Kinetics and mechanism of hexavalent chromium removal by basic oxygen furnace slag

Basic oxygen furnace slag(BOFS) has the potential to remove hexavalent chromium(Cr(VI))from wastewater by a redox process due to the presence of minerals containing Fe2+. The effects of the solution p H, initial Cr(VI) concentration, BOFS dosage, BOFS particle size, and temperature on the removal of Cr(VI) was investigated in detail through batch tests. The chemical and mineral compositions of fresh and reacted BOFS were characterized using scanning electron microscope(SEM) equipped with an energy dispersive spectrometer(EDS)system and X-ray diffractometer(XRD). The results show that Cr(VI) in wastewater can be efficiently removed by Fe2+released from BOFS under appropriate acidic conditions. The removal of Cr(VI) by BOFS significantly depended on the parameters mentioned above. The reaction of Cr(VI) with BOFS followed the pseudo-second-order kinetic model. Fe2+responsible for Cr(VI) removal was primarily derived from the dissolution of Fe O and Fe3O4 in BOFS. When H2SO4 was used to adjust the solution acidity, gypsum(Ca SO4·2H2O)could be formed and become an armoring precipitate layer on the BOFS surface, hindering the release of Fe2+and the removal of Cr(VI). Finally, the main mechanism of Cr(VI) removal by BOFS was described using several consecutive reaction steps.     

树脂负载草酸铁光助类芬顿降解水中孔雀石绿

为了强化多相类芬顿反应的速率,在可见光下采用以草酸盐为配体的三价铁草酸络合物(Fe~(3+)C_2O_4/R)为催化剂催化过氧化氢降解水中孔雀石绿.结果表明,与Fe~(3+)/R相比催化剂Fe~(3+)C_2O_4/R具有更强的催化活性,能强化羟基自由基(·OH)的产生. 过氧化氢的初始浓度越高,反应速率越快,反应遵循一级反应动力学,反应速率常数与过氧化氢浓度具有很好的相关性.在pH值3～9的范围内,催化剂Fe~(3+)C_2O_4/R都能有效地对MG进行降解,最佳pH值为6.随着催化剂投量的增加,MG的去除效率明显提高.随着MG初始浓度的增加,MG的去除也由吸附为主转化为以氧化为主,但总体影响不大.催化剂重复使用后仍然具有较好的催化活性,说明铁在树脂表面负载比较牢固,催化剂具有反复使用的能力.反应中的氧化活性物种是羟基自由基和高价态铁同时共存.     

均相Fenton法处理干法腈纶废水工艺优化与分析

采用均相Fenton法处理干法腈纶废水,并通过单因素试验和基于中心组合设计的响应面法考察了H2O2投加量、Fe2+投加量、初始pH值及反应时间的影响及其交互作用.同时,建立了以COD去除率为响应值的二次响应曲面模型,并采用方差分析对模型进行了验证.结果表明,影响COD去除效果的各因子显著性顺序依次为:Fe2+投加量>H2O2投加量>初始pH值>反应时间;Fe2+投加量与初始pH值的交互作用最为显著;反应最优组合条件为:H2O2投加量90.0mmol.L-1,Fe2+投加量30.0mmol.L-1、初始pH值3.1,反应时间113.6min,该条件下COD去除率为47.1%,与模型预测值48.5%基本一致.     

Decontamination of alachlor herbicide wastewater by a continuous dosing mode ultrasound/Fe2+/H2O2 process

We used a ultrasound/Fe2+/H2O2 process in continuous dosing mode to degrade the alachlor.Experimental results indicated that lower pH levels enhanced the degradation and mineralization of alachlor. The maximum alachlor degradation(initial alachlor concentration of 50 mg/L) was as high as 100% at pH 3 with ultrasound of 100 Watts, 20 mg/L of Fe2+, 2 mg/min of H2O2 and 20℃ within60 min reaction combined with 46.8% total organic carbon removal. Higher reaction temperatures inhibited the degradation of alachlor. Adequate dosages of Fe2+and H2O2 in ultrasound/Fe2+/H2O2process not only enhance the degradation efficiency of alachlor but also save the operational cost than the sole ultrasound or Fenton process. A continuous dosing mode ultrasound/Fe2+/H2O2 process was proven as an effective method to degrade the alachlor.     

均相Fenton法深度处理丙烯腈生化尾水

采用均相Fenton法深度处理丙烯腈生化处理工艺尾水,通过单因素法分析了H_2O_2投加量、Fe~(2+)投加量、初始p H值和反应时间对尾水COD去除率的影响;并采用中心响应曲面法优化Fenton处理的工艺参数,得到最佳反应条件为:Fe~(2+)投加量为1.02 mmol·L-1,H_2O_2投加量为11.13 mmol·L~(-1),初始pH值为3.66,反应时间为105 min,COD去除率达到61.1%.处理后尾水COD值低于50 mg·L~(-1),可满足石化行业一级排放标准.Fenton工艺对尾水中特征污染物均有较好的去除效果,最佳反应条件下丙烯腈、间苯二甲腈、3-氰基吡啶的去除率分别为99.5%、97.6%、73.7%;Fenton法对3种特征污染物的降解能力从大到小依次为:丙烯腈间苯二甲腈3-氰基吡啶.三维荧光光谱分析表明,尾水中存在大量类富里酸荧光物质,其中,紫外区类富里酸含量最高,Fenton工艺在较短反应时间和较少的试剂投加量条件下,便可有效地去除这类难降解物质.     

Ce3+与Cu2+协同强化芬顿体系氧化苯酚的效能与机制研究

研究了Ce~(3+)与Cu~(2+)协同强化芬顿体系在不同初始条件下对水中苯酚的氧化效能与机制.结果表明,在p H适用范围的宽度和H_2O_2浓度变化方面,Ce~(3+)/Cu~(2+)/Fe~(2+)/H_2O_2体系比传统的芬顿体系更具有优势,该体系在p H=5.0、H_2O_2浓度为2.0mmol·L-1的条件下,仍可以对苯酚保持相对较高的氧化效能;Cu~(2+)可能会借助反应过程中的中间产物(醌类物质)生成Cu+,Cu+催化H_2O_2分解生成·OH,Ce~(3+)可能促进体系内醌类物质的形成,加快Fe~(3+)与Fe~(2+)的循环效能,在一定程度上提高了芬顿体系中H_2O_2分解生成·OH的速率,说明Cu~(2+)与Ce~(3+)对芬顿体系的强化作用具有协同性;自由基终止剂依然可以抑制Ce~(3+)、Cu~(2+)强化的芬顿体系对苯酚的降解,由此说明体系中起到氧化作用的活性物种仍然是羟基自由基(·OH).     

UV/PMS降解水中罗丹明B的动力学及反应机理

采用紫外(UV)活化过硫酸氢钾(PMS)产生强氧化性硫酸根自由基(SO_4~·-)降解人工染料罗丹明B(RhB).考察了溶液初始p H、氧化剂剂量、RhB初始浓度、天然有机物(NOM)、Fe~(2+)浓度、自由基淬灭剂(甲醇和叔丁醇)及水体中常见阴离子对降解效果的影响,并探测反应体系中生成的无机阳离子及小分子有机酸的种类和浓度.结果表明,降解反应遵循准一级反应动力学,其降解速率受到溶液初始pH的显著影响,当溶液酸性越强或碱性越强时,RhB的降解效果越好,且酸性条件下降解效果优于碱性条件.同时,加大氧化剂剂量及降低底物浓度也会对RhB的降解起促进作用.体系中投加过渡金属Fe~(2+)可显著促进RhB的降解效果,当Fe~(2+)与PMS的浓度比为1∶1时,降解效果最佳.水体中的NO_3~-对RhB的降解有着显著的促进作用,而H_2PO_4~-、C_2O_4~(2-)、Cl~-和NOM则对RhB的降解有抑制作用.采用离子色谱分析了UV/PMS体系降解RhB所产生的NH_4~+,以及甲酸、乳酸、乙酸和草酸,推测RhB在UV/PMS体系中的降解主要是通过共轭结构的破坏、N-位脱乙基并伴有苯环结构的破坏进行的.综合分析表明,UV/PMS工艺可有效运用于罗丹明B污染水体的修复处理过程.     

酸性条件下黄铁矿氧化机制的研究

以黄铁矿粉末制备成的碳糊电极为工作电极,利用循环伏安曲线和极化曲线等电化学手段,对酸性条件下黄铁矿的氧化过程和机制进行了研究.结果表明,黄铁矿的氧化主要包括以下两个过程:首先,黄铁矿(FeS2)矿物晶格中的Fe2+溶出而被氧化为Fe3+,此过程会伴随有如硫单质、缺铁硫化物(Fe1-xS2)和多硫化物(FeSn)等氧化中间产物的生成,覆盖在黄铁矿的表面而形成一层钝化膜,阻碍了其氧化溶解过程;接着,黄铁矿表面的钝化膜被进一步氧化为可溶性的SO24-.在酸性条件下,黄铁矿氧化反应的最终产物为Fe3+和SO24-.另外,在所研究的酸度范围内,随着H2SO4溶液浓度的增大,体系的开路电位和腐蚀电位均正移,氧化和还原的峰电流值升高,腐蚀电流增大,说明增加体系的酸度会促进黄铁矿的氧化过程.     

Fe/Zn-TMS体系吸收去除催化裂化干气中H2S的性能

本研究采用FeCl3·6H2O、ZnCl2和环丁砜(TMS)复配形成的Fe/Zn-TMS体系脱除催化裂化(FCC)干气中的H2S,并用30%H2O2氧化再生Fe/Zn-TMS体系.同时,研究了各活性成分比例、吸收液体积浓度、吸收液pH值等对脱硫效率的影响,以及H2O2用量、吸收富液pH值对Fe2+氧化率的影响.结果表明,n(FeCl3·6H2O)∶n(ZnCl2)∶n(TMS)为0.45∶0.55∶1,吸收液pH为0.75,体积浓度(W)为50%的条件下能长时间高效脱硫,最高脱硫率达99.9%;在n(Fe2+)∶n(H2O2)为2∶1,吸收富液pH为0.65的条件下,Fe2+氧化率达96.7%.体系可循环使用3次,且能耗低、操作简单.     

纳米Fe3O4/H2O2降解诺氟沙星

采用纳米Fe3O4催化H2O2氧化降解水环境中的诺氟沙星.考察了溶液酸度、温度、催化剂和H2O2浓度对诺氟沙星降解的影响,对比不同底物在Fe3O4/H2O2体系中的降解情况,并进一步探讨了其反应机制.结果表明,溶液酸度显著影响诺氟沙星的降解率,在酸性条件下（pH=3.5）诺氟沙星的降解效率最高.诺氟沙星的降解率随纳米F...     

Magnetically recoverable Fe3O4@polydopamine nanocomposite as an excellent co-catalyst for Fe3+ reduction in advanced oxidation processes

Advanced oxidation processes are widely applied to removal of persistent toxic substances from wastewater by hydroxyl radicals(·OH),which is generated from hydrogen peroxide(H_2O_2) decomposition.However,their practical applications have been hampered by many strict conditions,such as iron sludge,rigid pH condition,large doses of hydrogen peroxide and Fe~(2+),etc.Herein,a magnetically recyclable Fe_3O_4@polydopamine(Fe_3O_4@PDA) coreshell nanocomposite was fabricated.As an excellent reducing agent,it can convert Fe~(3+)to Fe~(2+).Combined with the coordination of polydopamine and ferric ions,the production of iron sludge is inhibited.The minimum concentration of hydrogen peroxide(0.2 mmol/L and Fe~(2+)(0.18 mmol/L)) is 150-fold and 100-fold lower than that of previous reports,respectively.It also exhibits excellent degradation performance over a wide pH range from 3.0 to 9.0.Even after the tenth recycling,it still achieves over 99% degradation efficiency with the total organic carbon degradation rate of 80%,which is environmentally benign and has a large economic advantage.This discovery paves a way for extensive practical application of advanced oxidation processes,especially in environmental remediation.     

Fluoride removal by Al, Ti, and Fe hydroxides and coexisting ion effect

Batch experiments were conducted to evaluate fluoride removal by Al,Fe,and Ti-based coagulants and adsorbents,as well as the effects of coexisting ions and formation of aluminum–fluoride complexes on fluoride removal by co-precipitation with alum(Al_2(SO_4)_3·18H_2O).Aluminum sulfate was more efficient than the other coagulants for fluoride removal in the pH range between 6 and 8.Nano-crystalline TiO_2 was more effective for fluoride removal than Al and Fe hydroxides in a pH range of 3–5.Coexisting anions in water decreased the removal of fluoride in the order:phosphate(2.5 mg/L) arsenate(0.1 mg/L) bicarbonate(200 mg/L) sulfate(100 mg/L) = nitrate(100 mg/L) silicate(10 mg/L) at a pH of 6.0.The effect of silicate became more significant at pH 7.0.Calcium and magnesium improved the removal of fluoride.Zeta-potential measurements determined that the adsorption of fluoride shifted the PZC of Al(OH)_3 precipitates from 8.9 to 8.4,indicating the chemical adsorption of fluoride at the surface.The presence of fluoride in solution significantly increased the soluble aluminum concentration at pH 6.5.A Visual MINTEQ modeling study indicated that the increased aluminum solubility was caused by the formation of AlF~(2+),AlF~(+2),and AlF_3complexes.The AlF_x complexes decreased the removal of fluoride during co-precipitation with aluminum sulfate.     

Fenton氧化去除制药企业活性污泥中AOX的效果研究

用Fenton氧化处理合成制药企业活性污泥混合液,考察了不同Fe~(2+)、H_2O_2投加量和不同反应时间下污泥与上清液中AOX(可吸附有机卤代物)的去除效果,优化了反应条件,探讨了氧化机制.结果表明,Fenton氧化的最佳条件为H_2O_2投加量0.90 mol·L~(-1),Fe~(2+)投加量0.045 mol·L~(-1)[物质的量比为:n(Fe~(2+))∶n(H_2O_2)=1∶20],反应2 h,污泥和上清液中AOX可分别去除70.7%和78.5%.GC-MS分析结果显示,污泥中含有11种有机卤代物,Fenton氧化后有8种不再检出;3种仍有检出,但浓度有所降低,去除率约为40%~50%.与此同时,污泥中对二甲苯、邻苯二甲酸二异丁酯等非有机卤代物类有毒有害有机物也得到有效去除.     

Removal of Cs from water and soil by ammonium-pillared montmorillonite/Fe3O4 composite

To remove cesium ions from water and soil, a novel adsorbent was synthesized by following a one-step co-precipitation method and using non-toxic raw materials. By combining ammonium-pillared montmorillonite (MMT) and magnetic nanoparticles (Fe₃O₄), an MMT/Fe₃O₄ composite was prepared and characterized. The adsorbent exhibited high selectivity of Cs⁺ and could be rapidly separated from the mixed solution under an external magnetic field. Above all, the adsorbent had high removal efficiency in cesium-contaminated samples (water and soil) and also showed good recycling performance, indicating that the MMT/Fe₃O₄ composite could be widely applied to the remediation of cesium-contaminated environments. It was observed that the pH, solid/liquid ratio and initial concentration affected adsorption capacity. In the presence of coexisting ions, the adsorption capacity decreased in the order of Ca^2 + > Mg^2 + > K⁺ > Na⁺, which is consistent with our theoretical prediction. The adsorption behavior of this new adsorbent could be expressed by the pseudo-second-order model and Freundlich isotherm. In addition, the adsorption mechanism of Cs⁺ was NH₄⁺ ion exchange and surface hydroxyl group coordination, with the former being more predominant.     

铁刨花-Fenton-絮凝工艺对染料生产废水中AOX、色度和TOC的去除效果研究

采用铁刨花-Fenton-絮凝工艺处理染料生产废水,考察了不同Fe~(2+)与H_2O_2摩尔比(1∶3~1∶15)、铁刨花反应时间(2~5h)、Fenton氧化反应时间(20~80 min)下可吸附性有机卤代物(AOX)、色度和总有机碳(TOC)的去除效果.结果表明,AOX、色度和TOC去除率随Fe~(2+)与H_2O_2摩尔比的降低先升高后减少,随铁刨花和Fenton反应时间的增加而持续升高.最优化条件为Fe~(2+)与H_2O_2摩尔比1∶8、铁刨花反应时间4 h和Fenton反应时间60 min,该条件下AOX、色度和TOC的去除率分别为94.2%、93.7%和27.2%.比较实验结果表明,铁刨花-Fenton-絮凝组合工艺对废水AOX、色度和TOC的去除效果远优于铁刨花处理、Fenton氧化、絮凝沉淀的单个技术或两两技术组合效果.GC-MS分析表明,废水中的有机卤代物和苯胺类污染物得到高效去除,此外硝基苯类、苯酚类、苯甲醛类、醚类、腈类和杂环化合物等有毒有害物质也均得到高效去除.叔丁醇捕获·OH实验表明·OH在Fenton反应中的主导作用.     

纳米零价铜活化分子氧降解水中恩诺沙星

采用纳米零价铜(nanoscale zero-valent copper,nZVC)活化分子氧对水中恩诺沙星(enrofloxacin,ENR)的去除进行了系统研究.通过表征可以发现,纳米铜粉比表面积高于微米级铜粉,无孔隙结构,表面粗糙且容易团聚.纳米级ZVC活化分子氧的性能明显优于微米级ZVC,这主要归因于其较大的比表面积,更容易被腐蚀.通过探究活化机制可以发现,活化分子氧产生的H_2O_2和表面腐蚀产生的Cu+构成了新型类Fenton体系,持续释放的羟基自由基是造成水中ENR高效去除的主导活性物种;同时,反应过程中产生的超氧自由基能够促进Cu2+还原成Cu+,从而加速ENR的去除过程.反应条件对nZVC活化分子氧降解ENR有一定的影响,较高的nZVC投加量、较低ENR浓度、较高的反应温度以及强酸性条件均有利于ENR的去除.     

水合氧化铝负载的磁性核/壳结构Fe3O4@SiO2纳米颗粒对水中磷的去除及再利用

在磁铁矿纳米颗粒表面包被硅壳后再包被水合氧化铝,制备了具备核壳结构的磁性纳米颗粒除磷吸附剂(磁性氧化铝),通过XRD、TEM、VSM、BET比表面积测定进行了表征.XRD和TEM结果显示了核壳结构的存在,其饱和磁化强度达56.00 emu·g~(-1),比表面积达47.27 m~2·g~(-1).Langmuir模型计算的磷最大吸附量为12.90 mg·g~(-1),且在25℃和50℃下均保持稳定,反应快速,40min磷去除率达96%以上.磁性纳米吸附剂对磷的吸附与pH关系密切,在p H为5~9时磷去除率达90%以上.采用实际污水实验,最佳投量为1.25 kg·t~(-1).吸附-脱附-再生实验结果表明,磷吸附率随循环次数增加稍有下降,吸附的磷可以通过1 mol·L~(-1)的NaOH脱附,脱附率为90%左右,且吸附剂可以进行再生,具有反复利用和回收磷资源的潜力.     

双极电化学氧化降解水中苯胺

采用钛基氧化物涂层材料（Ti/SnO2-Sb2O5）为阳极,石墨为阴极,在含Fe2＋和不含Fe2＋2种电解质条件下研究了苯胺的电化学氧化降解效率和机制.结果表明,Ti/SnO2-Sb2O5阳极氧化降解有机物的电位约2.0 V±0.1 V,而石墨阴极还原O2生成H2 O2的优化电位为-0.65 V.H2 O2单独作用不能...     

基于反硝化脱氮的硫铁复合填料除磷机制

为提高硫铁复合填料反硝化脱氮同步除磷效果,对比研究了不同填料和耦合微生物后的除磷效果,分析了微生物耦合硫铁复合填料反硝化脱氮同步实现除磷的机制.结果表明与单纯海绵铁填料比较,硫磺与海绵铁复合填料除磷效率提高30%,达到95%以上,出水磷含量可降至0.1 mg·L~(-1)以下.X射线衍射(XRD)和总铁浓度分析表明,硫铁复合填料除磷系统反应产物主要为FeOOH、FeS和Fe_4(PO_4)_3(OH)_3固体物质和溶解性铁离子,产生于海绵铁的腐蚀和除磷过程;腐蚀产生的Fe~(2+)及Fe~(3+)的水解产物FeOOH和Fe S通过吸附沉淀作用将PO_4~(3-)转化为Fe_4(PO_4)_3(OH)_3去除.微生物耦合硫铁炭复合填料反应器运行稳定后,TN、TP去除率分别在90%左右和83%以上;硫自养反硝化产生的H~+和生物铁作用也可以促进海绵铁腐蚀和除磷过程,体系将"异养协同自养"复合反硝化与化学除磷有机结合,实现了城市污水处理厂尾水高效反硝化脱氮同步除磷的目的.     

羟基磷灰石-四氧化三铁-沸石复合材料制备及去除水中刚果红研究

采用可溶性磷酸盐、钙离子、二价铁离子、三价铁离子和天然沸石等材料制备了羟基磷灰石-四氧化三铁-沸石(HAPFe3O4-沸石)复合材料,对该复合材料进行了表征,并考察了该复合材料对水中刚果红的吸附作用.结果表明,HAP-Fe3O4-沸石复合材料对水中的刚果红具备良好的吸附能力.当pH由3增加到4或由7增加到11时,HAP-Fe3O4-沸石复合材料对水中刚果红的去除能力下降;当pH由4增加到7时,对刚果红的吸附能力基本保持不变.HAP-Fe3O4-沸石复合材料对水中刚果红的去除率随吸附剂投加量的增加而增加,而对水中刚果红的单位吸附量则随吸附剂投加量的增加而降低.HAP-Fe3O4-沸石复合材料对水中刚果红的吸附动力学过程可以较好地采用准二级动力学模型加以描述,对刚果红的吸附平衡数据可以采用Langmuir和Freundlich等温吸附模型加以描述.根据Langmuir模型确定的最大吸附容量为117 mg·g-1.(pH 7和303 K).HAP-Fe3O4-沸石复合材料对水中刚果红的吸附是自发吸热并伴随熵增加的过程.当pH为7时,HAP-Fe3O4-沸石复合材料吸附水中刚果红的主要机制包括表面配位作用、氢键作用以及路易斯酸碱反应.采用热再生的方法可以使吸附刚果红后的HAP-Fe3O4-沸石复合材料得到再生,热再生后的复合材料可以循环使用并且对水中刚果红的吸附性能良好.X射线衍射分析结果表明HAP-Fe3O4-沸石复合材料含Fe3O4,磁滞回线结果表明HAP-Fe3O4-沸石复合材料具备较高的磁饱和强度,复合材料吸附刚果红后可以很容易地通过外加磁场的作用快速地与水溶液分离.结果表明,HAP-Fe3O4-沸石复合材料适合作为一种吸附剂去除废水中的刚果红.