Fluoride sorption by treated fly ash: kinetic and isotherm studies

High fluoride levels in drinking water have become a critical health hazard. In the present study, the performance of magnesia-loaded fly ash adsorption in the removal of fluoride from aqueous solution was investigated in a batch study. The effect of contact time, dosage, pH, temperature and agitation speed was studied at different values. The maximum removal efficiency was 88 % at 150 min. The effective dose of adsorbent was found to be 2.5 g/l. The optimum pH was found to be at pH 4. Kinetic studies and isotherm studies were also performed to understand the ability of the adsorbents. The monolayer adsorption capacity determined from the Langmuir adsorption equation was found to be 11.61 mg/g. The kinetic measurements suggested the involvement of pseudo-second-order kinetics in adsorption and were controlled by a particle diffusion process. Overall, the results of this study suggest that magnesia-loaded fly ash is an environmentally friendly, efficient and low-cost adsorbent, useful for the removal of fluoride from aqueous solution.     

Adsorption of Crystal Violet Dye from Aqueous Solution by Poly(Acrylamide-<Emphasis Type="Italic">co</Emphasis>-Maleic Acid)/Montmorillonite Nanocomposite

Poly(acrylamide-co-maleic acid)/montmorillonite nanocomposites, were synthesized via in situ polymerization with different maleic acid and MMT content. The capability of the hydrogel for adsorption of crystal violet (CV) was investigated in aqueous solutions at different pH values and temperatures. The pseudo-second-order kinetics model could fit successfully the adsorption kinetic data. The effects of maleic acid to acrylamide molar ratio (MA_R), weight percent of MMT (MMT%), the pH of medium and the solution temperature (T) on the CV adsorption capacity (q _e ) of adsorbents were studied by Taguchi experimental design approach. The results indicated that increasing the MMT% leads to a greater q _e . The q _e value of adsorbents increased also with increasing both MA_R and pH, while reduced when the temperature of medium increased. The relatively optimum conditions to achieve a maximum CV adsorption capacity for P(AAm/MA)/MMT adsorbents were found as: 0.06 for MA_R and 5 % of MMT%, medium pH = 7 and T = 20 °C.     

Adsorption of Ammonium by Graphene Oxide-Based Composites Prepared by UV Irradiation and Using as Slow-Release Fertilizer

A novel sodium alginate-grafted poly(acrylic acid)/graphene oxide (NaAlg-g-PAA/GO) composite hydrogel was prepared via ultraviolet irradiation, and characterized by infrared spectroscopy spectrometer. X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. It was employed to adsorb NH₄⁺ from aqueous solution and used as slow-release nitrogen fertilizers (SNFs). Result indicated that the adsorption process for NH₄⁺ reached equilibrium within 50 min, with the adsorption capacity of 6.6 mmol g^?1 even if 30 wt% GO was incorporated. The results of adsorption kinetic and isotherm were well described by the pseudo-second-order and Freundlich model. The thermodynamics analysis showed the adsorption process was spontaneous. The study indicated excellent water-holding ratio of soil with 2 wt% SNFs was 81.2%, and nitrogen release was up to 55.1% within 40 days in soil. Overall, NaAlg-g-PAA/GO could be considered as an efficient adsorbent for the recovery of nitrogen with the agronomic reuse as a fertilizer.     

Adsorption Kinetics of Dyes in Single and Binary Systems Using Cyanoguanidine-Crosslinked Chitosan of Different Deacetylation Degrees

The crosslinking of chitosan with cyanoguanidine shows some advantages, such as the improved the stability in acid solutions and the decrease of adsorbent cost. In this work, cyanoguanidine-crosslinked chitosan and pure chitosan were prepared to apply in the adsorption of Food Yellow 4 (FY4) and Food Blue 2 (FB2), in single and binary systems. Effects of pH and deacetylation degree (DD) of chitosan in adsorption were evaluated. The adsorbents were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The kinetic data were analyzed by pseudo-first order, pseudo-second order and Avrami models. The conditions of pH 3 and DD 95% were the more suitable to reach the highest adsorption capacities in all experimental assays. Under these conditions, the adsorption capacities for FY4 were approximately of 392 and 200 mg g^?1 and, for FB2 were approximately of 370 and 184 mg g^?1, respectively, in the single and binary systems. The Avrami model was suitable to represent the kinetic curves in all conditions, and the highest adsorption capacities were found for FY4 in binary aqueous system, being for the pure chitosan of 229 mg g^?1 and crosslinked chitosan of 218 mg g^?1. The Langmuir and extended Langmuir models presented a good fit to the equilibrium data in both systems. It was found that, the chitosan crosslinked with cyanoguanidine improved the chemical stability of chitosan as adsorbent.     

Assessment of Potential Capability of Water Bamboo Leaves on the Adsorption Removal Efficiency of Cationic Dye from Aqueous Solutions

Removal of toxic pollutants from water and wastewater is becoming an important process with the increase of industrial activities. The present study focused on assessing the suitability and efficiency of water bamboo leaves (WBL) for the removal of cationic dye from aqueous solutions. The effect of different variables in the batch method including solution pH (2–12), initial dye concentration (50–250 mg L^?1), adsorbent dose (0.05–0.30 g), contact time (5–180 min) and temperature (283–333 K) on the dye removal was investigated. The adsorption kinetics was discussed in view of four kinetics models. The results showed that the pseudo-second-order kinetics model described dye adsorption on WBL very well. The experimental equilibrium data were also tested by four isotherm models. It was found that adsorption of dye on WBL fitted well with the Langmuir isotherm model, implying the binding energy on the whole surface of the adsorbent was uniform and the dye molecules onto the surface of the adsorbent were monolayer coverage. Calculation of various thermodynamic parameters of the adsorption process indicated feasibility and exothermic nature of dye adsorption.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

Modified Sugarcane Bagasse with Tartaric Acid for Removal of Diazonium Blue from Aqueous Solutions

The present study concerns with exploring the possibility of using of tartaric acid pretreated sugarcane bagasse (SCB) for removing diazonium blue (DB) from aqueous solutions. The effect of different factors on the efficiency of the adsorbent for the DB dye removal was investigated, including initial dye concentration, contact time, SCB dosage and SCB particle size. Langmuir, Freundlich, Tempkin and D–R isothermal models have been employed to analyze the adsorption equilibrium data. It was found that the adsorption of the dye fits well with the D–R model. The adsorption kinetics was also done applying four kinetic models. The regression equation coefficients refer to fitting the data to the second-order kinetic equation for removal of the DB dye. It is probable that the rate limiting step is a chemical adsorption between the adsorbent and the dye. This chemisorption process is further confirmed from the energy value of 15.1 kJ mol^?1 deduced from the D–R isotherm.     

Utilization of the used tire rubber particle in hydrogen sulfide control

The adsorption capacity of fine rubber particle media (FRPM) derived from discarded vehicle tires and the consumer wasted rubber sources was evaluated for hydrogen sulfide treatment. H₂S breakthrough tests were performed at various zinc contents, temperatures, and packing quantities. High zinc concentrations increased the adsorption capacity of FRPM significantly. H₂S removal by FRPM was optimized at a packing quantity of 75 % of the column volume, and the adsorption capacity increased with reactor temperature within the range of 20–85 °C. The regeneration of ZnCl₂ solution was reliable for increasing regeneration capacity of the FRPM-adsorbed H₂S. FRPM seems to be an attractive alternative of H₂S adsorbents in terms of cost effectiveness compared to traditional materials.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

The Removal of Acid Violet 90 from Aqueous Solutions Using PANI and PANI/Clinoptilolite Composites: Isotherm and Kinetics

Polyaniline (PANI) and polyaniline/Gördes-clinoptilolite (PANI/GC) composite materials were synthesized by the chemical oxidative polymerization technique and used in the adsorption of Acid Violet 90 metal-complex dye (AV 90). The samples were characterized by X-ray diffractions, nitrogen adsorption–desorption isotherms, scanning electron microscopes and Fourier transform infrared. The effect of initial pH (2–8), sorbent dosage (0.5–4.0 g/L) and initial dye concentrations (50–400 mg/L) on adsorption onto PANI and PANI/GC were examined in a batch system. Langmuir, Freundlich and Temkin isotherm models were used to investigate the adsorption mechanism of AV 90 on PANI and PANI/GC. Langmuir isotherm model for PANI/GC and Freundlich isotherm model for PANI were fitted well with the experimental data. The highest dye uptake capacities were obtained with Langmuir isotherm model as 153.85 mg/g and 72.46 mg/g for PANI and PANI/GC, respectively. In order to determine the adsorption kinetics, pseudo first-order and second-order kinetic models were studied. As a result, the adsorption of AV 90 dye on PANI and PANI/GC was better identified with Pseudo second-order kinetic model than the first one.     

Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Itaconic Acid Grafted Starch Hydrogels as Metal Remover: Capacity,Selectivity and Adsorption Kinetics

Hydrogels were synthesized by free radical graft copolymerization of itaconic acid (IA) onto corn starch (S-g-IA). For this purpose, potassium permanganate (KMnO₄)-sodium bisulfite (NaHSO₃) was used as redox initiation system. The formation of grafted starches was confirmed by Fourier transform infrared spectroscopy, wide angle X-ray scattering, thermogravimetric analysis and scanning electron microscopy. The effect of monomer concentration, neutralization, addition of crosslinking agent, N,N-bismetilenacrilamide (MBAm), and initiator concentration on grafting efficiency and adsorption capacity of the starch hydrogels was investigated. It was demonstrated that the introduction of carboxyl and carbonyl groups promoted starch hydration and swelling. Grafting degree increased with the decrease of monomer concentration, increase of initiator concentration, grade of neutralization and the addition of MBAm without neutralization. Remarkably the resulting materials exhibited water absorption capacities between 258 and 1878% and the ability to adsorb metal ions. It was experimentally confirmed the metal uptake, obtaining the higher adsorption capacity (q _e  = 35 mg/g) for the product prepared with the pre-oxidation and lower initiator concentration. The removal capacity order was Pb²⁺>Ni²⁺>Zn²⁺>Cd²⁺. Moreover, the experimental kinetic and the equilibrium adsorption data for Ni²⁺ and Pb²⁺ were best fitted to the pseudo-second order and Freundlich isotherm models, respectively. This work describes for the first time the preparation of metal removal hydrogels based on starch and itaconic acid using the pair redox system KMnO₄/NaHSO₃, which avoids the starch hydrolysis and allows itaconic acid grafting incorporation without the requirement of more reactive comonomers.     

Adsorptive Removal of Diuron Herbicide on Carbon Nanotubes Synthesized from Plastic Waste

In this study, carbon nanotubes (CNTs) were synthesized from waste polyethylene bottles and their use as an adsorbent for the removal of diuron herbicide from aqueous solution was evaluated. Batch adsorption was performed by varying adsorbent dosage, initial concentration, contact time, and temperature. Kinetic models applied to experimental data indicated that the pseudo-second-order model had the best fit. The equilibrium data were analyzed using different isotherm models. The adsorption capacity of CNTs for diuron removal, determined using the Hill isotherm, was approximately 40.37 mg/g at 303 K. From thermodynamic studies, the values of ΔH° (kJ/mol) and ΔS° [kJ/(mol K)] were calculated as ?17.307 and ?0.0528, respectively, which suggested that the adsorption process was exothermic. The negative values of ΔG° at three different temperatures indicated that adsorption of diuron on CNTs was favorable.     

Removal of Oil from Water by Calcium Alginate Hydrogel Modified with Maleic Anhydride

Calcium alginate hydrogel was prepared and used as a biosorbent for the removal of oil from aqueous solutions. Calcium alginate hydrogel was further chemically modified by esterification with maleic anhydride. The changes in the physicochemical properties of maleic anhydride modified calcium alginate were investigated via multiple techniques (FTIR, SEM, BET and DSC/TGA). Adsorption batch experiments were carried out to compare the oil adsorption capacities of native and modified calcium alginates. Adsorption experiments were carried out as a function of solution pH, temperature and ionic strength to determine the optimal conditions for the adsorption of oil. Equilibrium and kinetic studies were conducted for the modified alginate. Results revealed that the maleic anhydride modification of calcium alginate improved its adsorption capacity towards oil. Higher adsorption capacities of modified alginate were attained at lower temperatures (20 °C), higher ionic strengths (1.0 M NaCl) and within the pH range of 5–9. The oil adsorption data obtained for modified alginate could be better described by the first order kinetic model (R²?=?0.981) and the BET equilibrium isotherm (R²?=?0.984). The maximum monolayer adsorption capacity predicted by the BET model for the modified calcium alginate was found to be 143.0 mg/g.     

Biosorptive removal of Pb(II) and Cu(II) from wastewater using activated carbon from cassava peels

The ability of activated carbon from cassava peels to remove heavy metals like Cu(II) and Pb(II) from hospital wastewater was investigated. The study showed that a pH of 8 was the best for the sorption of both metal ions onto the biosorbent. The time-dependent experiments for the metal ions showed that the binding of the metal ions to the biomass was rapid and occurred within 20–120 min. Sorption efficiency increased with a rise in adsorbent dosage. It increased from 12 to 73 % for Pb(II) and 26 to 79 % for Cu(II) when the adsorbent dose increased from 2 to 12 g. An increase in temperature led to an increase in sorption for both metal ions. The Langmuir model showed that the biomass has a higher sorption capacity for Cu(II) than Pb(II), with q _m = 5.80 mg g^?1 for Pb(II) and 8.00 mg g^?1 for Cu(II). The Freundlich isotherm K _f was 1.4 for Pb(II) and 1.8 for Cu(II), indicating a preferential sorption of Cu(II) onto the biosorbent. Adsorption capacity was found to decrease with an increase in particle sizes. Sorption occurred by physical mechanisms and was mainly controlled by intraparticle diffusion.     

Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na⁺-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na⁺-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na⁺-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.     

Selective Lead(II) Adsorption and Flocculation Characteristics of the Grafted Sodium Alginate: A Comparative Study

Synthesis of sodium alginate-g-poly(acrylamide-co-N-methylacrylamide) [S-III], sodium alginate-g-poly(N-methylacrylamide-co-N,N-dimethylacrylamide) [S-II], sodium alginate-g-poly(acrylamide-co-N,N-dimethylacrylamide) [S-I]. Sodium alginate-g-poly(N,N-dimethylacrylamide) [SAG-g-PDMA] and sodium alginate-g-poly(acrylamide) [SAG-g-PAM] were prepared by solution polymerization technique using potassium peroxydisulfate as the initiator at 70?°C in water medium. The graft copolymers were characterized by FTIR and NMR (¹H and ¹³C) spectroscopy, SEM and XRD studies. All the five graft copolymers were used to remove Pb(II) ions from the aqueous solution and also in flocculation studies of kaolin clay (1.0 wt%), silica (1.0 wt%) and iron ore slime (0.25 wt%) suspensions. A comparative studies of all the five graft copolymers were also made in both the two cases. The Pb(II) ion removal capacity of all the graft copolymers follows the order S-III?>?SAG-g-PAM?>?S-II?>?SAG-g-PDMA?>?S-I. But the flocculation performance of the graft copolymers follows the order S-II?>?S-I?>?S-III?>?SAG-g-PDMA?>?SAG-g-PAM. S-III was also used for the competitive metal ion removal with Hg(II), Cd(II), Cu(II) and Zn(II). Pb(II) adsorption of S-III (the best Pb(II) ion adsorber) follows pseudo second order rate equation and Langmuir adsorption isotherm.     

Preparation of Porous Nanofibers from Electrospun Polyacrylonitrile/Polyvinylidene Fluoride Composite Nanofibers by Inexpensive Salt Using for Dye Adsorption

The high surface area of porous nanofibers enhances their performance for many applications. The present study investigated electrospinning and dye adsorption properties of polymeric nanofibers which were porous by various types of salts. The salt/polyacrylonitrile/polyvinylidene fluoride composite nanofibers were electrospun, and the inexpensive salts such as sodium chloride (NaCl), sodium bicarbonate (NaHCO₃), or calcium chloride (CaCl₂) was used to manufacture the porous fibers. Subsequently, the salt was removed by a selective dissolution, and salt extraction of nanofibers was performed with the solution of hydrochloric acid (10 wt%). Salt/PVDF/PAN and porous PVDF/PAN composite nanofibers have been applied to dye adsorption of solution. The characteristics of nanofibers were studied by Fourier transform infrared microscopy (FTIR) and scanning electron microscopy (SEM) analysis. FTIR showed that the salt was extracted from PVDF/PAN nanofibers successfully, and SEM indicated that many pores were aligned with the nanofibers. The adsorption capacity of salt nanofibers webs and porous nanofibers webs for Basic Blue 41 were compared with each other, and porous fibers were obtained from NaHCO₃ having the highest dye adsorption value. Adsorption of dyes follows the Langmuir isotherm and pseudo-second order kinetics.     

Preparation,Characterization, and Rapid Adsorption of Hg<Superscript>2+</Superscript> on Nanoscale Aramid-based Adsorbent

A series of nanaoscale aramid-based adsorbents were prepared by the functionalization of poly (p-phenylene terephthalamide) (PPTA) with different content of ethylenediamine (EDA). Their structures were characterized by field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and elemental analysis. Metal ions, including Hg²⁺, Pb²⁺, Ag⁺, Cu²⁺, Cd²⁺, and Ni²⁺ were chosen as the models to explore the binding behaviors of PPTA–ECH–EDA in aqueous medium. Results showed that PPTA–ECH–EDA exhibited higher adsorption capacity for Hg²⁺ due to their nanoscale structures. In particular, the adsorption rate was so high that equilibrium was achieved within 15 min for Hg²⁺. The adsorption of Hg²⁺ on PPTA–ECH–EDA followed the pseudo second-order model well. Langmuir and Freundlich models were employed to fit the isothermal adsorption, and the results revealed that Freundlich isotherm was a better model to predict the experimental data. The adsorption mechanism was revealed by X-ray photoelectron spectroscopy. It is preconceived that PPTA–ECH–EDA could be used as an effective adsorbent for fast removal of heavy ions from wastewater.