改性粉煤灰对活性艳兰染料吸附性能的研究

采用添加熟石灰并升温活化的方法对粉煤灰进行改性,研究了粉煤灰改性的适宜条件及其对活性艳兰染料的吸附脱色规律。试验结果表明,活性艳兰染料溶液浓度60mg/L,改性粉煤灰用量40g/L,pH范围5~10,搅拌吸附时间30min,脱色率可达98%以上。改性粉煤灰对活性艳兰染料的脱色吸附符合Freundlich方程。随着吸附温度的升高,改性粉煤灰的吸附能力下降。     

镁盐复合混凝剂应用于活性染料印染废水脱色的实验研究

采用镁盐与亚铁盐混合复配对活性染料印染废水进行脱色处理.考察该复合混凝剂的组分配比、pH值和投加量对脱色率的影响,并与单一组分混凝剂的脱色效果作对比,同时初步分析了复合混凝剂的脱色机理.结果表明:复合混凝剂MgSO4-FeSO4·7H2O的脱色效果明显优于单一组分,表现出显著的协同效应;对于80 mg/L的活性黑KN-B印染废水(色度为1000倍),在复合混凝剂投加量为556 mg/L、pH值在10.9左右时,脱色率可以达到99.07%;主要脱色机理表现为镁盐和亚铁盐在高pH值的环境下共沉淀生成氢氧化物絮状物吸附溶液中的染料分子一起沉降.该吸附主要为电中和吸附.吸附等温线符合Langmuir方程,复合吸附剂的饱和吸附量达1.1614 g/g.     

改性粉煤灰对活性艳兰染料吸附性能的研究

采用添加熟石灰并升温活化的方法对粉煤灰进行改性，研究了粉煤灰改性的适宜条件及其对活性艳兰染料的吸附脱色规律。试验结果表明，活性艳兰染料溶液浓度60mg／L，改性粉煤灰用量40g／L，pH范围5-10，搅拌吸附时间30min脱色率可达98％以上。改性粉煤灰对活性艳兰染料的脱色吸附符合Freundlich方程。随着吸附温度的升高，改性粉煤灰的吸附能力下降。     

利用钢渣对聚驱采油废水进行深度处理

利用钢渣对模拟聚驱采油废水进行深度处理,依靠吸附作用去除水中的HPAM。考察了钢渣粒径、搅拌速度、pH以及吸附时间对HPAM去除率的影响,进行了吸附等温线和吸附热力学分析,并对钢渣进行了吸附再生实验。当搅拌速度为250r／min,pH为2～10,吸附时间为90rain,钢渣粒径为10-16目、投加量为100g／100mL时,HPAM的去除率可达到84％以上。钢渣对HPAM的吸附符合Langmuir等温式,吸附自由能变和吸附焓的结果都表明,该吸附属于物理吸附。吸附之后的钢渣可以通过600℃焚烧得到再生,再生后仍可保持良好的吸附性能。     

铁阳极电化学对直接大红4BE模拟废水脱色

对铁阳极电化学处理直接大红4BE染料废水脱色率和脱色能耗的影响因素进行研究。考察了电流密度、染料溶液初始pH值、染料初始浓度和支持电解质Na2SO4浓度对脱色性能的影响。结果表明,电流密度、染料废水初始pH、染料初始浓度、支持电解质浓度对脱色率和脱色能耗产生较大影响。在电流密度1.667 mA/cm2、pH值6.54、染料浓度50mg/L、Na2SO4浓度0.01 mol/L、温度20℃、搅拌速度600 r/min、电解时间60 min条件下,脱色率达到92.1%,脱色能耗1.298 kWh/kg染料、铁阳极消耗量41 mg/400 mL染料模拟废水。     

层状氢氧化镁铝对偶氮染料酸性黑10B的脱色性能研究

分别用层状氢氧化镁铝(LDH)和焙烧层状氢氧化镁铝(CLDH)作为吸附剂吸附脱除水溶液中偶氮染料酸性黑10B.考察了脱色时间、pH值、吸附剂的投加量、温度、染料初始浓度和焙烧温度等因素对脱色率的影响.结果表明,LDH及CLDH对酸性黑10B染料具有良好的脱除效果,室温下,10g/L LDH和1g/L的CLDH对浓度为100mg/L的染料的脱色率分别达95.93%和99.97%.pH值是影响吸附能力的关键因素,吸附剂对溶液pH值有一定缓冲作用.LDH及CLDH对酸性黑10B吸附结果符合Langmuir吸附等温式.饱和吸附后的LDH及CLDH用高温热解法再生,吸附性能良好,随再生次数增多,脱色率下降.     

Mg-Al水滑石对偶氮染料活性艳红X-3B的脱色性能研究

采用共沉淀法合成出一系列镁铝摩尔比不同的碳酸根型水滑石（LDHs）,经500℃高温煅烧制备出镁铝复合氧化物CLDH,并用X-射线、红外光谱对它们进行表征。考查了吸附剂投加量、反应时间、初始pH值等因素对LDHs和CLDH处理阴离子染料活性艳红X-3B模拟废水效果的影响,并对吸附机理进行探讨。实验结果表明：以镁铝摩尔比为3∶1时制得的水滑石对活性艳红X-3B溶液的脱色效果最好。水滑石LDHs及其焙烧产物CLDH对活性艳红X-3B染料均具有较好的吸附性能,最佳反应时间分别为60 min和30 min;在较宽的pH范围内二者的脱色性能稳定,且CLDH对该染料的吸附效果要优于LDHs。LDHs及CLDH对活性艳红X-3B的吸附结果符合Langmuir吸附等温式,25℃下饱和吸附量分别为263.77 mg/g和875.23 mg/g。LDHs及CLDH的吸附机理分别为离子交换和层状结构重建。饱和吸附后的CLDH用高温热解法再生,吸附性能良好,随再生次数增多,脱色率下降。     

ACF电极电解处理含NaCl结晶紫染料废水的研究

以吸附结晶紫达到饱和的活性炭纤维为阳极,在NaCl介质中对初始浓度为100 mg/L的结晶紫染料废水进行了电解脱色处理。实验考察了NaCl浓度、pH值和电流密度等对溶液脱色率的影响,测定了电解时溶液中生成的游离氯浓度及不同电解时间后溶液的紫外-可见吸收光谱曲线,并对不同电解时间后溶液的归一化吸光度比值进行了计算。结果发现,溶液中所产生的游离氯的浓度随电解时间的增加快速上升,20 min时就几乎达到了最大值;在活性氯的作用下,结晶紫分子中的大π共轭体系被破坏,溶液迅速脱色;电解液中所含的NaCl浓度、电解液的pH值和电流密度等都对脱色率有影响;在一定实验条件下,初始浓度为100 mg/L的结晶紫染料废水在电解60 min后脱色率可高达99.3%。     

污泥活性炭对次甲基蓝废水的吸附

立足于污泥的资源化,利用化学活化法制得的污泥基活性炭,处理次甲基蓝染料废水.考察了污泥活性炭的粒径以及染料废水的pH值对染料脱色效果以及活性炭的吸附量的影响,并对吸附过程进行等温吸附线和吸附动力学分析.结果表明,在本研究的范围内,污泥活性炭的粒径越小、染料废水的pH值越高,则污泥活性炭对染料废水的吸附效果越好.当粒径在200目以上时,去除率及吸附量分别为88.2％和136.7 mg/g;当pH值为11时,去除率和吸附量分别为90.4％和91.9 mg/g.污泥活性炭对次甲基蓝染料的吸附脱除符合Langmuir吸附等温线和Lagergren准二级动力学方程.     

电气石在环境领域的最新应用研究：处理雅格素蓝BF-BR染料废水

在氧化剂(H2O2)的协同作用下,电气石对雅格素蓝BF-BR染料废水具有良好的脱色能力,脱色率与电气石用量、氧化剂用量、水浴温度、作用时间呈正相关性,溶液pH值为2和12时,脱色率最大.正交实验优化了工艺条件:氧化剂用量1.5 mL、作用时间9 min、电气石用量1g、水浴温度363 K、pH=2,此时脱色率可达到100%.动力学研究表明:雅格素蓝BF-BR染料废水的脱色反应为一级反应,其反应表观动力学方程为:-lnCR=0.36733t-lnC0(R=0.9827),反应速率常数为k=0.36733 min-1,反应半衰期为t1/2=1.887 min.机理的初步分析表明:脱色过程是矿物催化-类芬顿反应.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)