臭氧氧化结合氨水吸收的烟气脱硫脱氮研究

用氨水溶液吸收法脱除烟气中被臭氧氧化后的SOx、NOx,分析了吸收反应的产物,得出了化学反应的总方程式,利用热力学原理计算了化学反应达到平衡时SOx、NOx、CO2的分压;对氨水吸收法脱除烟气中被臭氧氧化后的SOx、NOx的吸收机理进行了研究,分析了SOx、NOx在氨水溶液中的吸收特性.结果表明:臭氧氧化结合氨水吸收同...     

燃煤烟气脱硫脱硝脱碳一体化技术的研究进展

我国长期以来一直以煤炭为主要能源,其燃烧排放的SOx和NOx是大气环境中主要的污染物,而CO2的大量排放也会导致一系列环境问题的出现.本文总结了燃煤烟气的净化方法,重点介绍了吸附法、吸附机理、传统吸附剂以及新型吸附剂、影响吸附效果的因素和吸附剂循环再生情况.最后总结了吸附剂目前存在的一些缺陷以及未来的发展方向.     

燃煤烟气中汞形态分析的实验研究

在一维煤粉燃烧炉台架上采用EPA推荐的Ontario Hydro方法 ,测量了燃烧不同煤种排放的烟气中汞的形态分布情况 .结果表明 ,烟气中汞以颗粒态和气态汞的形式存在 .气态汞总量在 9— 2 3 μg·Nm- 3范围内 ,主要以单质汞的形式存在 ,占气态汞总量的 5 2 %—83 % ,而二价汞占 1 7%— 48% .飞灰中汞的浓度大大超过了底灰中汞的浓度 ,表明汞在飞灰中富集 ,在底灰中分散的行为     

臭氧发生器研究进展

由于臭氧在水处理中具有广阔的应用前景,故臭氧发生器的研制一直是人们关注的重大研究课题,并介绍了国内外臭氧发生器在电极结构、介质材料等方面的研究进展.     

窑炉烟气净化和控制燃烧相结合技术

窑炉烟气污染治理技术的关键是要解决降低高温烟气以实现机械排烟的条件，而在采用配风形式降低了高温烟气和通过选用适宜的湿式净化技术装置解决了污染问题的同时，必须考虑控制窑炉燃烧，以保证窑炉的正常运行，并改善窑炉燃烧条件，使窑炉的产品质量得到保证和提高，实现环保与节能降耗的双重效果。     

氧气顶吹转炉烟气净化与回收

一、工程简介上钢三厂,转炉炼钢分厂的三座25t纯氧顶吹转炉,年产良锭100～110万t,主要产品为普通碳素结构钢BY2、BY3,优质碳素结构钢08,低合金钢20MnSi,所有产品为镇静钢锭、坯.二、生产工艺流程转炉炼钢的铁水由化铁炉供给,冶炼成合格钢水后,经连铸机浇注成矩形钢坯和模铸成254mm钢锭,分厂连铸比为70%,其生产工艺流程见下图.     

臭氧和基于臭氧的高级氧化工艺降解农药的研究进展

由于农药的环境持久性以及毒性,饮用水源中的农药微污染日益受到水处理行业的关注.在众多水处理工艺中,由于其高效氧化去除有机污染物及控制嗅味等特点,臭氧及其相关高级氧化技术的应用已日趋广泛.本文综述了这些氧化技术对多类代表性农药（包括有机氯、有机磷、氨基甲酸酯、氯乙酰胺和三嗪等）的降解效能,详细讨论了农药的降解效率、反应动...     

燃煤烟气中气态Hg0污染物吸附剂的研究进展

对目前燃煤烟气中气态Hg0污染物吸附剂进行了分类研究,重点总结了碳基吸附剂、层状矿物类吸附剂、磁性吸附剂等3类吸附剂的特点,对气态Hg0的吸附效果及吸附机理进行了深入探讨.通过分析比较,提出了研制高效吸附剂的主要途径,并展望了气态Hg0吸附剂的发展趋势.     

臭氧对植物新陈代谢的影响

从气孔反应、膜透性变化、光合作用反应、物质代谢变化和酶活性变化等５个方面系统综述了臭氧对植物新陈代谢的影响。     

臭氧对活性污泥性状的影响

分别在臭氧浓度为31.50,31.96,32.23,33.89,36.65,39.33和40.25mg·l-1下,考察污泥混合液MLSS,MLVSS和pH值及上清液SCOD,TN,NH3-N和,TP等随臭氧作用时间的变化.结果表明:臭氧对污泥混合液中的溶解性同体(DS)具有氧化作用,能有效破解微生物絮体、细胞壁和细胞膜等,使微生物体内有机质溶出,溶出物能被微生物作为底物重新利用,本实验中,MLSS和MLVSS降低最大量分别为1250 mg·l-1和465 Mg·l-1,SCOD增加最大量为250.3 mg·l-1.另外,根据混合液各性状的变化规律分析了臭氧氧化污泥的机理.     

高分辨率气相色谱/高分辨率质谱同位素内标法测定烟气样品中的多氯萘

多氯萘(PCNs)同二噁英(PCDD/Fs)和类二噁英多氯联苯(PCBs)类似,在烟气中的含量处于痕量水平,一般都在pg·m-3以下,因此分析方法要求有较高的灵敏度和选择性.以国内外的研究方法和参考文献为基础,建立了同位素内标稀释高分辨气相色谱/高分辨率质谱联用对垃圾焚烧发电厂的烟气样品中的PCNs进行分析.结果表明,该方法对17种氯取代位的PCNs单体的空白干扰在N.D.—2.1 pg之间;方法检出限范围为2.8—9.1 pg·nm-3,线性范围为0.40—240 pg·μL-1;空白加标实验中目标化合物的回收率为84.62%—116.21%,提取内标回收率为40.41%—75.79%,采样内标的回收率为88.92%—89.89%.实际烟气样品测得17种PCNs的同系物浓度分布在8.79—509 pg·nm-3之间,PCN-6的含量最高,PCNs-31S含量最低,相对标准偏差在4.43%—14.44%.该分析方法具有较高的准确性和可靠性,适用于烟气样品中多氯萘物质的测定.     

Treatment of biologically treated effluents from baker's yeast industry by membrane and ozone technologies

This paper presents pilot‐scale membrane treatment results performed on biologically treated effluents from fermentation industry and ozone oxidation on concentrates from the same membrane treatment system. The results obtained from the ultrafiltration (UF) and/or the reverse osmosis (RO) systems indicate that membrane treatment are very effective for COD, Color, NH₃‐N and conductivity removal. Ozone oxidation of the membrane concentrates was tested to increase biodegradability of the wastes. The initial ratios of Biochemical oxygen demand (BOD₅) to Chemical oxygen demand (COD) were increased significantly by applying chemicaloxidation with O₃ and O₃ + H₂O₂.     

臭氧降解乐果机理探讨

研究了臭氧对乐果的降解效果及其影响因素。试验结果表明,当初始臭氧浓度为10mg·L-1时,5min内可使乐果降解80%左右,延长反应时间,乐果降解率无明显增加。同时,通过在乐果和臭氧的反应液中再分别添加重碳酸盐与叔丁醇,探讨臭氧降解乐果的反应机理,结果表明臭氧降解乐果是分子反应。GC-MS检测经臭氧处理的水样发现有氧化乐果存在,表明若臭氧处理不完全,水样中可产生毒副产物。     

南京北郊大气臭氧浓度变化特征

以南京北郊大气中O3质量浓度观测资料为基础,分析了O3变化特征和气象要素对其影响程度。结果表明：大气O3日均质量浓度平均为65.8μg·m-3。O3质量浓度最大值出现在午后15时左右,O3质量浓度日最大值在春季最大,而冬季最小。白天工作日O3质量浓度要高于周末,而夜间两者差异不大。气温,日照时数和降水量是影响南京大气O3质量浓度的重要因素。全年中5月份高日照时数和较低的降水量导致南京出现O3高值。在偏南气流作用下,O3质量浓度偏高。由气象要素得到的O3日均质量浓度和O3日最高质量浓度回归方程相关系数分别为0.61和0.71。     

Mercury removal from flue gas using nitrate as an electron acceptor in a membrane biofilm reactor

Membrane bioreactor achieved mercury removal using nitrate as an electron acceptor. The biological mercury oxidation increased with the increase of oxygen concentration. Ferrous sulfide could make both Hg²⁺ and MeHg transform into HgS-like substances. Nitrate drives mercury oxidation through katE, katG, nar, nir, nor, and nos. Mercury (Hg⁰) is a hazardous air pollutant for its toxicity, and bioaccumulation. This study reported that membrane biofilm reactor achieved mercury removal from flue gas using nitrate as the electron acceptor. Hg⁰ removal efficiency was up to 88.7% in 280 days of operation. Oxygen content in flue gas affected mercury redox reactions, mercury biooxidation and microbial methylation. The biological mercury oxidation increased with the increase of oxygen concentration (2%‒17%), methylation of mercury reduced with the increase of oxygen concentration. The dominant bacteria at oxygen concentration of 2%, 6%, 17%, 21% were Halomonas, Anaerobacillus, Halomonas and Pseudomonas, respectively. The addition of ferrous sulfide could immobilize Hg²⁺ effectively, and make both Hg²⁺ and MeHg transform into HgS-like substances, which could achieve the inhibition effect of methylation, and promote conversion of mercury. The dominant bacteria changed from Halomonas to Planctopirus after FeS addition. Nitrate drives mercury oxidation through katE, katG, nar, nir, nor, and nos for Hg⁰ removal in flue gas.     

Advanced purification and comprehensive utilization of yellow phosphorous off gas

Yellow phosphorous is an important raw material in the chemical industry. However, during the production of yellow phosphorous, high concentrations of carbon monoxide and other impurities are released. Without appropriate purification and removal, this off gas has potential to cause severe pollution problems once released. Purified yellow phosphorous off gas can be beneficially reused as a raw material in chemical production for synthesis of high value-added chemical reagents. In this paper, the significance of purification and reutilization of yellow phosphorous off gas are explored. The principles, processes, and main characteristics of the technologies for purification and reuse of yellow phosphorus off gas (including technical measurements of impurity reduction, relevant engineering cases, and public acceptance of the technologies) are summarized. In view of the existing problems and scientific development requirements, this paper proposes several recommendations for green production based on the concept of recycle economics. We conclude that advanced purification and comprehensive reutilization can be an effective solution for heavy pollution resulting from yellow phosphorous off gassing.     

天气条件对福州近地层臭氧分布的影响

利用2009—2010年福州市近地层臭氧连续观测资料,并结合气象资料分析不同天气型对臭氧浓度变化的影响,以及臭氧浓度与气象要素的相关性。结果表明：在高压后部、地面倒槽等6种天气型影响下,福州市臭氧浓度值较高;在低涡锋面、台风（热带辐合带）等4种天气型影响下,臭氧浓度值较低。导致福州市臭氧平均浓度值最高的天气型是台风（热带辐合带）外围,最低的是低涡锋面系统。高压后部、地面倒槽和锋前暖区等强暖性、且非常不利于污染物扩散的天气型易造成臭氧浓度超标。臭氧浓度与气象要素关系密切,与温度、日照、太阳辐射显著正相关,与云量、相对湿度、降水量显著负相关,受偏南和偏东风影响,平均风速较大时,臭氧浓度较高,在SSE方位上臭氧小时浓度超标率最高。     

Leaching of elements from flue dust produced in copper scrap smelting process

To understand the features and leaching characteristics of copper (Cu) scrap smelting dust and its potential risk to environment and humans, three types of smelting dust were sampled and investigated. The dust samples were collected from the dust captured by cyclone collector, panel cooler, and bag house in a typical Cu scrap smelting process of a factory in Guangxi of China. Zinc (Zn), Cu and lead (Pb) were the main elements of the samples of cyclone collector dust (CCD), panel cooler dust (PCD), and bag house dust (BHD). There were less arsenic (As), Pb and Cu in CCD than PCD and BHD, and PCD contained more manganese (Mn), nickel (Ni), and iron (Fe) than BHD. The particle shapes of BHD appeared more regular than CCD and PCD, and energy dispersive X-ray spectroscopy analysis illustrated the compositions of selected surface areas of three samples. The size of particles ranged from 0.011 to 33.11 μm in CCD, from less than 1 μm to several mm in PCD, and from 0.832 to 363.078 μm in BHD. The main elements in leachate were Zn and Mn from CCD, Zn, cadmium (Cd) and Pb from PCD, Zn, Mn and Cd from BHD. The leaching toxicity risk of Cd, Mn, and Zn of PCD and BHD was higher than CCD.     

天气条件对福州近地层臭氧分布的影响

利用2009—2010年福州市近地层臭氧连续观测资料,并结合气象资料分析不同天气型对臭氧浓度变化的影响,以及臭氧浓度与气象要素的相关性。结果表明:在高压后部、地面倒槽等6种天气型影响下,福州市臭氧浓度值较高;在低涡锋面、台风(热带辐合带)等4种天气型影响下,臭氧浓度值较低。导致福州市臭氧平均浓度值最高的天气型是台风(热带辐合带)外围,最低的是低涡锋面系统。高压后部、地面倒槽和锋前暖区等强暖性、且非常不利于污染物扩散的天气型易造成臭氧浓度超标。臭氧浓度与气象要素关系密切,与温度、日照、太阳辐射显著正相关,与云量、相对湿度、降水量显著负相关,受偏南和偏东风影响,平均风速较大时,臭氧浓度较高,在SSE方位上臭氧小时浓度超标率最高。