从废甲醇合成催化剂中回收铜锌

将废RK-05甲醇合成催化剂经过煅烧、浸取、精制等工序回收其中的铜和锌。经正交实验得到煅烧废催化剂的最优工艺参数为:废催化剂筛目100目,煅烧温度950℃,煅烧时间60 min。最佳浸取工艺条件为:废催化剂加入量约4 g/L,浸取温度75℃,浸取剂用量与理论用量体积比2.0~3.0,浸取剂浓度4.0 mol/L,浸取时间10min。精制工序制备CuO的最佳工艺条件为:锌粒与滤渣质量比为1.00,反应时间3 h,煅烧温度450℃,煅烧时间4 h。制备ZnO的最佳工艺条件为:煅烧温度800℃,煅烧时间60 min。回收的产品CuO纯度为99.1%,满足GB/T674—2003《化学试剂粉状氧化铜》中优级品的标准。回收的产品ZnO纯度为99.6%,满足GB/T3185—1992《氧化锌(间接法)》中一级品的标准。     

从硬质合金处理渣中回收氧化钴

根据硫酸钠熔炼法处理废合金所得钴渣组成特点,通过氧化焙烧、酸分解、水解除杂、沉钴和煅烧等工序制取氧化钴.焙烧最佳工艺条件为:NaNO3用量为钴渣量的0.8倍,焙烧温度750 ℃,时间2.5 h.盐酸分解、喷淋水解除铁、草酸铵沉钴和煅烧阶段钴的回收率(%)分别为97.5、96.6、99.5和99.0,使Co、Ta的回收率分别达到92.78%和85%.     

硫酸生产中废钒催化剂回收工艺研究

采用H2SO4浸取、NH4HSO3还原、NH4NO3氧化、KOH精制的方法回收废钒催化剂中的V2O5。实验结果表明,还原反应的最佳条件为：n（NH4HSO3）／n（V2O5）=1．10,还原反应温度90℃,还原反应时间2．0h。氧化反应的最佳条件为：n（KOH）／n（VO^＋）=1．10,氧化反应温度60℃,液固比8,氧化反应时间60min。该方法V2O5回收率达90．3％以上,V2O5纯度达82％以上。     

废磷酸系刻蚀液制备电池级磷酸铁

以废磷酸系刻蚀液为原料、铁粉为铁源、H₂O₂为氧化剂，采用氧化沉淀法一步合成结晶态FePO₄。考察了铁磷摩尔比、反应温度、H₂O₂投加量、pH、煅烧温度对FePO₄制备的影响，利用XRD、SEM等手段表征了FePO₄的形貌和晶体结构。实验结果表明，在铁磷摩尔比1.000、反应温度90℃、n(H₂O₂)∶n(H₃PO₄)1.05、pH2.2～2.4、煅烧温度600℃的最佳工艺条件下，废刻蚀液中PO₄^3-、NO₃^-、醋酸的去除率分别为87.70%、87.42%和90.25%,FePO₄的产品转化率为77.99%，所制备的FePO₄晶体结构规则，结晶度高，粒径为2.0～6.0μm，铁、磷质量分数和杂质元素含量等指标均能满足《...     

脉冲等离子体催化还原脱硫催化剂的活性研究

在不同温度下煅烧以沉淀方法解得的La(OH)3，研究锻烧产物及其催化活性，发现LaOOH在380－500℃范围内生成。此研究结对降低还原脱硫的反应温度有重要意义，单纯的La（OH）3粉末催化结果不明显，用γ-Al2O3作载体，采用浸泡法制得的Ce-La/AL2O3催化剂脱硫效果极佳。     

酸洗废液制备高纯氧化铁红

以钢板酸洗废液为原料,采用铁粉预处理、除杂、合成、水洗、干燥、煅烧等工序制备高纯氧化铁红.最佳工艺条件为:预处理温度80℃,预处理时间3h,铁粉加入量为理论值的1.5倍;除杂温度65 ℃,聚丙烯酰胺加入量60 mg/L;米用将FeC12溶液和饱和NH4HCO3溶液同时滴加入反应器的方式进行沉淀反应;煅烧温度800℃.在此工艺条件下处理酸洗废液,可制得纯度为99.3％的高纯氧化铁红.     

用Co3O4催化剂光催化氧化活性染料

以沉淀一热解法制备了纳米级Co3O4催化剂,并用X射线衍射仪、红外光谱仪对Co3O4催化剂进行了表征。以300W高压汞灯为光源,研究了Co3O4催化剂对不同活性染料的光催化氧化活性。实验结果表明：在活性染料质量浓度为20mg／L、250mL染料溶液中Co3O4催化剂加入量为150mg、反应2h的条件下,Co3O4催化剂对B—GFF黑、B—RN蓝、K—NR艳蓝3种活性染料溶液的脱色率分别为95％,87％,77％;适当加入酸或碱有利于提高处理效率,反应后染料溶液的pH为7．12～8．37,染料溶液初始pH为10．00时的脱色率最高为100％;Co3O4催化剂具有一定的再利用价值。     

酸浸—萃取—沉淀法回收废锂离子电池中的钴

采用酸浸—萃取—沉淀法回收废锂离子电池中的钴。实验结果表明:废锂离子电池在600℃下煅烧5 h可将正极材料上的有机黏结剂与正极活性物质分离;正极活性物质在Na OH溶液浓度为2.0 mol/L、n(Na OH)∶n(铝)=2.5、碱浸温度为20℃的条件下碱浸反应1 h后,铝浸出率达99.7%;已除铝的正极活性物质在硫酸浓度为2.5 mol/L、H_2O_2质量浓度为7.25 g/L、液固比为10、酸浸温度为85℃的条件下酸浸反应120 min,钴浸出率高达98.0%;酸浸液在p H为3.5、萃取剂P507与Cyanex272体积比为1∶1的条件下,经2级萃取,钴萃取率为95.5%;采用H_2SO_4溶液反萃后在硫化钠质量浓度为8 g/L、反萃液p H为4的条件下沉淀反应10 min,钴沉淀率达99.9%。     

Fe_2O_3/膨润土微波诱导氧化处理染料废水

以膨润土为载体,采用直接沉淀法制备了Fe2O3/膨润土负载型催化剂。制备催化剂的最佳工艺条件:硝酸铁质量浓度为8.08g/L,硝酸铁与膨润土质量比为1.0,焙烧温度为350℃,焙烧时间为3h。用Fe2O3/膨润土负载型催化剂微波诱导氧化处理50mL质量浓度为50mg/L的模拟活性嫩黄废水的最佳工艺条件:催化剂加入量为0.5g,微波功率为900W,微波作用时间为5min。在此条件下模拟活性嫩黄废水脱色率达96.40%。微波诱导氧化处理模拟活性嫩黄废水的反应符合一级反应动力学方程。     

含有机硫废碱液的综合利用

采用ＣｕＯ沉淀剂与含有机硫废碱液进行固液反应,经过滤回收ＮａＯＨ,碱液中的有机硫由滤渣吸附除去,灼烧滤渣得到的ＣｕＯ可循环使用,并可得到副产品Ｎａ２Ｓ２Ｏ５。最佳的试验条件为;Ｃｕ：Ｓ＝１．５６;１,反应温度２０－３０℃,反应时间３０ｍｉｎ,滤渣灼烧温度９００－９５０℃,灼烧时间３０ｍｉｎ。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Methane generation from corncobs treated with xylanolytic consortia

Consortia were developed for the treatment of corncobs for use as a feedstock in a biogas fermentor. The treatment of corncobs with xylanolytic consortia enhanced the production of methane and biogas. All five consortia developed produced the maximum biogas and methane at a 6% loading rate and 20 days hydraulic retention time (HRT). The maximum biogas yield of 0.59m³/kg volatile solids (VS) with a methane content of 62% was produced with the KK-10 consortium. This was apparently due to a maximum hemicellulose degradation of 88%.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

Preparation and Biodegradation of Starch/Polycaprolactone Films

Starch granules were modified with trisodium trimetaphosphate (TSTP) and characterized by P³¹-NMR, FTIR and DSC. Seventy-micron films were prepared from modified starch and polycaprolactone blends by solvent casting technique. Three different types of films—PCL (100% polycaprolactone), MOD-ST/PCL (50% modified starch and 50% polycaprolactone blend) and NONMOD-ST/PCL (50% nonmodified starch and 50% polycaprolactone blends)—were prepared, and their thermal, mechanical, and morphologic properties were investigated to show the increased performance of PCL with the addition of starch and also the effect of modification. It was observed that with the addition of starch the Young's modulus of polycaprolactone was increased and became less ductile, whereas tensile strength and elongation at break values decreased. Biodegradation of these films was inspected under different aerobic environments with the presence of Pseudomonas putida, activated sludge, and compost. It was observed that whereas P. putida had almost no effect on degradation during 90 days, with the presence of activated sludge, considerable deformation of films was observed even in the first 7 days of degradation. In a compost environment, degradation was even faster, and all polymer films were broken into pieces within first 7 days of degradation and no film remained after 15 days.