Emissions from US waste collection vehicles

This research is an in-depth environmental analysis of potential alternative fuel technologies for waste collection vehicles. Life-cycle emissions, cost, fuel and energy consumption were evaluated for a wide range of fossil and bio-fuel technologies. Emission factors were calculated for a typical waste collection driving cycle as well as constant speed. In brief, natural gas waste collection vehicles (compressed and liquid) fueled with North-American natural gas had 6–10% higher well-to-wheel (WTW) greenhouse gas (GHG) emissions relative to diesel-fueled vehicles; however the pump-to-wheel (PTW) GHG emissions of natural gas waste collection vehicles averaged 6% less than diesel-fueled vehicles. Landfill gas had about 80% lower WTW GHG emissions relative to diesel. Biodiesel waste collection vehicles had between 12% and 75% lower WTW GHG emissions relative to diesel depending on the fuel source and the blend. In 2011, natural gas waste collection vehicles had the lowest fuel cost per collection vehicle kilometer travel. Finally, the actual driving cycle of waste collection vehicles consists of repetitive stops and starts during waste collection; this generates more emissions than constant speed driving.     

Mitigation of global greenhouse gas emissions from waste: conclusions and strategies from the Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report. Working Group III (Mitigation).

Greenhouse gas (GHG) emissions from post-consumer waste and wastewater are a small contributor (about 3%) to total global anthropogenic GHG emissions. Emissions for 2004-2005 totalled 1.4 Gt CO2-eq year(-1) relative to total emissions from all sectors of 49 Gt CO2-eq year(-1) [including carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), and F-gases normalized according to their 100-year global warming potentials (GWP)]. The CH4 from landfills and wastewater collectively accounted for about 90% of waste sector emissions, or about 18% of global anthropogenic methane emissions (which were about 14% of the global total in 2004). Wastewater N2O and CO2 from the incineration of waste containing fossil carbon (plastics; synthetic textiles) are minor sources. Due to the wide range of mature technologies that can mitigate GHG emissions from waste and provide public health, environmental protection, and sustainable development co-benefits, existing waste management practices can provide effective mitigation of GHG emissions from this sector. Current mitigation technologies include landfill gas recovery, improved landfill practices, and engineered wastewater management. In addition, significant GHG generation is avoided through controlled composting, state-of-the-art incineration, and expanded sanitation coverage. Reduced waste generation and the exploitation of energy from waste (landfill gas, incineration, anaerobic digester biogas) produce an indirect reduction of GHG emissions through the conservation of raw materials, improved energy and resource efficiency, and fossil fuel avoidance. Flexible strategies and financial incentives can expand waste management options to achieve GHG mitigation goals; local technology decisions are influenced by a variety of factors such as waste quantity and characteristics, cost and financing issues, infrastructure requirements including available land area, collection and transport considerations, and regulatory constraints. Existing studies on mitigation potentials and costs for the waste sector tend to focus on landfill CH4 as the baseline. The commercial recovery of landfill CH4 as a source of renewable energy has been practised at full scale since 1975 and currently exceeds 105 Mt CO2-eq year(-1). Although landfill CH4 emissions from developed countries have been largely stabilized, emissions from developing countries are increasing as more controlled (anaerobic) landfilling practices are implemented; these emissions could be reduced by accelerating the introduction of engineered gas recovery, increasing rates of waste minimization and recycling, and implementing alternative waste management strategies provided they are affordable, effective, and sustainable. Aided by Kyoto mechanisms such as the Clean Development Mechanism (CDM) and Joint Implementation (JI), the total global economic mitigation potential for reducing waste sector emissions in 2030 is estimated to be > 1000 Mt CO2-eq (or 70% of estimated emissions) at costs below 100 US$ t(-1) CO2-eq year(-1). An estimated 20-30% of projected emissions for 2030 can be reduced at negative cost and 30-50% at costs < 20 US$ t(-) CO2-eq year(-1). As landfills produce CH4 for several decades, incineration and composting are complementary mitigation measures to landfill gas recovery in the short- to medium-term--at the present time, there are > 130 Mt waste year(-1) incinerated at more than 600 plants. Current uncertainties with respect to emissions and mitigation potentials could be reduced by more consistent national definitions, coordinated international data collection, standardized data analysis, field validation of models, and consistent application of life-cycle assessment tools inclusive of fossil fuel offsets.     

Waste plastics recycling process using coke ovens

The Japan Iron and Steel Federation (JISF), as its voluntary energy-saving action plan, proposed a 10% energy reduction by 2010 with 1990 as the basis. Further, it has suggested an additional 1.5% energy saving by the use of waste plastics as a metallurgical raw material. The amount of processing of waste plastics which corresponds to this amount of energy conversion is about 1 million t scale during 1 year. Conventional known methods for recycle-processing of waste plastics include, for example, the method of injection into a blast furnace to use waste plastics as an iron-ore reducing agent instead of coal. On the other hand, the coking process is considered to be suitable as a waste plastic recycling facility because the process involves coal carbonization in a high-temperature and reducing atmosphere. Carbonization tests with mixed waste plastics were conducted with laboratory equipment and in actual coke ovens. As a result, it was confirmed that the waste plastics recycling process using coke ovens is feasible. Therefore, a waste plastics recycling process using coke ovens was started as a chemical recycling technology at Nippon Steel.     

Networking possibilities for waste recycling in Miyagi prefecture, Japan

Successful case studies for waste recycling in Japan have not been evaluated. The evaluation of economic efficiency and environmental effects were lacking at the time the actual network was established. A waste/resource input/output (I/O) coincidence retrieval system called ZENESYS was developed to examine the usefulness of a waste-exchange network in a nonmanufacturing district. We analyzed data from the Miyagi prefecture, a region without heavy industry. The data were collected from 77 companies using a questionnaire and interviews. A total of 33 possible waste exchange links arose after analysis using ZENESYS. However, these were frail networks that relied heavily on the construction industry. Two waste recycling technologies were selected from the ZENESYS database: reclaiming fuel from waste plastic and making construction materials from bottom ash. Evaluation of the environmental effects and economics of these two technologies showed they were both suitable for the environment, but no profit was made from reclaiming fuel from waste plastics. We concluded that in an area with no heavy industry, it may be difficult to adopt recycling technologies that have high environmental and economic performance. Materials are difficult to circulate among manufacturing industries even if a waste-exchange network exists, and resources are consumed during transportation and recycling.     

Spatial simulation and LCA evaluation on the plastic waste recycling system in Tianjin

With the rapid economic development in China, the amount of plastic waste (PW) generated has greatly increased and much of the waste is currently not treated. To reduce greenhouse gas (GHG) emissions from recycling of PW, we estimated the PW flow and considered methods to improve the household PW recycling system in Tianjin by adjusting processes during transportation and establishing a PW recycling factory in Zi’ya Industrial Park. The goal of the study was to identify reasonable improvements for the recycling system and clarify the environmental load. Geographic information system (GIS) technology was used to simulate transport processes for comparing GHG emissions from the transport processes between the present case and an improved case. Life cycle assessment (LCA) was used to compare GHG emissions between a projected scenario and a baseline scenario. Estimated GHG emissions during transport processes in the improved case were reduced by about 12,197 t CO₂ eq per year compared to the present case, equivalent to about 65.9 % of the total emissions in the present case. GHG emissions in the projected scenario were about 101,738 t CO₂ eq less per year than the baseline scenario, equivalent to about 75.5 % of the total emissions in the baseline scenario.     

GHG emission factors developed for the recycling and composting of municipal waste in South African municipalities

GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well as for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from ?290 kg CO₂ e (glass) to ?19 111 kg CO₂ e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO₂ e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard.     

Evaluation of material recycling for plastics: environmental aspects

“Zero emissions” is a concept envisaging the creation of a sustainable society with minimal disposal of resources. In order to realize zero emissions for plastics, it is important to establish a method for quantitatively evaluating candidate recycling processes. In this study, the principle of the substitution factor (SF) is introduced. A quantitative evaluation of the recycling process for plastics was then carried out. The production process for monofilament plastics was examined. The recycling of plastics discarded during the production process could be substituted in small amounts for virgin materials, giving reduced CO₂ emissions. Furthermore, production using recycled material mixed with virgin material was more effective in reducing CO₂ emissions than when recycled materials only were used. Received: November 19, 1999 / Accepted: November 28, 2000     

Comparing the greenhouse gas emissions from three alternative waste combustion concepts

Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO₂-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.     

Energy conservation and CO2 emission reductions due to recycling in Brazil

The present paper aims to make the energy saving potential provided by waste recycling in Brazil evident by pointing out more specifically the benefits regarding climate change mitigation. In this case, based on the energy saved due to the recycling process of an exogenous amount of waste, we have built two scenarios in order to show the potential for indirectly avoiding CO2 emissions in the country as a result of the recycling process. According to the scenario, 1 Mt and 3.5 Mt of CO2, respectively, would be avoided per year due to solid waste recycling. The international context for greenhouse gas emissions reduction, such as the United Nations Framework Convention on Climate Change and its Kyoto Protocol has been taken into account.     

Solid waste recycling within higher education in developing countries: a case study of the University of Lagos

To create a truly circular economy requires a shift from the traditional view of waste disposal to one of resource management. This is particularly important in developing countries, where municipal waste generation is increasing, and efficient recovery of economic value from waste is rarely achieved. Conducted in the University of Lagos (UoL), Nigeria, this study investigated the efficiency of a recycling scheme with the goal of making recommendations to improve the process. UoL’s recycling policy centers around source segregation of waste into color-coded bins. Waste audit was carried out using the output method and interviews were conducted with staff from the waste management team to understand practices on campus. Substantial contamination of colored bins with non-target material was observed. Organics (30%), mixed plastics (28%) and paper (24%) were the most abundant materials, hence have the greatest potential for recovery, and income generation, if segregation rates could be improved. Despite its recycling policy and infrastructure, 99% of UoL waste was going to landfill. Poor policy implementation results in low recovery rates. Targeted waste reduction and increased material recovery would enhance efficiency. Improved awareness of recycling benefits, in addition to policy enforcement, could serve as tools to increase stakeholder participation in recycling.

     

Life cycle assessment of integrated recycling schemes for plastic containers and packaging with consideration of resin composition

Many life cycle assessment studies have evaluated and compared the environmental performance of various technologies for recycling plastic containers and packaging in Japan and other countries. However, no studies have evaluated the combination of recycling technologies in consideration of the resin composition in terms of the quantity of each recycled product so as to maximize their environmental potential. In this study, 27 scenarios of recycling schemes for household waste plastic containers and packaging are developed through integrating a conventional recycling scheme with additional recycling schemes. The conventional recycling scheme involves municipal curbside collection and either the material recycling or feedstock recycling of waste plastics. The additional recycling schemes are feedstock recycling in steel works of the residue from conventional material recycling processes, and corporate voluntary collection and independent material recycling of specific types of plastic trays. Life cycle assessment based on the modeling of recycling processes considering the resin composition in terms of the quantity of each recycled product is applied to evaluate and compare these scenarios from the viewpoints of fossil resource consumption and CO₂ emission. The results show that the environmental loads are reduced in all scenarios including the additional recycling schemes compared with the conventional recycling scheme. However, the independent plastic tray recycling scheme exhibits lower additional environmental savings when the residue recycling scheme is integrated with the conventional material recycling scheme. This is because both additional recycling schemes aim to utilize polystyrene and polyethylene terephthalate, which would otherwise be incinerated as residue from material recycling processes. The evaluation of the environmental loads of plastic recycling with consideration of the resin composition in terms of the quantity of each recycled product makes it possible to investigate recycling schemes that integrate different technologies to maximize their environmental potential.     

Quantification of greenhouse gas emissions from waste management processes for municipalities--a comparative review focusing on Africa

The amount of greenhouse gases (GHG) emitted due to waste management in the cities of developing countries is predicted to rise considerably in the near future; however, these countries have a series of problems in accounting and reporting these gases. Some of these problems are related to the status quo of waste management in the developing world and some to the lack of a coherent framework for accounting and reporting of greenhouse gases from waste at municipal level. This review summarizes and compares GHG emissions from individual waste management processes which make up a municipal waste management system, with an emphasis on developing countries and, in particular, Africa. It should be seen as a first step towards developing a more holistic GHG accounting model for municipalities. The comparison between these emissions from developed and developing countries at process level, reveals that there is agreement on the magnitude of the emissions expected from each process (generation of waste, collection and transport, disposal and recycling). The highest GHG savings are achieved through recycling, and these savings would be even higher in developing countries which rely on coal for energy production (e.g. South Africa, India and China) and where non-motorized collection and transport is used. The highest emissions are due to the methane released by dumpsites and landfills, and these emissions are predicted to increase significantly, unless more of the methane is captured and either flared or used for energy generation. The clean development mechanism (CDM) projects implemented in the developing world have made some progress in this field; however, African countries lag behind.     

Reducing the environmental impact of methane emissions from dairy farms by anaerobic digestion of cattle waste

Four dairy cattle farms considered representative of Northern Spain milk production were studied. Cattle waste was characterised and energy consumption in the farms was inventoried. Methane emissions due to slurry/manure management and fuel consumption on the farms were calculated. The possibility of applying anaerobic digestion to the slurry to minimise emissions and of using the biogas produced to replace fossil fuels on the farm was considered. Methane emissions due to slurry management (storage and use as fertiliser) ranged from 34 to 66 kg CH₄ cow⁻¹ year⁻¹ for dairy cows and from 13 to 25 kg CH₄ cow⁻¹ year⁻¹ for suckler calves. Cattle on these farms are housed for most of the year, and the contribution from emissions from manure dropped in pastures is insignificant due to the very low methane conversion factors. If anaerobic digestion were implemented on the farms, the potential GHG emissions savings per livestock unit would range from 978 to 1776 kg CO₂ eq year⁻¹, with the main savings due to avoided methane emissions during slurry management. The methane produced would be sufficient to supply digester heating needs (35-55% of the total methane produced) and on-farm fuel energy requirements.     

Waste-to-energy: A review of the status and benefits in USA

The USA has significant experience in the field of municipal solid waste management. The hierarchy of methodologies for dealing with municipal solid wastes consists of recycling and composting, combustion with energy recovery (commonly called waste-to-energy) and landfilling. This paper focuses on waste-to-energy and especially its current status and benefits, with regard to GHG, dioxin and mercury emissions, energy production and land saving, on the basis of experience of operating facilities in USA.     

Options for sustainable industrial waste management toward zero landfill waste in a high-density polyethylene (HDPE) factory in Thailand

The feasibility of the 3R concept tends to increase the reduction, reuse, and recycling of industrial waste. In this study, we investigated the feasibility of 3R methods to cope with industrial waste generated from high-density polyethylene production in Thailand. The sources and types of waste and existing waste management practices were identified. The four sources of waste generation that we identified were: (1) production, (2) packaging, (3) wastewater treatment, and (4) maintenance, distributed as 47, 46, 4, and 3 %, respectively. The main options for management were: sales to recycling plants (60.41 %), reuse and recycling (25.93 %), and industrial-waste landfilling (10.47 %). After 3R options were introduced, the proposed alternatives were found to be capable of reducing the amount of waste by 33.88 %. The results of life-cycle assessment (LCA) were useful for considering the environmental impact where 3R options were adopted. We also found that net greenhouse gas (GHG) emissions and other environmental impacts could be reduced when industrial waste diverted from landfill is used as alternative fuel. However, the cost of waste disposal seems to be the greatest obstacle for the adoption of 3R methods in Thailand.     

Japan’s greenhouse gas reduction scenarios toward net zero by 2050 in the material cycles and waste management sector

The first draft scenario toward net zero greenhouse gas (GHG) emissions by 2050 for the material cycles and waste management sector was presented by the Ministry of the Environment, Japan in August 2021. The details of the future GHG emission estimation used to create the draft scenario are described in this document. For multiple scenarios where more aggressive measures, such as carbon capture, utilization, and storage (CCUS), were included in addition to business-as-usual and the current policy continuity scenario, future GHG emissions were estimated as the sum of the products of activities and emission factors indicating changes in measures between scenarios. The estimation outcomes demonstrated that future GHG emissions from the solid waste management sector could be anticipated to be zero or even negative when material conversion to biomass, primarily for plastics, recycling to raw materials, and installation of CCUS at incineration facilities are assumed. Extensions of prior plans are not enough to reach the goal of net zero emissions, according to the measures necessary and the volume and pace of their implementation suggested in this study. Stakeholders should collaborate with great ambition.

     

A simple model for complex waste recycling scenarios in developing economies

Future uncertainties involved in the current waste management activities in the developing nations have been addressed through determining plastic waste recovery, recycling and landfilling scenarios in two case study countries — Bangladesh and India. In order to discern and comprehend the material in-flow and out-flow of such complex successive plastics recoveries and recyclings, within the closed-loop recycling systems present in these two countries, a simple mathematical model is developed. The model is based on limited published information, on extensive fieldwork in Dhaka, Calcutta and Delhi, and on experimental data. An environmental legislative factor has been included in the model which will allow balancing of the quality of recycled products and the amount of landfilling non-recyclable plastics. The model has the potential to create and predict a sound waste database for these countries. Bangladesh has been chosen as a model developing country for this study. The mathematical model can be used in future decision making processes within the plastics recycling arena of the countries concerned to achieve an environmentally sound and cost effective waste management option.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Building recycling rates through the informal sector

Many developing country cities aspire to modern waste management systems, which are associated with relatively high recycling rates of clean, source separated materials. Most already have informal sector recycling systems, which are driven solely by the revenues derived from selling recovered materials, even though they are saving the formal sector money by reducing waste quantities. There is clear potential for 'win-win' co-operation between the formal and informal sectors, as providing support to the informal sector, to build recycling rates and to address some of the social issues could reduce the overall costs of waste management for the formal sector. This paper shows that recycling rates already achieved by the informal sector can be quite high, typically in the range from 20% to 50%; often up to half of this is in the form of clean, source separated materials collected directly from households and businesses by itinerant waste buyers. Four country case studies provide a number of lessons on how this solid foundation could be used to build high recycling rates of clean materials.     

水处理技术发展对电力工业水循环利用的经济性影响

讨论了一些为提高生产力和降低成本而发展起来的废水零排放或水回收循环利用前沿技术,并将这些技术的经济性与原有的水循环利用系统进行比较.