水力除灰系统除砷模拟试验研究

针对金竹山电厂水力除灰系统采用闭路循环，溢流灰水再利用的方案，设计了模拟试验台，对灰水闭路循环后水质变化进行了探讨，取得了较为满意的结果．     

灰水回收用于循环冷却技术可行性研究

将火电厂冲灰水回水回收至冷却水母管，用作循环冷却水的补充水之灰水再利用方案尚属首创，小型模拟台等多项试验证明：该方案在技术上是可行的，灰水回收后不会增中冷却水系统和冲灰系统的结垢或腐蚀，且有较显著的经济效益。     

神东热电厂节水改造工程介绍

对神东公司热电厂水务管理现状进行了分析，并对已经实施和正在实施的节水方案进行总结。神东热电厂对补给水系统、循环水系统和热网水系统采取不同的节水措施，不同水质水各尽其用，大幅度提高了水的重复利用率，经济效益显著。     

灰水回收用于循环冷却水技术可行性研究

将火电厂冲灰水回水回收至冷却水母管，用作循环冷却水的补充水之灰水再利用方案尚属首创。小型模拟台等多项试验证明：该方案在技术上是可行的，灰水回收后不会增加冷却水系统和冲灰系统的结垢或腐蚀，且有较显著的经济效益。     

彭城电厂废水零排放的实施及问题探讨

针对目前水资源短缺状况，以彭城电厂为例提出了利用废水和灰场回收水作循环冷却水补充水的优化方案。并就废水零排放的实施及运行中发现的问题进行了分析与探讨。     

大同热电有限责任公司废水零排放工艺研究

通过对大同热电有限责任公司用水和废水的水质，水量调查，提出了新的水量平衡方案，达到了改进循环冷却水和冲灰水系统的运行状况，废水回收再用，节约用水和实现废水零排放的目的。     

锅炉酸洗柠檬酸废液处理

从理论上分析了经NaOH溶液预处理的柠檬酸酸洗废液再用灰水进行处理，降低COD值的可行性，实际应用结果表明，该方案可以达到“以废治废”的目的。     

荆门电厂冲灰水治理方案探讨

根据荆门电厂冲灰水系统摸底调查、小型试验及模拟试验的结果,结合灰水治理方面的有关经验,论证了荆门电厂冲灰水闭路循环治理灰水pH值和氟浓度超标方案的可行性。     

浓缩池溢流灰水回收防垢技术

分析了焦作电厂除灰、输灰系统特点及回水管道结垢原因,通过对浓缩池高ｐＨ值溢流灰水防垢处理回利利用技术的研究,提出了在灰水回收管道中加高效阻垢剂防垢处理后回收利用方案,并通过工业试验确定了投资阻垢剂的种类和数量。该技术解决因灰水回收管道结垢而严重影响输灰水生产和灰水再利用的难题,回收利用了灰水水资源,有良好的经济效益和环境效益。     

回用水用于湿法脱硫系统工艺水的水质要求

介绍了湿法脱硫系统中工艺水的用水情况及相应的水质要求,讨论了工艺水中一些主要的监测指标对脱硫系统运行的影响,并提出了工艺水水质的具体要求.根据脱硫工艺水系统的设计现状,提出了优化方案,可对电厂回用水的合理利用起到指导作用.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Methane generation from corncobs treated with xylanolytic consortia

Consortia were developed for the treatment of corncobs for use as a feedstock in a biogas fermentor. The treatment of corncobs with xylanolytic consortia enhanced the production of methane and biogas. All five consortia developed produced the maximum biogas and methane at a 6% loading rate and 20 days hydraulic retention time (HRT). The maximum biogas yield of 0.59m³/kg volatile solids (VS) with a methane content of 62% was produced with the KK-10 consortium. This was apparently due to a maximum hemicellulose degradation of 88%.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

Preparation and Biodegradation of Starch/Polycaprolactone Films

Starch granules were modified with trisodium trimetaphosphate (TSTP) and characterized by P³¹-NMR, FTIR and DSC. Seventy-micron films were prepared from modified starch and polycaprolactone blends by solvent casting technique. Three different types of films—PCL (100% polycaprolactone), MOD-ST/PCL (50% modified starch and 50% polycaprolactone blend) and NONMOD-ST/PCL (50% nonmodified starch and 50% polycaprolactone blends)—were prepared, and their thermal, mechanical, and morphologic properties were investigated to show the increased performance of PCL with the addition of starch and also the effect of modification. It was observed that with the addition of starch the Young's modulus of polycaprolactone was increased and became less ductile, whereas tensile strength and elongation at break values decreased. Biodegradation of these films was inspected under different aerobic environments with the presence of Pseudomonas putida, activated sludge, and compost. It was observed that whereas P. putida had almost no effect on degradation during 90 days, with the presence of activated sludge, considerable deformation of films was observed even in the first 7 days of degradation. In a compost environment, degradation was even faster, and all polymer films were broken into pieces within first 7 days of degradation and no film remained after 15 days.