The anthropogenic contribution to the organic load of the Lippe River (Germany). Part I: Qualitative characterisation of low-molecular weight organic compounds

GC/MS-screening analyses of water samples from the Lippe River, Germany, revealed the presence of a wide spectrum of low-molecular weight organic compounds ranging from non-polar constituents like aliphatic hydrocarbons to polar constituents like n-carboxylic acids and phenols. Most of the identified compounds could be attributed to anthropogenic input and are used as plasticizers, flame retardants, pharmaceutical drugs or fragrances. Some of them had rarely been noticed as organic pollutants of aquatic environments before. These are, among others, 9-methylacridine, the plasticizer 2,2,4-trimethyl-1,3-pentandioldiisobutyrate (TXIB), the surfactant 2,4,7,9-tetramethyl-5-decyne-4,7-diol (TMDD), triphenylphosphinoxide and the flame retardant tris(chloropropyl)phosphate. On the other hand, most of the identified trialkyl phosphates, pharmaceutical drugs and synthetic fragrances have been reported in surface waters by several authors so far. Input pathways of the detected compounds were traced back by sampling various input sources of organic matter such as discharges of wastewater and Lippe River tributaries. Several contaminants were ubiquitous in Lippe River water and also occurred in sewage effluent from a municipal sewage treatment plant and in samples from the tributaries. This observation suggests that they are typical sewage derived contaminants and have the potential to be used as anthropogenic molecular markers.     

Polycyclic organic material (POM) in urban air. Fractionation,chemical analysis and genotoxicity of particulate and vapour phases in an industrial town in Finland

Polycyclic organic material (POM) was collected by high-volume sampling on filter and on XAD-2 resin from the air of a small industrial town in Finland. Concurrent chemical analysis and the assays for genotoxic activity were performed on the particulate and the vapour phases of ambient air POM and their chemical fractions. Furthermore, correlations between seasonal meteorological parameters and POM concentrations were studied to reveal characteristic POM profiles for various emission sources. The range of total POM concentrations varied from 115 to 380 ng m⁻³ in late spring and from 17 to 83 ng m⁻³ in early winter. No direct correlation of ambient POM was seen with the temperature, but rather with the wind direction from various emission sources. Especially the low molecular weight compounds were associated with wind direction from industrial sources. Genotoxic activity, as detected by the Ames Salmonella/microsome test and the SCE assay in CHO cells, was found not only in the paniculate phase samples but also in the vapour phase. The polar fractions of some of the samples showed genotoxic activity, and also direct mutagenicity was observed with both the assay systems; these facts support the significance of compounds other than conventional polycyclic aromatic hydrocarbons (PAH) in the samples.     

New trends in the analytical determination of emerging contaminants and their transformation products in environmental waters

Since the so-called emerging contaminants were established as a new group of pollutants of environmental concern, a great effort has been devoted to the knowledge of their distribution, fate and effects in the environment. After more than 20 years of work, a significant improvement in knowledge about these contaminants has been achieved, but there is still a large gap of information on the growing number of new potential contaminants that are appearing and especially of their unpredictable transformation products. Although the environmental problem arising from emerging contaminants must be addressed from an interdisciplinary point of view, it is obvious that analytical chemistry plays an important role as the first step of the study, as it allows establishing the presence of chemicals in the environment, estimate their concentration levels, identify sources and determine their degradation pathways. These tasks involve serious difficulties requiring different analytical solutions adjusted to purpose. Thus, the complexity of the matrices requires highly selective analytical methods; the large number and variety of compounds potentially present in the samples demands the application of wide scope methods; the low concentrations at which these contaminants are present in the samples require a high detection sensitivity, and high demands on the confirmation and high structural information are needed for the characterisation of unknowns. New developments on analytical instrumentation have been applied to solve these difficulties. Furthermore and not less important has been the development of new specific software packages intended for data acquisition and, in particular, for post-run analysis. Thus, the use of sophisticated software tools has allowed successful screening analysis, determining several hundreds of analytes, and assisted in the structural elucidation of unknown compounds in a timely manner.     

Organic aerosols in the Miami area, USA: temporal variability of atmospheric particles and wet/dry deposition

Atmospheric particulate matter and both wet and dry deposition was collected over a period of nine months at one location in the metropolitan area of Miami, Florida. Molecular distributions and concentrations of n-alkanes, fatty acids, polycyclic aromatic hydrocarbons (PAHs) and hopanes were determined using weekly composite samples over this time period in order to determine temporal variability, and their possible dependence on climatic parameters such as temperature, rainfall and wind direction and frequency. Based on molecular distributions of the compounds studied, potential emission sources for the atmospheric particles were assessed and suggested to be mainly derived from automobile exhaust and natural sources. Although wet and dry deposition processes were observed to remove about equal amounts of organic aerosols from the Miami atmosphere, dry deposition was dominant in the removal of anthropogenically derived compounds such as PAHs and hopanes. Only very limited seasonal trends were observed, while wind direction and frequency was found to be the most important meteorological parameter controlling the temporal variability of the organic aerosols. This is the first detailed report of this nature for the Miami area.     

Effects of acid-washing filter treatment on quantification of aerosol organic compounds

The tests of standard mixtures and four sets of atmospheric particulate samples showed that an acid-wash (AW) pretreatment of fluorocarbon-coated glass fiber filters prior to aerosol sampling enhanced the quantifiable organic compounds for more than 29% (or 66 ng m⁻³); in particular, 47–273 ng m⁻³ (21–366%) more water-soluble organic compounds (WSOCs) were measured. When the acid-pretreated filters were employed, up to nine more organic species were measured in the individual daily samples. Because the acid pretreatment reduced the metal contaminants in the glass fiber filters, using the AW filters for aerosol sampling allows higher extraction recoveries of organic compounds. Since the fingerprinting compounds were more accurately determined when the aerosol samples were collected on the AW filters, better assessment of emission sources and toxicity of air pollutants can be obtained.     

Releases and transfers from petroleum and chemical manufacturing industries in Korea

Considerable effort and expense have been devoted to the estimation and acquisition of Toxics Release Inventory (TRI) data. To reduce the effort required and the number of reporting mistakes in the calculation of emissions, we developed an estimation program named TRIWIN after standardization of emission estimation techniques. The program was distributed to 6 petroleum and 150 chemical manufacturing companies, and emission data for 62 chemicals were collected and analyzed. From the TRIWIN-based results obtained, it was found that more than 90% of releases from petroleum and chemical manufacturing industries in Korea were emitted to atmosphere in 1999. Volatile organic compounds are major aerial contaminants and are released primarily via fugitive emission sources such as valves, pumps, or flanges. In addition, the effect of the application of point-source management was noticeable on the emission quantities. Consequently, TRIWIN not only helped reporters to implement TRI easily and accurately, but also identified emission sources, major pollutants in facilities, and provided a standard method of assessing the environmental impact of facilities.     

Identification and quantitation of dinaphthylsulfones in particulate matter of the Elbe river,Germany. Part VI of organic compounds as contaminants of the Elbe river and its tributaries

Gas chromatographic-mass spectrometric (GC/MS) analysis of particulate matter of the Elbe river and its tributaries Havel, Spree and Mulde revealed a group of three dinaphthylsulfone isomers as sedimentary and suspended particulate matter (SPM) contaminants. The mass spectra of dinaphthylsulfones are characterized by the molecular ion (m/z 318), and the naphthyl fragment ion m/z 127. Losses of HSO(2) and C(10)H(7)O from the molecular ion lead to different mass spectra for each isomer. The gas phase infrared spectra exhibit isomer specific bands in the spectral region between 900 and 700 wave numbers. A synthetic mixture of dinaphthylsulfones was used for isomer identification and the assignment of the gas chromatographic retention behaviour of the dinaphthylsulfone isomers. Quantitative GC/MS analysis of dinaphthylsulfones in 44 sediment and SPM samples provided comprehensive information on the overall distribution and distinct sources of dinaphthylsulfones in the Elbe river drainage system. The results indicate emissions of these compounds over prolonged times and their environmental stability in anaerobic sediments.     

Analysis of Ah receptor pathway activation by brominated flame retardants

Brominated flame-retardants (BFRs) are used as additives in plastics to decrease the rate of combustion of these materials, leading to greater consumer safety. As the use of plastics has increased, the production and use of flame-retardants has also grown. Many BFRs are persistent and have been detected in environmental samples, raising concerns about the biological/toxicological risk associated with their use. Most BFRs appear to be non-toxic, however there is still some concern that these compounds, or possible contaminants in BFRs mixtures could interact with cellular receptors. In this study we have examined the interaction of decabromodiphenyl ether, Firemaster BP4A (tetrabromobisphenol A), Firemaster PHT4 (tetrabromophthalic anhydride), hexabromobenzene, pentabromotoluene, decabromobiphenyl, Firemaster BP-6 (2,2^′,4,4^′,5,5^′-hexabromobiphenyl) and possible contaminants of BFR mixtures with the Ah receptor. Receptor binding and activation was examined using the Gel Retardation Assay and increased expression of dioxin responsive genes was detected using the reporter gene based CALUX assay. The results demonstrate the ability of BFRs to activate the AhR signal transduction pathway at moderate to high concentrations as assessed using both assays. AhR-dependent activation by BFRs may be due in part to contaminants present in commercial/technical mixtures. This was suggested by our comparative analysis of Firemaster BP-6 versus its primary component 2,2^′,4,4^′,5,5^′-hexabromobiphenyl. Some technical mixtures of brominated flame-retardants contain brominated biphenyls, dioxins or dibenzofurans as contaminants. When tested in the CALUX assay these compounds were found to be equivalent to, or more active than their chlorinated analogues. Relative effective potency values were determined from dose response curves for these brominated HAHs.     

Tidal salt marsh sediment in California, USA. Part 1: occurrence and sources of organic contaminants

Surface sediment samples (0-5 cm) from five tidal marshes along the coast of California, USA were analyzed for organic pollutants to investigate their relationship to land use, current distribution within marshes, and possible sources. Among the study areas, Stege Marsh, located in San Francisco Bay, was the most contaminated. Compared to San Francisco Bay, Stege Marsh had much higher levels of organic contaminants such as PCBs (polychlorinated biphenyls), DDTs, and chlordanes. At reference marshes (Tom's Point and Walker Creek in Tomales Bay), organic contaminants in sediments were very low. While PAHs (polycyclic aromatic hydrocarbons) were found at all of the study areas (22-13,600 ng g(-1)), measurable concentrations of PCBs were found only in the sediments from Stege Marsh (80-9,940 ng g(-1)). Combustion related (pyrogenic) high molecular weight PAHs were dominant in sediments from Stege and Carpinteria Marshes, while in sediments from Tom's Point and Walker Creek petroleum related (petrogenic) low molecular weight PAHs and alkyl-substituted PAHs were much more abundant than pyrogenic PAHs. PCB congener patterns in all of the Stege Marsh samples were the same and revealed that Aroclor 1248 was a predominant source. In all marshes, the sum of DDE and DDD accounted for more than 90% of total DDTs, indicating that DDT has degraded significantly. The ratios of p,p'-DDE to p,p'-DDD in sediments from Stege Marsh provide evidence of possible previous use of technical DDD. Chlordane ratios indicated that chlordanes have degraded slightly. Bis(2-ethylhexyl)phthalate (280-32,000 ng g(-1)) was the most abundant phthalate. The data indicates that Stege Marsh may be a source of contaminants that continue to be discharged into San Francisco Bay.     

Odor compounds released from different zones of two adjacent waste treatment facilities: Interactive influence and source identification

An integrated approach was applied to identify the key odorants comprising emissions from different zones in two adjacent waste treatment facilities (an aerobic biological treatment plant and an anaerobic landfill site), identify their precise sources, and distinguish the interactive influences between them. Seven odor families were investigated, including alcohols, terpenes, carbonyls, aromatics, volatile fatty acids (VFAs), sulfur compounds, and ammonia. Principal components analysis, characteristic molecular ratios, and ternary diagrams were used to differentiate the interactive influence of the odor sources. Among typical biotic compounds, terpenes were found to be more suitable as odor markers for their better fingerprinting character than sulfur compounds and VFAs. Ratios of p-cymene at sampling locations related to the biological treatment plant (aerobic status) were between 0.00 and 0.25, whereas those at landfill-related sampling points (anaerobic status) were between 0.25 and 1.0. The molecular ratio of terpenes was also found to be an appropriate means to differentiate between homologous and similar odor sources such as an aerobic biological treatment plant and anaerobic landfill.

Implications:?The aim of this work is to identify the key odorants comprising emissions from different zones in two adjacent waste treatment facilities, identify their precise sources, and distinguish the interactive influences between them. The emission of gaseous pollutants greatly affects the living quality of nearby residents, and odor complaints are becoming a major problem. In this study we utilized various pretreatment and analytical methods to obtain integrated emission information of gaseous pollutants. The results showed terpenes were found to be more suitable as odor markers for their better fingerprinting character than sulfur compounds and VFAs.     

A case study of contaminants on military ranges: Camp Edwards, Massachusetts, USA

An extensive investigation at the Camp Edwards, Massachusetts Military Reservation (MMR) demonstrates that assessment of groundwater and soil contamination at military ranges can be limited primarily to explosive-related compounds such as RDX, HMX, perchlorate, TNT and their transformation products. A modified analytical method is recommended to expand the list of explosives and to improve the detection limits. Analyses of metals, VOCs, SVOCs, and TICs are unnecessary. Soil samples may require the analyses of PAHs and PCNs for burn areas. Camp Edwards, as one of the few military ranges that have been exhaustively investigated for contaminants, is an ideal point of departure for evaluating other ranges. The permeable site soils promote leaching of contaminants and inhibit biotic and abiotic transformations. Moreover, the site has experienced an unusual extent of activities in its more than ninety years of active use. The recommendations in this report are based on data obtained for more than 200 analytes from more than 15,000 environmental samples.     

Emission factors of air toxics from semiconductor manufacturing in Korea

The development of local, accurate emission factors is very important for the estimation of reliable national emissions and air quality management. For that, this study is performed for pollutants released to the atmosphere with source-specific emission tests from the semiconductor manufacturing industry. The semiconductor manufacturing industry is one of the major sources of air toxics or hazardous air pollutants (HAPs); thus, understanding the emission characteristics of the emission source is a very important factor in the development of a control strategy. However, in Korea, there is a general lack of information available on air emissions from the semiconductor industry. The major emission sources of air toxics examined from the semiconductor manufacturing industry were wet chemical stations, coating applications, gaseous operations, photolithography, and miscellaneous devices in the wafer fabrication and semiconductor packaging processes. In this study, analyses of emission characteristics, and the estimations of emission data and factors for air toxics, such as acids, bases, heavy metals, and volatile organic compounds from the semiconductor manufacturing process have been performed. The concentration of hydrogen chloride from the packaging process was the highest among all of the processes. In addition, the emission factor of total volatile organic compounds (TVOCs) for the packaging process was higher than that of the wafer fabrication process. Emission factors estimated in this study were compared with those of Taiwan for evaluation, and they were found to be of similar level in the case of TVOCs and fluorine compounds.     

Cell bioassays for detection of aryl hydrocarbon (AhR) and estrogen receptor (ER) mediated activity in environmental samples

In vitro cell bioassays are useful techniques for the determination of receptor-mediated activities in environmental samples containing complex mixtures of contaminants. The cell bioassays determine contamination by pollutants that act through specific modes of action. This article presents strategies for the evaluation of aryl hydrocarbon receptor (AhR)-(hereafter referred as dioxin-like) or estrogen receptor (ER)-mediated activities of potential endocrine disrupting compounds (EDCs) in complex environmental mixtures. Extracts from various types of environmental or food matrices can be tested by this technique to evaluate their 2,3,7,8-tetrachlorodibenzop-dioxin equivalents (TCDD-EQs) or estrogenic equivalents (E₂-EQs) and to identify contaminated samples that need further investigation using resource-intensive instrumental analyses. Fractionation of sample extracts exhibiting significant activities, and subsequent reanalysis with the bioassays can identify important classes of contaminants that are responsible for the observed activity. Effect-directed chemical analysis is performed only for the active fractions to determine the responsible compounds. Mass-balance estimates of all major compounds contributing to the observed effects can be calculated to determine if all of the activity has been identified, and to assess the potential for interactions such as synergism or antagonism among contaminants present in the complex mixtures. The bioassay approach is an efficient (fast and cost effective) screening system to identify the samples of interest and to provide basic information for further analysis and risk evaluation.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in paddy soils and river sediments in Akita, Japan

Paddy soils and sediments from the Yoneshirogawa, Omonogawa, and Koyoshigawa River Basins in Akita were analyzed for polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). The levels and compositions in those samples including soils from non-agricultural areas (non-agricultural soils) were investigated using isomer-specific analysis to determine characteristic sources. The PCDD/PCDF compositions in the samples were compared with respect to possible sources. The PCDD/PCDF concentrations in paddy soils were much higher than those in the non-agricultural soils and much higher than those found in other parts of Japan. Although PCDD/PCDFs were ubiquitous in sediments from river sources to mouths of the respective river basins, those concentrations were much lower than those from paddy soils and non-agricultural soils, and from other parts of Japan. Comparison of PCDD/PCDF homologues and isomer compositions for samples indicated that compositions of paddy soils and sediments, except for those from river sources, had similar characteristics to PCDD/PCDFs originating from impurities in herbicides, 2,4,6-trichlorophenyl 4-nitrophenyl ether (CNP) and pentachlorophenol (PCP), and that compositions of river-source sediments and non-agricultural soils resembled those of atmospheric depositions. Results of statistical analyses suggest that PCDD/PCDF contamination of paddy soils and sediments is attributable mainly to three sources: CNP, PCP, and atmospheric deposition. Results of this study also demonstrate that CNP and PCP are not only important contaminants of local areas of Japan, but that they exist throughout Akita, in northern Japan. We therefore conclude that PCDD/PCDF pollution caused by those compounds has a widespread influence on paddy soils and river sediments in Japan.     

Occurrence of polybrominated diphenyl ethers (PBDEs) and 2,2’,4,4’,5,5’-hexabromobiphenyl (BB-153) in water samples from the Diep River, Cape Town, South Africa

Until recently, studies reporting the concentrations of polybrominated diphenyl ethers (PBDEs) as well as polybrominated biphenyls (PBBs) are generally scarce in the literature. Consequently, this study was aimed to investigate the occurrence and concentrations of certain PBDE congeners (BDE 28, 47, 100, 99, 154, 153, 183 and 209) and BB 153 in river water samples collected bi-monthly from the Diep River. The routine analyses of the target compounds were performed using a high-capillary GC–microelectron capture detection, while their structural elucidation was assessed using GC-TOF-MS technique. The overall mean concentrations of the sum of the eight PBDE congeners were 2.60, 4.83 and 4.29 ng/L for the upstream, point of discharge and downstream sampling points, respectively. Similarly, the overall mean concentrations of BB 153 were 0.25, 4.85 and 1.56 ng/L for the upstream, point of discharge and downstream sampling points, respectively. BDE 47 was the dominant congener found in these samples contributing between 19 and 26 % to the total PBDEs across the sampling points. The statistical analyses performed on the results obtained showed that all the congeners, except BDE 209 in certain instances, had strong positive correlations with one another, thus suggesting that these contaminants could be emanating from the same source. In this study, potential sources of these pollutants other than WWTP discharges into the investigated river were also identified. However, the relatively high concentrations of the target compounds found at the point of discharge sampling point coupled with the large volume of treated effluent being discharged suggested that the contributions from this source could be very significant over time.     

Survey of phthalates, alkylphenols, bisphenol A and herbicides in Spanish source waters intended for bottling

Background, aim and scope

Groundwaters and source waters are exposed to environmental pollution due to agricultural and industrial activities that can enhance the leaching of organic contaminants. Pesticides are among the most widely studied compounds in groundwater, but little information is available on the presence of phthalates, alkylphenols and bisphenol A. These compounds are used in pesticide formulations and represent an emerging family of contaminants due to their widespread environmental presence and endocrine-disrupting properties. Knowledge on the occurrence of contaminants in source waters intended for bottling is important for sanitary and regulatory purposes. So the aim of the present study was to evaluate the presence of phthalates, alkylphenols, triazines, chloroacetamides and bisphenol A throughout 131 Spanish water sources intended for bottling. Waters studied were spring waters and boreholes which have a protection diameter to minimize environmental contamination.

Materials and methods

Waters were solid-phase extracted (SPE) and analysed by gas chromatography coupled to mass spectrometry (GC-MS). Quality control analysis comprising recovery studies, blank analysis and limits of detection were performed.

Results and discussion

Using SPE and GC-MS, the 21 target compounds were satisfactorily recovered (77?C124?%) and limits of quantification were between 0.0004 and 0.029???g/L for pesticides, while for alkylphenols, bisphenol A and phthalates the limits of quantification were from 0.0018???g/L for octylphenol to 0.970???g/L for bis(2-ethylhexyl) phthalate. Among the 21 compounds analysed, only 9 were detected at levels between 0.002 and 1.115???g/L. Compounds identified were triazine herbicides, alkylphenols, bisphenol A and two phthalates. Spring waters or shallow boreholes were the sites more vulnerable to contaminants. Eighty-five percent of the samples did not contain any of the target compounds.

Conclusions

Target compounds were detected in a very low concentration and only in very few samples. This indicates the good quality of source waters intended for bottling and the effectiveness of the protection measures adopted in Spain. None of the samples analysed exceeded the maximum legislated levels for drinking water both in Spain and in the European Union.     

Sulfonated derivatives of naphthalene in water samples of an Italian river

Naphthalenesulfonates were found in water samples of the Italian river Bormida. Samples were collected at increasing distances from the point of emission of pollutants, and their analyses showed that these compounds can persist in river water and that they can propagate for considerable distances.     

Elevated in-home sediment contaminant concentrations - the consequence of a particle settling-winnowing process from Hurricane Katrina floodwaters

Sediment samples were collected from two homes which were flooded in the wake of Hurricane Katrina in August 2005. The samples were analyzed for trace metals and semi-volatile organic compounds using techniques based on established EPA methods. The data showed higher concentrations of some metals and semi-volatile organic pollutants than reported in previous outdoor sampling events of soils and sediments. The Lake Pontchartrain sediments became resuspended during the hurricane, and this material subsequently was found in the residential areas of New Orleans following levee breaches. The clay and silt particles appear to be selectively deposited inside homes, and sediment contaminant concentrations are usually greatest within this fraction. Re-entry advisories based on outdoor sample concentration results may have under-predicted the exposure levels to homeowners and first responders. All contaminants found in the sediment sampled in this study have their origin in the sediments of Lake Pontchartrain and other localized sources.     

Emission Factors of Air Toxics from Semiconductor Manufacturing in Korea

Abstract

The development of local, accurate emission factors is very important for the estimation of reliable national emissions and air quality management. For that, this study is performed for pollutants released to the atmosphere with source-specific emission tests from the semiconductor manufacturing industry. The semiconductor manufacturing industry is one of the major sources of air toxics or hazardous air pollutants (HAPs); thus, understanding the emission characteristics of the emission source is a very important factor in the development of a control strategy. However, in Korea, there is a general lack of information available on air emissions from the semiconductor industry. The major emission sources of air toxics examined from the semiconductor manufacturing industry were wet chemical stations, coating applications, gaseous operations, photolithography, and miscellaneous devices in the wafer fabrication and semiconductor packaging processes. In this study, analyses of emission characteristics, and the estimations of emission data and factors for air toxics, such as acids, bases, heavy metals, and volatile organic compounds from the semiconductor manufacturing process have been performed. The concentration of hydrogen chloride from the packaging process was the highest among all of the processes. In addition, the emission factor of total volatile organic compounds (TVOCs) for the packaging process was higher than that of the wafer fabrication process. Emission factors estimated in this study were compared with those of Taiwan for evaluation, and they were found to be of similar level in the case of TVOCs and fluorine compounds.     

Indoor- and outdoor-derived contaminants in urban and rural homes in Ottawa, Ontario, Canada

Indoor and outdoor air contaminants have largely been treated separately in studies of their respective effects on respiratory and nonrespiratory health. In this paper, we report the results of a comprehensive study of key contaminants in 10 urban and 10 rural homes in Ottawa, Ontario, Canada. The analyses included house dust mite and cat allergens along with the fungal inflammatory polysaccharide beta1,3-D-glucan in settled dust and fine particulate matter, coarse particulate matter, ergosterol, glucan, and endotoxin from air samples. In addition, black carbon was continuously measured for 7 days. A detailed physical assessment of the house and patterns of use were undertaken, including a careful inspection for mold and water damage, as well as measurements of air leakage. The performance of the houses and the range and distribution of the contaminants measured were largely similar to that of previous Canadian studies. For certain combinations, it is thought that the presence of both allergen and inflammatory materials increases asthma symptoms. House-by-house comparisons of airborne concentrations of inflammatory compounds measured (endotoxin, fine particulate matter, and fungal glucan) with dust mite allergens indicated that certain houses had relatively higher amounts of both kinds of materials.