Experimentally-derived upper thermal tolerances for redhorse suckers: revised 316(A) variance conditions at two generating facilities in Ohio

American Electric Power’s Conseville Station and Muskingum River Plant, located on the Muskingum River in southeastern Ohio, utilize once-through cooling for seven (combined) generating units. Both facilities had approved 316(a) variances that required maintenance of a baseline fully-mixed downstream temperature of 31.6°C (88.9°F). Fish sampling conducted during critical conditions in Summer 1993 indicated the presence of thermally-sensitive redhorse suckers (Moxostoma sp.) at river temperatures >32.2°C (90.0°F). Because the assumed upper tolerance limit for redhorse suckers (31.6°C) was extrapolated from field observations, we determined the actual thermal tolerance of suckers using fish collected locally. During September 1996 golden and shorthead redhorses were collected from the nearby Walhonding River. The short-term upper thermal tolerances were determined by the ultimate upper incipient lethal temperature (UUILT) and the critical thermal maximum (CTM) endpoints. For shorthead redhorse the calculated UUILT was 33.3°C (91.9°F), and the CTM was 35.1°C (95.2°F). For golden redhorse a similar CTM was obtained; however, a reliable UUILT could not be extrapolated due to procedural problems. The results of these tests played a role in Ohio EPA approving a higher fully-mixed downstream limit. This study demonstrates the value of obtaining thermal tolerances experimentally when assumed tolerance values are considered suspect.     

Hot spots in the bee hive

Honeybee colonies (Apis mellifera) maintain temperatures of 35-36°C in their brood nest because the brood needs high and constant temperature conditions for optimal development. We show that incubation of the brood at the level of individual honeybees is done by worker bees performing a particular and not yet specified behaviour: such bees raise the brood temperature by pressing their warm thoraces firmly onto caps under which the pupae develop. The bees stay motionless in a characteristic posture and have significantly higher thoracic temperatures than bees not assuming this posture in the brood area. The surface of the brood caps against which warm bees had pressed their thorax were up to 3.2°C warmer than the surrounding area, confirming that effective thermal transfer had taken place.     

Potential climate change impacts on Atlantic cod (Gadus morhua) off the northeastern USA

We examined the potential impacts of future climate change on the distribution and production of Atlantic cod (Gadus morhua) on the northeastern USA’s continental shelf. We began by examining the response of cod to bottom water temperature changes observed over the past four decades using fishery-independent resource survey data. After accounting for the overall decline in cod during this period, we show that the probability of catching cod at specified locations decreased markedly with increasing bottom temperature. Our analysis of future changes in water temperature was based on output from three coupled atmosphere–ocean general circulation models under high and low CO₂ emissions. An increase of <1.5°C is predicted for all sectors under the low emission scenario in spring and autumn by the end of this century. Under the high emission scenario, temperature increases range from ～2°C in the north to >3.5°C in the Mid-Atlantic Bight. Under these conditions, cod appear vulnerable to a loss of thermal habitat on Georges Bank, with a substantial loss of thermal habitat farther south. We also examined temperature effects on cod recruitment and growth in one stock area, the Gulf of Maine, to explore potential implications for yield and resilience to fishing. Cod survival during the early life stages declined with increasing water temperatures, offsetting potential increases in growth with warmer temperatures and resulting in a predicted loss in yield and increased vulnerability to high fishing mortality rates. Substantial differential impacts under the low versus high emission scenarios are evident for cod off the northeastern USA.     

Mercury release behaviors of Guizhou bituminous coal during co-pyrolysis: Influence of chlorella

Co-pyrolysis of coal and seaweed can not only effectively decrease the carbon footprint but also improve the quality and output of coal pyrolysis products, however, the influence of seaweed on thermal releasing behaviors of mercury during co-pyrolysis process are still unclear. In this work, the chlorella and Guizhou bituminous coal were mixed and used to reveal the mercury release behavior during co-pyrolysis by the temperature programmed pyrolysis experiments, thermogravimetric and differential thermogravimetric analysis (TG-DTG) and thermogravimetry-mass spectrometry (TG-MS) methods, offering a sufficient explanation on the control technology of mercury pollutants in co-pyrolysis. The results exhibited that a large amount of reducing gases such as CO, H₂ and H₂O were generated in chlorella at the temperature range of 100-500°C, which was favorable for the transformation from oxidized mercury to elemental mercury, thus remarkably increased the release of elemental mercury in the raw coal sample. The mixed chlorella also significantly lowered the decomposition temperature range (from 400-600 to 300-400°C) of pyrite-bound mercury and decreased the decomposition temperatures of the pyrite-bound mercury species. Additionally, in the co-pyrolysis about 91.82% of mercury was released into the gas phase below 400°C and was 13.77% higher than that of in individual pyrolysis of coal.     

The response of a mid- and high latitude peat bog to predicted climate change: methane production in a 12-month peat incubation

There are fears that global warming will lead to degradation of peatlands, higher emissions of greenhouse gases from peat, and accelerated warming. Anaerobic decomposition of organic soils produces methane (CH₄), a potent greenhouse gas. Two peat bogs differing in mean annual temperature, Velke Darko (VD, Czech Republic, 7.2 °C), and Stor Åmyran (SA, Sweden, 4.0 °C), were selected for a comparative study of how organic soils in different climatic zones will respond to warmer and drier conditions. Twenty peat cores from each bog were incubated in growth chambers. Under present-day summer conditions, VD produced 14 times more CH₄ than SA. Two different warming scenarios were used. Peat-core replicates were kept at temperatures of 11 versus 16 °C, and 11 versus 22 °C. From 11 to 16 °C, the CH₄ production slightly decreased at SA, and slightly increased at VD. From 11 to 22 °C, the CH₄ production increased 9 times at SA, but slightly decreased at VD. After an 8-month incubation, peat cores under drying conditions (water table at ?14 cm) were compared to samples with original water table (?2 cm). Drying conditions led to a steeper reduction in CH₄ production at VD, compared to SA. The CH₄ production decreased more than 100 times at VD. Then, the combined effect of simultaneous warming and drying at 11 and 22 °C was studied. We did not find any significant effect of interactions between increasing temperature and decreasing water table level. Overall, the warmer site VD responded more strongly to the simulated climate change than the colder site SA.     

Impacts of climate variability and changes on domestic water use in the Yellow River Basin of China

We present a methodology for using a domestic water use time series that were obtained from Yellow River Conservancy Commission, together with the climatic records from the National Climate Center of China to evaluate the effects of climate variability on water use in the Yellow River Basin. A suit of seven Global Circulation Models (GCMs) were adopted to anticipate future climate patterns in the Yellow River. The historical records showed evidences of rises in temperature and subsequent rises in domestic water demand in the basin. For Upstream of Longyangxia region, the impact was the least, with only 0.0021?×?10⁸ m³ for a temperature increase of 1 °C; while for Longyangxia-Lanzhou region, domestic water use was found to increase to 0.18?×?10⁸ m³ when temperature increases 1 °C. Downstream of Huayuankou was the region with the most changes in temperature that gave the highest increase of 1.95?×?10⁸ m³ in domestic water demand for 1 °C of change of temperature. Downstream of Huayuankou was identified as the most vulnerable area, where domestic water demand increases nearly by 42.2 % with 1 °C increase of temperature. Judging from the trends of temperature range, we concluded that future temperature in Yellow River Basin has an increasing tendency. This could worsen the existing issues of domestic water demand and even more to trigger high competition among different water-using sectors.     

Adaptation strategies to combat climate change effect on rice and mustard in Eastern India

The negative impact of climate change on crop production is alarming as the demand for food is expected to increase in coming years, at a rate of about 2 percent a year. Wet season rice (Oryza sativa) followed by mustard (Brassica juncea) is one of the prominent cropping sequences in Eastern India. Descreases in their productivity due to climate change will not only hamper the regional food security but also affect the global economy. Considering the fact, the present study aims to assess the impact of climate change on productivity of wet-season rice and mustard and to evaluate the effectiveness of agronomic adjustment as adaptation options. Crop growth simulation model (CGSM) is a very effective tool to predict the growth and yield of a crop. One CGSM, namely InfoCrop (Generic Crop Model), was calibrated and validated for the said crops for West Bengal State, Eastern India. After validation, the model was used to predict the yield under elevated thermal condition (1 and 3 °C rise over normal temperature). Moreover, the future weather situation as predicted by PRECIS (Providing Regional Climates for Impacts Studies) model was used as weather input of the CGSM and the yield was predicted for ten selected locations of West Bengal for the year 2025 and 2050. It was observed that the average yield reduction of the wet-season rice would be in the tune of about 20.0 % for 2025 and 27.8 % for 2050. The mustard yield of West Bengal may be reduced by 20.0 to 33.9 % for the year 2025 and up to 40 % for 2050. It was concluded that the negative impact of climate change on mustard grown in winter season will be more pronounced compared to wet-season rice. Adjustment of sowing time will be the simplest and effective adaptation option for both rice and mustard. Increased rate of nutrient application can sustain the rice yield under future climate. The older seedling at the time of transplanting of wet-season rice and increased seed rate of mustard were proved less effective.     

城市户外热环境的舒适性研究

介绍了户外热环境舒适性评价的几种方法，提出了户外热环境舒适评价指标OTCD，指出了在室内OTCD能与PMV很好吻合，并且OTCD的各项参数便于测量。     

Is phenotypic plasticity a key mechanism for responding to thermal stress in ants?

Unlike natural selection, phenotypic plasticity allows organisms to respond quickly to changing environmental conditions. However, plasticity may not always be adaptive. In insects, body size and other morphological measurements have been shown to decrease as temperature increases. This relationship may lead to a physiological conflict in ants, where larger body size and longer legs often confer better thermal resistance. Here, we tested the effect of developmental temperature (20, 24, 28 or 32 °C) on adult thermal resistance in the thermophilic ant species Aphaenogaster senilis. We found that no larval development occurred at 20 °C. However, at higher temperatures, developmental speed increased as expected and smaller adults were produced. In thermal resistance tests, we found that ants reared at 28 and 32 °C had half-lethal temperatures that were 2 °C higher than those of ants reared at 24 °C. Thus, although ants reared at higher temperatures were smaller in size, they were nonetheless more thermoresistant. These results show that A. senilis can exploit phenotypic plasticity to quickly adjust its thermal resistance to local conditions and that this process is independent of morphological adaptations. This mechanism may be particularly relevant given current rapid climate warming.     

Impact of climate change on regional irrigation water demand in Baojixia irrigation district of China

Water scarcity in China would possibly be aggravated by rapid increase in water demand for irrigation due to climate change. This paper focuses on the mechanism of climate change impact on regional irrigation water demand by considering the dynamic feedback relationships among climate change, irrigation water demand and adaptation measures. The model in implemented using system dynamics approach and employed in Baojixia irrigation district located in Shaanxi Province of China to analyses the changes in irrigation water demand under different climate change scenarios. Obtained results revealed that temperature will be the dominant factor to determine irrigation water demand in the area. An increase of temperature by 1 °C will result in net irrigation water demand to increase by about 12,050?×?10⁴ m³ and gross water demand by about 20,080?×?10⁴ m³ in the area. However, irrigation water demand will not increase at the same rate of temperature rise as the adaptation measures will eventually reduce the water demand increased by temperature rise. It is expected that the modeling approach presented in this study can be used in adopting policy responses to reduce climate change impacts on water resources.     

A global analysis of residential heating and cooling service demand and cost-effective energy consumption under different climate change scenarios up to 2050

Climate change and energy service demand exert influence on each other through temperature change and greenhouse gas emissions. We have consistently evaluated global residential thermal demand and energy consumption up to the year 2050 under different climate change scenarios. We first constructed energy service demand intensity (energy service demand per household) functions for each of three services (space heating, space cooling, and water heating). The space heating and cooling demand in 2050 in the world as a whole become 2.1–2.3 and 3.8–4.5 times higher than the figures for 2010, whose ranges are originated from different global warming scenarios. Cost-effective residential energy consumption to satisfy service demand until 2050 was analyzed keeping consistency among different socio-economic conditions, ambient temperature, and carbon dioxide (CO₂) emission pathways using a global energy assessment model. Building shell improvement and fuel fuel-type transition reduce global final energy consumption for residential thermal heating by 30% in 2050 for a 2 °C target scenario. This study demonstrates that climate change affects residential space heating and cooling demand by regions, and their desirable strategies for cost-effective energy consumption depend on the global perspectives on CO₂ emission reduction. Building shell improvement and energy efficiency improvement and fuel fuel-type transition of end-use technologies are considered to be robust measures for residential thermal demand under uncertain future CO₂ emission pathways.     

Hot bats: extreme thermal tolerance in a desert heat wave

Climate change is predicted to increase temperature extremes and thus thermal stress on organisms. Animals living in hot deserts are already exposed to high ambient temperatures (T _a) making them especially vulnerable to further warming. However, little is known about the effect of extreme heat events on small desert mammals, especially tree-roosting microbats that are not strongly protected from environmental temperature fluctuations. During a heat wave with record T _as at Sturt National Park, we quantified the thermal physiology and behaviour of a single free-ranging little broad-nosed (Scotorepens greyii, henceforth Scotorepens) and two inland freetail bats (Mormopterus species 3, henceforth Mormopterus) using temperature telemetry over 3 days. On 11 and 13 January, maximum T _a was ～45.0 °C, and all monitored bats were thermoconforming. On 12 January 2013, when T _a exceeded 48.0 °C, Scotorepens abandoned its poorly insulated roost during the daytime, whereas both Mormopterus remained in their better insulated roosts and were mostly thermoconforming. Maximum skin temperatures (T _skin) ranged from 44.0 to 44.3 °C in Scotorepens and from 40.0 to 45.8 °C in Mormopterus, and these are the highest T _skin values reported for any free-ranging bat. Our study provides the first evidence of extensive heat tolerance in free-ranging desert microbats. It shows that these bats can tolerate the most extreme T _skin range known for mammals (3.3 to 45.8 °C) and delay regulation of T _skin by thermoconforming over a wide temperature range and thus decrease the risks of dehydration and consequently death.     

回转窑热解气化炉处理生活垃圾特性

基于目前固定床热解气化法在常温下进行存在燃气热值和气化效率较低、燃料适用范围小和预处理复杂等问题,采用控制变量法设计探究了不同预热空气温度和过量空气系数对小型回转窑式热解气化炉处理村镇生活垃圾的影响.结果表明:预热空气温度升高有利于垃圾热解气化产气,但有一定的局限性,当温度超过600 ℃时垃圾的气化产气明显下降;当过量空气系数为0.4时,垃圾的热解气化效率达到最大值,并且焦油产量最小.垃圾原样在过量空气系数为0.4、空气预热温度为500 ℃下对底渣、飞灰进行重金属含量的分析测试结果显示,飞灰中的铅含量远高于GB 18598—2001《危险废物填埋污染控制标准》相关标准限值,需要经过处理才能排放,二英采样分析结果显示其含量均低于GB 18485—2014《生活垃圾焚烧污染控制标准》限值.研究显示,该回转窑式热解气化工艺处理生活垃圾的最佳过量空气系数为0.4,最佳空气预热温度为500 ℃,在此最佳工况条件下焦油产量小,飞灰及焦渣中重金属含量小,ρ(二英)低于0.10 ng/m3.      

Evaluation of ecological design strategies in traditional houses in Diyarbakir,Turkey

This study focuses on the ecological design between traditional Diyarbak?r houses and their physical environment (topography and climate) and structural environment (building form, spatial organization, material, landscape and planting, and technical infrastructure). The basic principle was to identify the criteria that would use natural energy sources and provide the most benefit to the inhabitants. The influence of different seasons on thermal perception was investigated. The average temperature differences between the outdoor and indoor environment of the houses were 7 °C in winter, 6 °C in summer and ±2 °C in spring and autumn. Consequently, this paper discusses ecological design solutions used in traditional houses and their applicability to modern buildings and recognizes that architecture should coexist and maintain harmony with nature.     

Telomeric attrition with age and temperature in Eastern mosquitofish (Gambusia holbrooki)

Telomeric attrition has repeatedly been found to correlate with the ageing of organisms; however, recent research is increasingly showing that the determinants of attrition dynamics are not well understood. This study examined the relative telomere lengths in Eastern mosquitofish, Gambusia holbrooki, kept at different temperatures and at different ages. Newly born fry were randomly selected for one of four treatment groups: 20, 30, 20–30, and 30–20 °C, where the third and fourth treatment groups were gradually changed from their starting temperature to their final temperature between days 10 and 14. Telomere length was measured, and it was found that length decreased with age and that fish exposed to the 20 °C treatment had significantly shorter telomeres than those that received the 30–20 °C treatment. Telomeric attrition with age agrees with results previously found in studies of telomeres; however, the variation in attrition with temperature was not simply predictable and may be the synergistic effects of temperature and some other factor.     

The Effect of Heat on the Physicochemical Properties of Bacteriophage MS2

The differences in physicochemical characteristics between infectious and non-infectious viral particles are poorly known. Even for heat, which is known as one of the most efficient treatments to inactivate enteric viruses, the global inactivation mechanisms have not been described yet. Such knowledge would help distinguish between both types of particles and therefore clarify the interpretation of the presence of viral genomes in food after heat treatment. In this study, we examined in particular the differences in electrostatic charge and hydrophobicity between the two particle types. MS2 phage, a common surrogate for enteric viruses, was used as a model virus. The heat-induced inactivation process of the infectious phages caused hydrophobic domains to be transiently exposed and their charge to become less negative. The particles also became progressively permeable to small molecules such as SYPRO Orange dye. The presence of non-infectious phage particles in which the genome was not accessible to RNases has been clearly demonstrated. These observations were done for MS2 phages exposed to a temperature of 60 °C. When exposed to a temperature higher than their critical temperature (72 °C), the particles were disrupted and the genome became available for RNases. At lower temperatures, 60 °C in this study, the transient expression of hydrophobic domains of remaining infectious phages appeared as an interesting parameter for improving their specific detection.     

Temperature and parasitism by <Emphasis Type="BoldItalic">Asobara tabida</Emphasis> (Hymenoptera: Braconidae) influence larval pupation behaviour in two <Emphasis Type="BoldItalic">Drosophila</Emphasis> species

In holometabolous insects, pupation site selection behaviour has large consequences for survival. Here, we investigated the combined effects of temperature and parasitism by the parasitoid Asobara tabida on larval pupation behaviour in two of its main Drosophila sp. hosts differing in their climate origin. We found that larvae of Drosophila melanogaster—a species with a (sub)tropical origin—placed at 25°C pupated higher in rearing jars than those placed at 15°C. The opposite pattern was observed for Drosophila subobscura larvae—a species from temperate regions—which pupated lower, i.e. on or near the substrate at 25°C, than those placed at 15°C. When placed at 25°C, parasitized larvae of both species pupated closer to the substrate than unparasitized ones. Moreover, the Drosophila larvae that had been exposed and probably stung by A. tabida, but were not parasitized, pupated lower than the control unparasitized larvae. These results provide new insights of host behaviour manipulation by A. tabida larvae.     

空间站应用系统电子设备热设计研究

目的针对以往载人航天应用系统中电子设备热设计的仿真分析方法不准确的问题,提出一种基于热平衡试验测量发热元器件温度数据验证热仿真分析结果的电子设备热设计方法。方法通过对应用系统电子设备在轨实际热工况条件的深入分析,结合电子设备的物理特性、电气特性及其技术特点,利用计算机应用技术和数字仿真技术建立电子设备热模型,并进行热仿真分析,再将仿真计算得到的发热元器件壳温与实际热平衡试验测量得到的元器件真实壳温比对,检验热仿真分析结果的准确性。结果某电子设备在真空度为1.0×10~(-4) Pa,温度为45℃条件下开展热平衡试验,实测得到的发热元器件温度值与热仿真分析温度值之差小于1℃。热平衡试验过程中,切换电子设备的不同工作模式时,通过器件的工作电流和电压计算出其热负荷指标与仿真得到的热耗值之差低于0.1 W。结论基于热平衡试验的发热元器件实测温度数据,验证了热仿真分析结果的电子设备热设计方法科学有效,有助于后续空间站应用系统电子设备热设计工作。     

Thermal Gains Through Collective Metabolic Heat Production in Social Caterpillars of Eriogaster lanestris

 We investigated thermal characteristics of aggregations of social, tent-building caterpillars of the small eggar moth Eriogaster lanestris (Lepidoptera: Lasiocampidae). The highly synchronous behavior of individuals of the colony has important consequences for their thermal ecology. Air temperature in the tent fluctuates according to the caterpillars' activity: air temperature slowly rises about 2.5–3  °C above the surroundings when caterpillars aggregate in the tent after feeding and decreases rapidly when the larvae leave the tent. Thermal energy can be stored for a few hours when ambient temperature drops. Experiments show that metabolic heat production sufficiently explains this effect. As even minor additional heat gain may reduce developmental time, aggregating in the tent may thus confer selective advantages under overcast weather or at night, when behavioral thermoregulation through basking is not possible. Received: 24 November 1999 / Accepted in revised form: 26 January 2000     

On wear resistance of tool steel

Maintaining a reasonably low cutting tool wear when producing forming tools is a general challenge in the development of new forming tool materials. The tool life of a hot forming tool steel (H13) has been significantly improved by reducing its Si-content from 1.0 to 0.06 wt.%. However, this modified H13 (MH13) also displays a reduced cutting tool life due to higher cutting forces and a stronger tendency to form built up layers (BUE) on the cutting edge. This paper explains why.Gleeble tests of MH13 revealed a significantly higher flow stress in the 820–900 °C temperature interval in MH13 compared to H13. Thermo-Calc simulations showed that when reducing the Si-content from 1.0 to 0.06 wt.% the initial temperature for ferrite-to-austenite transformation (A1) was reduced from 900 °C to 820 °C. Knowing that austenite has totally different mechanical and thermal properties than ferrite, the difference in A1 between the two steels explains the higher cutting forces and higher tendency for BUE-formation. The conclusion is that the difference in machinability between H13 and MH13 is primarily related to their difference in A1.An attempt was also made to find a new tool material composition that can combine the wear resistance of MH13 and the good machinability of H13. Thermo-Calc simulations were performed with slightly modified alloying content without changing its properties as a good forming tool material, with the aim to increase A1. For instance, reducing the Mn content from 0.5 to 0.05 wt.% proved to increase A1 from 820 to 850 °C.