Analysis of air quality data near roadways using a dispersion model

We used a dispersion model to analyze measurements made during a field study conducted by the U.S. EPA in July–August 2006, to estimate the impact of traffic emissions on air quality at distances of tens of meters from an eight-lane highway located in Raleigh, NC. The air quality measurements consisted of long path optical measurements of NO at distances of 7 and 17 m from the edge of the highway. Sonic anemometers were used to measure wind speed and turbulent velocities at 6 and 20 m from the highway. Traffic flow rates were monitored using traffic surveillance cameras. The dispersion model [Venkatram, A., 2004. On estimating emissions through horizontal fluxes. Atmospheric Environment 38, 2439–2446] explained over 60% of the variance of the observed path averaged NO concentrations, and over 90% of the observed concentrations were within a factor of two of the model estimates.Sensitivity tests conducted with the model indicated that the traffic flow rate made the largest contribution to the variance of the observed NO concentrations. The meteorological variable that had the largest impact on the near road NO concentrations was the standard deviation of the vertical velocity fluctuations, σ_w. Wind speed had a relatively minor effect on concentrations. Furthermore, as long as the wind direction was within ±45° from the normal to the road, wind direction had little impact on near road concentrations. The measurements did not allow us to draw conclusions on the impact of traffic-induced turbulence on dispersion. The analysis of air quality and meteorological observations resulted in plausible estimates of on-road emission factors for NO.     

The influence of meteorological conditions and stringent emission control on high TSP episodes in istanbul

Istanbul has faced serious air pollution problems since the mid-80s. This is mainly due to particulate air pollution coming from poor quality lignite in areas, which are heavily populated and industrialized. As a consequence of severe air pollution problems, stringent control on the emissions in the city started in the year of 1994. In this work, in order to study the relationship between emissions and meteorological conditions, an assessment of air pollution episodes and air pollution potential in the city is presented for the terms at the changed emission schedule as the influence of an emission reduction strategy. The influence of meteorological conditions on the TSP (total suspended particulates) levels is considered for two consecutive winter periods. On this occasion, the city has faced different TSP levels and episode characteristics depending on stringent emission reductions covering the banned, poor-quality lignite and fuel switching. For this purpose, climatological conditions and air quality analyses were performed.     

Assessment of contribution of SO2 and NO2 from different sources in Jamshedpur region, India

Contribution of pollution from different types of sources in Jamshedpur, the steel city of India, has been estimated in winter 1993 using two approaches in order to delineate and prioritize air quality management strategies for the development of region in an environmental friendly manner. The first approach mainly aims at preparation of a comprehensive emission inventory and estimation of spatial distribution of pollution loads in terms of SO₂ and NO₂ from different types of industrial, domestic and vehicular sources in the region. The results indicate that industrial sources account for 77% and 68% of the total emissions of SO₂ and NO₂, respectively, in the region, whereas vehicular emissions contributed to about 28% of the total NO₂ emissions. In the second approach, contribution of these sources to ambient air quality levels to which the people are exposed to, was assessed through air pollution dispersion modelling. Ambient concentration levels of SO₂ and NO₂ have been predicted in winter season using the ISCST3 model. The analysis indicates that emissions from industrial sources are responsible for more than 50% of the total SO₂ and NO₂ concentration levels. Vehicular activities contributed to about 40% of NO₂ pollution and domestic fuel combustion contributed to about 38% of SO₂ pollution. Predicted 24-h concentrations were compared with measured concentrations at 11 ambient air monitoring stations and good agreement was noted between the two values. In-depth zone-wise analysis of the above indicates that for effective air quality management, industrial source emissions should be given highest priority, followed by vehicular and domestic sources in Jamshedpur region.     

Sulfur dioxide dispersion and source contribution to receptors of downtown Patras, Greece

Background The development of the city of Patras, including harbour relocation, in conjunction with the protection of the regional ecosystems, requires air quality assessment and management. For this reason, a model applicable in the Patras area is necessary and valuable. The goal of this study was to validate a model suitable for predicting the dispersion of sulfur dioxide (SO₂), based on particular activity, topography and weather conditions. Methods We used the US-EPA ISCLT3 integral dispersion model to predict SO₂ concentrations for Patras, Greece. We assumed that the major contribution to Patras air pollution came from central heating, harbour and traffic. We calculated traffic emissions using COPERTIII. Results and Discussion Assigning suitable values of the mixing height, the model predicted the local and spatial distribution of the mean monthly SO₂ concentrations in downtown Patras, as well computed the contribution of the SO₂ emissions originating from each particular source at each receptor location on a seasonal and annual basis. The comparison between predictions and measurements shows that the model performance for estimating the SO₂ concentrations and period pattern is satisfactory. Conclusion The mixing height was the critical parameter for calibrating the model. Model validation promises satisfactory predictions for SO₂ pollution levels on monthly basis. Recommendations and Outlook The model could be used in predicting SO₂ concentrations and source contribution for several downtown Patras receptors using pertinent meteorological and emission information. It could be also extended to predict the dispersion of other primary air pollutants. The calibrated model predictions could be used to fill gaps in monitoring data, saving money and time, and help in assess and manage air quality as Patras develops.     

Emissions Variability Processor (EMVAP): Design,evaluation, and application

Emissions of pollutants such as SO₂ and NOx from external combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup, shutdown, and maintenance/malfunction. While monitoring will automatically reflect variability from both emissions and meteorological influences, dispersion modeling has been typically conducted with a single constant peak emission rate. To respond to the need to account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, we have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates. Based upon initial AERMOD modeling of from 1 to 5 years of actual meteorological conditions, EMVAP is used as a postprocessor to AERMOD to simulate hundreds or even thousands of years of concentration predictions. This procedure uses emissions varied hourly with a Monte Carlo sampling process that is based upon the user-specified emissions distribution, from which a probabilistic estimate can be obtained of the controlling concentration. EMVAP can also accommodate an advanced Tier 2 NO₂ modeling technique that uses a varying ambient ratio method approach to determine the fraction of total oxides of nitrogen that are in the form of nitrogen dioxide. For the case of the 1-hr National Ambient Air Quality Standards (NAAQS, established for SO₂ and NO₂), a “critical value” can be defined as the highest hourly emission rate that would be simulated to satisfy the standard using air dispersion models assuming constant emissions throughout the simulation. The critical value can be used as the starting point for a procedure like EMVAP that evaluates the impact of emissions variability and uses this information to determine an appropriate value to use for a longer term (e.g., 30-day) average emission rate that would still provide protection for the NAAQS under consideration. This paper reports on the design of EMVAP and its evaluation on several field databases that demonstrate that EMVAP produces a suitably modest overestimation of design concentrations. We also provide an example of an EMVAP application that involves a case in which a new emission limitation needs to be considered for a hypothetical emission unit that has infrequent higher-than-normal SO₂ emissions.

ImplicationsEmissions of pollutants from combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup and shutdown. While monitoring will automatically reflect this variability on measured concentrations, dispersion modeling is typically conducted with a single peak emission rate assumed to occur continuously. To realistically account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, the authors have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates.     

NO2 and SO2dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area,Thailand

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO₂ and SO₂ was conducted using the AERMOD model. The area-specific emission inventories of NO_x and SO₂ were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was found, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration over four selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations for each individual area, respectively. For AC-NO₂, on-road mobile emissions were found to be the largest contributor in the two residential areas (36–38% of total AC-NO₂), while petrochemical-industry emissions play the most important role in the two industrialized areas (34–51%). For AR-NO₂, biomass burning has the most influence in all impacted areas (>90%) except for one residential area where on-road mobile is the largest (75%). For AC-SO₂, the petrochemical industry contributes most in all impacted areas (38–56%). For AR-SO₂, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group when managing air quality for the MA.

Implications: Effective air quality management in Map Ta Phut Industrial Area, Thailand requires better understanding of how emissions from various sources contribute to the degradation of ambient air quality. Based on the dispersion study here, petrochemical industry was generally identified as the major contributor to ambient NO₂ and SO₂. By accounting for all stack and non-stack sources, on-road mobile emissions were found to be important in some particular areas.     

Mesoscale modeling of wintertime particulate matter episodes in eastern Washington, USA

The Spokane, Washington area is classified as a non-attainment area for the 24-h PM₁₀ standard due to a history of high particulate matter concentrations. A Eulerian regional air quality model (CALMET/CALGRID) has been used to characterize the emission, transport and dispersion of PM₁₀ and PM_2.5 in Spokane. Observations from a residential site (Rockwood, RW) and an industrial site (Crown Zellerbach, CZ), spanning July 1994–August 1996 were used to evaluate the current emission inventory. Two major tasks were devised to conduct the objectives of this investigation. First, a simple and efficient urban dispersion model (WYNDValley) was used to simulate important episodes characterized by the highest PM₁₀ and PM_2.5 concentrations. The selected episodes included four days with wet conditions for which no roads would have been emitting and seven days with dry conditions for which roads would emit. In the second step, a single road-emitting event was selected from the previous predicted results for further analysis using the Eulerian regional air quality model to examine the emission inventory. The urban and regional models predicted the observed concentration distributions reasonably well for the source emissions inventoried in Spokane. The mass concentrations of PM₁₀ were well predicted for the roads emitting case examined by both models indicating that the emission inventory based primarily upon area sources including roads is reasonably well characterized, at least at the RW site. The area sources around CZ are less well characterized, so that the PM₁₀ concentrations are underpredicted at CZ. The models appear unable to reach an equilibrium mass balance status at the beginning of the simulation, and the urban model seems unable to properly resolve the nocturnal boundary layer.     

Regional effects and efficiency of flue gas desulphurization in the Carpathian Basin

Although sulphur emissions (mainly as SO₂) have been continuously decreasing over the last 20 years in most western industrialized countries, localized SO₂ problems still exist in conjunction with strong local emission, meteorological, and topographical factors. In this study, the effect of supplementary installed flue gas desulphurization (FGD) units at high-capacity power plants on regional air pollution in the Carpathian Basin is investigated. The dispersion and accumulation of the SO₂ air pollutant are studied with the regional three-dimensional on-line atmosphere-chemistry model REMOTE. The changes in the SO₂ air pollution are investigated by parallel simulations in a case study, where the single modified parameter is the SO₂ emission rate. The results show that FGD units significantly reduce the horizontal and the vertical dispersion of the emitted SO₂, and its transboundary transport, too. Beside the SO₂ removal efficiency, the dispersion and accumulation also depend on the seasonal weather conditions. During winter, the dispersion and accumulation are higher than in other seasons. Due to this phenomenon, higher SO₂ removal efficiency is needed to guarantee similar air quality features like in the other seasons.     

Needed: A National R&D Effort To Develop Individual Air Pollution Monitor Instrumentation

The results from the regional air quality analysis for the Four Corners Study are discussed in this paper. This study was one of five regional studies conducted for the National Commission on Air Quality. Potential regional air quality impacts were evaluated through the year 1995 for alternative energy scenarios under current and alternative regulatory policies. The alternative regulatory policies include emission fees, technology standards, emission ceilings, and prevention of significant deterioration class elimination. The alternatives were compared in terms of their impacts on regional visibility and on the ambient concentrations of SO₂, SO₄, and primary fine particulates. The fate of the pollutants was estimated. The alternative regulatory policies were quite different with respect to their control of SO_X emissions and their impacts on regional visibility. Sources located outside of the study region were estimated to have a major impact on regional air quality within the study region.     

New indicator approaches for effective urban air quality management

Measurements of urban air quality at monitoring stations in developed countries have frequently involved the criteria gaseous pollutants, particulates, hazardous air pollutants, perceived air quality and relevant meteorological conditions. Large numbers of indicators have therefore been established to quantify emissions, concentrations and environmental and human health impacts of each of these groups of substances. To simplify the data for management, several indicators have been grouped together to form urban air quality indices but the weightings of individual variables is contentious. In industrialising and developing countries, data may be limited and traditional air pollutant indicators cannot often be constructed. The emphasis therefore has to be placed on the development of policy-relevant indicators, such as Response Indicators that reflect different policy principles for regulating air pollutant emissions. Indices that quantify the air quality management capabilities and capacities at the city level provide further useful decision-relevant tools. Four sets of indices, namely, 1. air quality measurement capacity, 2. data assessment and availability, 3. emissions estimates, and 4. management enabling capabilities, and a composite index to evaluate air quality management capability, were constructed and applied to 80 cities. The indices revealed that management capability varied widely between the cities. In some of the cities, existing national knowledge on urban air quality could have been more effectively used for management. It was concluded that for effective urban air quality management, a greater emphasis should be given, not just to monitoring and data capture programmes, but to the development of indicators and indices that empower decision-makers to initiate management response strategies. Over-reliance on restricted, predetermined sets of traditional air quality indicators should be avoided.     

Estimation of hydrogen sulfide emission rates at several wastewater treatment plants through experimental concentration measurements and dispersion modeling

The management and operation of wastewater treatment plants (WWTP) usually involve the release into the atmosphere of malodorous substances with the potential to reduce the quality of life of people living nearby. In this type of facility, anaerobic degradation processes contribute to the generation of hydrogen sulfide (H₂S), often at quite high concentrations; thus, the presence of this chemical compound in the atmosphere can be a good indicator of the occurrence and intensity of the olfactory impact in a specific area. The present paper describes the experimental and modelling work being carried out by CEAM-UMH in the surroundings of several wastewater treatment plants located in the Valencia Autonomous Community (Spain). This work has permitted the estimation of H₂S emission rates at different WWTPs under different environmental and operating conditions. Our methodological approach for analyzing and describing the most relevant aspects of the olfactory impact consisted of several experimental campaigns involving intensive field measurements using passive samplers in the vicinity of several WWTPs, in combination with numerical simulation results from a diagnostic dispersion model. A meteorological tower at each WWTP provided the input values for the dispersion code, ensuring a good fit of the advective component and therefore more confidence in the modelled concentration field in response to environmental conditions. Then, comparisons between simulated and experimental H₂S concentrations yielded estimates of the global emission rate for this substance at several WWTPs at different time periods. The results obtained show a certain degree of temporal and spatial (between-plant) variability (possibly due to both operational and environmental conditions). Nevertheless, and more importantly, the results show a high degree of uniformity in the estimates, which consistently stay within the same order of magnitude.

Implications: Estimating emissions to the atmosphere is usually considered a complex task, especially when such discharge comes from diffuse or uncontrolled sources. In any approach to air quality control, just from the point of view of increasing knowledge or as a management problem in order to reduce present levels of pollution, accurate estimation of emission rates is revealed as a fundamental step. Evaluation from an indirect method provides a useful methodology in such cases. Combination of dispersion modeling with experimental air concentration measurements permits one to obtain a first estimation of H₂S emission rates at several wastewater treatment plants. In a subsequent refinement of the process, the initial constant average emissions calculated were improved, leading to the formulation of a time-varying emission model, as a function of environmental quantities.     

Evaluation of low wind modeling approaches for two tall-stack databases

The performance of the AERMOD air dispersion model under low wind speed conditions, especially for applications with only one level of meteorological data and no direct turbulence measurements or vertical temperature gradient observations, is the focus of this study. The analysis documented in this paper addresses evaluations for low wind conditions involving tall stack releases for which multiple years of concurrent emissions, meteorological data, and monitoring data are available. AERMOD was tested on two field-study databases involving several SO₂ monitors and hourly emissions data that had sub-hourly meteorological data (e.g., 10-min averages) available using several technical options: default mode, with various low wind speed beta options, and using the available sub-hourly meteorological data. These field study databases included (1) Mercer County, a North Dakota database featuring five SO₂ monitors within 10 km of the Dakota Gasification Company’s plant and the Antelope Valley Station power plant in an area of both flat and elevated terrain, and (2) a flat-terrain setting database with four SO₂ monitors within 6 km of the Gibson Generating Station in southwest Indiana. Both sites featured regionally representative 10-m meteorological databases, with no significant terrain obstacles between the meteorological site and the emission sources. The low wind beta options show improvement in model performance helping to reduce some of the overprediction biases currently present in AERMOD when run with regulatory default options. The overall findings with the low wind speed testing on these tall stack field-study databases indicate that AERMOD low wind speed options have a minor effect for flat terrain locations, but can have a significant effect for elevated terrain locations. The performance of AERMOD using low wind speed options leads to improved consistency of meteorological conditions associated with the highest observed and predicted concentration events. The available sub-hourly modeling results using the Sub-Hourly AERMOD Run Procedure (SHARP) are relatively unbiased and show that this alternative approach should be seriously considered to address situations dominated by low-wind meander conditions.

Implications: AERMOD was evaluated with two tall stack databases (in North Dakota and Indiana) in areas of both flat and elevated terrain. AERMOD cases included the regulatory default mode, low wind speed beta options, and use of the Sub-Hourly AERMOD Run Procedure (SHARP). The low wind beta options show improvement in model performance (especially in higher terrain areas), helping to reduce some of the overprediction biases currently present in regulatory default AERMOD. The SHARP results are relatively unbiased and show that this approach should be seriously considered to address situations dominated by low-wind meander conditions.     

Correlating Emissions with Time and Temperature to Predict Worst-Case Emissions from Open Liquid Area Sources

Abstract

The two primary factors influencing ambient air pollutant concentrations are emission rate and dispersion rate. Gaussian dispersion modeling studies for odors, and often other air pollutants, vary dispersion rates using hourly meteorological data. However, emission rates are typically held constant, based on one measured value. Using constant emission rates can be especially inaccurate for open liquid area sources, like wastewater treatment plant units, which have greater emissions during warmer weather, when volatilization and biological activity increase. If emission rates for a wastewater odor study are measured on a cooler day and input directly into a dispersion model as constant values, odor impact will likely be underestimated. Unfortunately, because of project schedules, not all emissions sampling from open liquid area sources can be conducted under worst-case summertime conditions. To address this problem, this paper presents a method of varying emission rates based on temperature and time of the day to predict worst-case emissions. Emissions are varied as a linear function of temperature, according to Henry’s law, and a tenth order polynomial function of time. Equation coefficients are developed for a specific area source using concentration and temperature measurements, captured over a multiday period using a data-logging monitor. As a test case, time/temperature concentration correlation coefficients were estimated from field measurements of hydrogen sulfide (H₂S) at the Rowlett Creek Wastewater Treatment Plant in Garland, TX. The correlations were then used to scale a flux chamber emission rate measurement according to hourly readings of time and temperature, to create an hourly emission rate file for input to the dispersion model ISCST3. ISCST3 was then used to predict hourly atmospheric concentrations of H₂S. With emission rates varying hourly, ISCST3 predicted 384 acres of odor impact, compared with 103 acres for constant emissions. Because field sampling had been conducted on relatively cool days (85–90 °F), the constant emission rate underestimated odor impact significantly (by 73%).     

Operational air pollution modelling in the UK—Street canyon applications and challenges

Local air quality management requires the use of screening and advanced modelling tools that are able to predict roadside pollution levels under a variety of meteorological and traffic conditions. So far, more than 200 air pollution hotspots have been identified by local authorities in the UK, many of them associated with NO₂ and/or PM₁₀ exceedences in heavily trafficked urban streets that may be classified as street canyons or canyon intersections. This is due to the increased traffic-related emissions and reduced natural ventilation in such streets. Specialised dispersion models and empirical adjustment factors have been commonly used to account for the entrapment of pollutants in street canyons. However, most of the available operational tools have been validated using experimental datasets from relatively deep canyons (H/W⩾1) from continental Europe. The particular characteristics of low-rise street canyons (H/W<1), which are a typical feature of urban/sub-urban areas in the UK, have been rarely taken into account.The main objective of this study is to review current practice and evaluate three widely used regulatory dispersion models, WinOSPM, ADMS-Urban 2.0 and AEOLIUS Full. The model evaluation relied on two comprehensive datasets, which included CO, PM₁₀ and NO_x measurements, traffic information and relevant meteorological data from two busy street canyons in Birmingham and London for a 1-year period. The performance of the selected models was tested for different times of the day/days of the week and varying wind conditions. Furthermore, the ability of the models to reproduce roadside NO₂/NO_x concentration ratios using simplified chemistry schemes was evaluated for one of the sites. Finally, advantages and limitations of the current regulatory street canyon modelling practice in the UK, as well as needs for future research, have been identified and discussed.     

Assessment of 2010 air quality in two Alpine valleys from modelling: Weather type and emission scenarios

Alpine valleys are sensitive to anthropogenic emissions. Local atmospheric dynamics are a key factor that may lead to an accumulation of pollutants in the bottom of the Chamonix and Maurienne valleys. Assessment of 2010 pollutant concentrations variability needs to take these specificities into account. A meteorological data classification is combined with different emission scenarios in order to run an air quality model. Using simulations of representative scenarios rather than complete years allows for a fine spatial and temporal representation of local atmospheric dynamics and gives access to detailed chemical breakdowns. Results demonstrate the variability of primary and secondary species due to emissions and the predominance of local effects on pollutant concentrations.     

Reduction of atmospheric emissions due to switching from fuel oil to natural gas at a power plant in a critical area in Central Mexico

ABSTRACT

A case study was conducted to evaluate the SO₂ emission reduction in a power plant in Central Mexico, as a result of the shifting of fuel oil to natural gas. Emissions of criteria pollutants, greenhouse gases, organic and inorganic toxics were estimated based on a 2010 report of hourly fuel oil consumption at the “Francisco Pérez Ríos” power plant in Tula, Mexico. For SO₂, the dispersion of these emissions was assessed with the CALPUFF dispersion model. Emissions reductions of > 99% for SO₂, PM and Pb, as well as reductions >50% for organic and inorganic toxics were observed when simulating the use of natural gas. Maximum annual (993 µg/m³) and monthly average SO₂ concentrations were simulated during the cold-dry period (152–1063 µg/m³), and warm-dry period (239–432 µg/m³). Dispersion model results and those from Mexico City’s air quality forecasting system showed that SO₂ emissions from the power plant affect the north of Mexico City in the cold-dry period. The evaluation of model estimates with 24 hr SO₂ measured concentrations at Tepeji del Rio suggests that the combination of observations and dispersion models are useful in assessing the reduction of SO₂ emissions due to shifting in fuels. Being SO₂ a major precursor of acid rain, high transported sulfate concentrations are of concern and low pH values have been reported in the south of Mexico City, indicating that secondary SO₂ products emitted in the power plant can be transported to Mexico City under specific atmospheric conditions.

Implications: Although the surroundings of a power plant located north of Mexico City receives most of the direct SO₂ impact from fuel oil emissions, the plume is dispersed and advected to the Mexico City metropolitan area, where its secondary products may cause acid rain. The use of cleaner fuels may assure significant SO₂ reductions in the plant emissions and consequent acid rain presence in nearby populated cities and should be compulsory in critical areas to comply with annual emission limits and health standards.     

Analysis of Air Quality Observations with the Aid of the Source-Receptor Relationship Approach

Abstract

In this study, an attempt was made to analyze time series of air quality measurements (O₃, SO₂, SO₄ ^2?NO_x) conducted at a remote place in the eastern Mediterranean (Finokalia at Crete Island in 1999) to obtain concrete information on potential contributions from emission sources. For the definition of a source-receptor relationship, advanced meteorological and dispersion models appropriate to identify “areas of influence” have been used. The model tools used are the Regional Atmospheric Modeling System and the Lagrangian-type particle dispersion model (forward and backward in time), with capabilities to derive influence functions and definition of “areas of influence.” When high levels of pollutants have been measured at the remote location of Finokalia, particles are released from this location (receptor) and traced backward in time. The influence function derived from particle distributions characterizes dispersion conditions in the atmosphere and also provides information on potential contributions from emission sources within the modeling domain to this high concentration. As was shown in the simulation results, the experimental site of Finokalia in Crete is influenced during the selected case studies, primarily by pollutants emitted from the urban conglomerate of Athens. Secondarily, it is influenced by polluted air masses arriving from Italy and/or the Black Sea Region. For some specific cases, air pollutants monitored at Finokalia were possibly related to war activities in the West Balkan Region (Kosovo).     

Analysis of climatological and air quality observations from Greater Athens Area

In this paper, the climatological and air quality observations obtained for the periods 1974–1990 and 1983–1990, respectively, in the Greater Athens Area, are analyzed. During this period, 80 air pollution episodes, which lasted 210 d in total, were detected. The analysis of the observations allows the interpretation of air quality characteristics in terms of the climatological and meteorological factors. The importance of some characteristic indices for air pollutant dispersion conditions, such as mixing height, ventilation coefficient, temperature at 850 hPa, and temperature inversions, is discussed. The results show that the air quality in the Athens Basin is strongly affected by the meteorological conditions, especially those which are in favor of local circulations. The worst air pollution episodes are associated with anticyclonic conditions and/or advection of warm air masses.     

A model for the maximum credible hourly impact on any ground receptor from point sources with thermal plume rise

A pollutant dispersion model is developed, allowing fast evaluation of the maximum credible 1-h average concentration on any given ground-level receptor, along with the corresponding critical meteorological conditions (wind speed and stability class) for stacks with buoyant plumes in urban or rural areas. Site-specific meteorological data are not required, as the computed concentrations are maximized against all credible combinations of wind speed, stability class, and mixing height. The analysis is based on the dispersion relations of Pasquill-Gifford and Briggs for rural and urban settings, respectively, the buoyancy induced dispersion correlation of Pasquill, the wind profile exponent values suggested by Irwin, the buoyant plume rise relations of Briggs, as well as the Benkley and Schulman's model for the minimum mixing heights. The model is particularly suited for air pollution management studies, as it allows fast screening of the maximum impact on any selected receptor and evaluation of the ways to have this impact reduced. It is also suited for regulatory purposes, as it can be used to define the minimum stack size requirements for a given source as a function of the exit gas volume and temperature, the pollutant emission rates and their hourly concentration standards, as well as the source location relative to sensitive receptors.