Formation of disinfection byproducts in typical Chinese drinking water

Eight typical drinking water supplies in China were selected in this study. Both source and tap water were used to investigate the occurrence of chlorinated disinfection byproducts (DBPs), and seasonal variation in the concentrations of trihalomethanes (THMs) of seven water sources was compared. The results showed that the pollution level for source water in China, as shown by DBP formation potential, was low. The most encountered DBPs were chloroform, dichloroacetic acid, trichloroacetic acid, and chlorodibromoacetic acid. The concentration of every THMs and haloacetic acid (HAA) compound was under the limit of standards for drinking water quality. The highest total THMs concentrations were detected in spring.     

Nontargeted identification of peptides and disinfection byproducts in water

A broad range of organic compounds are known to exist in drinking water sources and serve as precursors of disinfection byproducts(DBPs).Epidemiological findings of an association of increased risk of bladder cancer with the consumption of chlorinated water has resulted in health concerns about DBPs.Peptides are thought to be an important category of DBP precursors in water.However,little is known about the actual presence of peptides and their DBPs in drinking water because of their high sample complexity and low concentrations.To address this challenge and identify peptides and non-chlorinated/chlorinated peptide DBPs from large sets of organic compounds in water,we developed a novel high throughput analysis strategy,which integrated multiple solid phase extraction(SPE),high performance liquid chromatography(HPLC)separation,and non-target identification using precursor ion exclusion(PIE)high resolution mass spectrometry(MS).After MS analysis,structures of candidate compounds,particularly peptides,were obtained by searching against the Human Metabolome Database(HMDB).Using this strategy,we successfully detected 625 peptides(out of 17,205 putative compounds)and 617 peptides(out of 13,297)respectively in source and finished water samples.The source and finished water samples had 501 peptides and amino acids in common.The remaining 116 peptides and amino acids were unique to the finished water.From a subset of 30 putative compounds for which standards were available,25 were confirmed using HPLC-MS analysis.By analyzing the peptides identified in source and finished water,we successfully confirmed three disinfection reaction pathways that convert peptides into toxic DBPs.     

A balancing act: Optimizing free chlorine contact time to minimize iodo-DBPs, NDMA, and regulated DBPs in chloraminated drinking water

Many drinking water treatment plants in the U.S. have switched from chlorination to chloramination to lower levels of regulated trihalomethane (THM) and haloacetic acid (HAA) disinfection byproducts (DBPs) in drinking water and meet the current regulations. However, chloramination can also produce other highly toxic/carcinogenic, unregulated DBPs: iodo-acids, iodo-THMs, and N-nitrosodimethylamine (NDMA). In practice, chloramines are generated by the addition of chlorine with ammonia, and plants use varying amounts of free chlorine contact time prior to ammonia addition to effectively kill pathogens and meet DBP regulations. However, iodo-DBPs and nitrosamines are generally not considered in this balancing of free chlorine contact time. The goal of our work was to determine whether an optimal free chlorine contact time could be established in which iodo-DBPs and NDMA could be minimized, while keeping regulated THMs and HAAs below their regulatory limits. The effect of free chlorine contact time was evaluated for the formation of six iodo-trihalomethanes (iodo-THMs), six iodo-acids, and NDMA during the chloramination of drinking water. Ten different free chlorine contact times were examined for two source waters with different dissolved organic carbon (DOC) and bromide/iodide. For the low DOC water at pH 7 and 8, an optimized free chlorine contact time of up to 1 h could control regulated THMs and HAAs, as well as iodo-DBPs and NDMA. For the high DOC water, a free chlorine contact time of 5 min could control iodo-DBPs and NDMA at both pHs, but the regulated DBPs could exceed the regulations at pH 7.     

生物过滤饮用水深度处理:机遇与挑战

源水水质的恶化给传统的饮用水处理工艺带来了挑战.生物过滤是饮用水消毒输配之前管理、维护及增强颗粒滤料表面生物活性以去除有机和无机物的过程.由于具有高效、低成本等优点，生物过滤在饮用水深度处理工艺中逐渐得到广泛的应用.本文综述了生物过滤在饮用水处理过程中对水中溶解性有机质（消毒副产物前体物）的去除、微量污染物的削减、嗅味化合物及氨氮的去除等.此外，针对生物过滤在水深度处理过程中存在的问题，本文详细讨论了含氮消毒副产物前体物的生成、低温下生物过滤效能下降等挑战，并提出了今后需要研究的问题.     

Formation and control of disinfection byproducts and toxicity during reclaimed water chlorination: A review

Chlorination is essential to the safety of reclaimed water; however, this process leads to concern regarding the formation of disinfection byproducts (DBPs) and toxicity. This study reviewed the formation and control strategies for DBPs and toxicity in reclaimed water during chlorination. Both regulated and emerging DBPs have been frequently detected in reclaimed water during chlorination at a higher level than those in drinking water, indicating they pose a greater risk to humans. Luminescent bacteria and Daphnia magna acute toxicity, anti-estrogenic activity and cytotoxicity generally increased after chlorination because of the formation of DBPs. Genotoxicity by umu-test and estrogenic activity were decreased after chlorination because of destruction of toxic chemicals. During chlorination, water quality significantly impacted changes in toxicity. Ammonium tended to attenuate toxicity changes by reacting with chlorine to form chloramine, while bromide tended to aggravate toxicity changes by forming hypobromous acid. During pretreatment by ozonation and coagulation, disinfection byproduct formation potential (DBPFP) and toxicity formation potential (TFP) occasionally increase, which is accompanied by DOC removal; thus, the decrease of DOC was limited to indicate the decrease of DBPFP and TFP. It is more important to eliminate the key fraction of precursors such as hydrophobic acid and hydrophilic neutrals. During chlorination, toxicities can increase with the increasing chlorine dose and contact time. To control the excessive toxicity formation, a relatively low chlorine dose and short contact time were required. Quenching chlorine residual with reductive reagents also effectively abated the formation of toxic compounds.     

Disinfection byproduct regulatory compliance surrogates and bromide-associated risk

Natural and anthropogenic factors can alter bromide concentrations in drinking water sources. Increasing source water bromide concentrations increases the formation and alters the speciation of disinfection byproducts (DBPs) formed during drinking water treatment. Brominated DBPs are more toxic than their chlorinated analogs, and thus have a greater impact on human health. However, DBPs are regulated based on the mass sum of DBPs within a given class (e.g., trihalomethanes and haloacetic acids), not based on species-specific risk or extent of bromine incorporation. The regulated surrogate measures are intended to protect against not only the species they directly represent, but also against unregulated DBPs that are not routinely measured. Surrogates that do not incorporate effects of increasing bromide may not adequately capture human health risk associated with drinking water when source water bromide is elevated. The present study analyzes trihalomethanes (THMs), measured as TTHM, with varying source water bromide concentrations, and assesses its correlation with brominated THM, TTHM risk and species-specific THM concentrations and associated risk. Alternative potential surrogates are evaluated to assess their ability to capture THM risk under different source water bromide concentration conditions. The results of the present study indicate that TTHM does not adequately capture risk of the regulated species when source water bromide concentrations are elevated, and thus would also likely be an inadequate surrogate for many unregulated brominated species. Alternative surrogate measures, including THM3 and the bromodichloromethane concentration, are more robust surrogates for species-specific THM risk at varying source water bromide concentrations.     

The role of metal oxides on oxidant decay and disinfection byproduct formation in drinking waters: Relevance to distribution systems

Maintaining a residual disinfectant/oxidant (e.g., chlorine and chlorine dioxide), is a generally used strategy to control microbial contaminants and bacterial regrowth in distribution systems. Secondarily oxidant, such as hypobromous acid (HOBr), can be formed during chlorination of bromide-containing waters. The decay of oxidants and formation of disinfection byproducts (DBPs) due to the interaction between oxidants and selected metal oxides were studied. Selected metal oxides generally enhanced the decay of these halogen-containing oxidants via three pathways: (1) catalytic disproportionation to yield an oxidized form of halogen (i.e., halate) and reduced form (halide for chlorine and bromine or chlorite for chlorine dioxide), (2) oxygen formation, and (3) oxidation of a metal in a reduced form (e.g., cuprous oxide) to a higher oxidation state. Cupric oxide (CuO) and nickel oxide (NiO) showed significantly strong abilities for the first pathway, and oxygen formation was a side reaction. Cuprous oxide can react with oxidants via the third pathway, while goethite was not involved in these reactions. The ability of CuO on catalytic disproportionation of HOBr remained stable up to four cycles. In chlorination process, bromate formation tends to be important (exceeding 10 µg/L) when initial bromide concentration is above 400 µg/L in the presence of dissolved organic matter. Increasing initial bromide concentrations increased the formation of DBPs and calculated cytotoxicity, and the maximum was observed at pH 8.6 during chlorination process. Therefore, the possible disinfectant loss and DBP formation should be carefully considered in drinking water distribution systems.     

Formation potential and analysis of 32 regulated and unregulated disinfection by-products: Two new simplified methods

Water disinfection is an essential process that provides safe water by inactivating pathogens that cause waterborne diseases. However, disinfectants react with organic matter naturally present in water, leading to the formation of disinfection by-products (DBPs). Multi-analyte methods based on mass spectrometry (MS) are preferred to quantify multiple DBP classes at once however, most require extensive sample pre-treatment and significant resources. In this study, two analytical methods were developed for the quantification of 32 regulated and unregulated DBPs. A purge and trap (P&T) coupled with gas chromatography mass spectrometry (GC-MS) method was optimized that automated sample pre-treatment and analyzed volatile and semi-volatile compounds, including trihalomethanes (THMs), iodinated trihalomethanes (I-THMs), haloacetonitriles (HANs), haloketones (HKTs) and halonitromethanes (HNMs). LOQs were between 0.02-0.4 µg/L for most DBPs except for 8 analytes that were in the low µg/L range. A second method with liquid chromatography (LC) tandem mass spectrometry (MS/MS) was developed for the quantification of 10 haloacetic acids (HAAs) with a simple clean-up and direct injection. The LC-MS/MS direct injection method has the lowest detection limits reported (0.2-0.5 µg/L). Both methods have a simple sample pre-treatment, which make it possible for routine analysis. Hyperchlorination and uniform formation conditions (UFC) formation potential tests with chlorine were evaluated with water samples containing high and low TOC. Hyperchlorination formation potential test maximized THMs and HAAs while UFC maximized HANs. Ascorbic acid was found to be an appropriate quencher for both analytical methods. Disinfected drinking water from four water utilities in Alberta, Canada were also evaluated.     

Chloramination of wastewater effluent: Toxicity and formation of disinfection byproducts

The reclamation and disinfection of waters impacted by human activities (e.g., wastewater effluent discharges) are of growing interest for various applications but has been associated with the formation of toxic nitrogenous disinfection byproducts (N-DBPs). Monochloramine used as an alternative disinfectant to chlorine can be an additional source of nitrogen in the formation of N-DBPs. Individual toxicity assays have been performed on many DBPs, but few studies have been conducted with complex mixtures such as wastewater effluents. In this work, we compared the cytotoxicity and genotoxicity of wastewater effluent organic matter (EfOM) before and after chloramination. The toxicity of chloraminated EfOM was significantly higher than the toxicity of raw EfOM, and the more hydrophobic fraction (HPO) isolated on XAD-8 resin was more toxic than the fraction isolated on XAD-4 resin. More DBPs were also isolated on the XAD-8 resin. N-DBPs (i.e., haloacetonitriles or haloacetamides) were responsible for the majority of the cytotoxicity estimated from DBP concentrations measured in the XAD-8 and XAD-4 fractions (99.4% and 78.5%, respectively). Measured DBPs accounted for minor proportions of total brominated and chlorinated products, which means that many unknown halogenated compounds were formed and can be responsible for a significant part of the toxicity. Other non-halogenated byproducts (e.g., nitrosamines) may contribute to the toxicity of chloraminated effluents as well.     

How well does XAD resin extraction recover halogenated disinfection byproducts for comprehensive identification and toxicity testing?

Halogenated disinfection byproducts (DBPs) are an unintended consequence of drinking water disinfection, and can have significant toxicity. XAD resins are commonly used to extract and enrich trace levels of DBPs for comprehensive, nontarget identification of DBPs and also for in vitro toxicity studies. However, XAD resin recoveries for complete classes of halogenated DBPs have not been evaluated, particularly for low, environmentally relevant levels (ng/L to low µg/L). Thus, it is not known whether levels of DBPs or the toxicity of drinking water might be underestimated. In this study, DAX-8/XAD-2 layered resins were evaluated, considering both adsorption and elution from the resins, for extracting 66 DBPs from water. Results demonstrate that among the 7 classes of DBPs investigated, trihalomethanes (THMs), including iodo-THMs, were the most efficiently adsorbed, with recovery of most THMs ranging from 50%-96%, followed by halonitromethanes (40%-90%). The adsorption ability of XAD resins for haloacetonitriles, haloacetamides, and haloacetaldehydes was highly dependent on the individual species. The adsorption capacity of XAD resins for haloacetic acids was lower (5%-48%), even after adjusting to pH 1 before extraction. Recovery efficiency for most DBPs was comparable with their adsorption, as most were eluted effectively from XAD resins by ethyl acetate. DBP polarity and molecular weight were the two most important factors that determine their recovery. Recovery of trichloromethane, iodoacetic acid, chloro- and iodo-acetonitrile, and chloroacetamide were among the lowest, which could lead to underestimation of toxicity, particularly for iodoacetic acid and iodo-acetonitrile, which are highly toxic.     

Do DBPs swim in salt water pools? Comparison of 60 DBPs formed by electrochemically generated chlorine vs. conventional chlorine

Disinfectants are added to swimming pools to kill harmful pathogens. Although liquid chlorine(sodium hypochlorite) is the most commonly used disinfectant, alternative disinfection techniques like electrochemically generated mixed oxidants or electrochemically generated chlorine, often referred to as salt water pools, are growing in popularity. However, these disinfectants react with natural organic matter and anthropogenic contaminants introduced to the pool water by swimmers to form disinfectio...     

蓝藻AOM特征与DBPs生成关系的研究进展

蓝藻水华期间,藻细胞因自然生长或受水处理工艺影响(如预氧化和混凝),会向水中释放大量藻源有机物(AOM),能够与氯消毒剂反应生成大量消毒副产物(DBPs),增加了饮用水安全风险.了解AOM的特征及其对DBPs生成的影响对于AOM的控制和饮用水安全保障至关重要.本文综述了蓝藻AOM的主要理化特征(溶解性有机碳、溶解性有机...     

Synergistic cytotoxicity of binary combinations of inorganic and organic disinfection byproducts assessed by real-time cell analysis

Chlorine, chlorine dioxide, and ozone are widely used as disinfectants in drinking water treatments. However, the combined use of different disinfectants can result in the formation of various organic and inorganic disinfection byproducts (DBPs). The toxic interactions, including synergism, addition, and antagonism, among the complex DBPs are still unclear. In this study, we established and verified a real-time cell analysis (RTCA) method for cytotoxicity measurement on Chinese hamster ovary (CHO) cell. Using this convenient and accurate method, we assessed the cytotoxicity of a series of binary combinations consisting of one of the 3 inorganic DBPs (chlorite, chlorate, and bromate) and one of the 32 regulated and emerging organic DBPs. The combination index (CI) of each combination was calculated and evaluated by isobolographic analysis to reflect the toxic interactions. The results confirmed the synergistic effect on cytotoxicity in the binary combinations consisting of chlorite and one of the 5 organic DBPs (2 iodinated DBPs (I-DBPs) and 3 brominated DBPs (Br-DBPs)), chlorate and one of the 4 organic DBPs (3 aromatic DBPs and dibromoacetonitrile), and bromate and one of the 3 organic DBPs (2 I-DBPs and dibromoacetic acid). The possible synergism mechanism of organic DBPs on the inorganic ones may be attributed to the influence of organic DBPs on cell membrane and cell antioxidant system. This study revealed the toxic interactions among organic and inorganic DBPs, and emphasized the latent adverse outcomes in the combined use of different disinfectants.     

Formation potentials of typical disinfection byproducts and changes of genotoxicity for chlorinated tertiary effluent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 ...     

Occurrence of selected aliphatic amines in source water of major cities in China

The formation of toxic nitrogenous disinfection byproducts (N-DBPs), such as nitrosamines, halonitromethanes and haloacetonitriles, from reactions between chlorine/chloramine and dissolved organic nitrogen in drinking water has caused great concern with regarding public health. This study revealed the occurrence of 17 aliphatic amines, some of which have been confirmed to be the precursors of N-DBPs, in source water across China. A sensitive method based on benzenesulfonyl chloride derivatization and liquid-liquid extraction followed by GC-MS analysis was established for the simultaneous analysis of the selected amines in aqueous samples. In total, 37 source water samples from the capital cities of 20 provinces were collected for the survey. Among the 17 amines, 14 were detected with an average frequency of detection of 36%. The most relevant amines in terms of frequency and maximum concentrations detected were dimethylamine (100%, 24.82 μg/L), methylamine (78%, 0.92 μg/L), N-methylethylamine (70%, 8.84 μg/L), propylamine (59%, 10.69 μg/L), diethylamine (54%, 3.76 μg/L), N-methylbutylamine (35%, 3.07 μg/L), N-ethylpropylamine (35%, 0.52 μg/L), and piperidine (32%, 2.35 μg/L). This is the first large scale survey of the aliphatic amines occurrence in source water in the world. The wide presence of nitrosamine precursors like dimethylamine, N-methylethylamine and diethylamine, and the precursors of haloacetonitriles and halonitromethanes like methylamine and propylamine suggests that better source water management is required to ensure the safety of drinking water.     

Disinfection byproducts in chlorinated or brominated swimming pools and spas: Role of brominated DBPs and association with mutagenicity

Although the health benefits of swimming are well-documented, health effects such as asthma and bladder cancer are linked to disinfection by-products (DBPs) in pool water. DBPs are formed from the reaction of disinfectants such as chlorine (Cl) or bromine (Br) with organics in the water. Our previous study (Daiber et al., Environ. Sci. Technol. 50, 6652; 2016) found correlations between the concentrations of classes of DBPs and the mutagenic potencies of waters from chlorinated or brominated swimming pools and spas. We extended this study by identifying significantly different concentrations of 21 individual DBPs in brominated or chlorinated pool and spa waters as well as identifying which DBPs and additional DBP classes were most associated with the mutagenicity of these waters. Using data from our previous study, we found that among 21 DBPs analyzed in 21 pool and spa waters, the concentration of bromoacetic acid was significantly higher in Br-waters versus Cl-waters, whereas the concentration of trichloroacetic acid was significantly higher in Cl-waters. Five Br-DBPs (tribromomethane, dibromochloroacetic acid, dibromoacetonitrile, bromoacetic acid, and tribromoacetic acid) had significantly higher concentrations in Br-spa versus Cl-spa waters. Cl-pools had significantly higher concentrations of Cl-DBPs (trichloroacetaldehyde, trichloromethane, dichloroacetic acid, and chloroacetic acid), whereas Br-pools had significantly higher concentrations of Br-DBPs (tribromomethane, dibromoacetic acid, dibromoacetonitrile, and tribromoacetic acid). The concentrations of the sum of all 4 trihalomethanes, all 11 Br-DBPs, and all 5 nitrogen-containing DBPs were each significantly higher in brominated than in chlorinated pools and spas. The 8 Br-DBPs were the only DBPs whose individual concentrations were significantly correlated with the mutagenic potencies of the pool and spa waters. These results, along with those from our earlier study, highlight the importance of Br-DBPs in the mutagenicity of these recreational waters.     

Disinfection by-product (DBP) research in China: Are we on the track?

Disinfection by-products (DBPs) formed during water disinfection has drawn significant public concern due to its toxicity. Since the first discovery of the trihalomethanes in 1974, continued effort has been devoted on DBPs worldwide to investigate the formation mechanism, levels, toxicity and control measures in drinking water. This review summarizes the main achievements on DBP research in China, which included: (1) the investigation of known DBP occurrence in drinking water of China; (2) the enhanced removal of DBP precursor by water treatment process; (3) the disinfection optimization to minimize DBP formation; and (4) the identification of unknown DBPs in drinking water. Although the research of DBPs in China cover the whole formation process of DBPs, there is still a challenge in effectively controlling the drinking water quality risk induced by DBPs, an integrated research framework including chemistry, toxicology, engineering, and epidemiology is especially crucial.     

Disinfection byproduct formation from algal organic matters after ozonation or ozone combined with activated carbon treatment with subsequent chlorination

Algal organic matter (AOM), including extracellular organic matter (EOM) and intracellular organic matter (IOM) from algal blooms, is widely accepted as essential precursors of disinfection byproducts (DBPs). This study evaluated the effect of ozonation or ozone combined with activated carbon (O₃-AC) treatment on characteristic alternation and DBP formation with subsequent chlorination of Chlorella sp.. The effects of pH and bromide concentration on DBP formation by ozonation or O₃-AC treatment were also investigated. Results showed that the potential formation of DBPs might be attributed to ozonation, but these DBP precursors could be further removed by activated carbon (AC) treatment. Moreover, the formation of target DBPs was controlled at acidic pH by alleviating the reactions between chlorine and AOM. Besides, the bromide substitution factor (BSF) value of trihalomethanes (THMs) from EOM and IOM remained constant after AC treatment. However, THM precursors could be significantly decreased by AC treatment. The above results indicated that O₃-AC was a feasible treatment method for algal-impacted water.     

黄河原水中消毒副产物前体物的组成特征及其化学预氧化处理效果对比

以取自河南省郑州市石佛原水厂的黄河原水为研究对象,系统研究了原水中消毒副产物(DBPs)前体物的组成规律,对比分析了3种预氧化剂(高锰酸钾、自由氯和二氧化氯)对原水中DBPs生成潜能的消减规律.试验结果表明:原水中DBPs的前体物均以小分子有机物和疏水性组分(52.51%)为主;分子量小于1 k Da有机物组分是生成含氮消毒副产物(N-DBPs)和三卤甲烷(THMs)的主要前体物;疏水性有机物是生成THMs的主要前体物,亲水性有机物是生成N-DBPs的主要前体物.经Cl2预氧化后,直接生成的DBPs随着自由氯投加量的增加而增加,Cl O2和KMn O4预氧化直接增加DBPs产生量.经3种预氧化剂氧化后,原水中三卤甲烷生成潜能(THMFP)均呈现一定的下降,其降低量依次为Cl O2Cl2KMn O4;然而3种预氧化剂都不能有效的减少含氮消毒副产物生成潜能(N-DBPFP),Cl O2预氧化和Cl2预氧化可增加N-DBPs生成潜能,尤其在较高投加量下,Cl2预氧化将大大增加N-DBPs生成潜能.为有效消减总DBPs生成潜能,水厂可优先采用KMn O4或Cl O2作为预氧化剂处理引黄水库或沉砂池水.     

Formation and speciation of disinfection byproducts during chlor(am)ination of aquarium seawater

The chemistry associated with the disinfection of aquarium seawater is more complicated than that of freshwater, therefore limited information is available on the formation and speciation of disinfection byproducts(DBPs) in marine aquaria. In this study, the effects of organic precursors, bromide(Br-) and pre-ozonation on the formation and speciation of several typical classes of DBPs, including trihalomethanes(THM4), haloacetic acids(HAAs),iodinated trihalomethanes(I-THMs), and haloacetamides(HAc Ams), were investigated during the chlorination/chloramination of aquarium seawater. Results indicate that with an increase in dissolved organic carbon concentration from 4.5 to 9.4 mg/L, the concentrations of THM4 and HAAs increased by 3.2–7.8 times under chlorination and by 1.1–2.3 times under chloramination. An increase in Br-concentration from 3 to 68 mg/L generally enhanced the formation of THM4, I-THMs and HAc Ams and increased the bromine substitution factors of all studied DBPs as well, whereas it impacted insignificantly on the yield of HAAs. Pre-ozonation with 1 mg/L O3 dose substantially reduced the formation of all studied DBPs in the subsequent chlorination and I-THMs in the subsequent chloramination. Because chloramination produces much lower amounts of DBPs than chlorination, it tends to be more suitable for disinfection of aquarium seawater.