改进铁氧体共沉淀法去除污泥浸出液中的铜锌

采用改进铁氧体共沉淀法,用石灰乳溶液作中和剂,从污泥浸出液中去除铜、锌。实验结果表明,在混合液．pH为8．9、反应温度为室温、反应时间为1h、FeCl3和FeSO4初始浓度分别为0．1068mol／L和0．0534mol／L、n（Fe^3＋）：[n（Cu^2＋）＋n（Zn^2＋）]=10的最佳工艺条件下,浸出液中铜去除率为94．5％,锌去除率为98．0％。     

镰刀菌HJ01对苯酚的降解性能

为了研究真菌对苯酚的降解能力,采用本实验室分离的一株镰刀菌HJ01,考察了外加碳源、降解体系初始pH、温度对HJ01菌体生长量和苯酚降解效果的影响,初步探讨了镰刀菌降解苯酚的动力学与机理。实验结果表明,该菌能以苯酚为惟一碳源生长,添加适量的蔗糖可促进HJ01菌体的生长及苯酚的降解。在蔗糖加入量为3g／L、降解体系初始pH为6．0、温度为30℃的最佳条件下,经HJ01菌处理4d后的质量浓度为420mg／L苯酚废水中的苯酚完全降解。镰刀菌的生长和苯酚降解动力学符合Andrews模型。     

链霉菌(Streptomyces sp.)对吡啶的降解特性

从焦化废水的活性污泥中分离出对溶液中吡啶具有降解效果的链霉菌（Streptomyces sp．）,考察了吡啶初始质量浓度、初始pH、降解温度、振荡速度等对吡啶降解效果的影响,初步探讨了该菌降解吡啶的动力学与机理。实验结果表明,该菌对吡啶有很强的耐受力,能以吡啶为惟一碳源和氮源生长。链霉菌在初始pH=8、降解温度30℃、振荡速度100r／min的条件下培养7d后,吡啶的质量浓度从250mg/L降至6．6mg/L,吡啶降解率达97．4％。该菌对吡啶的降解反应符合一级动力学方程,初始质量浓度为100mg／L时的吡啶降解速率常数为0．4011d^-1。紫外一可见光谱分析表明,吡啶经该菌降解后的特征环被破坏。     

污泥活性炭的制备及其对溶液中Cr6+的吸附

以城市污水厂剩余污泥为原料,采用ZnCl2作活化剂,热解制备污泥活性炭。实验结果表明,制备污泥活性炭的最佳条件热解温度为550℃,ZnCl2溶液浓度为3mol／L,ZnCl2溶液体积与污泥质量比（mL／g）为2．5：1,热解时间为25min。用所制备的污泥活性炭吸附溶液中的Cr6＋最佳吸附条件为：吸附时间90min,Cr6＋初始质量浓度50mg／L,污泥活性炭加入量0．2g,溶液pH2,在此条件下,Cr6＋去除率达99．9％。污泥活性炭对溶液中Cr6＋的吸附等温线属于I型,等温吸附方程可用Langmuir模型和Freundlich模型来拟合。     

酸析-Fenton试剂氧化-混凝法处理制浆废水

用酸析-Fenton试剂氧化-混凝法对自偶氧化清洁制浆废水进行预处理,考察了各种因素对处理效果的影响。最佳处理条件：酸析时的废水pH为3．0;酸析后上层清液无需调节pH,加水稀释至COD为2000mg／L后进行Fenton试剂氧化,H2O2加入量为84．56mmol／L,FeS04加入量为8．44mmol／L,反应时间60min;混凝时Ca（OH）：加入量为2g／L。最终出水的COD为577．20mg／L（COD去除率为71．14％）,色度为36倍,pH为8．60。     

镰刀菌HJ01对对氯苯酚的降解特性

采用实验室分离的一株镰刀菌HJ01,以对氯苯酚(4-CP)为降解底物,以蔗糖为外加碳源,考察了蔗糖质量浓度、降解温度、初始pH对4-CP降解效果的影响,初步探讨了镰刀菌HJ01对4-CP的降解动力学和降解机理.实验结果表明:该菌株能以4-CP为惟一碳源和能源生长;在外加蔗糖为碳源,蔗糖质量浓度为3 g/L、降解温度为30℃、初始pH为8的条件下,50 mg/L4-CP能在6 d内被完全降解.以4-CP为惟一碳源和外加蔗糖下的降解动力学分别符合Haldane模型和一级动力学方程.     

甲苯降解菌的分离、鉴定及其对甲苯的降解特性

从重庆钢铁集团焦化厂脱酚池车间污泥中分离纯化得到一株能以甲苯为惟一碳源和能源的革兰氏阴性菌。根据生理生化实验结果、菌落特征、菌体形态,初步鉴定为假单孢菌属。菌株的最佳生长条件为：pH7、温度35℃、加入量100mL培养基中加入60μL甲苯、接种量5．0％。考察了菌株对甲苯的降解特性,在甲苯质量浓度为150mg/L时,比降解速率达到0．211h^-1。     

阳离子聚丙烯酰胺絮凝剂的制备及其絮凝性能

研究了丙烯酰胺（AM）与丙烯酰氧乙基三甲皋氯化铵共聚反应制备阳离子聚丙烯酰胺絮凝剂的工艺。实验结果表明,最佳聚合条件：pH6．0、（NH4）2S2O8和CH3NaO3S·2H2O总质量分数0．0125％、（NH4）：S2O8与CH3NaO3S·2H2O质量比1．0、偶氮类化合物质量分数0．0125％、单体质量分数（AM和阳离子单体总质量占整个反应体系的质量分数）35％、阳离子度（阳离子单体占AM和阳离子单体之和的质量分数）30％、反应温度25℃。在最佳条件下,所得阳离子聚丙烯酰胺絮凝剂的特性黏数为13．8535dl／g,在其加入量为0．027％的条件下处理污泥,上层清液透光率达99．6％,污泥脱水率达90．5％。并用红外光谱对阳离子聚丙烯酰胺的结构进行了表征。     

用Co3O4催化剂光催化氧化活性染料

以沉淀一热解法制备了纳米级Co3O4催化剂,并用X射线衍射仪、红外光谱仪对Co3O4催化剂进行了表征。以300W高压汞灯为光源,研究了Co3O4催化剂对不同活性染料的光催化氧化活性。实验结果表明：在活性染料质量浓度为20mg／L、250mL染料溶液中Co3O4催化剂加入量为150mg、反应2h的条件下,Co3O4催化剂对B—GFF黑、B—RN蓝、K—NR艳蓝3种活性染料溶液的脱色率分别为95％,87％,77％;适当加入酸或碱有利于提高处理效率,反应后染料溶液的pH为7．12～8．37,染料溶液初始pH为10．00时的脱色率最高为100％;Co3O4催化剂具有一定的再利用价值。     

活性污泥工艺中加代谢解偶联剂降低污泥产率的研究

2,4,5-三氯苯酚（TCP）作为代谢解偶联剂投加到连续曝气分批培养的活性污泥工艺中,在30d的运行期间,TCP质量浓度为2．0mg／L和4．0mg／L的污泥产率分别比对照反应下降了约25％和50％,而基质的去除率及出水的氮和磷浓度均未受很大影响,污泥的沉降性能也未受影响。镜检发现,30d运行后对照实验的反应器中仍有丝状菌,而投加TCP反应器的污泥中几乎未发现丝状菌的存在。应用TCP作为代谢解偶联剂投加到活性污泥工艺中可减少剩余污泥的产量。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.