Optimization of nitrate reduction by EDTA catalyzed zero-valent bimetallic nanoparticles in aqueous medium

The present study aims to investigate the EDTA catalyzed reduction of nitrate (NO ₃ ^? ) by zero-valent bimetallic (Fe?CAg) nanoparticles (ZVBMNPs) in aqueous medium and to enumerate the effect of temperature, solution pH, ZVBMNPs dose and EDTA concentration on NO ₃ ^? reduction. Batch experimental data were generated using a four-factor Box?CBehnken design. Optimization modeling was performed using the response surface method for maximizing the reduction of NO ₃ ^? by ZVBMNPs. Significance of the independent variables and their interactions were tested by the analysis of variance and t test statistics. The model predicted maximum reduction capacity (340.15?mg?g^?1 NO ₃ ^? ) under the optimum conditions of temperature, 60?°C; pH?4; dose, 1.0?g?l^?1; and EDTA concentration, 2.0?mmol?l^?1 was very close to the experimental value (338.62?mg?g^?1) and about 16?% higher than the experimentally determined capacity (291.32?mg?g^?1). Study demonstrated that ZVBMNPs had higher reduction efficiency than Fe⁰ nanoparticles for NO ₃ ^? . EDTA significantly enhanced the NO ₃ ^? reduction by ZVBMNPs. The EDTA catalyzed reduction of NO ₃ ^? by ZVBMNPs can be employed for the effective decontamination of water.     

Application of central composite face-centered design and response surface methodology for the optimization of electro-Fenton decolorization of Azure B dye

Purpose

The aim of this work was to improve the ability of electro-Fenton technique for the remediation of wastewater contaminated with synthetic dyes using a model azo dye such as Azure B.

Methods

Batch experiments were conducted to study the effects of main parameters, such as dye concentration, electrode surface area, treatment time, and voltage. In this study, central composite face-centered experimental design matrix and response surface methodology were applied to design the experiments and evaluate the interactive effects of the four studied parameters. A total of 30 experimental runs were set, and the kinetic data were analyzed using first- and second-order models.

Results

The experimental data fitted to the empirical second-order model of a suitable degree for the maximum decolorization of Azure B by electro-Fenton treatment. ANOVA analysis showed high coefficient of determination value (R ²?=?0.9835) and reasonable second-order regression prediction. Pareto analysis suggests that the variables, time, and voltage produce the largest effect on the decolorization rate.

Conclusion

Optimum conditions suggested by the second-order polynomial regression model for attaining maximum decolorization were dye concentration 4.83?mg/L, electrode surface area 15?cm², voltage 14.19?V, and treatment time of 34.58?min.     

Aquatic photochemistry of paracetamol in the presence of dissolved organic chromophoric material and nitrate

Purpose

This study contains some new findings connected to the photolysis of the drug paracetamol (hereinafter APAP) especially in light of estimating natural conditions, and it will offer information to better evaluate environmental problems connected with this widely used analgesic agent. Only a few studies, so far, have focussed on the photodegradation process of APAP in the natural environment, and the question about the role of the colored/chromophoric dissolved organic matter (CDOM) and nitrate (NO ₃ ^? ) as photoinductors is almost open.

Methods

APAP dissolved in freshwater and pure laboratory water in the presence and absence of CDOM and NO ₃ ^? ions was irradiated using weak-energy photon energies simulating natural conditions.

Results

CDOM and NO ₃ ^? as photoinductors produced only the slow phototransformation of APAP under weak energy radiation, and APAP seemed to be practically resistant to direct photolysis under weak radiant energies available in natural conditions. The estimated reaction efficiencies, in addition to half-lives, speak for that NO ₃ ^? and CDOM do not act as quite independent photoinductors but their effect in conjunction (CDOM?CNO ₃ ^? ?Cwater) is stronger than the separate ones. The principal phototransformation intermediates of APAP were mono-hydroxy derivatives, depending on available photon energies formed via ortho- or meta-hydroxylation, possessing substantial power of resistance to further specific transformation reactions.

Conclusions

The estimated half-life of the phototransformation of APAP in the natural aqueous environment and in the presence of suitable photoinductors will be about 30?days or more.     

Changes in character of organics in the receiving environment of effluent from a sulphite pulp mill

Purpose

The characteristics of organics in sulphite pulp mill effluent and in the receiving environment of effluent discharge were investigated to assess the basis for the persistence or attenuation of colour.

Methods

Characterization of organics was conducted through determination of SUVA, specific colour, and molecular weight distribution of organics using high performance size exclusion chromatography and by solid-state ¹³?C cross polarization (CP) NMR. The characteristics of organics from mill wastewater before and after secondary aerobic treatment, followed by lime treatment and from the receiving environment, an enclosed brackish lake were compared. Changes in the character of organics in lake water over a period of 14?years were studied in the context of changes in mill processing and climate impacts.

Results

High colour in mill effluent and in receiving waters correlated with high SUVA and specific colour levels, high molecular weight range and aromatic content. Conversely, lake waters with low colour had UV absorbing compounds of much lower molecular weight range and low relative abundance of aromatic compounds. Attenuation of colour and changes in the character of organics in the receiving environment coincided with increased concentrations of metal cations.

Conclusions

These increased concentrations appear to be due to the effects of climate change, lake management and their presence in mill effluent, with subsequent discharge to the lake. Attenuation of colour was found to be predominantly through removal of high molecular weight aromatic compounds where the removal processes could be through adsorption and co-precipitation with divalent metals, as well as through dilution processes.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.     

Performance evaluation of a tailor-made passive sampler for monitoring of tropospheric ozone

Introduction

This study presents the performance evaluation of a tailor-made passive sampler developed for the monitoring of tropospheric ozone.

Methods

The performance of the passive sampler was tested in the field conditions in terms of accuracy, precision, blank values, detection limit, effects of some parameters such as sampling site characteristics and sampling period on the field blanks, self-consistency, experimental and theoretical uptake rates, shelf life and comparison with commercial passive samplers.

Results

There was an agreement (R ²?=?0.84) between the responses of passive sampler and the continuous automatic analyser. The accuracy of the sampler, expressed as percent relative error, was obtained lower than 15%. Method precision in terms of coefficient of variance for three simultaneously applied passive samplers was 12%. Sampler detection limit was 2.42???g?m^?3 for an exposure period of 1?week, and the sampler can be stored safely for a period of up to 8?weeks before exposure. Satisfactory self-consistency results showed that extended periods gave the same integrated response as a series of short-term samplers run side by side. The uptake rate of ozone was found to be 10.21?mL?min^?1 in a very good agreement with the theoretical uptake rate (10.32?mL?min^?1). The results of the comparison study conducted against a commercially available diffusion tube (Gradko diffusion tube) showed a good linear relationship (R ²?=?0.93) between two passive samplers.

Conclusions

The sampler seems suitable to be used in large-scale measurements of ozone where no data are available or the number of existing automated monitors is not sufficient.     

Evaluation of substrate removal kinetics for UASB reactors treating chlorinated ethanes

Purpose

Lack of focus on the treatment of wastewaters bearing potentially hazardous pollutants like 1,1,2 trichloroethane and 1,1,2,2 tetrachloroethane in anaerobic reactors has provided an impetus to undertake this study. The objective of this exercise was to quantify the behavior of upflow anaerobic sludge blanket reactors and predict their performance based on the overall organic substrate removal.

Methods

The reactors (wastewater-bearing TCA (R2), and wastewater-bearing TeCA (R3)) were operated at different hydraulic retention times (HRTs), i.e., 36, 30, 24, 18, and 12?h corresponding to food-to-mass ratios varying in the range of 0.2?C0.7?mg chemical oxygen demand (COD) mg^?1 volatile suspended solids day^?1. The process kinetics of substrate utilization was evaluated on the basis of experimental results, by applying three mathematical models namely first order, Grau second order, and Michaelis-Menten type kinetics.

Results

The results showed that the lowering of HRT below 24?h resulted in reduced COD removal efficiencies and higher effluent pollutant concentrations in the reactors. The Grau second-order model was successfully applied to obtain the substrate utilization kinetics with high value of R ² (>0.95). The Grau second-order substrate removal constant (K ₂) was calculated as 1.12 and 7.53?day^?1 for reactors R2 and R3, respectively.

Conclusion

This study demonstrated the suitability of Grau second-order kinetic model over other models, for predicting the performance of reactors R2 and R3, in treating wastewaters containing chlorinated ethanes under different organic and hydraulic loading conditions.     

Copper chitosan nanocomposite: synthesis, characterization, and application in removal of organophosphorous pesticide from agricultural runoff

Purpose

Removal of malathion from agricultural runoff was studied using novel copper-coated chitosan nanocomposite (CuCH)??a biopolymeric waste obtained from marine industry.

Methods

Synthesis and characterization of the adsorbent using different spectral techniques like Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer, Emmett, and Teller surface analyzer have been carried out. Equilibrium studies have been carried out to optimize the dose rate, pH, and the reaction time. Parathion and methyl parathion removal were also evaluated by CuCH in the batch mode. Using gas chromatography?Cmass spectrometry (GC?CMS) and FTIR studies suitable mechanism for adsorption has been suggested.

Results

The particle size of the adsorbent ranged from 700 to 750?nm. The surface area was found to be 20?m²?g^-1 with a pore volume of 0.11?cc?g^-1. The maximum adsorption capacity of malathion by CuCH was found to be 322.6?±?3.5?mg?g^-1 at an optimum pH of 2.0. Presence of copper ions enhanced the adsorption capacity of the adsorbent. The reaction was found to follow pseudo second-order kinetics with a rate constant of 0.53?g?mg^-1?min^-1. Evidence from FTIR indicated that copper ions form a dithionate complex with malathion during the adsorption stage. The adsorbent was found to remove malathion completely from spiked concentration of 2?mg?l^-1 in the agricultural run-off samples. It was also found that CuCH removed other organophospurous pesticides like methyl parathion and parathion under prevailing conditions.

Conclusions

The results indicated that CuCH could be applied for the removal of organophosphorous pesticides.     

Improvement of biodegradability of PVA-containing wastewater by ionizing radiation pretreatment

Background

Polyvinyl alcohol (PVA) has been widely used as sizing agents in textile and manufacturing industry, and it is a refractory compound with low biodegradability.

Objective

The objective of this paper was to treat the PVA-containing wastewater using gamma irradiation as a pretreatment strategy to improve its biodegradability and to determine the roles of different kinds of radical species played during pretreatment.

Methods

Gamma radiation was carried out in a ⁶⁰Cobalt source station, PVA concentration was analyzed by using a visible spectrophotometer and specific oxygen uptake rate (SOUR, milligram of O₂ per gram of mixed liquor volatile suspended solids (MLVSS) per hour) was measured by a microrespirometer.

Results

The results showed that the biodegradability of PVA-containing wastewater with low initial concentration (e.g., 327.8?mg/l) could be improved greatly with increasing irradiation dose. However, PVA gel formation was observed at higher initial PVA concentration (e.g., 3,341.6?mg/l) and higher irradiation dose, which inhibited PVA degradation by aerobic microorganisms. However, the formed gel could be separated by microfiltration, which led to more than 90% total organic carbon (TOC) removal.

Conclusion

Ionizing radiation could be used as a pretreatment technology for PVA-containing wastewater, and its combination with biological process is feasible.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.     

Degradation and mineralization of sulcotrione and mesotrione in aqueous medium by the electro-Fenton process: a kinetic study

Introduction

The degradation and mineralization of two triketone (TRK) herbicides, including sulcotrione and mesotrione, by the electro-Fenton process (electro-Fenton using Pt anode (EF-Pt), electro-Fenton with BDD anode (EF-BDD) and anodic oxidation with BDD anode) were investigated in acidic aqueous medium.

Methods

The reactivity of both herbicides toward hydroxyl radicals was found to depend on the electron-withdrawing effect of the aromatic chlorine or nitro substituents. The degradation of sulcotrione and mesotrione obeyed apparent first-order reaction kinetics, and their absolute rate constants with hydroxyl radicals at pH?3.0 were determined by the competitive kinetics method.

Results and discussion

The hydroxylation absolute rate constant (k _abs) values of both TRK herbicides ranged from 8.20?×?10⁸ (sulcotrione) to 1.01?×?10⁹ (mesotrione) L?mol^?1?s^?1, whereas those of the TRK main cyclic or aromatic by-products, namely cyclohexane 1,3-dione , (2-chloro-4-methylsulphonyl) benzoic acid and 4-(methylsulphonyl)-2-nitrobenzoic acid, comprised between 5.90?×?10⁸ and 3.29?×?10⁹?L?mol^?1?s^?1. The efficiency of mineralization of aqueous solutions of both TRK herbicides was evaluated in terms of total organic carbon removal. Mineralization yields of about 97?C98% were reached in optimal conditions for a 6-h electro-Fenton treatment time.

Conclusions

The mineralization process steps involved the oxidative opening of the aromatic or cyclic TRK by-products, leading to the formation of short-chain carboxylic acids, and, then, of carbon dioxide and inorganic ions.     

Concentration of organic micropollutants in the atmosphere of Trieste, Italy

Purpose

PCDD/Fs, PCBs, and PAHs, ubiquitous environmental pollutants which are part of the POPs, are mainly produced by anthropogenic activities as well as by natural processes. Occurrences of these pollutants in different sites in Trieste are presented. PCDD/Fs distribution and their possible emission sources are discussed.

Methods

Air samples were collected in different sites near the industrial area, in the city center, and in a background area, using a high-volume sampler equipped with a quartz fiber filter and a PUF. Each sampling lasted a week.

Results

The concentrations of the organochlorinated pollutants are consistent with literature data (??PCDD/Fs and ??dl-PCBs were 5?C38?fg TEQ/Nm³ and 4?C31?fg TEQ/Nm³, respectively), and an apparent seasonal trend was found with slightly higher concentrations in the winter and lower levels in both summer campaigns. Moreover, the isomer profile of each sampling campaign was compared to the fingerprint of a sintering plant, a cement plant, and an incinerator, the main industrial activities in Trieste.

Conclusions

The organic micropollutants were detected in levels consistent with literature data. The results show that the pollutants are uniformally distributed in the atmosphere of Trieste. PCDD/F fingerprints in each site remained almost identical during summer and winter, confirming the yearly prevalence of the emissions from the nearby sintering plant.     

Characteristics of precipitation chemistry at Lushan Mountain, East China: 1992–2009

Introduction

Trends in precipitation pH and conductivity during 1992?C2009, and in ionic compositions from January 2007 to June 2009, are reported from Lushan Mountain, one of the highest mountains in mid-east China. Annual mean pH was in the range of 4.35?C5.01 and showed a statistically very significant (P?P?Results and discussions Over the period of study, Lushan Mountain received more rainfall in spring and summer. The pH values varied seasonally with winter minima. The winter multiyear seasonal mean pH was 4.35. The corresponding summer value was 4.88. SO ₄ ^2? and NO ₃ ^? were the main anions, and NH ₄ ⁺ and Ca²⁺ the main cations. The anion to cation ratio was 0.8?C1.0, and that of [SO ₄ ^2? ] to [NO ₃ ^? ] was 2.4-3.0, much lower than that of the 1980s. However, sulfuric acid was still the main acid present. The ratio of [NH ₄ ⁺ ] to [Ca²⁺] was about 1.0, suggesting that these two alkaline substances provided close acid neutralizing capacity. The ratio of [Cl^?] to [Na⁺] was about 0.67, somewhat lower than that of natural precipitation.

Conclusions

Ionic composition varied seasonally and was closely correlated to the amounts of rainfall and pollution. Trajectory analyses showed that the trajectories to Lushan Mountain could be classified in six clusters and trajectories originating from the South Sea and the areas surrounding Lushan Mountain had the greatest impacts on precipitation chemistry.     

Cloud point extraction for the preconcentration of palladium and lead in environmental samples and determination by flow injection flame atomic absorption spectrometry

Purpose

An online cloud-point extraction (CPE) coupled with flow injection method is developed for the separation and preconcentration of palladium and lead from various matrices using flame atomic absorption spectrometry (FAAS).

Method

The method employs the formation of complexes of the metallic species with dimethylglyoxime, which are subsequently entrapped in the micelles of the surfactant Triton X-114, upon increase of the solution temperature to 60°C and loaded into the flow injection system at a flow rate of 4.6?mL?min^?1. The surfactant rich-phase was retained in a minicolumn packed with animal wool at pH?6 and eluted with 1.0?mol?L^?1 nitric acid in methanol at a flow rate of 1.1?mL?min^?1 directly into the nebulizer of the FAAS. The CPE variables and flow injection conditions affecting the analytical performance of the combined methodology was studied and optimized.

Results

Under the optimized conditions for 25?mL of preconcentrated solution, the enrichment factors were 51 and 44, and the limit of detections were 1.0 and 1.4?ng?mL^?1 for palladium and lead, respectively. Finally, the developed method was applied for the determination of palladium and lead in street dust, soil, radiology waste, catalytic converter, and urban aerosol samples.

Conclusions

Cloud-point extraction coupled with flow injection-FAAS was proposed as an effective preconcentration and separation method for Pd and Pb determination in radiology waste, road dust, soil, and urban aerosol samples. The most favorable feature of this method is its much higher selectivity, sensitivity, rapidity, good extraction efficiency, and employs the green chemistry concept, as it does not require the addition of toxic chemicals. In addition, this proposed method gives very low detection limits and good relative standard.     

Efficient biosorption of chromium(VI) ion by dry Araucaria leaves

Background

In this paper, batch removal of hexavalent chromium from aqueous solutions by Araucaria heterophylla leaves was investigated. The batch experiments were conducted to study the adsorption of metal species and effect of different pH, contact time, metal concentration, biosorbent concentration, and adsorption capacity.

Method

Freundlich and Langmuir??s isotherm model were used to describe the adsorption behavior, and the experimental results fitted Freundlich model well.

Results

The adsorption efficiency observed for all chromium concentrations, i.e., 1, 3, 5, and 10?mg/L was 100% and the equilibrium was achieved in 30?min for 1 and 3?mg/L, whereas for 5 and 10?mg/L, it was less than 60?min. FTIR spectra was taken to identify functional groups involved in the biosorption.

Conclusion

Thus, Araucaria leaves can be considered as one of the cheap and efficient biosorbent for toxic hexavalent chromium removal from natural or wastewaters.     

Airborne lead levels in the Korean peninsula: characterization of temporal and spatial patterns and cancer risk analysis

Introduction

This study collected long-term airborne lead concentrations in the Korean peninsula and analyzed their temporal, spatial, and cancer risk characterization.

Methods

Approximately, 12,000 airborne samples of total suspended particulate (TSP) were collected from 30 ambient air monitoring stations in inland (Daegu, Daejeon, Gwangju, and Seoul) cities and portal cities (Incheon, Busan, and Ulsan) over a period of 7?years (2004?C2010). High volume air samplers were employed to collect daily TSP samples during the second week of the consecutive months throughout the entire study period. The concentrations of Pb extracted from the TSP samples were analyzed using either inductively coupled plasma-atomic emission or flame atomic absorption spectrometry.

Results

The long-term high mean Pb concentrations were observed in the port cities including Incheon (88?±?18?ng/m³), Ulsan (61?±?7?ng/m³), and Busan (58?±?6?ng/m³). In the temporal analysis, seasonal mean Pb levels were relatively higher in winter and spring than those in summer and fall. In the spatial analysis, the mean Pb levels in spring, winter, and fall from Incheon, which showed the highest seasonal concentrations except summer, were 110?±?19, 101?±?18, and 76?±?23?ng/m³, respectively. In summer, the highest seasonal mean Pb level was observed in the largest industrial city and the second port city, Ulsan (78?±?15?ng/m³), followed by Incheon (65?±?13?ng/m³).

Conclusion

The estimated excess cancer risk analysis showed that inhalation of Pb could result in cancer for one or two persons per million of population in the Korean peninsula.     

Lead concentration increase in the hepatic and gill soluble fractions of European chub (Squalius cephalus)—an indicator of increased Pb exposure from the river water

Purpose

To examine if chronic exposure of feral fish to elevated Pb concentrations in the river water (up to 1???g?L^?1), which are still lower than European recommendations for dissolved Pb in surface waters (7.2???g?L^?1; EPCEU (Official J L 348:84, 2008)), would result in Pb accumulation in selected fish tissues.

Methods

Lead concentrations were determined by use of HR ICP-MS in the gill and hepatic soluble fractions of European chub (Squalius cephalus) caught in the Sutla River (Croatia?CSlovenia).

Results

At the site with increased dissolved Pb in the river water, soluble gill Pb levels (17.3???g?L^?1) were approximately 20 times higher compared to uncontaminated sites (0.85???g?L^?1), whereas the ratio between contaminated (18.1???g?L^?1) and uncontaminated sites (1.17???g?L^?1) was lower for liver (15.5). Physiological variability of basal Pb concentrations in soluble gill and hepatic fractions associated to fish size, condition, sex, or age was not observed, excluding the possibility that Pb increase in chub tissues at contaminated site could be the consequence of studied biotic parameters. However, in both tissues of Pb-exposed specimens, females accumulated somewhat more Pb than males, making female chubs potentially more susceptible to possible toxic effects.

Conclusions

The fact that Pb increase in gill and hepatic soluble fractions of the European chub was not caused by biotic factors and was spatially restricted to one site with increased dissolved Pb concentration in the river water points to the applicability of this parameter as early indicator of Pb exposure in monitoring of natural waters.     

Aquatic ecotoxicity assessment of a new natural formicide

Background, aim and scope

Agrochemicals could reach aquatic ecosystems and damage ecosystem functionality. Natural formicide could be an alternative to use in comparison with the more toxic formicides available on the market. Thus, the objective of this study was to assess the ecotoxicity of the new natural formicide Macex? with a battery of classical aquatic ecotoxicity tests.

Material and methods

Bacteria (Aliivibrio fischeri), algae (Pseudokirchneriella subcapitata), hydra (Hydra attenuata), daphnids (Daphnia magna), and fish (Danio rerio) tests were performed in accordance with international standardized methodologies.

Results

In the range of formicide concentrations tested (0.03 to 2.0?g?L^?1) EC₅₀ values varied from 0.49 to >2.0?g?L^?1, with P. subcapitata being the most sensitive species and H. attenuata and D. rerio the most tolerant species to this product in aqueous solutions.

Conclusions

This new formicide preparation can be classed as a product of low toxicity compared to the aquatic ecotoxicity of the most common commercialized formicides.     

Equilibrium and kinetics of adsorption of phosphate onto iron-doped activated carbon

Purpose

Two series of activated carbons modified by Fe (II) and Fe (III) (denoted as AC/N-Fe^II and AC/N-Fe^III), respectively, were used as adsorbents for the removal of phosphate in aqueous solutions.

Method

The synthesized adsorbent materials were investigated by different experimental analysis means. The adsorption of phosphate on activated carbons has been studied in kinetic and equilibrium conditions taking into account the adsorbate concentration, temperature, and solution pH as major influential factors.

Results

Maximum removals of phosphate are obtained in the pH range of 3.78?C6.84 for both adsorbents. Langmuir isotherm adsorption equation well describes the experimental adsorption isotherms. Kinetic studies revealed that the adsorption process followed a pseudo-second order kinetic model. Results suggest that the main phase formed in AC/N-Fe^II and AC/N-Fe^III is goethite and akaganeite, respectively; the presence of iron oxides significantly affected the surface area and the pore structure of the activated carbon.

Conclusions

Studies revealed that iron-doped activated carbons were effective in removing phosphate. AC/N-Fe^II has a higher phosphate removal capacity than AC/N-Fe^III, which could be attributed to its better intra-particle diffusion and higher binding energy. The activation energy for adsorption was calculated to be 22.23 and 10.89 kJ mol^?1 for AC/N-Fe^II and AC/N-Fe^III, respectively. The adsorption process was complex; both surface adsorption and intra-particle diffusion were simultaneously occurring during the process and contribute to the adsorption mechanism.     

Detection and quantitative analysis of 21 veterinary drugs in river water using high-pressure liquid chromatography coupled to tandem mass spectrometry

Introduction

The use of veterinary drugs in food production focuses on the control and improvement of animal health. The disadvantage of this practice is that pharmaceuticals and their metabolites are released into the environment, finding their way to natural water systems and becoming a potential risk to non-target organism.

Methods

This paper reports the development and validation of a quantitative method, based on high-performance liquid chromatography coupled to tandem mass spectrometry, for the simultaneous analysis of 21 veterinary drugs, antimicrobials, corticosteroids, coccidiostats and antifungal agents, in surface water.

Results

The precision of the method was established by calculating the mean recoveries, which were in the range of 94?C101%. The developed method was employed to conduct the first monitoring study on the presence of veterinary drugs in the Galicia region, Northwest of Spain and was applied to 235 surface water samples. Eleven veterinary drugs were detected at concentrations from below the limit of quantification to 2,978.6?ng?L^?1. Limits of detection and quantification were in the range of 6.2 (betamethasone, cortisone, decoquinate, dexamethasone, maduramycin, monensin, narasin, salinomycin, sulfachloropyridazine, sulfamethoxypyridazine and trimethoprim) to 12.5?ng?L^?1 (for the rest of the selected drugs) and 12.5 (betamethasone, cortisone, decoquinate, dexamethasone, maduramycin, monensin, narasin, salinomycin, sulfachloropyridazine, sulfamethoxypyridazine and trimethoprim) to 25.0?ng?L^?1 (for the remaining pharmaceuticals), respectively.

Conclusion

Sulfonamides were the group most frequently found, which are widely used in veterinary medicine.