On-line production of ferrate with an electrochemical method and its potential application for wastewater treatment – A review

A number of studies on the oxidation of various organic/inorganic contaminants by ferrate(VI) were reported in the 1980s and 1990s. The exploration of the use of ferrate(VI) for water and wastewater treatment has been well addressed recently. However, challenges have existed for the implementation of ferrate(VI) technology in practice due to the instability of a ferrate solution or high production cost of solid ferrate products. The research has been carried out aiming at the generation and application of ferrate(VI) in situ. This paper thus reviews ferrate chemistry and its overall performance as a water treatment chemical, discusses the factors affecting the ferrate yield efficiency using the electrochemical method, and finally, summarises the work on the production and use of ferrate in situ which is currently under study.     

高铁酸盐在水和废水处理中的应用进展

本文综述了高铁酸盐用于饮用水的消毒、杀菌、除藻，有机废水的氧化混凝，恶臭物质的氧化去除，重金属离子及放射性废水的混凝沉淀，以及色度浊度的去除等领域的最新进展。并对今后的研究进行了展望。     

Oxidation of inorganic contaminants by ferrates (VI, V, and IV)--kinetics and mechanisms: a review

Inorganic contaminants are found in water, wastewaters, and industrial effluents and their oxidation using iron based oxidants is of great interest because such oxidants possess multi-functional properties and are environmentally benign. This review makes a critical assessment of the kinetics and mechanisms of oxidation reactions by ferrates (Fe(VI)O(4)(2-), Fe(V)O(4)(3-), and Fe(IV)). The rate constants (k, M(-1) s(-1)) for a series of inorganic compounds by ferrates are correlated with thermodynamic oxidation potentials. Correlations agree with the mechanisms of oxidation involving both one-electron and two-electron transfer processes to yield intermediates and products of the reactions. Case studies are presented which demonstrate that inorganic contaminants can be degraded in seconds to minutes by ferrate(VI) with the formation of non-toxic products.     

剩余污泥经臭氧破解后其中碳、氮和磷的变化

在臭氧对污泥进行减量的过程中,针对臭氧作用后污泥中碳、氮和磷数量的变化,对污水处理厂的剩余污泥进行了不同累计时间的臭氧作用研究,结果表明经臭氧破解后污泥中的TN没有较大改变,污泥中的TP最终呈减少趋势,破解液中的COD虽有所增加,但破解液回流到生物系统中反而可以补充反硝化过程中有机碳的不足,从而促进污水生物处理的脱氮除磷作用,臭氧的引入不仅可以减少污水处理厂的运行成本,同时可为城镇污水处理厂全面升级改造提供一定的参考。     

SBR中好氧颗粒污泥的培养

采用竖式SBR作为反应器,利用城市污水处理厂剩余污泥作为接种污泥,通过不间断运行培养出好氧颗粒污泥。实验结果表明,采用非限量曝气模式好氧颗粒污泥降解模拟污水的效果较好,其COD去除率可达98％以上。曝气量对好氧颗粒污泥的形成和稳定具有重要影响,当气速为26．5m／h时,好氧颗粒污泥的性状和处理有机废水效果最佳。同时好氧颗粒污泥对pH值的变化不明显,当pH为5—8范围内,其COD去除率都可达到85％以上。但是未经驯化的好氧颗粒污泥对对硝基苯酚和对氯苯酚两种芳香类有机物较敏感,而对硝基苯酚对其毒性更大。当对硝基苯酚和。对氯苯酚浓度为10mg／L时,其COD去除率仅为42．5％和52％。     

Super—CM利水净处理生活污水的试验研究

Ｓｕｐｅｒ－ＣＭ利水净是利用ＭＡＢ技术研究成功的一种用于治理水污染的新产品。本文介绍了Ｓｕｐｅｒ－ＣＭ利水净结合活性污泥法处理生活污水的一则现场试验案例。试验结果表明,在活性污泥法中加入Ｓｕｐｅｒ－ＣＭ利水净能够有效的提高污水处理能力,在试验后期进水增加３０％的情况下,ＣＯＤ、ＳＳ的平均去除率仍然分别提高了８．７％、４．１％。     

提高曝气池污水处理能力的可行性实践

炼化企业污水场控制污泥膨胀,可以在一定限度内有效提高装置的污水处理能力。通过对大连石化公司污水场进行生产分析,在保持有机负荷F/M相对稳定的条件下,好氧生化单元的污泥浓度由设计值2000～2500mg/L,提高至3500～4000mg/L之间,进水COD去除量由设计值8880kg/d,提高到16000kg/d,使装置的处理能力提高了1.8倍。     

分光光度法测定测田废水中的COD_(Cr)

为了快速监测油田废水中的化学需氧量ＣＯＤＣｒ,因此采用ＴＬ－１（Ａ）型污水ＣＯＤＣｒ速测仪进行加热催化消解,然后再用分光光度比色法测定ＣＯＤＣｒ,实验中进行了方法的准确度、精确度及Ｃｌ－影响实验,并与标准的重铬酸钾法进行了对比实验,结果说明分光光度法简单快速、重现性较好、准确度较高,对同一产品的测定结果与重铬酸钾法非常一致。因此,本方法可用于油田废水中的ＣＯＤＣｒ监测。     

稠油污水生化性处理技术研究

为了探讨稠油污水能否使用生物法处理,以生活污水和农药厂生化池原菌种经过诱导驯化,分别培养了可以在稠油污水中生长的好氧菌种革兰氏阴性菌G-1和厌氧菌种革兰氏阴性菌G-2.以G-2和G-1对稠油污水进行顺序处理,可使其BOD5/CODCr达到0.26;采用SBR法对新疆稠油污水放大处理试验的结果：COD降至150 mg/L以下,各项指标达到GB8978-1998二级排放标准.     

ABR+活性污泥法在番茄废水中的应用

以奇台太极华力食品有限公司番茄废水处理工程实例为依据,介绍了采用ABR厌氧+完全混合活性污泥法工艺在处理番茄加工废水的设计、调试及运行情况。经过2年运行,其进水COD在700~1 500mg/L之间,最大处理水量达到4 000m3/d;出水COD在40~70mg/L之间,COD去除率达到97%。处理出水可以稳定达到污水综合排放二级标准。ABR+完全混合活性污泥法工艺具有启动快,调试时间短,工程造价低的优点,尤其适宜处理番茄等间歇时间长工作时间短的季节性生产污水。     

Treatment and reuse of sewage sludge

Sewage sludge was treated using composting, fixed-bed and stirred anaerobic digesters. The treatment performance in terms of the physico chemical parameters, bacterial indicators and pathogenic forms were assessed. In addition, the biogas production rate was recorded in the case of anaerobic digesters. Composting of the sewage sludge increased its total solids from 39 to 93% after 6 weeks, while the reduction in organic matter was 40% and the total nitrogen and phosphorus contents increased by 22 and 30%, respectively. Complete removal of salmonellae and faecal coliforms occurred, so that the composted sludge could be used as a soil conditioner and fertilizer. The results of the anaerobic treatment indicated that an organic load of 4.8kg COD m–3 per day achieved the best operating conditions for either the stirred or fixed-bed digester. The mean percentage removals of COD, BOD, faecal coliforms, faecal streptococci and the biogas production rate for the stirred digester were 53, 53, 24 and 29% and 259 L kg–1 COD per day, respectively. The corresponding mean percentage removals and production rate for the experiments with a fixed-bed digester were 61, 62, 33 and 35% and 328 L kg–1 COD per day, respectively. Improvements in the BOD and faecal coliform reductions and the gas production rate of 17, 38 and 21%, respectively, were achieved due to the presence of media (Berl saddles) in the fixed-bed digester. The microbial content of the anaerobically treated sludge is too high to be used as a fertilizer, while that of the composted sludge is low enough for such use.     

Transport of di(2-ethylhexyl)phthalate (DEHP) applied with sewage sludge to undisturbed and repacked soil columns

Municipal sewage sludge is often used on arable soils as a source of nitrogen and phosphorus, but it also contains organic contaminants that may be leached to the ground water. Di(2-ethylhexyl)phthalate (DEHP) is a priority pollutant that is present in sewage sludge in ubiquitous amounts. Column experiments were performed on undisturbed soil cores (20-cm depth x 20-cm diameter) with three different soil types: a sand, a loamy sand, and a sandy loam soil. Dewatered sewage sludge was spiked with 14C-labeled DEHP (60 mg kg(-1)) and bromide (5 g kg(-1)). Sludge was applied to the soil columns either as five aggregates, or homogeneously mixed with the surface layer. Also, two leaching experiments were performed with repacked soil columns (loamy sand and sandy loam soil). The DEHP concentrations in the effluent did not exceed 1.0 microg L(-1), and after 200 mm of outflow less than 0.5% of the applied amount was recovered in the leachate in all soils but the sandy loam soil with homogeneous sludge application (up to 3.4% of the applied amount recovered). In the absence of macropore flow, DEHP in the leachate was primarily sorbed to mobilized dissolved organic macromolecules (DOM, 30.3 to 81.3%), while 2.4 to 23.6% was sorbed to mobilized mineral particles. When macropore flow occurred, this changed to 16.5 to 37.4% (DOM) and 36.9 to 40.6% (mineral particles), respectively. The critical combination for leaching of considerable amounts of DEHP was homogeneous sludge application and a continuous macropore structure.     

炼油化工污水处理中活性污泥膨胀原因分析

针对工业废水采用普通活性污泥法处理易出现的丝状菌型污泥膨胀,分析和总结出五种主要膨胀类型:低负荷型、低溶解氧型、营养缺乏型、高硫化物型、pH值不平衡型。对污泥负荷、溶解氧、污水种类、营养成分及pH值和温度的变化等因素对污泥膨胀中菌胶团和丝状菌生长的相互影响进行阐述,给出污泥膨胀理论,并对不同类型的污泥膨胀提出相应的控制方法。     

城市垃圾和污水脱水污泥、排水管污泥混合堆肥工艺研究

城市垃圾和污水脱水污染、排水管污泥已成为现代城市污染的主要总是。由于这些废弃物中有机物质的含量较高,因此可以利用堆肥的方法来进行处理,使其转化为农田的有机肥料,本文用城市生活垃圾和污水处理厂污泥、排水管污泥混合进行堆肥的研究。     

Relationships between anaerobic consortia and removal efficiencies in an UASB reactor degrading 2,4 dichlorophenol (DCP)

To gain more insight into the interactions between anaerobic bacteria and reactor performances (chemical oxygen demand-COD, 2,4 dichlorophenol-2,4 DCP removals, volatile fatty acid-VFA, and methane gas productions) and how they depended on operational conditions the microbial variations in the anaerobic granular sludge from an upflow anaerobic sludge blanket (UASB) reactor treating 2,4 DCP was studied. The study was composed of two parts. In the first part, the numbers of methanogens and acedogens in the anaerobic granular sludge were counted at different COD removal efficiencies. The relationships between the numbers of methanogens, the methane gas production and VFA production were investigated. The COD removal efficiencies increased to 74% from 30% while the number of total acedogens decreased to 10 from 30 cfu ml(-1). The number of total methanogens and acedogens varied between 11 x 10(3) and 10 x 10(9)MPN g(-1) and 10 and 30 cfu ml(-1) as the 2,4 DCP removal efficiencies were obtained between 60% and 99%, respectively. It was seen that, as the number of total acedogens decreased, the COD removal efficiencies increased. However, the number of total methanogens increased as the COD removal efficiencies increased. Correlations between the bacterial number and with the removal efficiencies obtained in different operational conditions were investigated. From the results presented in this paper a high correlation between the number of bacteria, COD removals, methane gas percentage, 2,4 DCP removals and VFA was observed. In the second part, methanogen bacteria in the anaerobic granular sludge were identified. Microbial observations and biochemical tests were applied to identify the anaerobic microorganisms from the anaerobic granular sludge. In the reactor treating 2,4 DCP, Methanobacterium bryantii, Methanobacterium formicicum, Methanobrevibacter smithii, Methanococcus voltae, Methanosarcina mazei, Methanosarcina acetivorans, Methanogenium bourgense and Methanospirillum hungatei were identified.     

Characterization of sewage sludge organic matter using solid-state carbon-13 nuclear magnetic resonance spectroscopy

Six sewage sludges from five sewage treatment plants in Australia were characterized using solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Spectra were acquired both before and after removal of mineral components through treatment with hydrofluoric acid (HF). Carbon mass balance indicated that little organic matter was lost on HF treatment, which significantly improved NMR sensitivity and spectral resolution, and decreased acquisition time and hence cost of NMR analysis. Two NMR techniques were used, the standard cross polarization (CP) technique and Bloch decay (BD). The BD technique had not been applied previously to the analysis of sewage sludge. For each sludge sample, both before and after HF treatment, the BD spectrum contained significantly more alkyl carbon. Spin counting, another technique applied to sewage sludge here for the first time, showed that the BD spectra of the HF-treated sludges were quantitative, while approximately 30% of the CP NMR signal went undetected. The discrepancy between CP and BD spectra was attributed to the presence of alkyl carbon with such high molecular mobility that the efficiency of cross polarization is affected. This study shows that sewage sludge organic matter is significantly different in chemistry to soil organic matter and has implications for the application of sewage sludge to agricultural land.     

法国某生活污水厂污泥好氧消化工艺运行研究

为了提高出水质量,法国小镇Cagnes—sur—Mer的生活污水处理厂从2008年初开始实施高有机负荷的运行,但同时这也提高了出泥产量。由于污泥的处理费用及搬运污泥的交通费用很高,水厂对污泥进行了污泥好氧稳定工艺,工艺使用纯氧机（VSA装置）就地利用空气制氧。工艺投入运行后,每日对好氧消化池的入泥和出泥进行采样和检测（MLSS、MLVSS、pH、COD、DRYNESS etc）以建立完整的运行数据。污泥经好氧消化作用后其有机物含量减少60％以上,每月减少40吨的出泥。同时,消化池的使用还使水厂周日也能对曝气池中的污泥进行抽取,缓解了以往由于周日停止排泥而导致周一曝气池中污泥浓度过大的问题。从而达到优化出水水质的目的。消化池中的温度维持在40℃左右,因为反应为放热反应,所以无需加热设备。此项目所收集到的数据将为这种工艺的发展提供帮助。同时也可以为那些想要减少出泥量的水厂提供一种新的方法。因为它投资小,见效快,操作简单。     

Performance of sequential anaerobic/aerobic digestion applied to municipal sewage sludge

A promising alternative to conventional single phase processing, the use of sequential anaerobic-aerobic digestion, was extensively investigated on municipal sewage sludge from a full scale wastewater treatment plant. The objective of the work was to evaluate sequential digestion performance by testing the characteristics of the digested sludge in terms of volatile solids (VS), Chemical Oxygen Demand (COD) and nitrogen reduction, biogas production, dewaterability and the content of proteins and polysaccharides. VS removal efficiencies of 32% in the anaerobic phase and 17% in the aerobic one were obtained, and similar COD removal efficiencies (29% anaerobic and 21% aerobic) were also observed. The aerobic stage was also efficient in nitrogen removal providing a decrease of the nitrogen content in the supernatant attributable to nitrification and simultaneous denitrification. Moreover, in the aerobic phase an additional marked removal of proteins and polysaccharides produced in the anaerobic phase was achieved. The sludge dewaterability was evaluated by determining the Optimal Polymer Dose (OPD) and the Capillary Suction Time (CST) and a significant positive effect due to the aerobic stage was observed. Biogas production was close to the upper limit of the range of values reported in the literature in spite of the low anaerobic sludge retention time of 15 days. From a preliminary analysis it was found that the energy demand of the aerobic phase was significantly lower than the recovered energy in the anaerobic phase and the associated additional cost was negligible in comparison to the saving derived from the reduced amount of sludge to be disposed.     

Economic evaluation of sewage treatment processes in India

This paper evaluates the total annual cost including capital and operation and maintenance (O&M) costs for the up-flow anaerobic sludge blanket (UASB) and waste stabilization pond (WSP) systems operated in India. It also compares UASB and WSP systems with the activated sludge process (ASP) and biological aerated filter (BAF) systems in terms of total annual cost and chemical oxygen demand (COD) removal cost by assuming various annual interest rates and land prices. It was found that the relationship between capital and O&M costs per unit size of a UASB or WSP system and its treatment capacity can be established by a first-order equation. The relation between the cost of organic removal and capital or O&M cost for various sewage treatment systems at various annual interest rates revealed that, for the Indian context, UASB could be the most suitable option in terms of expenses and treatment efficiency.     

Para-chlorophenol containing synthetic wastewater treatment in an activated sludge unit: effects of hydraulic residence time

Due to the toxic nature of chlorophenol compounds present in some chemical industry effluents, biological treatment of such wastewaters is usually realized with low treatment efficiencies. Para-chlorophenol (4-chlorophenol, 4-CP) containing synthetic wastewater was treated in an activated sludge unit at different hydraulic residence times (HRT) varying between 5 and 30 h while the feed COD (2500 mg l(-1)), 4-CP (500 mg l(-1)) and sludge age (SRT, 10 days) were constant. Effects of HRT variations on COD, 4-CP, toxicity removals and on settling characteristics of the sludge were investigated. Percent COD removals increased and the effluent COD concentrations decreased when HRT increased from 5 to 15 h and remained almost constant for larger HRT levels. Nearly, 91% COD and 99% 4-CP removals were obtained at HRT levels above 15 h. Because of the highly concentrated microbial population at HRT levels of above 15 h, low effluent (reactor) 4-CP concentrations and almost complete toxicity removals were obtained. High biomass concentrations obtained at HRT levels above 15 h were due to low 4-CP contents in the aeration tank yielding negligible inhibition effects and low maintenance requirements. The sludge volume index (SVI) decreased with increasing HRT up to 15 h due to high biomass concentrations at high HRT levels resulting in well settling sludge with low SVI values. Hydraulic residence times above 15 h resulted in more than 90% COD and complete 4-CP and toxicity removals along with well settling sludge.