混合菌修复石油污染土壤

选取4种从石油污染土壤中分离出的石油降解菌(包括根瘤菌(A)、节细菌(B)、嗜盐菌(C)和芽孢杆菌(D)),对模拟石油污染土壤进行了微生物修复实验。考察了4种菌单独使用时的石油降解率,确定了混合菌的最佳配比和菌群的最优培养条件,并对比了微生物修复前后土壤的各项性质。实验结果表明:4种菌均可提高微生物修复石油污染土壤的修复效果,使用D菌时石油降解率最高;当混合菌的w(A)∶w(B)∶w(C)∶w(D)=12∶2∶21∶65时,在培养条件为混合菌接种量122.0 mL/kg、土壤含水率14%(w)、鸡粪加入量90 g/kg、麦糠加入量150 g/kg和表面活性剂加入量22 mL/kg的情况下,土壤的修复效果最好,40 d后石油降解率达66.95%;经混合菌修复的石油污染土壤,其肥力明显升高,脱氢酶、过氧化酶和脲酶的活性均升高,微生物数量也有明显增加。     

表面活性剂在多环芳烃污染土壤修复中的应用

介绍了单一表面活性剂（非离子表面活性剂、生物表面活性剂）、阴-非离子混合表面活性剂对多环芳烃的增溶作用、增溶机理及无机离子对表面活性剂增溶能力的影响,综述了化学表面活性剂和生物表面活性剂在污染土壤生物修复中的应用。由于生物表面活性剂具有许多独特的优点,今后应加强生物表面活性剂的开发与应用研究。     

表面活性剂对土壤中石油污染物的解吸

采用4种表面活性剂解吸老化石油污染土壤中的污染物,对其解吸动力学特征及残油组分进行了分析。实验结果表明:在表面活性剂质量浓度相同(0.5 g/L)条件下,土壤中石油污染物解吸率的大小顺序为十二烷基硫酸钠(SDS)曲拉通X-100(TX-100)吐温-80(TW-80)十二烷基苯磺酸钠(SDBS);SDS的解吸率最高,经48 h累积解吸后土壤中石油污染物的解吸率为38.7%;表面活性剂对石油污染物的解吸动力学曲线用Elovich方程拟合,效果最好,相关系数为0.970 2~0.995 6;非离子表面活性剂(TX-100、TW-80)对石油污染物中饱和烃组分的解吸率优于阴离子表面活性剂(SDS、SDBS),而对芳香烃组分的解吸率不如阴离子表面活性剂。     

混合菌修复石油污染土壤

选取4种从石油污染土壤中分离出的石油降解菌（包括根瘤菌（A）、节细菌（B）、嗜盐菌（C）和芽孢杆菌（D））,对模拟石油污染土壤进行了微生物修复实验。考察了4种菌单独使用时的石油降解率,确定了混合菌的最佳配比和菌群的最优培养条件,并对比了微生物修复前后土壤的各项性质。实验结果表明：4种菌均可提高微生物修复石油污染土壤的修复效果,使用D菌时石油降解率最高;当混合菌的w（A）∶w（B）∶w（C）∶w（D）=12∶2∶21∶65时,在培养条件为混合菌接种量122.0 mL/kg、土壤含水率14%（w）、鸡粪加入量90 g/kg、麦糠加入量150 g/kg和表面活性剂加入量22 mL/kg的情况下,土壤的修复效果最好,40 d后石油降解率达66.95%;经混合菌修复的石油污染土壤,其肥力明显升高,脱氢酶、过氧化酶和脲酶的活性均升高,微生物数量也有明显增加。     

植物修复石油污染土壤的研究进展

石油污染土壤的植物修复技术以其处理成本低、无二次污染、自然美观等特点,正逐步成为未来石油污染治理研究的一个重要方向。文章综述了植物修复石油污染土壤的研究进展,阐述了植物修复的机理、影响因素、转基因植物的应用及与其他技术的联用,并探讨了植物修复石油污染土壤研究中存在的问题。     

营养物质协同真菌修复石油烃污染土壤

研究了生物强化结合生物刺激对石油烃污染土壤的修复效果及对修复后土壤pH、土壤呼吸作用的影响。结果表明：向石油烃污染土壤中添加菌液量为20%(w,下同)的真菌杂色曲霉(Aspergillus versicolor)、10%的蔗糖,修复30 d时总石油烃(TPH)降解率达55.63%;添加7%的酒石酸修复30 d时,TPH降解率为42.9%。添加蔗糖和酒石酸修复后,土壤pH均呈下降趋势,土壤CO₂释放量均增大。石油烃污染土壤颗粒紧致密实,土壤颗粒之间孔隙被堵塞;经生物修复后土壤孔隙结构明显增大,表面粗糙、疏松,呼吸作用增强。     

石油污染土壤修复技术的进展

综述了石油污染土壤修复技术的发展现状及存在的瓶颈,分析了石油污染对油-水-土界面性质、土-水关系和土壤渗透性等水理性质的影响.对石油污染土壤再利用于工程建设进行了探讨,并总结了石油污染土壤主要的力学性质变化,为石油污染土壤修复技术的工程实践和机理研究提供参考.     

曝气强化非离子表面活性剂洗涤法修复柴油污染土壤

采用异位修复法,利用非离子表面活性剂洗涤柴油污染土壤,并在洗涤过程中曝气强化。考察了洗涤效果的影响因素,并通过表面张力和接触角的测定探讨了洗涤机理。实验结果表明:曝气对污染土壤中柴油的洗脱有强化作用,可提高洗脱率10%~20%;3种非离子表面活性剂的洗脱效果优劣次序为聚氧乙烯月桂醚(Brij-35)曲拉通X-100(TX-100)吐温-80(Tw-80);在表面活性剂浓度为1倍临界胶束浓度、曝气量为7.5 L/min、洗涤时间为60 min、洗涤液pH为11.0的优化条件下,Brij-35对柴油的洗脱率达77.4%,污染土样的含油率从7.0%降至1.6%,接触角从24.12°降至6.65°,可基本恢复土壤的亲水性;洗涤液的表面张力随表面活性剂浓度的增加而降低,但不受洗涤液pH的影响。     

生物表面活性剂强化疏水性有机污染物生物降解研究进展

介绍了生物表面活性剂的类型、理化性质、生物表面活性剂提高疏水性有机污染物生物可利用性的机理及其在污染场地生物修复中应用方面的研究进展。生物表面活性剂不仅具有乳化、增溶、降低表／界面张力等功能,而且低毒、对环境友好、易于生物降解,因而在环境污染的生物治理方面具有极大的应用潜力。     

铁活化过硫酸盐修复石油烃污染土壤的研究进展

分析了Fe~0、Fe~(2+)和Fe~(3+)活化过硫酸盐氧化石油烃的机理,介绍了土壤中石油烃污染物降解的影响因素以及总结了铁活化过硫酸盐修复石油烃污染土壤技术的不足。指出应以铁活化过硫酸盐原位修复作为土壤中高浓度有机污染物的前处置方法,再结合微生物或植物修复等技术,以减少对土壤理化性质的影响;另外,检测仪器的发展有利于土壤修复技术的应用。     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Effect of depth of landfill on the characteristics of soil-like material of aged waste: a case study of Bhalswa dumpsite,India

Journal of Material Cycles and Waste Management - This study characterizes the municipal solid waste (MSW) accumulated for more than 25 years at Bhalswa dumpsite, Delhi, India. 50...     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％;靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.