首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
零价铁、镍-铁和铜-铁双金属对四氯乙烯的脱氯性能研究   总被引:7,自引:2,他引:5  
研究了零价铁、镍-铁和铜-铁双金属对四氯乙烯(PCE)的还原性脱氯性能。实验结果表明,零价铁、镍-铁和铜-铁双金属对PCE的脱氯反应符合准一级反应动力学方程;双金属对P(=E的脱氯反应速率高于零价铁,镍-铁双金属对PCE的脱氯反应速率常数是零价铁的2.486倍;镍-铁和铜-铁双金属可使PCE完全脱氯,零价铁在对PCE脱氯的过程中产生一定量的三氯乙烯;增加金属质量,可提高PCE的脱氯反应速率;金属颗粒越小,越有利于PCE脱氯反应。  相似文献   

2.
肖骁  肖松文 《化工环保》2006,26(5):362-365
以锌粉为还原剂进行了聚氯乙烯(PVC)的机械化学还原脱氯(简称脱氯)探索研究,考察了球磨转速、球料比(磨球与试样的质量比)、锌粉与PVC质量比等对脱氯率的影响,并对脱氯产物进行了X射线衍射、红外光谱等分析。实验结果表明,最佳工艺条件为球料比33、球磨转速528r/min、锌粉与PVC质量比9;产物中未形成结晶性氯化锌,且锌粉被氧化成ZnO;行星球磨比搅拌球磨对PVC的脱氯效果好,球磨时间超过3h,PVC的脱氯率可接近100%。  相似文献   

3.
刘光永  郭红宇 《化工环保》1997,17(4):195-200
在微反应色谱和熔盐换热固定床反应装置上,用Pt/Al2O3催化剂进行多氯苯加氢脱氯反应的试验研究,考察了温度,液体空速,压力,氢料摩尔反应条件对多氯苯催化氢解脱氯的影响,结果表明,在适宜反应条件下,多氯苯脱氯率为50%,氯苯和二氯苯收率在40%以上。  相似文献   

4.
利用盐酸酸洗废液制备聚合硅酸氯化铝铁(PSAFC),并用PSAFC处理造纸脱墨废水,考察了各种因素对絮凝效果的影响。实验结果表明:在废水pH为6、PSAFC加入量为240mg/L、搅拌转速为150r/min、搅拌时间为2min,静置时间为25min的条件下,COD、浊度、色度的去除率分别为87.2%,99.2%,94.5%;PSAFC的絮凝效果明显好于市售的聚合氯化铝和聚合氯化铁.  相似文献   

5.
苯基周位酸生产废水处理试验研究   总被引:7,自引:0,他引:7  
采用CHA-111大孔吸附树脂对苯基周位酸生产过程排放的汽提苯胺盐析废水和苯基周位酸酸析母液进行处理试验,效果良好。汽提苯胺盐析废水苯胺质量浓度>1600mg/L,经树脂吸附处理后苯胺质量浓度<2mg/L,苯胺去除率>99.9%,COD去除率>97%,树脂工作吸附量达120g/L,脱附率>98%;苯基周位酸酸析母液经树脂吸附、混凝沉淀处理后,苯基周位酸质量浓度<190mg/L,苯基周位酸去除率为94.8%,COD去除率为94.3%,氨基值去除率为80%,脱附率>99%。  相似文献   

6.
树脂吸附法处理对氨基苯酚废水   总被引:3,自引:2,他引:1  
采用自制的NDA-99特种复合功能树脂处理对氨基苯酚(PAP)生产废水,考察了各种因素对吸附和脱附效果的影响。小试实验结果得出的工艺条件为:吸附流量2.0BV/h,吸附温度15℃,单柱吸附量10BV;脱附剂为2BV盐酸(质量分数1.5%)+2BV水。中试试验结果表明,在上述工艺条件下,NDA-99树脂处理PAP废水的吸附性能和脱附性能稳定,平均COD去除率约为93%,平均PAP脱附率达98%。  相似文献   

7.
粉末活性炭-A/O工艺处理尼龙66生产废水   总被引:2,自引:0,他引:2  
史乐君  张奎  李向阳 《化工环保》2006,26(6):502-505
采用粉末活性炭-A/O生物脱氮工艺对尼龙66生产废水进行处理,对投加与不投加粉末活性炭两种情况下该工艺的生产运行数据进行了汇总和整理。实验结果表明:在废水水量及污染物浓度增加的条件下,通过投加PAC,使系统对废水COD的去除率从85.7%提高到90.9%,NH3-N去除率由51.06%提高到67.66%,出水COD和NH3-N质量浓度分别达到112.53mg/L和19.51mg/L,均低于国家二级排放标准,解决了企业面临的处理废水不达标的问题。  相似文献   

8.
倒置A2/O工艺氮平衡与脱氮效率的分析   总被引:5,自引:0,他引:5  
研究了倒置A^2/O工艺中的氮平衡和脱氮效率,并对影响脱氮效率的回流比和碳氮质量比进行分析。根据广州某城市污水处理厂水质特点,设计总回流比为3.0,其中污泥回流比为1.0,混合液回流比为2.0,理论总氮去除率为78.75%,实际运行总氮去除率达64.42%。  相似文献   

9.
用沸石吸附稀土冶炼氯铵废水中的氨氮   总被引:4,自引:0,他引:4  
用天然沸石对稀土冶炼氯铵废水中的氨氮进行吸附实验。通过实验得到的最佳工艺条件为:废水pH7—8、沸石粒径0.5—1.0mm、沸石投加量60g;先以300r/min搅拌1min,再以60r/min搅拌30min,沉降30min。稀土冶炼氯铵废水经沸石吸附处理后,废水中的氨氮质量浓度由13013mg/L降至6168mg/L,氨氮去除率达52.6%。  相似文献   

10.
氨基淀粉絮凝剂合成工艺   总被引:8,自引:1,他引:8  
相波  李义久  倪亚明 《化工环保》2003,23(5):300-303
以玉米淀粉为原料,以环氧氯丙烷(ECH)作交联剂,合成高交联淀粉(CS);以HC1O4作引发剂,以ECH作醚化剂,合成中间产物3-氯-2-羟基丙烯基交联淀粉(CHCS),在碱性条件下再与乙二胺反应,得到对重金属离子具有螯合能力的氨基淀粉(CAS)。最佳醚化条件:CS含水质量分数为7.0%,ECH与CS的摩尔比为2.5:1,HC104与CS的摩尔比为0.03:1,反应时间为8h,反应温度为95℃。以该法制得的CAS对废水中铜离子的去除能力为78.5mg/g。  相似文献   

11.
Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.  相似文献   

12.
Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.  相似文献   

13.
高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6~9,COD 302mg/L,BOD5 108mg/L,SS30mg/L,色度36倍,水质达到GB8978--1996(污水综合排放标准》三级标准。  相似文献   

14.
Application of Cellulose Microfibrils in Polymer Nanocomposites   总被引:1,自引:0,他引:1  
Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.  相似文献   

15.
Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.  相似文献   

16.
Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.  相似文献   

17.
In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.  相似文献   

18.
The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.  相似文献   

19.
During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH4 + immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH4 + immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH4 + immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO2 productionand net NH4 + immobilization, but not net Nmineralization. The immobilization of 15NH4 +caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized 15NH4 + intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH4 +immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.  相似文献   

20.
Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by 1H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号