首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 203 毫秒
1.
为防治采空区遗煤浸水后引发的自燃火灾,制备褐煤原煤及浸水煤煤样,进行程序升温试验,测试煤样的傅里叶变换红外(FT-IR)光谱,并通过分区拟合分析浸水对煤分子结构的影响。结果表明:浸水煤的失水结束点温度、着火温度和最大失重速率点温度较原煤均有不同程度的提前,着火活化能降低了11. 2%,说明浸水煤更容易发生自燃;浸水后煤中烷基醚、芳基醚、亚甲基以及自缔合羟基氢键等基团含量升高,导致煤体活性增强。  相似文献   

2.
为了深入探究矿井下伴生硫化物对煤自燃及着火燃烧特性的影响,向原煤中添加不同量的含硫物配制4种不同含硫量的煤样,通过TG实验、DSC测试和XRD分析,研究伴生硫化物对煤自燃及着火燃烧特性的影响规律;基于Coats-Redfern法计算煤中掺加不同伴生硫化物时煤燃烧阶段的活化能。研究结果表明:随着煤中掺比伴生硫化物的增多,煤的特征温度相应减小,而吸氧量、可燃和稳燃指数相应增大,原煤中混入伴生硫化物后更易自燃;随着煤中掺比伴生硫化物的增多,煤燃烧阶段的活化能降低,煤更易着火燃烧;伴生硫化物的主要成分为水绿矾、叶绿矾,这些物质在常温下遇水和氧气能够发生化学循环反应,反应放热促使了煤更易自燃;伴生硫化物在温度高于200℃以后整体表现为放热,在温度为565℃时达到放热峰值,这使得煤燃烧阶段的活化能降低,煤更易燃烧。  相似文献   

3.
为研究不同煤质煤尘的着火性能,首先,选取不同矿区9种煤样,分析其水分、挥发分、灰分、固定碳煤等工业成分;然后开展煤尘云最低着火温度试验;最后,对工业分析指标和煤尘云最低着火温度进行统计学和灰色关联分析。结果表明:煤样的最低着火温度介于405~515℃,着火温度值差异较大;煤的工业分析指标均与最低着火温度呈现出较强相关性:挥发分和固定碳含量与最低着火温度负相关,灰分和水分含量与最低着火温度呈正相关,即挥发分含量、固定碳含量越高,煤尘越易出现着火现象,灰分含量、水分含量越高,煤尘越不易着火;挥发分含量与最低着火温度关联度最大。  相似文献   

4.
粉尘爆炸事故统计表明,部分爆炸事故的发生是由于生产设备最高容许温度超过或达到了粉尘云的最低着火温度.通过大量文献调研,对近40年粉尘云的最低着火温度的实验与理论研究进行了分析,并根据目前工业生产实际存在的问题提出了新时期研究复杂条件下着火温度的必要性.同时,应在此基础上建立数学模型并利用数值分析验证实验结果,以便工业应用.  相似文献   

5.
为了研究碱性水对煤自燃特性的影响,选取葫芦素煤矿102工作面煤样作为实验煤样,利用STA-449C型同步热分析仪进行热重实验,研究加入PH=8 NaOH的煤样与原煤以及加入蒸馏水煤样在空气氛围中燃烧失重、放热量、特征温度点等变化规律,并根据Coats-Redfern积分模型计算了3种煤样燃烧反应动力学参数(活化能、指前因子)。研究结果表明:加入碱性水的2号煤样失重量较1,3号少,燃烧失重速率更低;2号煤氧化燃烧温度区间缩短,着火温度点升高,放热量少,比1,3号煤分别少485.0,480.4 J/g;3种煤样反应机理基本遵循一级化学反应函数,2号煤各段活化能高于1,3号煤,但2号煤失水活化能小于3号,表明碱性水具有抑制煤自燃效应。  相似文献   

6.
为了了解不同配风工况对煤粉燃烧过程的影响,本文以四角切圆燃烧煤粉锅炉为研究对象,采用k-ε-f-g即混即燃气相燃烧模型与煤的双挥发反应热解模型对不同工况下炉内流动、燃烧等过程进行了数值模拟。其结果表明:当机组负荷一定时,适当减少一次风率使整个炉膛火焰充满度大大得到改善,火焰长度与煤粉着火距离有所缩短;采用倒宝塔型二次风配风方式对于较差煤种的稳定着火较为有利;而停止三次风时,炉膛温度水平较高,煤粉燃烧完全,锅炉效率有所提高。  相似文献   

7.
<正>燃煤粉锅炉,主要适用于燃烧反应低的无烟煤和贫煤的混合煤质,其结构与常规燃煤锅炉不同,易于实现燃烧过程的多级配风。即可控制着火阶段的着火温度,又可加强燃烧后的混合,促进低反应燃料的燃烬,这样强化了稳燃条件,在烧无烟煤和贫煤的混合煤时,最低不投油稳燃负荷可达到40%~55%。由于煤粉炉火焰是下行然后迂回,因此火焰中心就在煤粉喷口附近,这样就形成了一个高温回流区,易于劣质煤的着火,利于稳燃。但燃烧调节较复杂,如调节不当,易在受热面处结焦积渣。造成不必要的热损失,严重者造成锅炉灭火。  相似文献   

8.
利用热重试验对粒径小于0.2 mm的长焰煤煤粉进行了不同氧体积分数(21%、40%、50%、60%和80%)和升温速率(20℃/min、30℃/min、40℃/min、50℃/min和60℃/min)的25种工况下煤氧复合过程中热解特性的测定,分析了两种因素对各特征值的影响。结果表明:以热失重速率为基准,长焰煤在含氧气氛下的热解过程可分为失水失重阶段、氧化增重阶段及着火、燃烧和炭化3个阶段;通用着火特性指标越大,煤样燃烧特性越好,自燃点越小,煤样工业分析结果应与其实际生产过程中的自燃危险性相结合;升温速率不变时自燃点随氧体积分数上升而下降,而煤氧复合时间随氧体积分数上升呈现先降低再微弱增加的趋势;氧体积分数一定时自燃点随升温速率上升而上升,煤氧复合时间则随之下降。对自燃点及煤氧复合时间进行均值无量纲化,并将其与无量纲化升温速率进行拟合,决定系数(R~2)约为1.0;提出了煤氧复合难易程度参数(D),计算结果表明,即使自燃点随升温速率上升发生滞后,煤氧复合难度仍然减弱。  相似文献   

9.
为研究不同煤质的煤尘层最低着火温度特性及其影响因素,选取褐煤、长焰煤、不粘煤、气煤、焦煤、瘦煤、贫煤和无烟煤8种不同变质程度的煤尘样品,测试分析8种煤尘层的最低着火温度及最低着火温度工况下煤尘层着火类型、着火时间,并研究了粒径和煤尘层厚度对煤尘层最低着火温度的影响。结果表明,随变质程度由褐煤逐渐增大,最低着火温度T_L由290℃不断增大。褐煤、长焰煤、不粘煤和气煤为a类着火,其着火时间较为接近,均值为19. 5 min,而焦煤、瘦煤和贫煤为c类着火,着火时间均值为11 min,表明随变质程度增大,虽然TL增大,但着火时间明显缩短。通过分析最低着火温度工况下不同煤质的温度T-时间t变化情况,认为褐煤、长焰煤、不粘煤和气煤煤尘层温度曲线中出现明显上下波动现象,是因为煤尘层厚度有限,无法长时间积聚能量。通过构建TL与粒径r、煤尘层厚度d的三维空间拟合模型,发现粒径小、厚度大的煤尘层具有更大的着火敏感性和爆炸潜伏性,更应加强防范。  相似文献   

10.
为研究半煤岩巷道中岩粉质量分数和煤的挥发分与煤岩混合型粉尘云最低着火温度的关系,选取挥发分差异较大的5种煤样以相同比例配制煤岩混合型粉尘,利用粉尘云最小点火温度测定仪进行煤岩混合型粉尘试验。结果表明,当煤岩混合型粉尘中岩粉质量分数低于40%时,岩粉的混合会导致混合型粉尘云最低着火温度发生小幅度波动;当岩粉质量分数高于40%时,煤岩混合型粉尘最低着火温度会随岩粉质量分数的增加而大幅度升高;挥发分质量分数越小的煤粉,其混合型粉尘云最低着火温度越容易受岩粉质量分数的影响。  相似文献   

11.
The temperature at which coal dust glows is normally much lower than the auto-ignition temperature (AIT) of methane/air mixtures, and thus a better understanding is needed regarding methane/air ignition in a heated environment in the presence of coal particles. A horizontal tube apparatus was used to test the effect of brown coal and two kinds of bituminous and anthracite on methane/air combustibility. For the four coal samples tested, the presence of coal particles significantly reduced the minimum temperature for ignition of methane/air mixtures in a heated environment. No. 1 bituminous coal with 12 mm diameter decreased the ignition temperature value from 595 to 500 °C. It is thought that pre-ignition of low-AIT volatiles emitted from the heated coal particles ignited the methane/air mixtures. Volatiles, sulfur content, and large porosity of piled coal particles all enhanced ignition of methane/air mixtures in a hot environment, while water content and small particle size reduced ignition. For anthracite, no ignition occurred when temperatures of the heated environment were lower than the AIT of methane (595 °C), except for the 12-mm-diameter sample. Anthracite did not readily ignite methane/air mixtures and the ignition mechanism was somewhat similar to that of a burning cigarette.  相似文献   

12.
为准确判断煤燃点,提高煤自燃灾害防治能力,依据热爆炸理论,结合煤自燃过程放热曲线,将煤自燃升温过程中微分热流曲线上第1处极小值点作为煤的燃点,计算煤着火前后放热过程动力学参数变化.结果表明:随升温速率增加,煤自燃反应放热过程逐渐向高温区域移动,煤燃点逐渐增大,反应的活化能逐渐减小;同一升温速率下燃点之后煤的活化能增大;...  相似文献   

13.
基于活化能指标的煤自燃倾向性及发火期研究   总被引:2,自引:0,他引:2  
在煤的自燃及热分析动力学的基础上,结合对神东矿区3种煤样进行了热重实验,运用热重分析手段对煤从常温到燃点之间的氧化热解过程进行了研究。运用不同动力学机制模型函数分别对热重分析数据进行了处理和相关性分析,结果表明煤炭氧化热解过程符合一级化学反应动力学机制,据此求出活化能等动力学参数。对基于活化能指标的煤的自燃倾向性及自然发火期进行了初步研究。经过研究发现,该方法是科学的、客观的。  相似文献   

14.
This paper reports the results of experiments done to examine the explosibility of pulverized fuel dusts (two different coals and petroleum coke) and their waste products (bottom and fly ashes). Tests were conducted for the fuel dusts alone and also blended with other fuels and ashes. The explosion parameters of interest were maximum pressure and rate of pressure rise, and ignition energy and temperature. Petroleum coke was found to present a lesser explosion hazard than the coals. Admixture of either coal or petroleum coke with fly ash resulted in explosible mixtures at volatile contents dependent on the composition of the mixture components and their particle sizes.  相似文献   

15.
实验测定了林西矿肥煤样品30~900℃煤自燃全过程热动力学特征参数,得出:TG/DTG曲线显示煤样DTG初始临界温度45℃,干裂温度122℃,活性温度195℃,增速温度265℃,质量极大值温度342℃,着火温度465℃,最大热失重速率温度515℃和燃尽温度690℃;DSC曲线显示,煤样初始放热温度60℃、最大热释放速率温度511℃。结合TG-DTG-DSC曲线综合分析可知,煤温达到510℃左右时煤样反应最剧烈。由煤自燃标志气体测定实验系统得出:煤温130℃后CO,CO 2释放量迅速增加,210℃增加速度下降;CH 4,C 2 H 6含量变化具有规律性且两者变化相近;C 2 H 4出现温度为130℃;C 2 H 4/C 2 H 6比值在190~350℃有较强的规律性,呈上升趋势且上升速度较快;350℃之后,CH 4,C 2 H 6,C 2 H 4体积分数均开始急剧增大;C 2 H 4/CO与C 2 H 4/CO 2变化趋势大致相同,在130~350℃时缓慢增长,达到350℃后比值呈指数形式上升。经拟合曲线,得到活化能的3个突变点温度:70,180,220℃,其中180℃与交叉点温度相吻合。通过以上研究,得到了肥煤自燃全过程的热力学特征参数,为实际生产中防治煤自燃提供了理论依据。  相似文献   

16.
The Mediterranean area is responsible for about 98% of the olive oil worldwide production, with 900 million olive trees occupying 10 million hectares. However, the processing of 100 kg of olives leads to the production of 40 kg of wastes, mainly constituted by olive pomace, which is potentially recoverable as energetic or material source. In general, in the past 20 years, the exploitation of olive pomace has increased, but along with it, the need for further information about its chemical-physical characterization and the related hazard in industry. Thus, a risk analysis assessment was conducted. When pelletized or in chunks, olive pomace does not pose any greater hazard than a pile of woody material, but when pulverized, it might become dangerous. Two parallel series of experiments were carried out at Dalhousie University (Lab 1) and at Polytechnic of Turin (Lab 2) using the same olive pomace sample, according to slightly different experimental procedures. Olive pomace dust explosibility and flammability parameters were measured: minimum ignition energy (MIE), minimum ignition temperature (MIT), maximum pressure rise rate ((dP/dt)max and KSt), maximum pressure (Pmax), and minimum explosible concentration (MEC). Moreover, the chemical and physical characterization of olive pomace was carried out: moisture content, particle size analysis, Scanning Electronic Microscope (SEM) investigation, thermo-gravimetric analysis (TGA), solid-state Nuclear Magnetic Resonance (NMR), mass spectrometry, calorific value, and bulk density estimation. Different thermal behaviors were observed according to the sieving/grinding pre-treatment. As concern flammability tests, samples seemed not to be sensitive to electric arc ignition (a value of MIE could not be measured), while coarser samples demonstrated higher ignition sensitivity to hot environment sources (MIT furnace) than finer ones. On the other hand, explosion violence parameters were enhanced by decreasing the particle size, while peak pressures were significantly influenced by the heat of combustion and the moisture content. Finally, a new test was developed to quantify the propensity of the raw material to produce fines by abrasion. It is defined “Abrasion by Rolling Test” (ART). The properties of the fines produced were measured as well.  相似文献   

17.
为研究煤层及腐朽坑木着火特性,采集巷道内腐朽坑木与煤样并进行混合,对其混合物进行燃点测定和程序升温实验;通过对不同煤木混合物在升温过程中产生气体的规律性进行分析,优选出混合物产生的单一气体指标及复合指标.研究结果表明:随朽木在混合物中的比例上升,混合物燃点呈下降趋势,且CO,C2 H4等指标气体出现更早,CO产生量更大...  相似文献   

18.
Investigation of explosion characteristics of coal dust was undertaken as a part of regular research program at CSIR-CBRI, Roorkee, India, for designing explosion safety measures for coal dust handling installations. This paper presents results of detailed experimental work on determination of Limiting Oxygen Concentration (LOC) and influence of reduced oxygen levels on explosion severity data for two types of coals with varying volatile matter as 27.18% (coal A) and 19.69% (coal B) from Jharia coalfield of India determined at ambient conditions with 20-L Spherical Vessel established at CSIR-CBRI. The effects of coal particle size and moisture content were evaluated. Data presented will be used for hazard analysis, designing explosion preventive measures, and explosion severity reduction by involving the use of inert gases for installations handling pulverized coal with similar nature. The importance of ignition source energy in determining LOC data is highlighted. The data collected lead to an extension of the current data for coal dusts as found in the literature. Limiting oxygen concentrations were found as 7% for coal A and 8% for coal B for the size representative to that used in pulverized coal boilers and moisture content ~4%.  相似文献   

19.
为研究煤油共生矿区含油煤尘最低着火温度的变化规律,选取3种含油浓度不同的煤样,采用粉尘云最低着火温度测定系统,研究含油煤尘云最低着火温度随含油浓度、喷尘压力及煤尘质量的变化规律。研究结果表明:含油煤尘的最低着火温度较不含油煤尘显著降低,且随着煤尘含油浓度的增加,煤尘中挥发分含量增多,煤尘云最低着火温度降低,爆炸危险性增强;低含油浓度煤尘,煤尘受原油挥发分影响较大,在含油浓度为5.7%,4.3%且质量浓度为1364~4550 g/m3时煤尘云最低着火温度随喷尘压力的增大呈先增大后减小的变化趋势,在5.7%,4.3%含油浓度且喷尘压力为0.05 MPa时煤尘MIT随煤尘质量浓度增加先降低后缓慢升高。高含油浓度煤尘,受煤尘团聚现象影响较大,煤尘云最低着火温度随喷尘压力的增加而升高,随煤尘质量的增加呈先减小后增大再缓慢减小的变化规律。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号