校园再生水回用工程设计

采用A2/O及深度处理工艺处理校园生活污水,再生水回用于校园人工湖补水和杂用。工程造价少,运行费低,运行出水同时达到景观用水和杂用水水质标准。     

煤化工废水中硫酸盐还原菌的分离及鉴定

从煤化工废水和厌氧污泥中分离出2株高效的硫酸盐还原菌,通过革兰氏染色、扫描电子显微镜观察其形态,通过16S r DNA序列分析法鉴定其种属,并研究其生长特性和硫酸盐还原性能。实验结果表明:菌株SRB-1为革兰氏阴性柠檬酸杆菌;菌株SRB-2为革兰氏阳性丁酸梭菌;两种菌株在最佳条件下培养4 d,菌液菌量均可达到1×106个/m L的水平;在SO2-4质量浓度为1 360 mg/L的条件下,两种菌株的SO2-4去除率分别达到93%和95%。     

高盐有机化工废水中COD与TOC的相关性

以COD为指标评价废水的有机物污染程度存在诸多不足,而TOC能更好地反映废水中有机物的含量。以高盐有机化工废水为研究对象,利用多级活性炭吸附工艺对其进行预处理,对原水、吸附出水、再生液中COD与TOC的相关性进行了分析。分析结果表明：在一定范围内,原水COD与TOC满足关系式COD = 56.537 7+ 0.967 04TOC;废水在吸附处理过程中,COD与TOC仍呈线性相关关系,但不同工段需各自建立独立的回归方程;TOC测定结果的精密度较好,且远优于COD直接测定的精密度,回收率范围98.59%~110.69%;利用线性回归方程根据TOC测定结果预测COD,预测结果准确、可靠、精密度好。     

综合印染废水混凝试验研究

考察了几种常用混凝剂对印染废水的处理效果。研究表明,在最佳pH值9～11时,硫酸亚铁具有较好的处理效果;复配试验表明,当硫酸亚铁投加量为400mg／l,熟石灰400mg／1,PAM为2mg／l时,COD去除率76．3％,色度去除率94．5％．处理成本为0．16元／t。     

高氨氮化工废水MBBR—AMBBR—MBBR组合工艺处理

采用移动床生物膜反应器（MBBR）—厌氧移动床生物膜反应器（AMBBR）—MBBR组合工艺处理高氨氮化工废水。反应器采用几何构型优化、比表面积大的新型YD-25生物载体和DNF-203硝化细菌,实现了同步硝化和反硝化,强化了脱氮能力。采用投加菌种和排泥的方式,经27 d的驯化培养即完成了反应器的挂膜启动。试验结果表明：最佳操作条件为HRT 8 d、MBBR中DO 3 mg/L、进水pH 8.0;在进水COD 2 840~7 437 mg/L、ρ（氨氮）92~179 mg/L、TN 148~258 mg/L、pH 6~8的条件下,出水指标均值为COD 352 mg/L、ρ（氨氮）21.2 mg/L、TN 36 mg/L、pH 7.4,满足排放要求。     

臭氧氧化处理化工污水厂尾水

采用臭氧氧化工艺处理某化工污水厂尾水,考察了臭氧投加量对废水处理效果的影响,并进行了反应动力学研究。实验结果表明,最佳臭氧投加量为67 mg/L,在此条件下,处理后废水的COD去除率为19%,色度去除率为90%,UV254去除率为79%,BOD5/COD为0.11。反应动力学分析结果表明:臭氧氧化去除废水COD的反应适合采用二级反应动力学进行拟合,二级反应动力学方程为y=0.000 1x+0.000 3,相关系数为0.938 5;臭氧氧化去除废水色度的反应更适合采用一级反应动力学进行拟合,一级反应动力学方程为y=0.105 0x-0.018 4,相关系数为0.990 3。     

煤化工企业高盐废水的“零排放”技术

采用“混凝沉淀-微滤-组合反渗透”工艺对某煤化工企业的高盐废水进行浓缩处理,浓水通过蒸发结晶进行脱水,产水采用常规反渗透进行水回收。运行结果表明,经30 d运行,水回收率保持在85%以上,脱盐率稳定在95%以上,常规反渗透产水水质稳定,产水电导率、浊度、Cl^-质量浓度和COD的平均值分别为12.5 μs/cm,0.1 NTU,7.8 mg/L,1.8 mg/L,满足《炼化企业节水减排考核指标与回用水质控制指标》（Q/SH0104-2007）中污水回用于循环冷却水的水质指标和设计产水水质要求,实现了废水的近“零排放”。     

Review of biosolids management options and co-incineration of a biosolid-derived fuel

This paper reviews current biosolids management options, and identifies incineration as a promising technology. Incineration is attractive both for volume reduction and energy recovery. Reported emissions from the incineration of biosolids were compared to various regulations to identify the challenges and future direction of biosolids incineration research. Most of the gaseous and metal emissions were lower than existing regulations, or could be met by existing technologies. This paper also presents the results of an experimental study to investigate the potential use of biosolids for co-incineration with wood pellets in a conventional wood pellet stove. Pilot scale combustion tests revealed that co-incineration of 10% biosolids with 90% premium grade wood pellets resulted in successful combustion without any significant degradation of efficiency and emissions.     

超超临界机组酸洗废水零排放处理工艺研究及应用

锅炉酸洗废水具有排放量大、污染物浓度高和处理难度极大的特点。为实现酸洗废水处理后复用,不外排,分析了河源电厂2×600 MW超超临界机组酸洗废水成份,进行了小型模拟处理试验,探索了降低废水中金属离子含量、COD和浊度的方法。根据试验结果,采用稀释、pH调整、曝气、絮凝、沉淀及机械过滤的方法对锅炉酸洗废水进行处理,处理后的清水作为脱硫系统的工艺补充水。脱硫系统排出的废水采用蒸发结晶工艺进行处理,处理后的冷凝水作为冷却塔补充水回收利用,最终实现零排放,可为火电厂酸洗废水的处理利用提供参考。     

我国现代煤化工项目废水处理的误区和建议

介绍了我国现代煤化工项目的废水来源及特性,归纳了废水的处理技术路线,从废水"零排放"、废水处理技术与管理、蒸发塘的污染转移、废水处理与固体废物处理及废气处理的关系、污染物源头控制等方面阐述了我国当前煤化工废水处理存在的误区和建议。     

次氯酸钠废液活化法制备柚子皮活性炭

以柚子皮为原料,采用次氯酸钠废液活化法制备了柚子皮活性炭,通过正交实验优化了制备条件,并运用SEM、FTIR和XRD技术对活性炭产品进行了表征。实验结果表明:制备柚子皮活性炭的最佳工艺条件为炭化温度350℃、次氯酸钠废液含量25%(φ)、次氯酸钠废液活化时间25 min、高温活化温度650℃、高温活化时间60 min;最佳条件下,柚子皮活性炭的产率为31.88%、碘吸附值为854 mg/g、亚甲基蓝吸附值为216.9 mg/g。表征结果显示:活化后的柚子皮炭具有更大的孔体积、更有序的孔径排布和更发达的孔隙结构;柚子皮活性炭表面存在大量的含氧基团;柚子皮活性炭的石墨化度为61.32%,具有较高的稳定性。     

循环式复合水解酸化—CASS—絮凝沉淀组合工艺处理化工园区废水

采用循环式复合水解酸化—CASS—絮凝沉淀组合工艺处理江苏省某化工园区污水厂的实际废水(COD260~815 mg/L、ρ(氨氮)19.15~40.41 mg/L、TN 22.51~50.66 mg/L、TP 0.79~3.21 mg/L),考察了污染物浓度的沿程变化,评价了各工段对主要污染物的去除效果。实验结果表明,组合工艺对废水有着较好的处理效果,平均COD、氨氮、TN、TP的去除率分别高达83.29%、95.34%、61.29%、82.70%,平均出水COD、ρ(氨氮)、TN、TP分别为56.2,1.27,14.34,0.33 mg/L,出水水质接近GB 18918—2002《城镇污水处理厂污染物排放标准》的一级A标准。     

不饱和季铵盐的合成及其聚合物在化工及环保领域的应用

按不饱和基团的类型对不饱和季铵盐进行了分类,并综述了其合成方法。介绍了其聚合物在含油污水处理、抗菌、纺织品、新材料等领域的应用。阐述了在不饱和季铵盐的开发及其聚合物的应用方面存在的问题。指出了今后的发展方向:应该加大科研投入,加快新型不饱和季铵盐的研发进程,特别是在主结构设计、纯度提高以及新型絮凝剂单体的多样性方面,以制备出多功能性的单体和聚合物。     

Environmental burdens in the management of end-of-life cathode ray tubes

We compared the environmental burdens in the management of end-of life cathode ray tubes (CRTs) within two frameworks according to the different technologies of the production of televisions/monitors. In the first case, CRT recycling is addressed to the recovery of the panel and funnel glass for the manufacturing of new CRT screens. In the second case, where flat screen technology has replaced that of CRT, the recycling is addressed to the recovery of the glass cullet and lead for other applications. The impacts were evaluated according to the problem-oriented methodology of the Institute of Environmental Sciences, Leiden University, Leiden, The Netherlands. Our data confirm that in both cases, the recycling treatment allows benefits to be gained for the environment through the recovery of the secondary raw materials. These benefits are higher for the “CRT technology” framework (1 kg CO₂ saved per CRT) than for the “flat screen technology” (0.9 kg CO₂ saved, per CRT, as the highest possible), mainly due to the high energy consumption for lead separation from the funnel glass. Furthermore, the recovery of yttrium from the fluorescent powders that are a residue of the recycling treatment would further improve the CO₂ credit for both the frameworks considered, which would provide a further saving of about 0.75 kg CO₂ per CRT, net of the energy and raw materials needed for the recovery.Overall, this study confirms that, even with a change in the destination of the recovered materials, the recycling processes provide a benefit for the environment: indeed the higher loads for the environment are balanced by avoiding the primary production of the recovered materials.     

Geotechnical properties of municipal solid waste at different phases of biodegradation

This paper presents the results of laboratory investigation conducted to determine the variation of geotechnical properties of synthetic municipal solid waste (MSW) at different phases of degradation. Synthetic MSW samples were prepared based on the composition of MSW generated in the United States and were degraded in bioreactors with leachate recirculation. Degradation of the synthetic MSW was quantified based on the gas composition and organic content, and the samples exhumed from the bioreactor cells at different phases of degradation were tested for the geotechnical properties. Hydraulic conductivity, compressibility and shear strength of initial and degraded synthetic MSW were all determined at constant initial moisture content of 50% on wet weight basis. Hydraulic conductivity of synthetic MSW was reduced by two orders of magnitude due to degradation. Compression ratio was reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. Direct shear tests showed that the fresh and degraded synthetic MSW exhibited continuous strength gain with increase in horizontal deformation, with the cohesion increased from 1 kPa for fresh MSW to 16–40 kPa for degraded MSW and the friction angle decreased from 35° for fresh MSW to 28° for degraded MSW. During the triaxial tests under CU condition, the total strength parameters, cohesion and friction angle, were found to vary from 21 to 57 kPa and 1° to 9°, respectively, while the effective strength parameters, cohesion and friction angle varied from 18 to 56 kPa and from 1° to 11°, respectively. Similar to direct shear test results, as the waste degrades an increase in cohesion and slight decrease in friction angle was observed. Decreased friction angle and increased cohesion with increased degradation is believed to be due to the highly cohesive nature of the synthetic MSW. Variation of synthetic MSW properties from this study also suggests that significant changes in geotechnical properties of MSW can occur due to enhanced degradation induced by leachate recirculation.     

曲靖电厂灰渣性质及其用作水泥混合材的试验研究

在对粉煤灰及炉渣的主要物理、化学性质进行分析测试的基础上，对它们用作水泥混合材所表现出的性能及存在的问题进行了分析研究。     

Effects of olive mill wastewater and olive mill pomace on soil physicochemical properties and soil polyphenols

Journal of Material Cycles and Waste Management - Every year, worldwide olive oil extraction processes produce huge amounts of by-products such as (olive mill wastewater and olive mill pomace) in a...     

An evaluation of legislative measures on electrical and electronic waste in the People's Republic of China

With the increasing number of recycling mishaps in connection with waste electronic and electrical equipment (WEEE) in the People's Republic of China, it is imperative that the handling and recycling of WEEE be sufficiently regulated in China. Regulations covering three major issues, namely, take-back issues, controls on hazardous substances in WEEE and the assurance of good environmental management in WEEE plants, were promulgated between 2006 and 2008. The evaluation in this country report shows that few of these regulatory measures have performed satisfactorily in terms of enforcement, of public acceptance and of environmental concerns. In brief, the take-back requirements and the associated financial responsibilities are only vaguely defined; the control on hazardous substances and the so-called "environmental expiry date" requirements cannot be properly enforced, and the resources needed to ensure the satisfactory enforcement of the environmental abatement and pollution control requirements in WEEE plants are overwhelming. In addition, the use of a "multiple enforcement body" approach to the control of hazardous substances in WEEE is an indication that the Chinese government lacks the determination to properly enforce the relevant legal requirements.     

化工项目环境风险评价中危险物质临界量的界定

在依据HJ 169—2018《建设项目环境风险评价技术导则》进行危险物质临界量界定的实际应用中,发现该导则存在危险物质种类及危险性质涵盖不全的问题。对比研究了与之相关的HJ 169—2004《建设项目环境风险评价技术导则》、HJ 941—2018《企业突发环境事件风险分级方法》、GB 18218—2018《危险化学品重大危险源辨识》、《赛维索指令Ⅲ》等技术规范和标准,构建了基于上述规范的危险物质临界量界定技术路线,为化工项目环境风险评价的实际工作提供借鉴。     

Catalytic effect of natural clays on properties and chemical structure of recycled polyethylene

Journal of Material Cycles and Waste Management - Montmorillonite clays such as bentonites are often studied and used as reinforcement to thermoplastics, since it can generate nanostructures,...