废聚碳酸酯水解法制双酚A

以1,4-二氧六环为溶剂、NaOH为催化剂,采用废聚碳酸酯(PC)常压水解法制双酚A(BPA).对反应影响因素进行了研究.实验结果表明,在反应温度为100℃、反应时间为8h、m(NaOH):m(水+溶剂)=1:33、m(溶剂):m(PC)=4:1、m(水):m(PC)=1:1的最佳反应条件下,PC水解率大于98%,BPA收率大于95%.     

Viable chemical recycling of poly(carbonate) as a phosgene equivalent illustrated by the coproduction of bisphenol A and carbohydrate carbonates

Chemical recycling of waste poly(carbonate) (PC) to coproduce bisphenol A (BPA) and carbohydrate carbonates was studied by selecting glycerol (Gly) and glucose (Glu) as model carbohydrates (CHs). In advance of the reaction of PC with CHs, reactions with diphenyl carbonate were examined as a model PC. In dioxane at 100°C using NaOH as catalyst, Gly was converted to cyclic carbonate hydroxymethyldioxolane (HMDO) at 98% and Glu was converted to the dicarbonate (Glu-DC) at 46%, in pyridine, in addition to the production of phenol. Similar treatment of PC with Gly using KOH as a catalyst produced HMDO and BPA at very high yields and treatment with Glu produced Glu-DC and BPA in 38%–42% yields. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Chemical recycling of polycarbonate in dilute aqueous ammonia solution under hydrothermal conditions

Polycarbonate (PC) pellets were subjected to dilute aqueous ammonia solution under hydrothermal conditions in a semi-batch reactor at temperatures ranging from 433 to 463 K and at a pressure of 10 MPa. The PC pellets were almost completely converted to bisphenol A (BPA). During an initial certain period, referred to as an induction time, neither BPA nor total organic carbon in solution were detected, and the BPA yield increased with time. The monomer yield was well represented by a surface reaction model, two-thirds-order reaction with respect to the mass of unreacted PC. The overall rate constant of the reaction in 0.6 mol/kg aqueous ammonia solution at 433 K was about 15 times greater than that in 0.6 mol/kg NaOH solution. The rate constant at 433 K was proportional to the ammonia or NaOH concentration. There was a correlation between the induction time and temperature, as well as the ammonia or NaOH concentration. By carrying out the reaction in aqueous mixtures of (NH₄)₂SO₄ and NaOH at various concentrations of NaOH, ammonia was confirmed not to function as an alkaline reagent, but as a nucleophile reagent.     

丙烯腈生产废水中聚合物的资源化利用

以丙烯腈生产废水中的丙烯腈低聚物为原料制备聚丙烯酰胺。通过正交实验考察了水解反应条件和交联反应条件对反应的影响。FTIR表征结果显示,丙烯腈低聚物中的氰基已完全水解为酰胺基,产物聚丙烯酰胺中含有酰胺基和羧基。实验结果表明,在自来水加入量100 m L、水解反应温度95℃、m(Na OH)∶m(丙烯腈低聚物)=2.0、水解反应时间3 h的最佳水解反应条件,交联反应温度60℃、质量分数37%~40%的甲醛加入量6 m L、交联反应时间2 h的最佳交联反应条件下,处理20 g丙烯腈低聚物,可得到产物聚丙烯酰胺14.50 g,聚丙烯酰胺的水解度为21.1%、相对分子质量为2.7×106。产品性能满足Q/SH 0046—2007《钻井液用聚丙烯酰胺技术要求》中部分水解聚丙烯酰胺的性能要求。     

Alkaline hydrolysis of photovoltaic backsheet containing PET and PVDF for the recycling of PVDF

Recovering fluorine from end-of-life products is crucial for the sustainable production and consumption of fluorine-containing compounds because fluorspar, an important natural resource for fluorine, is currently at a supply risk. In this study, we investigated the feasibility of chemically recycling a fluorine-containing photovoltaic (PV) backsheet for fluoropolymer recycling. Herein, a PV backsheet consisting of laminated polyethylene terephthalate (PET) and polyvinylidene fluoride (PVDF) was treated with different concentrations of sodium hydroxide (NaOH) to hydrolyze the PET layer to water-soluble sodium terephthalate (Na₂TP) and to separate pure PVDF layer as a solid material. Optimized alkaline conditions (up to 10 M NaOH at 100 °C for 2 h) were determined, under which 87% of the PET layer could be decomposed without any significant deterioration of the PVDF layer. The hydrolysis kinetics of PET layer in NaOH could be explained by the modified shrinking-core model. Considering that the mass of end-of-life PV panels in Japan is estimated to increase to approximately 280,000 tons per year by 2036, PV backsheets are attractive candidates for fluoropolymer recycling, which can be effectively achieved using chemical recycling approach demonstrated in this study.

     

Optimization of thermo-chemical pretreatment and enzymatic hydrolysis of kitchen wastes

The use of abundant waste materials with high carbohydrate content may contribute substantially to reduction of biofuels production cost. The present study aimed at optimizing the combined effect of thermo-chemical pretreatment and enzymatic hydrolysis of kitchen wastes (KW) for maximizing the production of fermentable soluble sugars. To this end, acid pretreatment of KW samples was performed with hydrochloric acid (0–3% HCl) at 30–100 °C for 0–120 min treatment time. Alternatively, alkaline pretreatment of KW samples was performed with potassium hydroxide solution (0–11%) at constant temperature and time (0 °C and 20 min, respectively). KOH pretreatment at such conditions targets to degrade the resistant starch of KW samples. Both acid and alkaline pretreatments were followed by addition of variable levels of enzyme dosage (0–3.6% v/v α-amylase and 0–3.2% v/v amyloglucosidase-AMG) at constant pH, temperature and time (pH = 5, T = 50 °C and t = 30 min, respectively). Based on our results, glucose concentration increased by ～300% after pretreatment with either acid or KOH in combination with enzymatic hydrolysis (2% HCl, 85 °C, 80 min, 0.1% α-amylase, AMG, and 1% KOH, 0 °C, 20 min, 1.1% α-amylase, 0.4% AMG) compared to raw (untreated) KW. Estimating the different Y_G yields at KW loading of 5%, an increase of 192% and 121% for total soluble monosugars and total soluble sugars, respectively, was succeeded compared to untreated KW. The effect of solids loading on the obtained sugar yields using the optimum conditions for thermo-chemical pretreatment followed by enzymatic hydrolysis was also tested resulting to 27.5% increase of the soluble glucose yield when half of the solids loading (2.5%) was used. A decrease of total soluble sugars yield by 32.2% was observed when solely acid hydrolysis at optimum conditions from our previous study was applied at 30% solids loading.     

The Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-Lactide) Prepared by Different Synthesis Procedure

Different synthesis methods were applied to determine optimal conditions for polymerization of (3S)-cis-3,6-dimethyl-1,4-dioxane-2,5-dione (l-lactide), in order to obtain poly(l-lactide) (PLLA). Bulk polymerizations (in vacuum sealed vessel, high pressure reactor and in microwave field) were performed with tin(II) 2-ethylhexanoate as the initiator. Synthesis in the vacuum sealed vessel was carried out at the temperature of 150 °C. To reduce the reaction time second polymerization process was carried out in the high pressure reactor at 100 °C and at the pressure of 138 kPa. The third type of rapid synthesis was done in the microwave reactor at 100 °C, using frequency of 2.45 GHz and power of 150 W at the temperature of 100 °C. The temperature in this method was controlled via infrared system for in-bulk measuring. The solution polymerization (with trifluoromethanesulfonic acid as initiator) was possible even at the temperature of 40 °C, yielding PLLA with narrow molecular weight distribution in a very short period of time (less than 6 h). The obtained polymers had the number-average molecular weights ranging from 43,000 to 178,000 g mol⁻¹ (polydispersity index ranging from 1 to 3) according to the gel permeation chromatography measurements. The polymer structure was characterized by Fourier transform infrared and NMR spectroscopy. Thermal properties of the obtained polymers were investigated using thermogravimetry and differential scanning calorimetry.     

Study on the Thermo-Mechanical and Biodegradable Properties of Shellac Films Grafted with Acrylic Monomers by Gamma Radiation

Shellac (SL) films were prepared by casting and were grafted with various acrylic monomers of different functionalities using gamma radiation. Different formulations of shellac with varying concentrations (3, 5 and 7%) of these acrylic monomers such as 2-hydroxyethyl methacrylate (HEMA), 2-ethylhexyl acrylate (EHA) and 1,4-butanediol diacrylate (BDDA) in methanol were prepared. The pure shellac and other treated films were then irradiated under gamma radiation (Co-60) at different doses (0.5–5 kGy) at a dose rate of 3.5 kGy/h where 1 Gy = 1 J/kg = 100 rads. The mechanical properties like tensile strength (TS) and elongation at break (Eb) of the prepared films were studied. The mechanical properties of the irradiated shellac films demonstrated superior values. Among the formulations, shellac grafted with BDDA (SL-g-BDDA) showed the highest TS and Eb values which were 543 and 168% higher than those of raw shellac films, respectively. The water uptake behavior of raw and treated films was also studied. The raw film showed 11% water uptake but HEMA containing film showed 67%. In the soil burial test, HEMA containing shellac film was rapidly degraded than other raw, EHA and BDDA grafted films. Thermal properties indicated that grafting of acrylic monomers decreased the melting temperature of the pure shellac films.     

Valorisation of Vegetal Wastes as a Source of Cellulose and Cellulose Derivatives

Different qualities of CMC were prepared from an agricultural residue (date palm rachis) and a marine waste (Posidonia oceanica). These starting lignocellulosic materials were used as such and after chemical pulping and bleaching. The carboxymethylation reaction was carried out in presence of NaOH (40%) and monochloroacetic acid (ClCH₂COOH, MAC), in n-butanol as the reaction solvent. The substitution degrees (DS) of the obtained CMCs varied from 0.67 to 1.62 and between 0.98 and 1.86, for P. oceanica and date palm rachis, respectively. The CP-MAS ¹³C-NMR spectra of the prepared polyelectrolytes displayed the presence of the main peaks associated with cellulose macromolecules (C1–C6) and that corresponding to carboxyl functions at around 175 ppm. Unfortunately, the peak attributed to methylene groups neighbouring carboxyl moieties are overlapped by C2 and C3, which renders them hardly detectable. Nevertheless, it is worth noting that the CP-MAS ¹³C-NMR spectra revealed the presence of different signals originating from residual impurities (ca. 27 ppm), such as traces of lignin macromolecules (110–150 ppm) and methyl groups attributed to hemicelluloses. Work is in progress to establish a more efficient purification procedure, in order to have more accurate values of DS.     

Kinetics and Thermodynamics of Hydrolytic Depolymerization of Polyamide Waste at Various Temperature and Autogenious Pressure by High-Pressure Autoclave

Hydrolytic depolymerization of polyamide waste in water was studied using 0.5 L high pressure autoclave at temperatures of 235, 240, 245, 250 °C and at autogenious pressure 480, 500, 520, and 600 psi (pound per square inch).The reaction rate constant, energy of activation, enthalpy of activation, entropy of activation and equilibrium constant were calculated from the experimental data obtained. The maximum depolymerization (59.2%) of polyamide waste into monomer caprolactum was obtained at 250 °C and 600 psi pressure. The reaction rate constant was obtained on basis of measurement of amine value and residual weight. The depolymerization reaction was found to be pseudo first order with reaction rate constant of the order of 10⁻³ min⁻¹. The enthalpy, entropy and free energy of activation were recorded as 85.75, −0.1354 and 156.59 kJ mol⁻¹ respectively at the experimental conditions for maximum depolymerization of polyamide waste. The thermodynamic equilibrium constant for this hydrolysis reaction was found to be 2.3 × 10⁻¹⁶.     

Regulating the hydrolysis of organic wastes by micro-aeration and effluent recirculation

In this study, the effects of micro-aeration and liquid recirculation on the hydrolysis of vegetable and flower wastes during two-phase solid–liquid anaerobic digestion were assessed. To accomplish this, we evaluated the hydrolysis of five batches of waste that were treated under the following conditions: anaerobic, insufficient micro-aeration (aeration for 5 min every 24 h), and sufficient micro-aeration (aeration for 5 min every 12, 4 and 1 h). Hydrolysis was found to depend on the level of micro-aeration. Specifically, insufficient micro-aeration led to unstable and decreased performance. Conversely, sufficient micro-aeration promoted the hydrolysis of easily biodegradable carbohydrates and proteins, but the microbial activity was later impaired by liquid recirculation using methanogenic effluent. The hydrolysis efficiency under anaerobic conditions was comparable to the efficiency observed under sufficient micro-aeration, while the cumulative TOC of the anaerobic batch was 1.4–2.4 times higher than that of the micro-aerated batches. In addition, liquid recirculation did not have a negative effect on the development of microbial activity under anaerobic conditions, which resulted in the lignocelluloses having a higher hydrolysis efficiency.     

大块液膜法处理模拟含Cr(Ⅵ)废水

以三辛胺为载体,煤油为膜溶剂,NaOH为反萃剂,采用大块液膜法处理模拟含Cr(Ⅵ)废水.考察了Cr(Ⅵ)迁移的影响因素,实验结果表明:在料液相进水Cr(Ⅵ)质量浓度为1043.6 mg/L、料液相进水pH为1.1、反萃相中NaOH质量分数为20％、液膜相体积为100 mL、液膜相中三辛胺体积分数为15％、反应时间为50 min的条件下,料液相出水Cr(Ⅵ)质量浓度为0.5 mg/L;萃取36批废水后Cr(Ⅵ)浓缩比可达94.2％.     

Dechlorination of polyvinyl chloride in NaOH/ethylene glycol solution by microwave heating

This study investigated the dehydrochlorination of flexible polyvinyl chloride (PVC) containing 59.2% PVC, 29.7% dioctyl phthalate (DOP), and approximately 12% stabilizers. Flexible PVC was treated with NaOH/ethylene glycol (NaOH/EG) solutions at NaOH concentrations in the range 0.5–4 mol/l and was heated in a microwave heater at a temperature between 100° and 160°C for 0–30 min. All chlorides were completely eliminated by internal heating at 160°C using microwaves for 10 min in a 1 mol/l NaOH/EG solution, and the residue was made up of hydrocarbons. The weight loss rate reached a maximum of 74.7% at a temperature of 160°C. It was discovered that the use of microwaves significantly shortened the reaction time compared to using conventional electric heaters or other external heating systems and also allowed the use of lower concentrations of NaOH. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

粉煤灰制聚合氯化铝铁和白碳黑新工艺

采用粉煤灰制备聚合氯化铝铁和白碳黑.该法共分一次酸浸、碱溶、焙烧、二次酸浸4个阶段.实验确定的最佳工艺条件为:一次酸浸阶段酸溶温度100℃,碱溶阶段m(氢氧化钠):m(活化高硅渣)=0.6,二次酸浸阶段m(碳酸钠):m(灰渣A)=0.8、盐酸质量分数20%.在此条件下Fe~(3+)和Al~(3+)的总浸出率分别为96.54%和86.67%.主要产品聚合氯化铝铁的质量符合GB15892-2003<水处理剂聚氯化铝>的标准;产品白碳黑的质量符合GBl0517-89<沉淀二氧化硅>的标准.     

Effect of Solvent Composition on Porosity,Surface Morphology and Thermal Behavior of Metal Alginate Prepared from Algae (<Emphasis Type="Italic">Undaria pinnatifida</Emphasis>)

Alginates, extracted from algae are linear unbranched polymers containing β-(1→4)-linked d-mannuronic acid (M) and α-(1→4)-linked l-guluronic acid (G) residues. The conversion of alginic acid into the metal alginate is confirmed using FTIR spectroscopy. Asymmetric and symmetric stretching of free carboxyl group present in metal alginate occurs almost at the same position in various solvent compositions. Total intrusion volume of metal alginate prepared in propanol (0.0742 mL/g) is greater compared to those in ethanol (0.0648 mL/g) and methanol (0.0393 mL/g) as solvent. Surface morphology as well as porosity and pore size distribution of metal alginate are greatly influenced by solvent. It can be seen from thermal analysis results that calcium alginate prepared using different solvent compositions started decomposing at 100 °C, but rapid degradation started around 200 °C. The results showed a stepwise weight loss during thermal sweep, indicating different types of reactions during degradation. First and second step of rapid degradation was situated around 200–300 and 300–550 °C, respectively; whereas the final step is situated around 550–650 °C. The trend of degradation was similar for all the solvents, although the amount of final residue varied from one solvent to another. At the same time, lower thermal stability was also observed with higher heating rates. Additionally, a kinetic analysis was performed to fit with TGA data, where the entire degradation process has been considered as three consecutive first order reactions.     

Evaluation of landfill leachate treatment by advanced oxidative process by Fenton’s reagent combined with membrane separation system

A high content of refractory organic matter, ammonia and toxic compounds is characteristic of landfill leachate. Advanced oxidative processes (AOPs) are an attractive alternative for landfill leachate treatment. However, when applied as a unique process treatment, they do not provide a complete solution for the effluent treatment. Combining AOP with a membrane separation process (MSP) presents a number of benefits and provides an adequate solution for this problem. With this in mind, the present work aims to evaluate, using a bench scale, leachate treatability through AOP by Fenton’s reagent (AOP/Fenton) combined with microfiltration (MF) and nanofiltration (NF). A high efficient removal of COD (63%), true color (76%) and humic substances (50%) was observed during AOP/Fenton under optimized conditions (1.7 g H₂O₂/g COD_{raw leachate}; FeSO₄·7H₂O:H₂O₂ = 1:5.3; pH = 3.8; reaction conditions = 115 rpm/28 min). According to the evaluated parameters, MSP presented an efficient complementary treatment, in which the integrity of the stages was sufficient for reaching regulatory levels in the effluent (Deliberação Normativa Conjunta COPAM/CERH-MG N^o. 1, May 5, 2008).     

钛硅分子筛催化双氧水氧化水中间甲酚

探索催化双氧水氧化去除间甲酚对开发炼油厂碱渣废水处理新技术意义重大。采用钛硅分子筛催化双氧水氧化水中间甲酚,考察了反应时间、反应温度、双氧水加入量、催化剂加入量和初始溶液pH对间甲酚去除率的影响。实验结果表明：钛硅分子筛对双氧水氧化间甲酚具有显著的催化作用;在反应时间为90 min、反应温度为80 ℃、n（H₂O₂）∶n（间甲酚）为4、催化剂加入量为1.5 g/L、初始溶液pH为1.0~11.0的条件下,间甲酚去除率约为94%,间甲酚溶液的BOD₅/COD从氧化前的0.26提高到氧化后的0.38,可生化性显著提高。     

The performance of Electro-Fenton oxidation in the removal of coliform bacteria from landfill leachate

Leachate pollution is one of the main problems in landfilling. Researchers have yet to find an effective solution to this problem. The technology that can be used may differ based on the type of leachate produced. Coliform bacteria were recently reported as one of the most problematic pollutants in semi-aerobic (stabilized) leachate. In the present study, the performance of the Electro-Fenton process in removing coliform from leachate was investigated. The study focused on two types of leachate: Palau Borung landfill leachate with low Coliform content (200 MPN/100 m/L) and Ampang Jajar landfill leachate with high coliform content (>24 × 10⁴ MPN/100 m/L). Optimal conditions for the Electro-Fenton treatment process were applied on both types of leachate. Then, the coliform was examined before and after treatment using the Most Probable Number (MPN) technique. Accordingly, 100% removal of coliform was obtained at low initial coliform content, whereas 99.9% removal was obtained at high initial coliform content. The study revealed that Electro-Fenton is an efficient process in removing high concentrations of pathogenic microorganisms from stabilized leachate.     

Rapid estimation of compost enzymatic activity by spectral analysis method combined with machine learning

The aim of this study was to investigate the feasibility of using visible near-infrared (VisNIR) diffuse reflectance spectroscopy (DRS) as an easy, inexpensive, and rapid method to predict compost enzymatic activity, which traditionally measured by fluorescein diacetate hydrolysis (FDA-HR) assay. Compost samples representative of five different compost facilities were scanned by DRS, and the raw reflectance spectra were preprocessed using seven spectral transformations for predicting compost FDA-HR with six multivariate algorithms. Although principal component analysis for all spectral pretreatments satisfactorily identified the clusters by compost types, it could not separate different FDA contents. Furthermore, the artificial neural network multilayer perceptron (residual prediction deviation = 3.2, validation r² = 0.91 and RMSE = 13.38 μg g^?1 h^?1) outperformed other multivariate models to capture the highly non-linear relationships between compost enzymatic activity and VisNIR reflectance spectra after Savitzky–Golay first derivative pretreatment. This work demonstrates the efficiency of VisNIR DRS for predicting compost enzymatic as well as microbial activity.     

1,3-Propanediol Production Potential by a Locally Isolated Strain of Klebsiella Pneumoniae in Comparison to Clostridium Beijerinckii NRRL B593 from Waste Glycerol

The fermentative production of 1,3-propanediol (1,3-PDO) by Klebsiella pneumoniae under different initial substrate concentrations (between 5 and 110 g/L) was investigated. It was found that glycerol was almost 100% utilized and 1,3-PDO production increased up to 20 g/L of influent substrate concentration, but there was a significant decrease in both glycerol consumption and 1,3-PDO production at substrate concentrations exceeding 20 g/L. Furthermore, pH control was essential, and a lack of pH control negatively effects of 1,3-PDO production. In the second part of the study, two microorganisms, namely Clostridium beijerinckii NRRL B593 and K. pneumoniae were comparatively studied in terms of their 1,3-PDO productivity under pH controlled conditions. Higher 1,3-PDO production was achieved under pH controlled fermentation conditions (pH = 7) for both microorganisms. Even though the two microorganisms had almost the same 1,3-PDO yield (0.60 mol/mol for C. beijerinckii, 0.61 mol/mol for K. pneumoniae) at the end of fermentation period, K. pneumoniae completed the 1,3-PDO production in one-third of the time (t = 8 h with a productivity of 1.34 g/L/h) than C. beijerinckii (t = 24 h). The results of this study clearly indicated that a substrate inhibition is a challenge that needs to be studied further for higher productivities.