Biotreatment of hydrogen sulfide- and ammonia-containing waste gases by fluidized bed bioreactor

Gas mixtures of H2S and NH3 are the focus of this study of research concerning gases generated from animal husbandry and treatments of anaerobic wastewater lagoons. A heterotrophic microflora (a mixture of Pseudomonas putida for H2S and Arthrobacter oxydans for NH3) was immobilized with Ca-alginate and packed into a fluidized bed reactor to simultaneously decompose H2S and NH3. This bioreactor was continuously supplied with H2S and NH3 separately or together at various ratios. The removal efficiency, removal rate, and metabolic product of the bioreactor were studied. The results showed that the efficiency remained above 95% when the inlet H2S concentration was below 30 ppm at 36 L/hr. Furthermore, the apparent maximum removal and the apparent half-saturation constant were 7.0 x 10(-8) g-S/cell/day and 76.2 ppm, respectively, in this study. The element sulfur as a main product prevented acidification of the biofilter, which maintained the stability of the operation. As for NH3, the greater than 90% removal rate was achieved as long as the inlet concentration was controlled below 100 ppm at a flow rate of 27 L/hr. In the NH3 inlet, the apparent maximum removal and the apparent half-saturation constant were 1.88 x 10(-6) g-N/cell/day and 30.5 ppm, respectively. Kinetic analysis showed that 60 ppm of NH3 significantly suppressed the H2S removal by Pseudomonas putida, but H2S in the range of 5-60 ppm did not affect NH3 removal by Arthrobacter oxydans. Results from bioaerosol analysis in the bioreactor suggest that the co-immobilized cell technique applied for gas removal creates less environmental impact.     

以焦炭为填料的生物滴滤塔处理含挥发性脂肪酸臭气

在以焦炭为填料的生物滴滤塔对挥发性脂肪酸臭气的处理研究中考察了空床停留时间、臭气浓度、体积负荷以及进气温度等参数对净化效果的影响。结果表明,空床停留时间较长时对臭气降解有利。在停留时间超过97 s时,能实现完全降解;此外,净化率随臭气浓度和体积负荷的不断增加呈先增加后降低的趋势。当臭气浓度为24.29 mg/m³即臭气的体积负荷为3 g/（m³·h）时,去除率约为96%;当臭气浓度增至1 345.74 mg/m³即体积负荷增至18 g/（m³·h）,去除率达100%;然而,当臭气浓度增至4 934.38 mg/m³即体积负荷增至66 g/（m³·h）时,去除率降至73.1%。另外,进气温度对净化率也有一定程度影响。当进气温度较低时,净化效率相对较高。     

捕集植物纤维性粉尘的研究

植物纤维性粉尘因其固有特性 ,在除尘技术中是一个没有解决好的难题。通过理论分析、实验研究与工程应用 ,利用流化床除尘器解决了这一问题 ,实现了除尘器的高效、低阻和可靠运行     

基于正交实验的颗粒移动床烟气脱硫工艺参数优化

石灰石颗粒移动床脱硫工艺参数是影响脱硫效率和操作压降变化的重要因素,考虑到工艺参数对脱硫过程的影响,基于正交实验方法,通过直观分析和方差分析得到喷淋密度、空床气速、SO2浓度、烟气温度和床层下移速度对脱硫效率影响程度的主次顺序和脱硫效率与各因素之间的关系,并且分析了各因素对脱硫效率的影响规律。研究发现,各因素对脱硫效率的影响程度依次是空床气速>喷淋密度>SO2浓度>烟气温度>床层下移速度。喷淋密度对脱硫效率的影响高度显著,呈正相关;空床气速对脱硫效率的影响高度显著,呈负相关;SO2浓度和烟气温度对脱硫效率有影响但不显著,呈负相关。床层下移速度与脱硫效率呈正相关。     

The treatment of waste air containing phenol vapors in biotrickling filter

This research aimed at investigating the biodegradation of phenol contaminated-air streams in biotrickling filter. The effect of inlet concentration (200-1000 ppmv) and empty bed contact time (EBCT) (15-60 s) were investigated under steady state, transient and shock loading, and shutdown periods. Upon rapid start up operation, inlet phenol concentrations of up to 1000 ppmv did not significantly affect the performance of the biotrickling filter at EBCT of 60 s, so that removal efficiency was well greater than 99%. In addition, the EBCT as low as 30 s did not have detrimental effects on the efficiency of the bioreactor and phenol removal was greater than 99%. Decreasing the EBCT to 15s reduced the removal efficiency to around 92%. The maximum elimination capacity obtained in the biotrickling filter was 642 g(phenol) m(-3) h(-1), where the removal efficiency was only 57%. Results from the transient loading experiments revealed that the biotrickling filter could effectively handle the variations of the inlet loads without the phenol removal capacity being significantly affected.     

Effect of gas velocity and influent concentration on biofiltration of gasoline off-gas from soil vapor extraction

This study was conducted to evaluate the effects of gas inlet concentration and velocity on the biofiltration of gasoline vapor. Gasoline vapor was treated using a compost biofilter operated in an upflow mode for about 3 months. The inlet concentration of gasoline total petroleum hydrocarbon (TPH) ranged from about 300 to 7000 mgm(-3) and gas was injected at velocities of 6 and 15 mh(-1) (empty bed residence time (EBRT)=10 and 4 min, respectively). The maximum elimination capacities of TPH at 6 and 15 mh(-1) found in this research were over 24 and 19 gm(-3) of filling material h(-1), respectively. TPH removal data was fit using a first-order kinetic relationship. In the low concentration range of 300-3000 mg m(-3), the first-order kinetic constants varied between about 0.10 and 0.29 min(-1) regardless of gas velocities. At TPH concentrations greater than 3000 mgm(-3), the first-order kinetic constants were about 0.09 and 0.07 min(-1) at gas velocities of 6 mh(-1) and 15 mh(-1), respectively. To evaluate microbial dynamics, dehydrogenase activity, CO2 generation and microbial species diversity were analyzed. Dehydrogenase activity could be used as an indicator of microbial activity. TPH removal corresponded well with CO2 evolution. The average CO2 recovery efficiency for the entire biofilter ranged between 60% and 70%. When the gas velocity was 6 mh(-1), most of the microbial activity and TPH removal occurred in the first quarter of the biofilter. However, when the gas velocity was 15 mh(-1), the entire column contributed to removal. Spatial and temporal variations in the biofilter microbial population were also observed. Nearly 60% of the colonies isolated from the compost media prior to biofiltration were Bacillus. After 90 days of biofiltration, the predominant species in the lower portion (0-50 cm) of the filter were Rhodococcus, while Pseudomonas and Acinetobacter dominated the upper portion (75-100 cm).     

四级三相式生物流化床分段进水工艺脱氮效能

对四级三相式生物流化床分段进水工艺脱氮效能进行了研究。通过改变进水C/N比、水力停留时间(HRT)和污泥回流比,考察了系统的脱氮效能,并与流化床A/O工艺脱氮效能进行对比。出水氨氮均小于1 mg/L,去除率保持在97%以上,TN去除率最高可达90%,出水水质均能够保证达标。在相同水质和运行条件下,将四级三相式生物流化床分段进水工艺与流化床A/O工艺进行对比,前者从脱氮效能和节约能源方面均表现出较强的优势。四级三相式生物流化床分段进水工艺无需外加碳源和内回流系统,是一种低碳节能的污水脱氮新工艺。     

Trace metal distribution and control in the pilot-scale bubbling fluidized bed combustor equipped with the pulse-jet fabric filter,limestone injection,and the humidification reactor

This work focused on trace metal behavior and removal in a fabric filter or in a humidification reactor during the cofiring of sawdust and refuse-derived fuels (RDFs) in a pilot-scale bubbling fluidized bed (BFB) boiler. Trace metal emissions measurements before and after the fabric filter revealed that removal efficiency in the fabric filter was in the range of 80-100%, and that the European Union (EU) Directive on Incineration of Waste restrictions for trace metal emissions are easily achieved even if addition of RDFs substantially increases the concentration of trace metals in fuel blends. Limestone injection enhanced the removal of As and Se but had no noticeable effect on the removal of other trace metals. Extensive formation of HgCl2 and condensation on fly ash particles during sawdust plus 40% RDF cofiring resulted in a 92% Hg removal efficiency in the fabric filter. Limestone injection had no effect on the Hg removal in the fabric filter but decreased the Hg removal in a humidification reactor from 40 to 28%. Results of the bed material and fly ash analysis suggested capture of Cu, Pb, Mn, Ni, and Zn in the bed material but also suggested that these metals may be released from the bed if the fuel characteristics or process conditions are changed.     

滤料负载粉尘层对气态汞脱除性能的实验研究

通过不同性能纤维滤料负载燃煤飞灰粉尘层,来模拟袋式除尘器滤袋表面粉尘附着层,进而研究袋滤器用不同性能纤维滤料和粉尘附着层对燃煤烟气中Hg0的联合脱除性能。在固定床实验系统上分别进行了不同纤维滤料和燃煤飞灰粉尘层,以及经实验优选得到的华博特滤料负载燃煤飞灰粉尘层脱除燃煤烟气中Hg0的实验研究。结果表明,燃煤飞灰粉尘层和华博特滤料对Hg0分别有一定的脱除作用,脱除效率可达35%和42.5%,它们对Hg0的脱除是物理吸附和化学吸附共同作用的结果;同时,华博特滤料负载燃煤飞灰粉尘层对Hg0的联合脱除效率受到吸附反应温度、入口汞浓度和烟气停留时间等因素的影响,最佳脱汞率可达64.4%;吸附反应温度越高,脱除效率越低;烟气停留时间越大,脱除效率越高;入口汞浓度的提高并不一定提高华博特滤料负载飞灰粉尘层的脱汞效果。     

脉冲电晕低温等离子体提高一氧化氮氧化效率的实验研究

提高一氧化氮（NO）的氧化效率对于提高生物法处理该类废气的净化效率具有重要意义。实验研究了低温等离子体在脉冲电晕条件下氧化废气中NO的过程，考察了不同峰值电压、氧气含量、气体停留时间和添加有机物等因素对提高NO氧化效率的影响。结果表明：低温等离子法可有效地提高NO的氧化效率，主要产物为NO₂；室温条件下，当进气NO浓度590 mg/m³、脉冲频率50 Hz时，增大峰值电压、气体停留时间和进气中的氧气含量可提高NO的氧化效率；在最适峰值电压15 kV，气体停留时间5 s时，NO氧化效率为20%；在进气NO中添加甲苯、乙醇后，NO氧化效率可增加至30%以上，甲苯的效果要好于乙醇。     

活性炭三维电极流化床处理洗车废水的研究

以经吸附处理的活性炭为填充粒子,对三维电极流化床反应器处理洗车废水进行了静态条件实验研究。结果表明：三维电极流化床处理洗车废水的效果明显好于三维电极固定床和单纯的活性炭吸附。在槽电压为30 V,通气量为3 L/min, 通电时间为30 min,活性炭用量为50 g时,COD去除率最高。     

管式生物过滤器去除乙苯废气

生物过滤由于其良好的成本效益和环境友好性已经成为控制挥发性有机化合物(VOCs)含量和气味气体排放的常规技术。营养物质的均匀分布、生物膜和介质床内的气体流是成就一个性能优良的生物过滤器至关重要的因素。而由本实验室开发的管式生物过滤器(TBFs)已被证明具备此优势。本实验的管式生物过滤器以聚氨酯海绵作为填料,研究在不同有机负荷、气体停留时间(EBCT)、进气量和表面活性剂等条件下乙苯废气的去除效率(RE)。实验同时记录了管式生物过滤器启动阶段的表现。初期使附着在填料上的微生物暴露在浓度为40 mg/m3的乙苯废气中40 d,此时的气体停留时间为15 s,使微生物慢慢适应并逐步降解乙苯废气;然后连续地控制管式生物过滤器的入口乙苯浓度为40、80、120和160 mg/m3,以使有机负荷逐步升高。结果表明,乙苯去除效率随着有机负荷的增大而逐步减小。当气体停留时间从15 s增加到30 s和60 s,而有机负荷控制在38.60 g/(m3·h)时,乙苯废气去除效率略微增加。此外,随着进气量的增大乙苯废气的最大平均去除效率有所下降而此时的降解容量增大,这个过程中乙苯进气浓度保持不变。结果还表明,在营养液中加入聚乙二醇辛基苯基醚这种表面活性剂可以提高乙苯废气的去除效率。     

Filtration of fly ash using a fluidized-bed filter

This study focuses on the control of particulates with a fluidized-bed filter in exhaust gas stream. The fluidized-bed filter classified in the granular bed filtration technology was employed to demonstrate the performance for removal of fly ash at indicated operating velocities, fixed bed heights, and bed temperatures; then the collecting mechanisms of particulates by fluidized-bed filter were studied. The size distribution of fly ash passing through the fluidized-bed filter was also analyzed. The results indicate that at higher operating velocities and fixed bed heights, the removal of fly ash is more efficient and inertial impaction is the main mechanism when the fluidized-bed is operated at room temperature (25 degrees C). While operating at higher temperatures (200 degrees C), efficiency of 93.2% to 99.4% can be achieved for submicron particles. It is supposed to be the diffusion mechanism that is responsible for collecting such small particles, and high temperature is a favorable condition because of diffusion.     

生物法同时脱硫脱硝试验研究

采用轻质陶粒生物滴滤塔处理摸拟燃煤烟气中二氧化硫和氮氧化物的试验研究,探讨生物法同时脱硫脱硝的影响因素及生物降解宏观动力学。研究结果表明,生物法能有效同时去除烟气中的二氧化硫和氮氧化物,烟气同时脱硫脱硝效率分别可达99.9%和88.9%。为获得最佳烟气同时脱硫脱硝效果,二氧化硫和氮氧化物进气负荷应分别＜140 g/（m³·h）和20 g/（m³·h）,循环液pH=7～8,空床停留时间为30.28 s,喷淋密度为8.81 L/（m³·h）。     

超重力脱除模拟烟气中一氧化氮简

以NO和N₂的混合气作模拟烟气,以酸性尿素溶液为吸收剂,在超重力机中进行了脱除模拟烟气中NO实验研究。实验考察了混合气中NO初始含量、进气流量、吸收液流量、超重力机转速对NO脱除率的影响,确定了在超重力中尿素吸收NO的适宜条件。实验结果表明,在常温常压下,N₂体积流量为1.0 m³/h,控制NO初始浓度为3 300 mg/m³,吸收液流量为250 L/h,超重力机转速为650 r/min时,NO脱除率可达89.5%。     

扩体错流式生物滴滤床净化甲苯废气

采用自行设计制作的扩体错流式生物滴滤床,以甲苯为目标污染物、陶粒为填料、恶臭假单胞菌为菌源进行实验,研究了扩体错流式生物滴滤床的挂膜启动情况、甲苯进口浓度、停留时间对净化效率的影响.结果表明:(1)环境温度为17～23℃,扩体错流式生物滴滤床在10 d内完成挂膜启动,比传统生物滴滤床缩短了4 d.(2)甲苯净化效率随进口浓度的增加而逐渐下降.当甲苯进口质量浓度为1 100 mg/m~3时,净化效率为95%;当甲苯进口质量浓度维持在1 100～1 200 mg/m~3时,随停留时间的缩短,甲苯净化效率下降.(3)当停留时间分别为94、63、48 s时,甲苯净化效率分别为87%～92%、70%～74%、60%～62%.     

介质阻挡放电净化硫化氢气体的实验研究

采用介质阻挡放电等离子体技术净化恶臭气体硫化氢。考察了电压、频率、硫化氢初始浓度以及停留时间对硫化氢净化效果的影响。结果表明,介质阻挡放电可以有效消除硫化氢污染,硫化氢净化率随电压、频率以及停留时间的增加而升高,随硫化氢初始浓度增加而下降。当电压≥19kV,频率为300Hz,停留时间为1.56s,硫化氢初始质量浓度为30.1mg/m3时,硫化氢净化率接近100%。     

颗粒层非稳态过滤捕集效率的研究

为计算颗粒层非稳态过滤效率,通过改进经典过滤理论模型,考虑颗粒在过滤介质中的沉积,理论推导得出非稳态过滤效率的计算公式,而经典颗粒层过滤效率计算公式仅为此计算公式的特例。因为理论计算公式是隐函数,不便于工程实际应用,所以,在常温条件下,对非稳态过滤时的过滤时间、过滤风速、过滤层厚度、粉尘浓度和颗粒层滤料均粒径等五个因素进行了正交实验研究。采用多元回归的方法得出各影响因素与过滤效率呈显性关系的效率关联计算公式,其计算结果与实验测试结果基本吻合。     

Relationship between pressure fluctuations and generation of organic pollutants with different particle size distributions in a fluidized bed incinerator

The hydrodynamic behaviors of fluidization perhaps significantly influence the uniformity of fluidization in fluidized bed incinerator. Good uniformity of fluidization expressed the air across uniformly through the bed and the particles being distributed well in the fluid stream. The aggregates, flocs and channels of particles do not happen during fluidization. The Good uniformity will maintain high heat and mass distribution to improve reaction efficiency. These parameters include the height of static bed, gas velocity, mixing and distribution of bed particle, which have rarely been studied in previous investigations. Consequently, this study examines how the hydrodynamic parameters affect the generation of organic pollutants (BTEXs and PAHs) during incineration. The statistical and power spectral analysis of the measured pressure fluctuation during incineration are used to elucidate the relationship between behaviors of fluidization and generation of pollutants during incineration. Experimental results show the organic concentration does not increase with uniformity of fluidization decreasing. The reason may be the explosion of the gas and the consequent thermal shock destroy the coalescent bubbles to form small bubbles again and enhance the efficiency of transfer of oxygen to increase combustion efficiency. Additionally, the mean amplitude and fluidized index of pressure fluctuation similarly vary with the concentration of organic pollutants. These two indices can be used to assess the efficiency of combustion. The four particle size distributions could be divided into two groups by statistical analysis. The Gaussian and narrow distributions belong to one group and the binary and flat the other. The organic concentration of the Gaussian and narrow distributions are lower than that of the other distributions. Consequently, the bed materials should maintain narrow or Gaussian distributions to maintain a good combustion efficiency during incineration.     

厌氧流化床微生物燃料电池同步除碳脱氮产电性能影响因素

研究了厌氧流化床微生物燃料电池(AFB-MFC)除碳脱氮产电性能的影响因素。结果表明:(1)AFB-MFC对NH4+-N的去除不起作用。电压下降主要是由于进水有机基质浓度下降造成。(2)不添加NO3--N时,在满足AFB-MFC脱氮所需的电子供体条件下增加进水COD/TN有利于AFB-MFC产电。(3)3种无机氮共存下,AFB-MFC在进水有机碳与无机氮质量比(C/N)不低于1.37时,对COD、NO2--N和NO3--N具有理想的去除效果。AFB-MFB在一定进水C/N范围内(1.37～2.50),能得到稳定的输出电压及功率密度。(4)固定进水C/N时,AFB-MFC在高碳氮负荷下仍能得到较理想的NO2--N、NO3--N、COD去除效果,AFB-MFC对NH4+-N去除效果不明显;增加碳氮负荷,AFB-MFC输出电压及功率密度没有明显的改变。(5)有机基质浓度不变下,AFB-MFC中充足的电子供体可保证较高的NO3--N、COD去除率。AFB-MFC输出电压及功率密度随着时间延长而先增加至稳定值后下降。