超声波技术降解水中氯代有机物的研究进展

介绍了超声波技术的基本原理,概述了超声波和各种超声联用（超声波与紫外光、过氧化氢、臭氧、Fenton试剂等联用）技术降解氯代有机物的效果和影响因素,总结了氯代有机物降解机理与动力学的研究进展,并在此基础上提出了今后超声波及其联用技术降解水中氯代有机物的研究方向。     

超声波处理石化厂剩余活性污泥

采用超声波处理石化污水处理厂的剩余活性污泥。介绍了超声波对污泥的作用机理，初步研究了超声波处理污泥的影响因素。大功率超声波可以降解生物污泥，释放出其中的有机物。小功率超声波能够改善污泥的膨胀特性、提高污泥沉淀特性和脱水能力、降低污泥的含水率，达到减量的目的。经超声波处理并简单过滤的污泥滤液，COD达到4200mg／L左右，污泥含水率由94％降至85％左右。     

超声波处理剩余活性污泥促进厌氧消化

用超声波处理剩余活性污泥(简称污泥),考察了污泥絮体结构、污泥中溶解性化学需氧量(SCOD)的变化规律及超声波处理对污泥厌氧消化的影响。实验结果表明,声强大于1 040W/m2时,用超声波处理污泥30m in以上,污泥絮体被打碎,污泥絮体结构遭到严重破坏,污泥中SCOD迅速增加,加速了污泥中有机质的水解反应;声强为2 000W/m2时,用超声波处理污泥60m in,中温((37±1)℃)厌氧消化10d,COD去除率为41%;厌氧消化25d的总产气量比未经超声波处理的污泥总产气量提高了53%;将发酵罐容积放大10倍,经超声波处理的污泥25d累积的总产气量比未经超声波处理的污泥总产气量提高了约25%。     

起声波法减少污泥量

德国Fraunhofer陶瓷技术研究院与两个工业合作伙伴共同开发出一种超声波污泥处理法,可减少污泥量约20%,增加沼气产量20%～25%,并在德国的Detmold建成一套示范装置。污泥连续进入有7个声极的超声波反应器。每个声极在12kW产生20kHz的超声波。这种超声波将细菌团粒及其他固体打破,使污泥易于脱水,使分解有机物的酶放出,增加沼气的产量,并使脱水用的絮凝剂用量减少约25%。可用这种超声波反应器改造现有的污泥处理装置,1～2年就可收回投资起声波法减少污泥量     

高分子絮凝剂对污泥脱水性能的影响

使用活性污泥法处理废水会产生大量剩余污泥,给污泥的处理和处置带来很大麻烦.许多方法可用于减少剩余污泥量,如消化和脱水.化学药剂可用于提高污泥的脱水性能.介绍了污泥脱水性能的表达方式及聚电解质提高污泥脱水性能的原理,讨论了聚电解质提高污泥脱水性能的相关影响因素.     

废硅藻土回收应用于污泥深度脱水处理

硅藻土作为助滤剂被大量使用,用后废弃硅藻土液容易变质发臭并严重污染环境,桂林市某啤酒生产企业对废硅藻土液进行回收,并作为调理剂应用到卧式弹簧压榨污泥深度脱水处理系统中,增强污泥絮凝调理效果,促进污泥更好地压滤和压榨脱水,既解决废硅藻土难处理问题,又达到以废、治废变废为宝和降低污泥脱水成本的目的。     

高频超声波降解4-氯酚的反应机理及试验研究

探讨了高频超声波（1.7MHz)降解4-氯酚的反应过程和反应机理，研究了高频超声波降解4-氯酚的效果及4-氯酚的初始浓度，高级氧化方法（AOPs)等因素对降解效果的影响。试验结果表明，高频超声波降解4-氯酚为一级反应，超声波空化效应在降解过程中起主导作用。超声波与其他氧化方法联用可大大提高降解效率。具有良好的工业应用前景。     

污泥热水解技术研究进展

热水解可以改善污泥的生物降解性能和脱水性能,提高后续厌氧消化系统中有机物的去除率。本文阐述了热水解对污泥物理特性主要包括流变特性和脱水行为的影响;分析了热水解对污泥中氨氮浓度及对厌氧消化的作用;同时介绍了热水解技术对整个污泥处理系统能量需求的影响。指出：热水解改善了污泥的厌氧消化性能,提高了沼气等再生资源的产量,且厌氧消化产生的沼气量与热水解技术所需的能量基本平衡。     

污泥陶粒的烧制与改性研究进展

城市污泥中含有大量硅、铝、铁等无机物质和部分有机物质,在添加辅料后可烧制生成强度高、吸附性能优良、耐腐蚀的轻质陶粒,因此近年来烧制污泥陶粒受到了广泛关注。在陶粒的烧制过程中,由于污泥成分不同,需加入不同比例的辅料以及设置不同的烧制条件来保证污泥陶粒具备良好的物理性能。传统的陶粒与活性炭相比,吸附性能存在一定差距,因此考虑将陶粒从改变内部结构、酸碱浸泡、引入其他离子等方面进行改性,改性后的污泥陶粒对特定污染物的吸附性得到显著提高。     

炼油废水污泥脱水工艺条件的优化

采用化学除油降黏—污泥调理—离心脱水工艺处理某炼油厂废水处理系统的混合污泥,并对工艺条件进行优化。实验结果表明,最佳的工艺条件为:化学除油降黏阶段处理体系的pH=4,反应温度35℃,H2O2加入量2 g/L,m(H2O2)∶m(Fe2+)=4,反应时间60 min;污泥调理反应阶段的CaO加入量7.0 g/L;离心脱水阶段在分离因数为1 558时脱水5 min。在此条件下,得到的泥饼的含水率为70.0%~75.0%(w),含油率小于2%(w),污泥比阻约为3.0×107 s2/g。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.