Application of a chemically modified green macro alga as a biosorbent for phenol removal

Phenol and substituted phenols are toxic organic pollutants present in tannery waste streams. Environmental legislation defines the maximum discharge limit to be 5–50 ppm of total phenols in sewers. Thus the efforts to develop new efficient methods to remove phenolic compounds from wastewater are of primary concern. The present work aims at the use of a modified green macro alga (Caulerpa scalpelliformis) as a biosorbent for the removal of phenolic compounds from the post-tanning sectional stream. The effects of initial phenol concentration, contact time, temperature and initial pH of the solution on the biosorption potential of macro algal biomass have been investigated. Biosorption of phenol by modified green macro algae is best described by the Langmuir adsorption isotherm model. Biosorption kinetics of phenol onto modified green macro algal biomass were best described by a pseudo second order model. The maximum uptake capacity was found to be 20 mg of phenol per gram of green macro algae. A Boyd plot confirmed the external mass transfer as the slowest step involved in the biosorption process. The average effective diffusion coefficient was found to be 1.44 × 10⁻⁹ cm²/s. Thermodynamic studies confirmed the biosorption process to be exothermic.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Utilization of powdered waste sludge (PWS) for removal of textile dyestuffs from wastewater by adsorption

Acid pre-treated powdered waste sludge (PWS) was used for removal of textile dyestuffs from aqueous medium by adsorption as an alternative to the use of powdered activated carbon (PAC). The rate and extent of dysetuff removals were determined for four different dyestuffs at different PWS concentrations varying between 1 and 6 gl(-1). Biosorbed dyestuff concentrations at equilibrium decreased with increasing PWS concentration for all dyestuffs tested. PWS was more effective for adsorption of Remazol red RR and Chrisofonia direct yellow 12 as compared to the other dyestuffs tested. More than 80% percent dyestuff removal was obtained for all dyestuffs at PWS concentrations above 4 gl(-1) after 6h of incubation. Similar to percent dyestuff removal, the rate of adsorption was maximum at a PWS concentration of 4 gl(-1). Kinetics of adsorption of dyestuffs was investigated by using the first- and second-order kinetic models and the kinetic constants were determined. Second-order kinetics was found to fit the experimental data better than the first-order model for all dyestuffs tested. Adsorption isotherms were established for all dyestuffs used and the isotherm constants were determined by using the experimental data. Langmuir and the generalized adsorption isotherms were found to be more suitable than the Freundlich isotherm for correlation of equilibrium adsorption data. Acid pre-treated PWS was proven to be an effective adsorbent for dyestuff removal as compared to the other adsorbents reported in literature studies.     

Kinetic and equilibrium isotherm studies for the adsorptive removal of Brilliant Green dye from aqueous solution by rice husk ash

The present study deals with the adsorption of Brilliant Green (BG) on rice husk ash (RHA). RHA is a solid waste obtained from the particulate collection equipment attached to the flue gas lines of rice husk fired boilers. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH0), contact time, adsorbent dose and initial concentration (C0) on the removal of BG. Optimum conditions for BG removal were found to be pH0 approximately 3.0, adsorbent dose approximately 6 g L(-1) of solution and equilibrium time approximately 5 h for the C0 range of 50-300 mg L(-1). Adsorption of BG followed pseudo-second-order kinetics. Intra-particle diffusion does not seem to control the BG removal process. Equilibrium isotherms for the adsorption of BG on RHA were analyzed by Freundlich, Langmuir, Redlich-Peterson (R-P), Dubnin-Radushkevich (D-R), and Temkin isotherm models using a non-linear regression technique. Langmuir and R-P isotherms were found to best represent the data for BG adsorption onto RHA. Adsorption of BG on RHA is favourably influenced by an increase in the temperature of the operation. Values of the change in entropy (DeltaS0) and heat of adsorption (DeltaH0) for BG adsorption on RHA were positive. The high negative value of change in Gibbs free energy (DeltaG0) indicates the feasible and spontaneous adsorption of BG on RHA.     

Experimental investigation of adsorption capacity of anthill in the removal of heavy metals from aqueous solution

In the present work, the adsorption capacity of anthill was investigated as a low‐cost adsorbent to remove the heavy metal ions, lead (II) ion (Pb²⁺), and zinc (II) ion (Zn²⁺) from an aqueous solution. The equilibrium adsorption isotherms of the heavy metal ions were investigated under batch process. For the study we examined the effect of the solution's pH and the initial cations concentrations on the adsorption process under a fixed contact time and temperature. The anthill sample was characterized using a scanning electron microscope (SEM), X‐ray fluorescence (XRF), and Fourier transform infrared (FTIR) techniques. From the SEM analysis, structural change in the adsorbent was a result of heavy metals adsorption. Based on the XRF analysis, the main composition of the anthill sample was silica (SiO₂), alumina (Al₂O₃), and zirconia (ZrO₂). The change in the peaks of the spectra before and after adsorption indicated that there was active participation of surface functional groups during the adsorption process. The experimental data obtained were analyzed using 2‐ and 3‐parameter isotherm models. The isotherm data fitted very well to the 3‐parameter Radke–Prausnitz model. It was noted that Pb²⁺ and Zn²⁺ can be effectively removed from aqueous solution using anthill as an adsorbent.     

Removal of Se(IV) from aqueous solution using sulphuric acid-treated peanut shell

A carbonaceous sorbent was prepared from peanut shell via sulphuric acid treatment. Se(IV) removal from aqueous solution on the sorbent was studied varying time, pH, Se(IV) concentration, temperature and sorbent status (wet and dry). Se(IV) removal was faster using the wet sorbent than the dry sorbent following a pseudo-first-order model. Se(IV) removal increases at low pH values, and decreases as pH increases until pH 7. Sorption was found to fit the Langmuir equation and sorption capacity for the wet sorbent was higher than that for the dry one. Both sorbents showed an increased selenium sorption by rising the temperature. Redox processes between Se(IV) and the carbon sorbent are involved. Analysis by scanning electron microscope and X-ray powder diffraction for the sorbent after the reaction with acidified Se(IV) confirmed the availability of elemental selenium as particles on the sorbent surface as a result of Se(IV) reduction. Physicochemical tests showed an increase in sorbent acidity, cation exchange capacity (CEC) and surface functionality after the reaction with acidified Se(IV), indicating the oxidation processes occurring on the sorbent surface. Due to its reduction properties, the sorbent seems efficient for Se(IV) removal from aqueous solution.     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

Use of agricultural waste for the removal of nitrate-nitrogen from aqueous medium

The effectiveness of wheat straw charcoal (WSC) and mustard straw charcoal (MSC) as adsorbents for the removal of nitrate-nitrogen from water has been investigated. Commercial activated carbon (CAC) was used as a standard for comparison. The adsorption effectiveness of MSC was highest followed by CAC and WSC irrespective of the concentration of nitrate-nitrogen in the range of 0-25mg/l. The effects of temperature in the range of 15-28 degrees C on adsorption by WSC and MSC have also been investigated. It was observed that the temperature dependence of the adsorption effectiveness of MSC was higher than that of WSC and CAC. It is concluded that the MSC can be used for the in situ treatment by adsorption of nitrate-nitrogen in underground and surface water.     

Application of carbon adsorbents prepared from Brazilian-pine fruit shell for the removal of reactive orange 16 from aqueous solution: Kinetic,equilibrium, and thermodynamic studies

Activated (AC-PW) and non-activated (C-PW) carbonaceous materials were prepared from the Brazilian-pine fruit shell (Araucaria angustifolia) and tested as adsorbents for the removal of reactive orange 16 dye (RO-16) from aqueous effluents. The effects of shaking time, adsorbent dosage and pH on the adsorption capacity were studied. RO-16 uptake was favorable at pH values ranging from 2.0 to 3.0 and from 2.0 to 7.0 for C-PW and AC-PW, respectively. The contact time required to obtain the equilibrium using C-PW and AC-PW as adsorbents was 5 and 4 h at 298 K, respectively. The fractionary-order kinetic model provided the best fit to experimental data compared with other models. Equilibrium data were better fit to the Sips isotherm model using C-PW and AC-PW as adsorbents. The enthalpy and entropy of adsorption of RO-16 were obtained from adsorption experiments ranging from 298 to 323 K.     

Comparison of biosorbents with inorganic sorbents for removing copper(II) from aqueous solutions

In comparison with several other reported inorganic sorbents, Camellia tree leaf and primary sludge obtained from a settling tank as a pretreatment to the activated sludge system in a Hong Kong sewage treatment plant were evaluated for removing Cu(II) from aqueous solutions. Experimental data were modeled by the Langmuir isotherm equation to estimate the maximum sorption capacity (q_max). Results show that, at pH 5.6, biosorbents, Camellia tree leaf and primary sludge in particular, exert higher sorption capacities (q_max > 40 mg g⁻¹) than inorganic sorbents, Na-montmorillonite (q_max = 33.3 mg g⁻¹), fly ash (q_max = 18.8 mg g⁻¹), and goethite powder (10.3 mg g⁻¹). Furthermore, a pseudo second-order kinetic model was found to properly describe the experimental data for both bio- and inorganic sorbents. Sorption of Cu(II) on the Camellia tree leaf and primary sludge were much faster than that on the inorganic sorbents. In addition, desorption tests revealed that the desorption capacities of the two biomaterials are higher than the other selected materials; and much more Cu(II) can be retrieved from the Cu(II)-loaded biosorbents. Finally, increasing solution pH was found to greatly increase q_max and accelerate sorption processes.     

Effect of template in MCM-41 on the adsorption of aniline from aqueous solution

The effect of the surfactant template cetyltrimethylammonium bromide (CTAB) in MCM-41 on the adsorption of aniline was investigated. Various MCM-41 samples were prepared by controlling template removal using an extraction method. The samples were then used as adsorbents for the removal of aniline from aqueous solution. The results showed that the MCM-41 samples with the template partially removed (denoted as C-MCM-41) exhibited better adsorption performance than MCM-41 with the template completely removed (denoted as MCM-41). The reason for this difference may be that the C-MCM-41 samples had stronger hydrophobic properties and selectivity for aniline because of the presence of the template. The porosity and cationic sites generated by the template play an important role in the adsorption process. The optimal adsorbent with moderate template was achieved by changing the ratio of extractant; it has the potential for promising applications in the field of water pollution control.     

Use of an activated carbon from antibiotic waste for the removal of Hg(II) from aqueous solution

Porous carbon has been prepared from waste antibiotic material by a chemical activation method using K(2)CO(3) as an activating reagent. Carbon was studied systematically by the adsorption of nitrogen and iodine. It was found that the process parameters such as activation temperature and activation time are crucial for preparing high-quality activated carbon. The proper choice of the preparation conditions allows to produce microporous activated carbon with a micropore volume up to 0.492 cm(3)/g and a BET surface area of 1260 m(2)/g. Adsorption of mercury(II) from an aqueous solution on antibiotic carbon was investigated under the varying conditions of agitation time, metal ion concentration and pH. The adsorption capacity of the carbon is 129 mg/g.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.     

Evaluation of the gene expression changes in Nile tilapia (<Emphasis Type="Italic">Oreochromis niloticus</Emphasis>) as affected by the bio-removal of toxic textile dyes from aqueous solution in small-scale bioreactor

A laboratory-scale bioremediation unit was designed, built and tested for the bio-removal of several Direct textile dyes. Four experiments were carried out to assess the efficiency of the bioremediation unit using Aspergillus niger fungal strain. Three commonly used Direct dyes and textile dyes mixture (simulated effluent: Direct brown, Direct violet, Direct green) were tested in this study. The strain of A. niger was efficient in the removal of the three Direct dyes. The decolorization percentages of the dyes after 24 h of incubation were 56.2, 51.7, and 95.4% for Direct brown, Direct green, Direct violet dyes, respectively. The percentages increased up to 79.4, 86.4, and 96.7% after 72 h of incubation for the same dyes, respectively. The results also showed that the fungal strain reduced the chemical oxygen demand values of simulated dye effluents from 165 to 564 mg/l with most of the dyes. The assessment of bioremediation products on biomodel was conducted using a fresh water fish. The liver and brain of Nile tilapia were tested to evaluate the expression of genes coding for several proteins related to stress such as metallothioneins (MTs), cytochrome P450 (CYP450), and heat shock proteins (HSPs). To assess the alterations in the gene expression, ten animals from each group were killed after 4 weeks of treatment. The results revealed significant increases in the brain and hepatic mRNA levels of all stress protein genes MT, CYP450, Hsp70a, b, and Hsp47 in the fish groups treated with industrial Direct violet, green, and brown dye water. Exposure of tilapia to bioremediation products after treatment with A. niger fungi reduced the over-expression of the stress protein genes in the brain and liver tissues.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Optimizing process parameters for the adsorption of phosphorus from synthetic wastewater on coconut shell based activated carbon

Activated carbon was prepared from coconut shell, an agricultural waste, for the removal of phosphorus from synthetic phosphorus‐containing wastewater. The activated carbon obtained from the coconut shell was characterized using Fourier‐transform infrared (FTIR) spectroscopy. Batch mode experiments were conducted to study the effects of pH, particle size, adsorbent dosage, and sorption time on the adsorptive potential of the prepared activated carbon. Response surface methodology was employed to study the interactions among the variables and to optimize the process conditions for the maximum removal of phosphorus using the coconut shell–based activated carbon (CNS). The characterization results from the FTIR showed the presence of variety of functional groups, such as ?OH, ?NH, C=O, C?H, C?N, CH₃, and CH₂, which explains the CNS's improved adsorption behavior on the colloidal particles. A maximum performance of 95.22% was obtained for CNS at the optimum conditions of adsorbent dosage = 1,000 milligrams (local variable), pH 2 (local variable), particle size = 0.2 millimeters (local variable), and sorption time = 4.2 hours (global variable).