约为70 g CER/g VSS。pH值对TOC、DNA和多糖的提取浓度影响较小,但对蛋白质影响比较大。各提取条件下,EPS各组分提取浓度随时间的变化过程可以分为平稳增长期、快速增长期及稳定期。     

Specific resistance to filtration of biomass from membrane bioreactor reactor and activated sludge: effects of exocellular polymeric substances and dispersed microorganisms.

This study investigates the effect of dispersed microorganisms and exocellular polymeric substances on biomass dewaterability. Specific resistance to filtration (SRF) was measured for biomass from a membrane bioreactor and a completely mixed activated sludge system. Both laboratory-scale reactors were fed with synthetic wastewater and operated at a high food-to-microorganism ratio (F/M) (1 to 11 kilograms chemical oxygen demand per kilogram mixed liquor volatile suspended solids per day [kgCOD/(kg MLVSS.d)]) and short solids retention times (0.25 to 5 d). The SRF values were affected by strong interactions of three parameters: (1) the mixed liquor suspended solids concentration, (2) the amount of dispersed microorganisms, and (3) the exocellular polymeric substances (EPS) concentration. At F/M smaller than 2 kg COD/(kg MLSS.d) and mixed liquor suspended solids (MLSS) concentration higher than 2000 mg/L, increasing amount of dispersed microorganisms in the biomass yielded higher SRF values. However, at high F/M (> 5 kg COD/kg MLSS.d) and low MLSS concentrations (< 600 mg/L), lower EPS concentrations resulted in slightly smaller SRF values, even though the amount of dispersed microorganisms in the biomass was much higher. Thus, at low MLSS concentrations, EPS concentrations rather than the amount of dispersed microorganisms tend to control SRF.     

Solubilization of municipal sewage waste activated sludge by novel lytic bacterial strains

Extracellular polymeric substances (EPS) are an extracellular matrix found in sludge which plays a crucial role in flocculation by interacting with the organic solids. Therefore, to enhance pretreatment of sludge, EPS have to be removed. In this study, EPS were removed with a chemical extractant, NaOH, to enhance the bacterial pretreatment. A lysozyme secreting bacterial consortium was isolated from the waste activated sludge (WAS). The result of density gradient gel electrophoresis (DGGE) analysis revealed that the isolated consortium consists of two strains. The two novel strains isolated were named as Jerish03 (NCBI accession number KC597266) and Jerish 04 (NCBI accession number KC597267) and they belong to the genus Bacillus. Pretreatment with these novel strains enhances the efficiency of the aerobic digestion of sludge. Sludge treated with the lysozyme secreting bacterial consortium produced 29 % and 28.5 % increase in suspended solids (SS) reduction and chemical oxygen demand (COD) removal compared to the raw activated sludge (without pretreatment) during aerobic digestion. It is specified that these two novel strains had a high potential to enhance WAS degradation efficiency in aerobic digestion.     

Study on substrate metabolism process of saline waste sludge and its biological hydrogen production potential

With the increasing of high saline waste sludge production, the treatment and utilization of saline waste sludge attracted more and more attention. In this study, the biological hydrogen production from saline waste sludge after heating pretreatment was studied. The substrate metabolism process at different salinity condition was analyzed by the changes of soluble chemical oxygen demand (SCOD), carbohydrate and protein in extracellular polymeric substances (EPS), and dissolved organic matters (DOM). The excitation-emission matrix (EEM) with fluorescence regional integration (FRI) was also used to investigate the effect of salinity on EPS and DOM composition during hydrogen fermentation. The highest hydrogen yield of 23.6 mL H₂/g VSS and hydrogen content of 77.6% were obtained at 0.0% salinity condition. The salinity could influence the hydrogen production and substrate metabolism of waste sludge.

     

Investigation of triclosan fate and toxicity in continuous-flow activated sludge systems

The purpose of this research was to study the fate and toxicity of triclosan (TCS) in activated sludge systems and to investigate the role of biodegradation and sorption on its removal. Two continuous-flow activated sludge systems were used; one system was used as a control, while the other received TCS concentrations equal to 0.5 and 2mgl(-1). At the end of the experiment, 1mgl(-1) TCS was added in the control system to investigate TCS behaviour and effects on non-acclimatized biomass. For all concentrations tested, more than 90% of the added TCS was removed during the activated sludge process. Determination of TCS in the dissolved and particulate phase and calculation of its mass flux revealed that TCS was mainly biodegraded. Activated sludge ability to biodegrade TCS depended on biomass acclimatization and resulted in a mean biodegradation of 97%. Experiments with batch and continuous-flow systems revealed that TCS is rapidly sorbed on the suspended solids and afterwards, direct biodegradation of sorbed TCS is performed. Regarding TCS effects on activated sludge process, addition of 0.5mgl(-1) TCS on non-acclimatized biomass initially deteriorated ammonia removal and nitrification capacity. After acclimatization of biomass, nitrification was fully recovered and further increase of TCS to 2mgl(-1) did not affect the performance of activated sludge system. The effect of TCS on organic substrate removal was minor for concentrations up to 2mgl(-1), indicating that heterotrophic microorganisms are less sensitive to TCS than nitrifiers.     

Investigation of Cr(VI) reduction in continuous-flow activated sludge systems

The aim of this research was to investigate hexavalent chromium, Cr(VI), reduction by activated sludge and to evaluate the use of continuous-flow activated sludge systems for the treatment of Cr(VI)-containing wastewater. Three series of experiments were conducted using two parallel lab-scale activated sludge systems. During the first experiment, one system was used as a control, while the other received Cr(VI) concentrations equal to 0.5, 1, 3 and 5mg l(-1). For all concentrations added, approximately 40% of the added Cr(VI) was removed during the activated sludge process. Determination of chromium species in the dissolved and particulate phase revealed that the removed Cr(VI) was sorbed by the activated sludge flocs mainly as trivalent chromium, Cr(III), while the residual chromium in the dissolved phase was mainly detected as Cr(VI). Activated sludge ability to reduce Cr(VI) was independent of the acclimatization of biomass to Cr(VI) and it was not affected by the toxic effect of Cr(VI) on autotrophic and heterotrophic microorganisms. During the second experiment, both systems were operated under two different hydraulic residence time (theta equal to 20 and 28h) and three different initial organic substrate concentration (COD equal to 300, 150 and 0mg l(-1)). Cr(VI) reduction was favored by an increase of theta, while it was limited by influent COD concentration. Finally, at the last experiment the effect of anoxic and anaerobic reactors on Cr(VI) reduction was investigated. It was observed that the use of an anoxic zone or an anaerobic-anoxic zone ahead of the aerobic reactor favored Cr(VI) reduction, increasing mean percentage Cr(VI) reduction to almost 80%.     

Comparison of the complexation potential of extracellular polymeric substances (EPS), extracted from activated sludges and produced by pure bacteria strains, for cadmium, lead and nickel

This paper provides information on the metal complexation potential of extracellular polymeric substances (EPS), extracted from activated sludges and from eight pure cultures of bacteria isolated from the same activated sludge. The EPS extracted from pure bacteria cultures are mainly composed of proteins and low quantities of polysaccharides and uronic acids in comparison with EPS extracted from activated sludges. The EPS studied present two apparent pK(a) and the IR spectra show the presence of the same functional groups on all the EPS studied. The ability of EPS to complex Cd, Pb and Ni, was studied at pH 7 with Chau and Ruzic's models using polarography titration. All of the EPS exhibited a greater ability to complex Pb than Ni, Cd showing the weakest affinity overall. The EPS extracted from the pure cultures of bacteria were less able to complex the metals than that extracted from activated sludges. Literature data, IR data and EPS phosphorous content, supported by the EPS pK(a), revealed that carboxylic and phosphoric groups may play a major role in binding to metals at pH 7. This study underlines the importance of metal exposure in order for bacteria to secrete or modify EPS. After exposure, the EPS then exhibit the greatest capacity to bind metal in order to protect bacteria from harmful effects of heavy metals.     

Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, part II: multilayer biofilm diffusional model

Research was undertaken to develop a diffusional model of the biofilm that can be applied in lieu of a semi-empirical model to upgrade an activated sludge system to an integrated fixed-film activated sludge (IFAS) or moving-bed biofilm reactor (MBBR) system. The model has been developed to operate with up to 12 cells (reactors) in series, with biofilm media incorporated to one or more of the zone cells, except the anaerobic zone cells. The values of the kinetic parameters for the model were measured using pilot-scale activated sludge, IFAS, and MBBR systems. The biofilm is divided into 12 layers and has a stagnant liquid layer. Diffusion and substrate utilization are calculated for each layer. The equations are solved simultaneously using a finite difference technique. The biofilm flux model is then linked to the activated sludge model. Advanced features include the ability to compute the biofilm thickness and the effect of biofilm thickness on performance. The biofilm diffusional model is also used to provide information and create a table of biofilm yields at different substrate concentrations that can be used in the semi-empirical model.     

Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, part III: analysis and verification

Research was undertaken to analyze and verify a model that can be applied to activated sludge, integrated fixed-film activated sludge (IFAS), and moving-bed biofilm reactor (MBBR) systems. The model embeds a biofilm model into a multicell activated sludge model. The advantage of such a model is that it eliminates the need to run separate computations for a plant being retrofitted from activated sludge to IFAS or MBBR. The biofilm flux rates for organics, nutrients, and biomass can be computed by two methods-a semi-empirical model of the biofilm that is relatively simpler, or a diffusional model of the biofilm that is computationally intensive. Biofilm support media can be incorporated to the anoxic and aerobic cells, but not the anaerobic cells. The model can be run for steady-state and dynamic simulations. The model was able to predict the changes in nitrification and denitrification at both pilot- and full-scale facilities. The semi-empirical and diffusional models of the biofilm were both used to evaluate the biofilm flux rates for media at different locations. The biofilm diffusional model was used to compute the biofilm thickness and growth, substrate concentrations, volatile suspended solids (VSS) concentration, and fraction of nitrifiers in each layer inside the biofilm. Following calibration, both models provided similar effluent results for reactor mixed liquor VSS and mixed liquor suspended solids and for the effluent organics, nitrogen forms, and phosphorus concentrations. While the semi-empirical model was quicker to run, the diffusional model provided additional information on biofilm thickness, quantity of growth in the biofilm, and substrate profiles inside the biofilm.     

Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, Part I: Semi-empirical model development

Research was undertaken to develop a model for activated sludge, integrated fixed-film activated sludge (IFAS), and moving-bed biofilm reactor (MBBR) systems. The model can operate with up to 12 cells (reactors) in series, with biofilm media incorporated to one or more cells, except the anaerobic cells. The process configuration can be any combination of anaerobic, anoxic, aerobic, post-anoxic with or without supplemental carbon, and reaeration; it can also include any combination of step feed and recycles, including recycles for mixed liquor, return activated sludge, nitrates, and membrane bioreactors. This paper presents the structure of the model. The model embeds a biofilm model into a multicell activated sludge model. The biofilm flux rates for organics, nutrients, and biomass can be computed by two methods--a semi-empirical model of the biofilm that is relatively simpler, or a diffusional model that is computationally intensive. The values of the kinetic parameters for the model were measured using pilot-scale activated sludge, IFAS, and MBBR systems. For the semiempirical version, a series of Monod equations were developed for chemical oxygen demand, ammonium-nitrogen, and oxidized-nitrogen fluxes to the biofilm. Within the equations, a second Monod expression is used to simulate the effect of changes in biofilm thickness and fraction nitrifiers in the biofilm. The biofilm flux model is then linked to the activated sludge model. The diffusional model and the verification of the models are presented in subsequent papers (Sen and Randall, 2008a, 2008b). The model can be used to quantify the amount of media and surface area required to achieve nitrification, identify the best locations for the media, and optimize the dissolved oxygen levels and nitrate recycle rates. Some of the advanced features include the ability to apply different media types and fill fractions in cells; quantify nitrification, denitrification, and biomass production in the biofilm and mixed liquor suspended solids; and perform dynamic simulations.     

Enhanced biological phosphorus removal and recovery

Activated sludge systems designed for enhanced nutrient removal are based on the principle of altering anaerobic and aerobic conditions for growth of microorganisms with a high capacity of phosphorus accumulation. Most often, filamentous bacteria constitute a component of the activated sludge microflora. The filamentous microorganisms are responsible for foam formation and activated sludge bulking. The results obtained confirm unanimously that the filamentous bacteria have the ability of phosphorus uptake and accumulation as polyphosphates. Hydrodynamic disintegration of the foam microorganisms results in the transfer of phosphorus and metal cations and ammonium-nitrogen into the liquid phase. It was demonstrated that the disintegration of foam permits the removal of a portion of the nutrients in the form of struvite.     

Applications of the deep-shaft activated sludge process in wastewater treatment

The deep-shaft activated sludge process is a unique modification of the activated sludge system. The main objective of this system is to increase the amount of dissolved oxygen available for biological activity. This can be achieved by increasing the rate of oxygen transfer from the gas phase to the liquid phase. The deep-shaft configuration increases the partial pressure of oxygen, thereby causing a high saturation concentration in the reactor. In the deep-shaft process, owing to high oxygen availability, a higher organic loading can be accommodated with a comparatively low air supply. This reduces the energy and area requirements and lowers the overall cost of treatment. This technology has been successfully applied for the high-rate treatment of strongly polluted wastewater, as well as for the treatment of wastewater containing toxic or slowly biodegradable pollutants. This paper presents different applications of the deep-shaft activated sludge process, along with their relative performances.     

Effect of multiwalled carbon nanotubes on UASB microbial consortium

The continuous rise in production and applications of carbon nanotubes (CNTs) has grown a concern about their fate and toxicity in the environment. After use, these nanomaterials pass through sewage and accumulate in wastewater treatment plants. Since, such plants rely on biological degradation of wastes; their activity may decrease due to the presence of CNTs. This study investigated the effect of multiwalled carbon nanotubes (MWCNTs) on upflow anaerobic sludge blanket (UASB) microbial activity. The toxic effect on microbial viability, extracellular polymeric substances (EPS), volatile fatty acids (VFA), and biogas generation was determined. The reduction in a colony-forming unit (CFU) was 29 and 58 % in 1 and 100 mg/L test samples, respectively, as compared to control. The volatile fatty acids and biogas production was also found reduced. The scanning electron microscopy (SEM) and fluorescent microscopy images confirmed that the MWCNT mediated microbial cell damage. This damage caused the increase in EPS carbohydrate, protein, and DNA concentration. Fourier transform infrared (FTIR) spectroscopy results supported the alterations in sludge EPS due to MWCNT. Our observations offer a new insight to understand the nanotoxic effect of MWCNTs on UASB microflora in a complex environment system.