Compositions and greenhouse gas emission factors of flared and vented gas in the Western Canadian Sedimentary Basin

A significant obstacle in evaluating mitigation strategies for flaring and venting in the upstream oil and gas industry is the lack of publicly available data on the chemical composition of the gas. This information is required to determine the economic value of the gas, infrastructure and processing requirements, and potential emissions or emissions credits, all of which have significant impact on the economics of such strategies. This paper describes a method for estimating the composition of solution gas being flared and vented at individual facilities, and presents results derived for Alberta, Canada, which sits at the heart of the Western Canadian Sedimentary Basin. Using large amounts of raw data obtained through the Alberta Energy Resources Conservation Board, a relational database was created and specialized queries were developed to link production stream data, raw gas samples, and geography to create production-linked gas composition profiles for approximately half of the currently active facilities. These were used to create composition maps for the entire region, to which the remaining facilities with unknown compositions were geographically linked. The derived data were used to compute a range of solution gas composition profiles and greenhouse gas emission factors, providing new insight into flaring and venting in the region and enabling informed analysis of future management and mitigation strategies.

Implications: Accurate and transparent determination of environmental impacts of flaring and venting of gas associated with oil production, and potential benefits of mitigation, is severely hampered by the lack of publicly available gas composition data. In jurisdictions within the Western Canadian Sedimentary Basin, frameworks exist for regulating and trading carbon offset credits but current potential for mitigation is limited by a lack of standardized methods for calculating CO₂ equivalent emissions. The composition and emission factor data derived in this paper will be useful to industry, regulators, policy researchers, and entrepreneurs seeking statistically significant and openly available data necessary to manage and mitigate upstream flaring and venting activity and estimate greenhouse gas impacts.     

Structural and sensing properties of ethanol gas using Pd-doped SnO2 thick film gas sensor

Environmental Science and Pollution Research - In the present study, we fabricate undoped and 1 wt% palladium (Pd)-doped tin oxide (SnO2) films were deposited on alumina substrate using...     

Understanding oil and gas pneumatic controllers in the Denver–Julesburg basin using optical gas imaging

ABSTRACT

In the spring of 2018, a 10-day field study was conducted in Colorado’s Denver-Julesburg oil and natural gas production basin to improve information on well pad pneumatic controller (PC) populations and identify PCs with potential maintenance issues (MIs) causing excess emissions through a novel optical gas imaging (OGI) survey approach. A total of 500 natural gas-emitting PCs servicing 102 wells (4.9 PCs/well) were surveyed at 31 facilities operated by seven different companies. The PCs were characterized by their designed operational function and applications, with 83% of the PC population identified as intermittent PCs (IPCs). An OGI inspection protocol was used to investigate emissions on 447 working PCs from this set. OGI detected continuous emissions from 11.3% of observed IPCs and these were classified as experiencing some level of MIs. OGI imaging modes were observed to have a significant effect on emission detectability with high sensitivity mode detection rates being approximately 2 times higher compared to auto mode. Fourteen snapshot emission measurements (not including actuations) were conducted on IPCs in this category using a high-volume sampling device with augmented quality assurance procedures with observed emissions rates ranging from 0.1 up to 31.3 scf/hr (mean = 2.8 scf/hr). For PCs with continuous depressurization type (CPC), 36.8% had continuous emissions observed by OGI. Four supporting emission measurements were conducted on CPCs with one unit exceeding the low bleed regulatory emission threshold with an emission rate of 9.9 scf/hr (mean = 4.2 scf/hr). Additional information was collected on PC actuation events, as observed with OGI, which showed a strong correlation between observed actuation events and facility production compared to observed continuous emissions caused by MIs which did not correlate with facility production.

Implications: A novel survey approach of pneumatic controllers at oil and natural gas production facilities in the Denver-Julesburg basin, using optical gas imaging and supporting emission measurements, was demonstrated as an effective method to identify controllers with potential maintenance issues causing excess emissions. The results of the pneumatic controller and optical gas imaging surveys improved information on pneumatic controller populations within the basin and also demonstrated the significant effect optical gas imaging modes have on emission detections.     

基于Aspen Plus软件的生物质气与煤混合燃烧烟气排放特性计算分析

为了分析生物质气与煤混合燃烧对烟气排放特性的影响,基于Aspen Plus软件,搭建了生物质气与煤混合燃烧模型,对混合燃烧产物进行模拟计算。在生物质气化过程中,随着空燃比的增加,生物质气的低位热值先升高后降低。选取低位热值最高时的生物质气和煤在不同生物质掺烧比例下混合燃烧。随着生物质掺烧比例从0%增加到30%,在保证混合燃烧的理论空气量条件下,炉膛燃烧温度逐渐下降,烟气排放特性也随之变化。在掺烧比例达到30%时,SO_2的体积分数降低了30%左右,H_2O的体积分数增加了26.7%~39.2%,烟气排放量增加了2.38%~3.2%。随着生物质掺烧比例的增加,混合燃烧对锅炉运行造成的影响逐渐增大。     

铝箔复合膜集气袋对有机废气的适用性研究

通过在不同的时间段,测定存放于铝箔复合膜集气袋和玻璃注射器的丙酮,醋酸乙酯,苯,异丙醇标准气的浓度,气体浓度与贮存时间的关系,本次试验结果表明,丙酮,醋酸乙酯,苯,异丙醇在铝箔气袋中的稳定性明显优于在玻璃注射器中,应尽可能在８－２４ｈ内测定。     

Identification of odorous compounds in air and gas from painting and printing industries by gas chromatography-mass spectrometry and library search system

A computer-assisted library search system is described consisting of a data base, pre-search and main search. Odorous air and effluent gas from painting and printing industries were analyzed by gas chromatography-mass spectrometry and the library search system. Main components were 2-methylpropanol, three xylenes, toluene, ethyl acetate and butyl acetate.     

利用活性炭纤维有机废气吸附回收装置治理二氯甲烷废气

文章介绍了一种化工生产过程中排出的二氯甲烷废气的治理装置———活性炭纤维有机废气吸附回收装置和治理工艺。由于采用了优越的吸附材料和先进的工艺设计 ,使吸附回收率达 97%以上 ,收到了很好的环境效益和经济效益     

聚丙烯腈基活性碳纤维用于烟气脱硫脱硝

应用聚丙烯腈基活性碳纤维(PAN-ACF)对模拟的工业烟气中的SO2和NO在烟气露点温度以上进行吸附脱除实验。通过改变固定床ACF装载量、反应温度、水蒸气体积分数和O2体积分数,研究了ACF脱硫效率和脱硝效率的变化规律,还研究了同时脱硫脱硝时入口SO2或NO浓度对脱除效率的影响。结果表明:PAN-ACF具有良好的脱硫性能和一定的脱硝能力,其脱硫效率和脱硝效率随着ACF装载量和O2体积分数的增大而升高,随着温度的升高而降低,随着水蒸气体积分数的增大先升高后降低;在同时脱硫脱硝时,SO2对ACF的脱硝反应有明显的抑制作用,而NO对ACF的脱硫反应影响不大。     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in plywood combustion gas

Polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/DF) levels in plywood combustion gas were investigated for the effects of ammonium chloride (NH4Cl) and paint. For combustion systems in which neither NH4Cl nor paint were present in the plywood samples, total amounts of PCDD/DFs in the combustion gas were in the order of 35-529 ng/Nm3, and were higher in the systems with softwood trees than broadleaf ones, depending on the Cl concentrations. For the systems with added NH4Cl and no paint, and those without NH4Cl but were painted, higher PCDD/ DF rates were observed at combustion temperatures of 270 degrees C and 500 degrees C, respectively. However, for the systems with both NH4Cl and paint, their amounts in the range of 0.6-13 ng/Nm3 were the lowest in all systems. The PCDD/DF abundance profiles were similar to their patterns in pentachlorophenol (PCP). Furthermore, it was found that the 2,3,7,8-chlorine substituted penta- and hexa-CDDs contributed more than other 2,3,7,8-chlorine substitutes to toxicity equivalency (TEQ).     

煤气发生炉炉渣改性和吸附性能

以工业中生产煤气时产生的煤气炉炉渣为原料,采用手工分选法将炉渣中的炭及残渣分离,再采用酸碱浸渍方法对炉渣残渣进行改性,研究了改性后的炉渣残渣及炉渣中分离出的炭对溶液中苯酚的吸附性能。吸附实验结果表明,分离炭的吸附性能最好,其次为碱改性炉渣残渣和酸改性炉渣残渣,未改性炉渣残渣吸附性能最差。改性的炉渣残渣及分离炭对苯酚吸附过程符合二级吸附动力学模型。吸附等温线研究表明,改性炉渣残渣及分离炭对苯酚的吸附符合Lang-muir吸附等温式。     

湿法烟气脱硫工艺中烟气再热方式的选择

分析了湿法烟气脱硫烟气再热原因,介绍了多种烟气再热方法,并对其进行了技术分析,为湿法烟气脱硫工程的烟气再热系统设计提供了依据。     

Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.     

Greenhouse gas induced climate change

Simulations using global coupled climate models predict a climate change due to the increasing concentration of greenhouse gases and aerosols in the atmosphere. Both are associated with the burning of fossil fuels. There has been considerable debate if this postulated human influence is already evident. This paper gives an overview on some recent material on this question. One particular study using optimal fingerprints (Hegerl et al., 1996) is explained in more detail. In this study, an optimal fingerprint analysis is applied to temperature trend patterns over several decades. The results show the probability being less than 5% that the most recently observed 30 year trend is due to naturally occurring climate fluctuations. This result suggests that the present warming is caused by some external influence on climate, e.g. by the increasing concentrations of greenhouse gases and aerosols. More work is needed to address the uncertainties in the magnitude of naturally occurring climate fluctuations. Also, other external influences on climate need to be investigated to uniquely attribute the present climate change to the human influence.     

石墨气体扩散电极的制备与性能优化

电极的制备工艺及参数直接影响电极材料的活性。主要考察了C/PTFE质量比、碾压压力、煅烧温度、造孔剂NH4HCO3及稀土掺杂等因素对电极产出H2O2的影响规律。研究结果表明,电极最佳制备条件为:石墨和PTFE质量比为2∶1、石墨、造孔剂和稀土元素质量比为6∶1∶1、碾压压力10 MPa、煅烧温度330℃。在pH=3、电解质Na2SO4浓度为0.05mol/L条件下,电解2 h后,改性电极产生的H2O2从95 mg/L提高到350 mg/L,提高了268.4%。