Formation of polychlorobiphenyls in silicone rubber

In silicone rubber crosslinked with bis(2,4-dichlorobenzoyl) peroxide (DCBP) as initiator about 0.1% of DCBP is converted into polychlorobiphenyls (PCBs). The PCB content in silicone rubber determined by high resolution gas chromatography (HRGC) after its destruction by HF is around 10 mg/kg. 29 PCB congeners were detected. Instead of the expected PCB-47, lower chlorinated congeners are predominant. Some possible pathways of their origin are presented.     

Determination of polychlorobiphenyls in Venice Lagoon sediments

Polychlorinated biphenyl (PCBs) congeners were measured in 14 sediment samples collected at five sites in the Venice Lagoon selected on the basis of a supposed diversity of inputs and of pollution levels. The PCBs were determined after a sonication assisted extraction by gas chromatography mass spectrometry (GCMS). The sum of the congener concentrations determined in the samples range from 4.05 to 239.15 ng/g on a dry weight basis. The concentration values are very variable both comparing the sites and comparing different samples from the same site and can be connected to the sand percentage in the sediment samples. The correlation matrix obtained from data matrix using the congener concentrations as variables shows high values, mostly between 0.964 and 1, suggesting that the pattern of the PCB congeners and the ratios among the concentrations in Venice Lagoon sediments are more or less constant; the samples differ only in the concentration level.     

Thermal desorption of polychlorobiphenyls from contaminated soils and their hydrodechlorination using Pd- and Rh-supported catalysts

This paper reports about a combined technology for soil remediation from PCBs using the thermal desorption technique coupled with the catalytic hydrogenation of recovered PCBs. The reactor is a bench scale rotating desorption furnace through which nitrogen is flushed and used as carrier gas of desorbed PCBs. The latter are condensed into an hexane or hexane-acetone (1:1 v/v) solution that is then hydrogenated using phosphate-supported Pd or Rh as catalyst. The analysis of the treated soil, under variable operative conditions (temperature and desorption time), shows that the total (99.8%) decontamination from PCBs occurs. The recovery yield of the desorbed PCBs is better than 75% and the subsequent hydrogenation reaches 63% of the collected PCBs in 5h or 100% in 12h.     

Determination of levels of polychlorinated biphenyl in transformers oil from some selected transformers in parts of the Greater Accra Region of Ghana

Although polychlorinated biphenyls have never been manufactured in Ghana, it has been used extensively as dielectric fluid in electric transformers and capacitors. However, very little is known of its health and environmental impacts by both managers of these transformers and capacitors and also the general public. This work therefore seeks to explore INAA as a possible alternative to screening transformer oils for PCBs by determining the total chlorine content. The total chlorine content of transformer oil samples from Ghana that tested positive and some randomly selected samples that tested negative from screening using CLOR-N-OIL test kits, have had their total chlorine estimated. INAA using the Research Reactor located at the Ghana Atomic Energy Commission was used to estimate the total chlorine content of the oil samples. Neutron Activation and gamma ray spectroscopy using HPGe detector coupled to MAESTRO 32 software was used to determine the total chlorine content by integrating the peak area of the spectrum into a simplified program that was developed from the activation equation. Instrumental Neutron Activation Analysis was able to validate the result obtained from the test kits screening with accuracy 7.5%.The minimum total chlorine content of the positive samples determined by NAA was 71.34 μg g⁻¹.     

Assessment of polychlorobiphenyls in human/poultry fat and in hair/plumage from a contaminated area

HR gas chromatographic PCB patterns in human/poultry fat tissue and hair/plumage in samples from a polluted region of Bela Krajina /Slovenia/ were investigated. The concentration of PCBs in human adipose tissue was found to be 9.62 μg/g in comparison to 0.67 μg/g in the adipose tissue of the non-exposed population, and in poultry fat 12.80 μg/g on a fat basis. The corresponding values in human hair and poultry plumage were 0.90 μg/g and 0.20 μg/g of original weight. The difference in PCB patterns between fat and hair can be attributed to the different routes of contamination (ingestion, air transport), to the time of exposure and physicochemical properties (octanol- water partition coefficients, Henry's law constants and the metabolism) of some individual congeners. Hair could be used for the assessment of ingestion of contaminated food and of the PCB levels in the air. In fat tissue PCB congeners with higher metabolic stability are enriched, whereas in hair PCB congeners with higher concentrations in air and with high octanol- water partition coefficients predominate.     

Increased levels of polychlorobiphenyls in Italian women with endometriosis

Endometriosis has been hypothesised to be linked to persistent and toxic organochlorinated chemicals. Dioxins and dioxin-like compounds have in particular been associated with the disease, mainly on the basis of experimental studies. Data in women are conflicting. A case-control study on 80 Italian nulliparous women of reproductive age was carried out to assess whether there is a correlation between the presence of endometriosis and blood levels of polychlorobiphenyls (PCBs), a family of ubiquitary environmental pollutants which comprises congeners with dioxin-like activity. Higher levels of PCBs were found in women with endometriosis. A mean cumulative value of 410 ng g(-1), lipid base, was found in cases versus the value of 250 ng g(-1) observed in the control group (odds ratio for upper tertile 4.0, CI 95% 1.3-13; p = 0.0003). PCB increase involved both dioxin-like (PCBs 105, 118, 156, and 167) and non-dioxin-like congeners (PCBs 101, 138, 153, 170, 180).     

Relative bioavailability to laying hens of indicator polychlorobiphenyls present in soil

Transfer of indicator polychlorobiphenyls (PCBs) from soil into hen eggs may occur in hens reared outdoor, which ingest significant amounts of soil. This transfer depends on the bioavailability of the ingested compounds. The impact of soil on the bioavailability of indicator PCBs was assessed by means by a relative bioavailability (RBA) trial, in which their deposition in egg yolk and in abdominal fat, in response to their ingestion through contaminated-soil and through spiked-oil were compared. A sandy soil (709 μg indicator PCBs kg⁻¹ dry matter) was collected in the vicinity of a former fire involving treated wood. Twenty-eight laying hens were individually housed and fed one of the seven experimental diets during 14 d. The seven experimental diets were an uncontaminated control diet, three diets in which contaminated soil was introduced at levels of 3%, 6% and 9% and three diets in which spiked oil was introduced to achieve similar levels and profile of contaminants. Yolk, abdominal fat and liver were collected at the end of exposure. Indicator PCBs were extracted by ASE (Accelerated Solvent Extraction) and analyzed by GC-HMRS. Within each ingested matrix, the concentration of indicator PCBs in yolk and in abdominal fat linearly increased with the amount of indicator PCB ingested (P < 0.001). Except for PCB 28, the slopes of the responses to soil and to oil could not be differentiated (P > 0.1). RBA estimates did not differ from 1 for all indicator PCBs except for PCB 28, for which it was 0.58-0.59. Measurements performed on liver confirm these conclusions.     

Biomimetic chemical degradation of polychlorobiphenyls below 100°C

PCBs were rapidly degraded by hydroxy radicals formed in the biomimetic degradation systems of superoxide, ferric chloride, and hydrogen peroxide at high concentrations below 100°C. The degradation rates of Kanechlor KC 300, KC 400, KC 500 and KC 600 were 95.4%, 89.1%, 59.9% and 47.9%, respectively. The generation of carbon dioxide gas was recognized and chloride ion showed 89.9 – 102.7% of the theoretical yield in the degradation of KC 300, KC 400 and KC 500.     

Sensitized photodegradation of adsorbed polychlorobiphenyls (PCB's)

Polychlorobiphenyls (PCB's) adsorbed on silica gel or montmorillonite were degraded mainly to less chlorinated biphenyls by U.V. irradiation (λ = 254 nm). The photodegradation was considerably enhanced by adding triethylamine to the system. The sensitizing effect can be ascribed, like in solution, to the formation of a charge-transfer complex confirmed by fluorescence quenching experiments.     

Review of recently used adsorbents for antimony removal from contaminated water

Environmental Science and Pollution Research - As prior pollutants, antimony (Sb) and its compounds are carcinogenic to threaten human health. With the development of the industry, various...     

Synthesis of methylthio- and methylsulfonyl-polychlorobiphenyls via nucleophilic aromatic substitution of certain types of polychlorobiphenyls

A one-step preparation of some methylthiopolychlorobiphenyls from methanethiolate in methanol and certain chlorinated biphenyls is described. Two of the methyl sulfides and one bis(methyl-thio)tetrachlorobiphenyl are characterized in some detail. The methylthiopolychlorobiphenyls were oxidized by use of hydrogen peroxide in acetic acid to give five methylsulfonylpolychlorobiphenyls which are characterized by melting point, elemental analysis, UV-absorption (Table 1), ¹H NMR (Table 2) and mass spectrometry (Table 3). By use of the method presented a mixture of methyl sulfides derived from a technical mixture of polychlorinated biphenyls (PCB) were prepared as well as the corresponding mixture of methyl sulfones. Additionally the same synthetic method was used for the preparation of methyl sulfides and methyl sulfones derived from two ¹⁴C-labelled polychlorobiphenyls.     

Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

固态发酵法制备优势硝化菌固定化产品的工艺优化

为解决高效菌在工程应用中扩大培养、保存和接种等瓶颈,研究固态发酵法制备焦化废水优势硝化菌固定化产品.以TTC脱氢酶活性法作为固体发酵生物量测定指标,通过液态发酵单因素实验初步确定硝化菌发酵条件,再用响应面法对其固态发酵条件进行优化.结果表明,TTC脱氢酶活性法适合作为表征生物质载体固定化产品生物量的测定方法,不受载体和培养时间的影响,能较好地指示干燥前固态发酵生物量的变化.固态发酵主要影响参数依次为发酵时间、发酵温度、接种量和含水率.发酵时间的最佳值为47 h,发酵温度最佳为29.4℃,接种量的最佳值为9.9 mL/200 mL,最佳含水率为48.9％时,固态发酵固定化产品酶活达到17.091 μg TF/(g·h).与液态发酵参数相比其发酵温度、接种量最佳值接近,但发酵时间由1d延长至2d,产品酶活持平.     

Organic compound emissions from a landfarm used for oil and gas solid waste disposal

Solid or sludgy hydrocarbon waste is a by-product of oil and gas exploration and production. One commonly used method of disposing of this waste is landfarming. Landfarming involves spreading hydrocarbon waste on soils, tilling it into the soil, and allowing it to biodegrade. We used a dynamic flux chamber to measure fluxes of methane, a suite of 54 nonmethane hydrocarbons, and light alcohols from an active and a remediated landfarm in eastern Utah. Fluxes from the remediated landfarm were not different from a polytetrafluoroethylene (PTFE) sheet or from undisturbed soils in the region. Fluxes of methane, total nonmethane hydrocarbons, and alcohols from the landfarm in active use were 1.41 (0.37, 4.19) (mean and 95% confidence limits), 197.90 (114.72, 370.46), and 4.17 (0.03, 15.89) mg m^?2 hr^?1, respectively. Hydrocarbon fluxes were dominated by alkanes, especially those with six or more carbons. A 2-ha landfarm with fluxes of the magnitude we observed in this study would emit 95.3 (54.3, 179.7) kg day^?1 of total hydrocarbons, including 11.2 (4.3, 33.9) kg day^?1 of BTEX (benzene, toluene, ethylbenzene, and xylenes).

Implications: Solid and sludgy hydrocarbon waste from the oil and gas industry is often disposed of by landfarming, in which wastes are tilled into soil and allowed to decompose. We show that a land farm in Utah emitted a variety of organic compounds into the atmosphere, including hazardous air pollutants and compounds that form ozone. We calculate that a 2-ha landfarm facility would emit 95.0 ± 66.0 kg day^?1 of total hydrocarbons, including 11.1 ± 1.5 kg day^?1 of BTEX (benzene, toluene, ethylbenzene, and xylenes).     

活性污泥法处理味精厂废水的工艺优化

经过总结与改进武汉味全食品有限公司近 5年污水处理工艺、设备 ,结果表明 ,经过增加三级曝气池、罗茨鼓风机等工艺改进 ,SS由 132mg/L降为 112mg/L ;NH3 N由 119mg/L降为 37 6mg/L ;Ar OH由 0 0 1mg/L降为 0 0 0 9mg/L ;BOD5由 5年前的 34 6mg/L降为现在的 2 1 2mg/L ;COD由 5年前的 117mg/L降为现在的 6 2 6mg/L ;运行成本由 85 0万降到 4 5 0万 ,通过此工艺的改进及优化 ,基本达到国家污水排放标准 ,完全达到行业排放标准     

Gaseous emissions from outdoor concrete yards used by livestock

Measurements of ammonia (NH₃), nitrous oxide (N₂O) and methane (CH₄) were made from 11 outdoor concrete yards used by livestock. Measurements of NH₃ emission were made using the equilibrium concentration technique while closed chambers were used to measure N₂O and CH₄ emissions. Outdoor yards used by livestock proved to be an important source of NH₃ emission. Greatest emission rates were measured from dairy cow feeding yards, with a mean of 690 mg NH₃-N m⁻² h⁻¹. Smaller emission rates were measured from sheep handling areas, dairy cow collecting yards, beef feeding yards and a pig loading area, with respective mean emission rates of 440, 280, 220 and 140 mg NH₃-N m⁻² h⁻¹. Emission rates of N₂O and CH₄ were much smaller and for CH₄, in particular, emission rates were influenced greatly by the presence or absence of dung on the measurement area.