A portable fiber-optic chemical device for the quantitative determination of carbon monoxide from automobile exhaust emissions

A colorimetric method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H8Si[Mo2O7]6). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.     

A Portable Fiber-Optic Chemical Device for the Quantitative Determination of Carbon Monoxide from Automobile Exhaust Emissions

ABSTRACT

A colorimetxic method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H₈Si[Mo₂O₇]₆). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.¹     

A rapid spectrophotometric determination of persulfate anion in ISCO

Due to a gradual increase in the use of persulfate as an in situ chemical oxidation (ISCO) oxidant, a simple measurement of persulfate concentration is desirable to analyze persulfate distribution at designated time intervals on/off a site. Such a distribution helps evaluate efficacy of ISCO treatment at a site. This work proposes a spectrophotometric determination of persulfate based on modification of the iodometric titration method. The analysis of absorption spectra of a yellow color solution resulting from the reaction of persulfate and iodide in the presence of sodium bicarbonate reveals an absorbance at 352 nm, without significant interferences from the reagent matrix. The calibration graph was linear in the range of persulfate solution concentration of 0-70 mM at 352 nm. The proposed method is validated by the iodometric titration method. The solution pH was at near neutral and the presence of iron activator does not interfere with the absorption measurement. Also, analysis of persulfate in a groundwater sample using the proposed method indicates a good agreement with measurements by the titration method. This proposed spectrophotometric quantification of persulfate provides a simple and rapid method for evaluation of ISCO effectiveness at a remediation site.     

A Rapid and Sensitive Colorimetric Reagent for Nitrogen Dioxide in Air

High speed instrumentation requires a colorimetric reagent capable of detecting traces of nitrogen dioxide with little delay for color development. Rate of color development and sensitivity of Griess-type reagent have been improved by adding a promoter (R-salt) and optimizing the concentrations of diazotizing and coupling reagents. Field tests show that the new instrument-reagent combination can resolve short-duration peaks in NO₂ concentrations of 5 to 10 pphm.     

对氯气校正法测定高氯废水化学需氧量的方法研究

氯气校正法(HJ/T70-2001)是测定高氯废水化学需氧量的国标方法,为了减少样品测定过程带来的环境污染,研究在不改变HJ/T70-2001氧化体系及测试条件的情况下,将取样体积由20 mL减半为10 mL,试剂的使用量相应减半,对方法的检出限、相对误差、相对标准偏差等指标进行验证。结果表明,该方法的检出限符合要求,准确度较高,精密度较好,可用于高氯废水化学需氧量的测定。     

液-液萃取处理高氯难降解有机废水

农药化工厂生产苯肼、苯唑醇、乙基氯化物过程排放的废水是高氯难生物降解有机废水,采用三辛胺作萃取剂,用液-液萃取处理,三辛胺与水中Cl-离子形成萃合物而使Cl-转移到有机相.再经高效絮凝处理后,CODCr总去除率达89.8%,Cl-总去除率达83.2%,BOD/COD比从0.02上升到0.34,可生化性大幅度提高. 废水再经河水稀释进A/O池生化处理3d后,可达标排放.负载萃取液用5%NaOH水溶液反萃取.由于萃取剂回用降低了处理费用.     

自配消解液分光光度法测定污水中的COD

以自配消解液代替ThermoFisher公司AQ4001COD测定系统的专用消解液,比较了自配消解液分光光度法与国家标准重铬酸钾法(GB 11914-1989)测定化学需氧量(COD)的差异。对比试验表明,自配消解液分光光度法测定COD的结果精确度和准确度高,与国家标准方法无显著性差异。自配消解液分光光度法测定水样COD值的相对标准偏差;低量程(30～150 mg/L)为1.38%～2.53%,中量程(0～1 500 mg/L)为0.47%～3.63%,高量程（2 000～15 000 mg/L）为0.17%～3.53%,在国家标准方法测试水样COD值的允许误差范围内。除制革废水外,自配消解液可以代替AQ4001COD测定系统的专用消解液,适用不同量程范围内污水COD的测定。自配消解液分光光度法具有试剂使用量少、速度快、经济、二次污染小等优点,值得在环境科学领域及废水水质监测中推广应用。     

Public Health Service National Fallout Surveillance Program

A semi-automated method for determination of fluorine in biological materials has been developed incorporating the Technicon AutoAnalyzer. One-half gram of dried, ground plant material is ashed, alkali-fused, diluted with water, and the suspension is pumped, along with H₂SO₄, at controlled rates, into the hot revolving glass helix of a digestor unit. As the acid-digest mixture passes through the heated coil, volatile fluoride and water vapor are evolved. The volatile fluoride and water vapor are pulled from the helix under reduced pressure through a tube which projects into the helix. The tube, in turn, is connected to a water-jacketed condenser and then to an impinger where the sample is continuously mixed. An aliquot of the impinger liquid is being constantly withdrawn. This sample is then air-segmented and mixed with a reagent containing alizarin complexone, pH 4 acetate buffer, lanthanum nitrate, acetone, and water. The sample-reagent combination passes through 4 full-length mixing coils where color development takes place. Upon reacting with fluoride, the wine-red alizarin complexone-La(III) reagent forms a lilac blue fluoride complex. The solution is pumped from the mixing coils through the tubular flow cell of the colorimeter. The absorbence of the solution is measured at 624 mμ, and the signal is transmitted to a recorder where the results are plotted on absorbency paper. The absorbence at the apex of the peak is proportional to the amount of fluoride in the sample between the range of 2.5-80 μg °F. Samples are analyzed at a rate of 12 per hour. Results compare favorably with those obtained by Willard-Winter distillation. Recent studies indicate that the F content of plant tissues can be estimated without prior ashing and fusion     

酪氨酸氯化过程中光谱变化特征及消毒副产物的生成规律

考察酪氨酸在不同投氯量条件下氯化后的余氯,紫外吸光度值和荧光光谱,以及消毒副产物对羟基苯乙腈(4-HBC)的生成特性。结果表明,随着投氯量的增加,余氯呈现先增加再减小再增加的趋势。在投氯量为0～0.5 mmolCl2/L时,增加投氯量可提高氯化后溶液的UV254、UV274和UV280值以及4-HBC的生成量,表明低投氯量时氯化可提高溶液中不饱和键的含量;而投氯量为0.5～1 mmol Cl2/L时,增加投氯量降低UV254、UV274和UV280值以及4-HBC的生成量,表明过量的氯亦可破坏溶液中的不饱和键。荧光光谱测试实验亦发现:在投氯量为0.05 mmol Cl2/L时,酪氨酸溶液氯化后的荧光峰强度明显增加,表明氯化可生成荧光强度较高的产物。过量的氯(0.5～1 mmol Cl2/L)则可破坏溶液中的荧光结构,降低荧光峰强度直至未检出。     

活性炭吸附化学战剂--沙林染毒水的试验研究

研究了 5种国产活性炭吸附水中沙林的性能及影响因素。果壳质活性炭的吸附性能优于煤质活性炭。果壳活性炭WP 2 0 2的吸附等温线方程为 qe=11 45C0 39e ,其粉状炭在 10min时能达到吸附容量的 98%。活性炭颗粒小则吸附速度快 ,温度升高不利于吸附。活性炭与水中的氯反应后 ,吸附性能下降 3 0 % ,在含盐量 2 0 0 0mg/L的苦咸水中吸附量降低 5 %。处理化学战剂 -沙林染毒水宜多种水处理技术相结合 ,并采用活性炭吸附作为最后一级处理单元     

Contribution of free radicals to chlorophenols decomposition by several advanced oxidation processes

The chemical decomposition of aqueous solutions of various chlorophenols (4-chlorophenol (4-CP), 2,4-dichlorophenol (2-DCP), 2,4,6-trichlorophenol (2,4,6-TCP) and 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP)), which are environmental priority pollutants, is studied by means of single oxidants (hydrogen peroxide, UV radiation, Fenton's reagent and ozone at pH 2 and 9), and by the Advanced Oxidation Processes (AOPs) constituted by combinations of these oxidants (UV/H2O2 UV/Fenton's reagent and O3/UV). For all these reactions the degradation rates are evaluated by determining their first-order rate constants and the half-life times. Ozone is more reactive with higher substituted CPs while OH* radicals react faster with those chlorophenols having lower number of chlorine atoms. The improvement in the decomposition levels reached by the combined processes, due to the generation of the very reactive hydroxyl radicals. in relation to the single oxidants is clearly demonstrated and evaluated by kinetic modeling.     

Fenton''s type reaction and chemical pretreatment of PCBs

This study evaluates the effects of Fenton's reagent (FR) on the rate and extent of the oxidative degradation of individual mono, di-, tri- and tetrachlorobiphenyls in the commercial mixture DELOR 103, equivalent to AROCLOR 1248. The oxidation effect of FR strongly increased with increasing the molar ratio of Fe²⁺/H₂O₂. The most effective oxidation of DELOR 103 (10 μg.ml⁻¹) was achieved in a solution containing 1M H₂O₂ and 1 mM Fe²⁺. The FR elimination rate constants of PCB congeners decrease with increasing number of chlorine substituents in the biphenyl molecule and show a good correlation with the values of molecular weights of the PCB congeners and their 1-octanol/water partition coefficients.     

Fenton氧化活性深蓝染料B-2GLN的动力学

为了考查H2O2/Fe2+的摩尔比和H2O2的初始剂量、pH值以及活性深蓝染料B-2GLN(RDB B-2GLN)的初始浓度对活性深蓝染料B-2GLN降解过程的影响,采用在线分光光度法对活性深蓝染料B-2GLN的Fenton氧化过程进行了研究,探讨了其动力学过程,并利用气相色谱-质谱联用分析降解中间产物。结果显示,采用Fenton氧化降解水溶液中活性深蓝染料B-2GLN,在H2O2的剂量为2.635 mmol/L,pH值为2.7,H2O2/Fe2+的摩尔比为37.80和活性深蓝染料B-2GLN的初始浓度16 mg/L的条件下,得到300 s后活性深蓝染料B-2GLN的最大色度去除率为85.04%。水溶液中活性深蓝染料B-2GLN与·OH的反应速率常数为2.62×1011L/(mol·s)。活性深蓝B-2GLN染料的分子结构被Fenton试剂分解而未被完全矿化,同时对活性深蓝染料降解产物进行了分析。在线分光光度法是研究染料色度去除率的一种精确、快速与可行的方法。     

Dechlorination pathways of ortho-substituted PCBs by UV irradiation in n-hexane and their correlation to the charge distribution on carbon atom

The photodegradations of 22 individual polychlorinated biphenyl (PCB) congeners (including 21 non-coplanar ortho substituted and one non-ortho substituted) by irradiation with ultraviolet lamp in n-hexane solution were studied. Photoproducts were identified by matching their retention times and mass spectra with those of authentic standards. PCB congener with less than two chlorides was photodegraded within half an hour, if more than three chlorine on ring, the photodechlorination time for PCB needs one and half hours or more, sometimes even longer than 15 h. The half-life of PCB degradation by photodechlorination was much shorter than that by anaerobic biological dechlorination. Charge distribution on carbon atom combined with the monitoring products of individual PCB congeners were used to deduce the photodegradation pathways. The higher the charge distribution for carbon to which chlorine is attached, the easier for photodechlorination to occur. A lot of chlorine atoms attached PCB, the dechlorination was found to occur prior to the carbon with higher charge distribution at the benzene ring with more chlorine atoms attached.     

Photodegradation of an azo dye of the textile industry

An advanced oxidation treatment, UV/H2O2, was applied to an azo dye, Hispamin Black CA, widely used in the Peruvian textile industry. Rates of color removal and degradation of the dye have been evaluated. A strongly absorbing solution was completely decolorized after 35 min of treatment, and after 60 min an 82% reduction of the total organic carbon (TOC) was obtained. It has been found that the degradation rate increased until an optimum value, beyond which the reagent exerted an inhibitory effect. The degradation rate was also function of pH.     

Fenton试剂对富营养化湖水黑臭的氧化降解作用

通过室内实验,研究Fenton试剂对富营养化水体黑臭物质氧化降解作用。实验结果表明,在黑臭的富营养化水中投加Fenton试剂20 min后,水体臭味明显降低,90 min后水体臭味全部消除;水体浊度、色度有显著改善,水体浊度、色度去除率分别达73.73%和93.11%,显著高于对照组的53.4%和22%;水体溶解氧量显著提高;水体的pH值保持在7左右。鱼类毒理实验结果表明,最佳剂量的Fenton试剂对实验鱼类无急性毒性作用。     

Government Sponsored Air Pollution Research Relating to Agriculture

The absorption of hydrogen sulfide and methyl mercaptan by aqueous solutions of chlorine, sodium hydroxide, and chlorine plus sodium hydroxide was studied using a two-inch diameter absorption column packed with ¼ inch Intalox saddles. Absorption rates were noticeably affected by chemical reactions occurring in the aqueous chlorine and hydroxide media. These solutions were studied as a means of controlling sulfur-containing gas emissions from kraft paper mills. The absorption studies indicated that aqueous chlorine solutions at a pH above 12 were effective absorbents for hydrogen sulfide removal in absorption equipment designed to tolerate sulfur in suspension. The absorption of methyl mercaptan in aqueous chlorine solutions appeared to be impractical since dimethyl disulfide was apparently the only product formed and was stripped from the tower by the gas stream. Sodium hydroxide solution was an effective absorbent for both methyl mercaptan and hydrogen sulfide when hydroxide to sulfide or mercaptan feed ratios were greater than 1 or 1.8, respectively. The mercaptan absorption coefficient was approximately twice that for sulfide absorption.     

分散染料生产废水治理工艺的研究

采用微电解一生化一氧化法工艺处理分散染料生产废水，以微电解作为废水的预处理，可去除綮不水中大部分色度，使可生化性提高；生化处理可去除大部分ＣＯＤｃｒ；进一步去除色度和ＣＯＤｃｒ。实验结果表明，整个工艺ＣＯＤｃｒ增除率可达９０％，色度去除率可达９６％，取得满意较的效果。     

Quantitative Determination of Formaldehyde in the Parts Per Hundred Million Concentration Level

A new method has been developed for the determination of trace quantities of formaldehyde and appears to be superior to existing methods. The procedure is based on a modification of Schiff’s test for aldehydes. A mixture of dichlorosulfitomercurate II complex and acid bleached pararosaniline hydrochloride is used as the reagent. In the presence of formaldehyde, a purple color is produced. The method is highly sensitive to formaldehyde and acetaldehyde, simple and does not require concentrated acids. When applied to air pollution studies, the method is virtually free of interferences from higher aldehydes. The paper describes the application of this method to spot sampling of the atmosphere and to continuous atmospheric analysis.     

钛基IrO2-SnO2电极在烟气海水脱硫恢复系统中的应用

采用浸渍-热分解法制备了含IrOx-TiO2中间层的IrO2-SnO2电极,得到的电极具有较高的析氯电催化活性和较强的稳定性,并通过电化学氧化法对Na2SO3海水脱硫模拟液进行处理,考察了电流密度、温度、pH值和电解时间等电解工艺参数对Na2SO3去除率和化学需氧量COD的影响。结果表明,在电流密度为200 mA/cm^2,pH值为3.5,电解440 mg/L的Na2SO3海水脱硫模拟液,15 min时Na2SO3去除率可达96.5%,COD去除率可达82.6%。