阳离子聚丙烯酰胺-TiO2复配絮凝剂的合成及性能

以甲基丙烯酰氧乙基三甲基氯化铵(DMC)和丙烯酰胺(AM)为单体,K2S2O8-NaHSO3为引发剂,采用水溶液聚合法合成了阳离子聚丙烯酰胺P(DMC-AM),将表面处理后的纳米TiO2与P(DMC-AM)复配,得到P(DMC-AM)-TiO2复配絮凝剂.考察了原料配比、反应条件对P(DMC-AM)黏度的影响,结果表明:在m(DMC):m(AM)=0.18、引发剂加入量为0.5%(质量分数,下同)、聚合反应时间3 h、聚合溶液pH=4.0条件下,P(DMC-AM)絮凝剂的特性黏度最佳;纳米TiO2加入量为5%时,复配絮凝剂对酸性黑10B染料模拟废水的脱色性能最好.     

阳离子絮凝剂P(AM-DMC)的合成及其对活性染料废水的絮凝脱色

以K2S2O8-脲为引发剂,通过自由基聚合法合成了丙烯酰胺-2-甲基丙烯酰氧乙基三甲基氯化铵P（AM—DMC）絮凝剂,并研究了其对4种活性染料模拟废水的脱色效果,考察了P（AM—DMC）加入量、阳离子度、特性粘数、染料溶液pH等因素对脱色效果的影响。实验结果表明：最佳P（AM—DMC）加入量随染料分子中磺酸基数目的增加而增加,随絮凝剂阳离子度的增大而减少;阳离子度大于52％时,最高脱色率基本相同;特性粘数对脱色效果影响很小;在染料溶液为弱酸性及中性条件下,P（AM—DMC）的脱色效果较好。P（AM—DMC）对活性染料废水的脱色机理是,P（AM—DMC）中的-N^＋（CH3）3与染料分子中的-SO3^-结合,生成-N^＋（CH3）3SO3^-,同时也形成了分子间氢键,通过键合作用使染料分子聚集沉降。     

阳离子淀粉-丙烯酰胺接枝共聚物絮凝剂的制备及其絮凝性能

研究了阳离子淀粉与丙烯酰胺接枝共聚反应制备阳离子型絮凝剂的工艺,并用硅藻土悬浊液及实际水样对产物的絮凝性能进行了考察。其最佳合成条件：阳离子淀粉与丙烯酰胺的质量比为1：4,引发剂加入量为丙烯酰胺质量的0．1％,反应温度50℃,反应时间3h。絮凝效果实验中,接枝共聚物絮凝剂的最佳加入量为4mg／L。与阳离子淀粉和阳离子聚丙烯酰胺絮凝剂相比,接枝共聚物絮凝剂对渭河水及造纸网下白水的絮凝效果更好。     

碳酸锶生产废水的处理方法

该发明涉及一种碳酸锶生产废水的处理方法。过程为：废水用质量分数为25％～50％的H2O2溶液与质量分数为0．01％～5．00％的市售聚丙烯酰胺絮凝剂的水溶液澄清、再用质量分数为25％～50％的H2O2溶液脱硫、然后加入锰的彰和铁的氧化物分解。采用该发明的碳酸锶生产废水处理方法，出水中杂质含量少，可循环利用于碳酸锶生产过程的硫化锶浸取工段，对产品碳酸锶质量的改善有利；     

非离子型聚丙烯酰胺絮凝剂的制备及其絮凝性能

以丙烯酰胺（AM）和烷基酚聚醚（APAP）为单体,采用反相乳液聚合法制备了流动性好的非离子型聚丙烯酰胺絮凝剂（PAM-APAP）。考察了乳化剂和引发剂的种类、单体总质量分数、单体配比和反应温度等因素对聚合反应的影响。实验结果表明,制备PAM-APAP的最佳工艺条件为：单体总质量分数35%、m（AM）∶m（APAP）=9.0∶1.0、Span80+Tween80复配乳化剂加入量为油水总质量的7%、m（Span80）∶m（Tween80）=7.0∶1.5、V50加入量为单体总质量的1.5‰、反应温度50℃。PAM-APAP具有较好的絮凝效果,与其他絮凝剂相比用量较少,在加入量为100mg/L时,对聚合物驱油中产生的含聚合物污水的浊度去除率为87.9%,去油率为89.5%,且絮体不黏壁。     

新型污泥脱水絮凝剂的研制

以累托石和虾蟹壳为主要原料,制备出一种新型污泥脱水絮凝剂。研究了该絮凝剂的制备工艺条件,探讨了该絮凝剂的絮凝机理。该絮凝剂的最佳配方为：天然有机高分子材料与改性累托石质量比1：6,将其配制成质量分数为1％的絮凝剂工作液,处理污泥的最佳加入量为1mL／L,最佳沉降时间为20min。与传统絮凝剂聚丙烯酰胺相比,污泥脱水率提高了5．47％,污泥沉降时间缩短了33．33％,吨污泥单耗絮凝剂成本下降了4％,且处理过程中的二次污染大幅度减小。     

含氟改性聚丙烯酰胺絮凝剂的合成及其絮凝性能

以全氟辛基乙基丙烯酸十二氟庚酯(PFMA)为疏水单体,与丙烯酰胺(AM)、二烯丙基二甲基氯化铵(DMDAAC)通过自由基胶束共聚法制得含氟改性聚丙烯酰胺(FPAD)絮凝剂。最佳聚合反应工艺条件:PFMA质量分数为0.3%,引发剂质量分数为0.3%,DMDAAC质量分数为15%,共聚反应温度为50℃。用FPAD处理初始透光率为20%、初始COD为282mg/L的废水,当FPAD加入量为15mg/L、絮凝体系pH为6时,废水透光率最高,可达98.7%;pH为6～9时,废水透光率和COD去除率均较高。     

经济型阳离子淀粉絮凝剂的制备及其对印染废水的处理效果

采用玉米淀粉为原料、氯化缩水甘油三甲基铵（GTA）作阳离子化试剂、水-乙醇混合液作分散剂、NaOH作碱催化剂,制备了经济型阳离子淀粉絮凝剂（简称经济型阳离子淀粉）。实验结果表明：在淀粉加入量110g、GTA加入量30g、NaOH加入量1．6g、分散剂中m（水）：m（乙醇）=1：1、m（分散剂）：m（淀粉）=0．50：1、反应温度80℃、反应时间2．5h的条件下,可制得取代度（DS）为0．31的经济型阳离子淀粉;用该经济型阳离子淀粉与聚丙烯酰胺（PAM）联用处理印染废水,当经济型阳离子淀粉加入量为140mg／L、PAM加入量为4mg/L、废水pH为8时,印染废水的色度去除率和COD去除率分别达92％和82％。该方法絮凝效果好,药剂费用低,产生的污泥少。     

O3氧化法和O3-H2O2氧化法去除水中聚丙烯酰胺

采用O3氧化法和O3-H2O2氧化法去除水中的聚丙烯酰胺（PAM）,分别考察了反应时间、O3质量浓度、n（H2O2）∶n（O3）和溶液pH对PAM去除效果的影响。实验结果表明：O3氧化的最佳操作条件为反应时间30 min、O3质量浓度22.6 mg/L、溶液pH 8.5,O3-H2O2氧化的最佳操作条件为反应时间10 min、O3质量浓度22.6 mg/L、n（H2O2）∶n（O3）=0.1、溶液pH 8.5;在最佳操作条件下,O3氧化和O3-H2O2氧化均可有效降低PAM溶液的黏度和PAM质量浓度,但对COD的去除效果不佳,黏度可降至和蒸馏水相近,PAM的去除率可达80%以上,而COD的去除率分别约为15%和28%;O3-H2O2氧化后的PAM比O3氧化后的PAM更容易被微生物利用,两种氧化预处理方法均有利于后续的生化处理。     

硫酸生产中废钒催化剂回收工艺研究

采用H2SO4浸取、NH4HSO3还原、NH4NO3氧化、KOH精制的方法回收废钒催化剂中的V2O5。实验结果表明,还原反应的最佳条件为：n（NH4HSO3）／n（V2O5）=1．10,还原反应温度90℃,还原反应时间2．0h。氧化反应的最佳条件为：n（KOH）／n（VO^＋）=1．10,氧化反应温度60℃,液固比8,氧化反应时间60min。该方法V2O5回收率达90．3％以上,V2O5纯度达82％以上。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Methane generation from corncobs treated with xylanolytic consortia

Consortia were developed for the treatment of corncobs for use as a feedstock in a biogas fermentor. The treatment of corncobs with xylanolytic consortia enhanced the production of methane and biogas. All five consortia developed produced the maximum biogas and methane at a 6% loading rate and 20 days hydraulic retention time (HRT). The maximum biogas yield of 0.59m³/kg volatile solids (VS) with a methane content of 62% was produced with the KK-10 consortium. This was apparently due to a maximum hemicellulose degradation of 88%.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

Preparation and Biodegradation of Starch/Polycaprolactone Films

Starch granules were modified with trisodium trimetaphosphate (TSTP) and characterized by P³¹-NMR, FTIR and DSC. Seventy-micron films were prepared from modified starch and polycaprolactone blends by solvent casting technique. Three different types of films—PCL (100% polycaprolactone), MOD-ST/PCL (50% modified starch and 50% polycaprolactone blend) and NONMOD-ST/PCL (50% nonmodified starch and 50% polycaprolactone blends)—were prepared, and their thermal, mechanical, and morphologic properties were investigated to show the increased performance of PCL with the addition of starch and also the effect of modification. It was observed that with the addition of starch the Young's modulus of polycaprolactone was increased and became less ductile, whereas tensile strength and elongation at break values decreased. Biodegradation of these films was inspected under different aerobic environments with the presence of Pseudomonas putida, activated sludge, and compost. It was observed that whereas P. putida had almost no effect on degradation during 90 days, with the presence of activated sludge, considerable deformation of films was observed even in the first 7 days of degradation. In a compost environment, degradation was even faster, and all polymer films were broken into pieces within first 7 days of degradation and no film remained after 15 days.