Study of Thermo-Mechanical and Morphological Behaviour of Biodegradable PLA/PBAT/Layered Silicate Blend Nanocomposites

Poly (lactic acid) (PLA) and poly (butylene adipate-co-terephthalate) (PBAT) blend nanocomposites were prepared using melt blending technique followed by compression moulding. The blend nanocomposites were prepared with a variation of PBAT loading along with maleic anhydride and benzoyl peroxide ranging from 5 to 20 wt% along with two different commercially available nanoclays cloisite 93A and cloisite 30B (C30B) at 3 wt% loading. The maleic anhydride and benzoyl peroxide were used during the melt blending of the blend nanocomposites as a compatibilizer and as an accelerator respectively. Maleic anhydride used to enhance the compatibility of the PLA/PBAT blend and as well as the uniform adhesion of the nanoclays with them. The properties and characterizations of PLA matrix and the PLA/PBAT blend nanocomposites have been studied. The tensile strength, % elongation and impact strength increased with the preparation of PLA/PBAT blend nanocomposites as compared with PLA matrix. PLA/PBAT/C30B blend nanocomposites exhibited optimum tensile strength at 15 wt% of PBAT loading. Differential scanning calorimetry and thermogravimetric analysis also showed improved thermal properties as compared with virgin PLA. The wide angle X-ray diffraction studies indicated an increase in d-spacing in PLA/PBAT/C30B blend nanocomposite thus revealing intercalated morphology.     

The Effect of Acetylation on the Hydrolytic Degradation of PLA/Clay Nanocomposites

In this study, the hydrolytic degradation of Poly(lactic acid) (PLA) and acetylated PLA (PLA-Ac)–clay nanocomposites were investigated. The organo clay was obtained by ion exchange reaction using cetyl tri methyl ammonium bromide (CTAB). Nanocomposites containing 2, 5 and 8% mass ratio of organo clay (CTAB-O) were prepared. PLA and its organo clay nanocomposites were characterized by scanning electron microscope (SEM), thermo gravimetric analysis (TGA) and X-ray diffraction (XRD) to determine the morphology before and after hydrolytic degradation. Fourier transform infrared (FTIR) analyses of PLA and PLA-Ac were also obtained. The hydrolytic degradation of polymers and their composites were investigated in the phosphate buffered saline solution (PBS). The results showed that controlled hydrolytic degradation was observed in the samples with end group modification of PLA. While weight loss of PLA films was 28%, that of PLA-Ac films was 18% after 60 days degradation time. The weight loss was obtained as 29.5 and 25.5% for PLA-5 wt% organo clay (PLA/5CTAB-O) and PLA-Ac-5 wt% organo clay (PLA-Ac/5CTAB-O) nanocomposites films, respectively. It was also observed that thermal degradation of PLA-Ac was much more than that of PLA. Hydrolytic degradation increased depending on organo clay content. The end group modificated PLA results in controlled hydrolytic degradation. While hydrolytic degradation in polymer films occurred as surface erosion, bulk erosion was observed in composite films.     

Fabrication and Characterization of Polyaniline Based Nano-Composite with Their Physico-Chemical and Environmental Applications

A series of organic–inorganic conducting nano polymer-matrix composite cation-exchanger have been synthesized via sol–gel method and characterized through FTIR, XRD, TGA-DTA, SEM, and TEM studies. The structural studies confirm the semi-crystalline nature of the material but the morphology of the exchanger gets changed after incorporation of inorganic moiety. The particle size of the nano-composite was found to be 19.2 nm. The observed band gap for the different samples was found to be in the range of 3.70–4.61 eV which shows that nano-composite material covers semiconducting range but the resistivity of samples is highly dependent on the percentage of inorganic part in the composite. Further the oxidative degradation of the polymer backbone begins after the removal of trapped water successively followed by dopant and low molecular weight oligomers. During the antimicrobial screening, the nano-composite was found to be active against different strains of bacteria and fungi. Gel electrophoresis and molecular docking studies were carried out to check the interaction and mechanism of inhibition of microbial growth, respectively by studying the effect of the nano-composite with DNA-Topoisomerase-1.     

PLA and Montmorilonite Nanocomposites: Properties, Biodegradation and Potential Toxicity

The concern related to solid waste increases efforts to develop products based on biodegradable materials. At present, PLA has one of the highest potentials among biopolyesters, particularly for packaging. However, its application is limited in some fields. In order to optimize PLA properties, organo-modified montmorilonites have been extensively used to obtain nanocomposites. Although PLA nanocomposites studies are widely reported in the literature, there is still few information about the influence of organoclays on de biodegradation process, which is a relevant information, since one of the main purposals related to the final disposal of biopolymers as PLA is composting. Besides, in the last years some research has been conducted in order to evaluate the potential toxicity of montmorilonite, unmodified or organo-modified. Since the use of montmorilonite is expanding in different applications, human exposure and risk assessment are important issues to be investigated. In this context, this review intends to compile available information related to common organoclays used for PLA nanocomposites, its properties, biodegradation analysis and potential toxicity evaluation of nanocomposites, focused on montmorilonite as filler. Two issues of relevance were pointed out. The first is food safety and quality, and the second consideration is the environmental effect.     

Characterization of EVA/PLA Blends When Exposed to Different Environments

EVA/PLA blends compatibilized with EVA-g-PLA grafted copolymers synthesized by reactive extrusion, through transesterification reaction between ethylene-vinyl-acetate (EVA) and polylactide (PLA) using titanium propoxide (Ti(OPr)₄) as catalyst, were characterized when exposed to different environments. Stability to UV radiation was assessed exposing the samples to a Xenon lamp, which simulates the sun UV spectrum and the biodegradability was evaluated by biochemical oxygen demand (BOD) in a closed respirometer. Exposed samples were removed periodically and analyzed by several analytical techniques, such as, FTIR, DSC, rheology and tensile tests. The results obtained evidenced that UV radiation induces structural modifications, which affect substantially rheological and mechanical properties. Moreover, the blend with higher amount of copolymer exhibits lower photo durability and greater biodegradability. From the environmental point of view, these new materials are very promising for application with short lifetime, like packaging.     

Fabrication and Properties of Acid Treated Carbon Nanotubes Reinforced Soy Protein Nanocomposites

Acid treated multiwalled carbon nanotubes (MWNTs) were incorporated into glycerol plasticized soy protein to form MWNTs/soy protein nanocomposite plastics. The influence of the polar groups grafted on carbon nanotubes by acid treatment on the compatibility would be studied. The results showed that aggregation of carbon nanotubes was reduced by acid treatment and some polar groups were grafted on the nanotubes. The modified MWNTs were dispersed in soy protein matrix homogeneously and exhibited good compatibility with soy protein matrix. The crystalline structure of soy protein was not changed by MWNTs. The mechanical properties were dramatically enhanced through MWNTs incorporation due to the strong hydrogen bonding between them and the homogeneously dispersion of MWNTs in protein matrix, indicating the reinforcing effect of MWNTs in soy protein matrix. The water uptake was reduced and the thermal stability was enhanced by MWNTs incorporation.     

Novel LLDPE/Cellulose Microfiber/Nanoclay Nanocomposites Based on In Situ Nanoclay Fabrication Simultaneously with Wastewater Treatment

Journal of Polymers and the Environment - This article presents a unique approach for paper wastewater treatment simultaneously with in-situ intercalating clay and using the cellulose fiber/in situ...     

Water transport in polylactic acid (PLA), PLA/ polycaprolactone copolymers, and PLA/polyethylene glycol blends

Polylactic acid (PLA) is a hydrolytically degradable aliphatic polyester, and water vapor permeability may have a significant influence on the rate of degradation. A method is devised to use bags prepared from PLA films and filled with molecular sieves to determine the water vapor permeability in the polymer, its copolymers with caprolactone, and blends with polyethylene glycol. The “solution-diffusion” model is used to determine the permeability parameters. These include the solubility coefficient,S, a measure of the equilibrium water concentration available for hydrolysis and the diffusion coefficient,D, which characterizes the rate of water vapor diffusion into the film under specific conditions. Values ofS andD at 50‡C and 90% relative humidity ranged from 400 × 10^-6 to 1000 × 10^-6 cm³ (STP)/(cm³ Pa) and 0.20 × 10^-6 to 1.0 × 10^-6 cm²/s, respectively. TheS andD coefficients were also measured at 20 and 40‡C and compared to those of other polymers. The degree of crystallinity was found to have little influence on the measured permeability parameters. The heat of sorption, δH_S, and the activation energy of diffusion, E_D, were used to show that the permeability process is best described by the “water cluster” model for hydrophobic polymers. Finally, the diffusion coefficient is used to compare the rate of water diffusion to the rate of water consumption by ester hydrolysis. Results indicate that hydrolytic degradation of PLA is reaction-controlled.     

Biodegradable Composite Foams of PLA and PHBV Using Subcritical CO<Subscript>2</Subscript>

One key strategy for increasing the application potential for biodegradable plastics lies in improving the physical and mechanical characteristics, which can be attained by inducing a cellular morphology in the pure polymer with the aid of a blowing agent, as well as by blending two or more polymers with the desirable properties. This paper examines the effect that blending two biodegradable polymers has on the thermal properties and morphology of the resultant foams blown with carbon dioxide (CO₂). Polylactic acid (PLA), polyhydroxybutyrate-co-valerate (PHBV) and blends of both were foamed and characterized in terms of thermal characteristics, relative density, cell size, and foam morphology. The results indicate that although PLA and PHBV are immiscible, the presence of small quantities of PHBV (25 wt%) could lead to low density foams with finer, more uniform cells. Furthermore, the crystallinity of PHBV was found to be unaffected by the presence of PLA in the composite, which supports the immiscibility of PLA and PHBV.     

Biodegradability of Poly (lactic acid), Preparation and Characterization of PLA/Gum Arabic Blends

In this study, the biodegradation of PLA films using microorganisms from Lake Bogoria (Kenya) were investigated. The biodegradation tests done using certain strains of thermophilic bacteria showed faster biodegradation rates and demonstrated temperature dependency. The biodegradation of the PLA films was studied using Gel Permeation Chromatography (GPC) and light microscopy. The biodegradation of PLA was demonstrated by decrease in molecular weight. The preparation and characterization of PLA/Gum Arabic blends were also investigated using DSC, TGA, TMA and NMR. In summary, the results obtained in this research show that PLA films undergo fast biodegradation using thermophiles isolated from Lake Bogoria. The PLA/GA blends studies show it is possible to prepare films of varying hydrophobic–hydrophilic properties for various applications.     

PLA and Organoclays Nanocomposites: Degradation Process and Evaluation of ecotoxicity Using Allium cepa as Test Organism

In this study, nanocomposites of PLA and organoclays Cloisite 20A and Cloisite 30B were prepared by the melt intercalation method and the obtained samples were characterized by transmission electron microscopy (TEM). Since composting is an important proposal to the final disposal of biopolymers, the influence of clays on the hydrolytic degradation process of PLA was evaluated by visual analysis and monitoring of molecular weight after periods of 15 and 30 days of degradation in compost. After degradation of the materials in composting environment, the evaluation of cytotoxic, genotoxic and mutagenic effects of compost aqueous extract was carried out using a bioassay with Allium cepa as test organism. The TEM micrographs permitted the observation of different levels of dispersion, including exfoliated regions. In the evaluation of hydrolytic degradation it was noted that the presence of organoclays can decrease the rate of degradation possibly due to the barrier effect of clay layers and/or the higher degree of crystallinity in the nanocomposite samples. Nevertheless, even in the case of nanocomposites, the molecular weight reduction was significant, indicating that the composting process is favorable to the chain scission of PLA in studied materials. In the analysis performed by the bioassay using A. cepa as test organism, it was found that after degradation of the PLA and its nanocomposites the aqueous extract of compost samples induced a decreasing in the mitotic index and an increasing in the induction of chromosomal abnormalities. These results were statistically significant in relation to the negative control (distilled water). By comparing the results obtained for the nanocomposites in relative to pure polymer, there were no statistically significant differences. The types of the observed chromosomal aberrations indicated a possible genotoxic effect of the materials, which may be related to an aneugenic action of PLA degradation products.     

Synthesis and Characterization of Polyols and Polyurethane Foams from PET Waste and Crude Glycerol

In this study, polyethylene terephthalate (PET) waste from post-consumer soft-drink bottles and crude glycerol from the biodiesel industry were used for the preparation of polyols and polyurethane foams. PET waste was firstly depolymerized by the glycolysis of diethylene glycol. The glycolyzed PET oligomers were then reacted with crude glycerol at different weight ratios to produce polyols via a series of reactions, such as esterification, transesterification, condensation, and polycondensation. The polyols were characterized by titration, viscometry, gel permeation chromatography (GPC), and differential scanning calorimetry. Subsequently, polyurethane (PU) foams were made via the reaction between the produced polyols and polymeric methylene-4,4′-diphenyl diisocyanate and were characterized by mechanical testing, scanning electron microscopy, and thermogravimetric analysis. Polyols from crude glycerol and their PU foams were also prepared to compare properties with those of polyols and PU foams from PET and crude glycerol. The influence of aromatic segments existing in glycolyzed PET and glycerol content on the properties of the polyols and PU foams was investigated. It was found that aromatic segments of polyols from glycolyzed PET helped increase their molecular weights and improve thermal stability of PU foams, while high glycerol content in polyols increased the hydroxyl number of polyols and the density and compressive strength of PU foams.     

Synthesis,Characterization and Application of Biodegradable Crosslinked Carboxymethyl Chitosan/Poly(Ethylene Glycol) Clay Nanocomposites

Crosslinked carboxymethyl chitosan (CMCh)/poly(ethylene glycol) (PEG) nanocomposites were synthesized using terephthaloyl diisothiocyanate as a crosslinking agent, in presence of montmorillonite (MMT), in different weight ratios of the two matrices. Characterization of nanocomposites was performed using different analyses. Swelling behavior was studied in different buffered solutions. It was found that formation of crosslinked CMCh/PEG nanocomposites increased the swell ability. Metal ions adsorption had also been investigated. The results indicated that crosslinked CMCh adsorbs various metal ions much more than non-crosslinked CMCh. Antimicrobial activity was examined against Gram-positive bacteria (S. aureus (RCMB 010027) and S. Pyogens (RCMB 010015), Gram-negative bacteria (E. coli (RCMB 010056), and also against fungi (A. fumigates (RCMBA 02564, G. candidum (RCMB 05096) and C. albicans (RCMB 05035). Data indicated that most of these nanocomposites exhibited good antimicrobial potency. Degradation studies were carried out in simulated body fluid for different time periods in order to find out the degradation index. Results showed that weight loss (%) of most of the nanocomposites increased as a function of incubation time.     

Preparation and Characterization of Clay Nanocomposites of Plasticized Starch and Polypropylene Polymer Blends

Plasticized starch (PLS) is a renewable, degradable, and inexpensive polymer, but it suffers from poor mechanical properties. The mechanical properties can be improved by blending PLS with polyolefins, nonetheless, at high PLS content, the mechanical properties remain poor. Here we show that addition of clay can greatly improve the mechanical properties of PLS/polypropylene blends at high starch content. Unmodified and organically modified montmorillonite clays, MMT and Cloisite 30B respectively, were added to blends of glycerol-plasticized starch and polypropylene, compatibilized using maleated polypropylene. TEM indicates that MMT is well dispersed in the PLS phase of the blends, while Cloisite 30B is located both within the PLS phase as well as at the interface between PLS and PP. At high PLS content, the addition of clay increased the tensile strength and tensile modulus by an order of magnitude, while reducing the ultimate elongation only slightly. Such improvements are attributable to both the addition of clay as a reinforcing component, as well as to the change in the two phase morphology due to addition of clay.     

Biodegradable Blends with Potential Use in Packaging: A Comparison of PLA/Chitosan and PLA/Cellulose Acetate Films

Poly(lactic acid) (PLA) is a biodegradable polymer that exhibits high elastic modulus, high mechanical strength, and feasible processability. However, high cost and fragility hinder the application of PLA in food packaging. Therefore, this study aimed to develop flexible PLA/acetate and PLA/chitosan films with improved thermal and mechanical properties without the addition of a plasticizer and additive to yield extruder compositions with melt temperatures above those of acetate and chitosan. PLA blends with 10, 20, and 30 wt% of chitosan or cellulose acetate were processed in a twin-screw extruder, and grain pellets were then pressed to form films. PLA/acetate films showed an increase of 30 °C in initial degradation temperature and an increase of 3.9 % in elongation at break. On the other hand, PLA/chitosan films showed improvements in mechanical properties as an increase of 4.7 % in elongation at break. PLA/chitosan film which presented the greatest increase in elongation at break proved to be the best candidate for application in packaging.     

Preparation and Characterization of Polyaniline and Ag/ Polyaniline Composite Nanoporous Particles and Their Antimicrobial Activities

Polyaniline (PANI) and Ag/PANI nanoporous composite were prepared by an oxidative polymerization method. The oxidation process of PANI nanoparticles was occurred using (NH₄)₂S₂O₈ while the oxidation process of Ag/PANI nanoporous composite was occurred using AgNO₃ under the effect of artificial radiation. The structural, morphological, and optical properties of the PANI and Ag/PANI nanoporous structures were studied using different characterization tools. The results confirm the formation of polycrystalline nanoporous PANI and spherical nanoporous composite of Ag/PANI particles. Antibacterial activity tests against gram-positive bacteria, Bacillus subtilis and Staphylococcus aureus, and gram-negative bacteria, Escherichia coli, and Salmonella species were carried out using different concentrations of PANI nanoparticles and Ag/PANI nanoporous composites. PANI has not antibacterial effect against all studied pathogens. In contrast, Ag/PANI nanoporous composites possessed antibacterial activity that is identified by the zone of inhibition. The inhibition zones of bacteria are in order; Salmonella species?>?S. aureus?>?B. subtilis?>?E. coli. The inhibition zones of all bacteria increased with increasing concentrations of Ag/PANI nanoporous composites from 200 to 400 ppm then decreased with further increasing of the dose concentrations to 600 ppm. Finally, a simplified mechanism based on the electrostatic attraction is presented to describe the antimicrobial activity of Ag/PANI nanoporous composite.     

Preparation and Characterization of Xylan Derivatives and Their Blends

Although hemicellulose is found widely in nature, it is currently under-utilized as a raw material for commercial applications. It would be desirable to find new uses for hemicellulose in order to add value to this agro-based material. A common type of hemicellulose is xylan, which is found in a number of wood species and in cotton. In this work we prepared cationic and anionic xylan derivatives and characterized them by ¹³C NMR, FT-IR, size exclusion chromatography (SEC), thermal analysis, and rheology. In particular, the ¹³C NMR spectra of carboxymethyl xylan (CMX) and quaternary ammonium-adducted xylan (QAX) were fully assigned with the help of samples with different degrees of substitution. SEC indicated that the beechwood xylan showed a bimodal molecular weight distribution, but with derivatization the distribution tended to become unimodal. Thermal analysis and rheology studies did not uncover any surprises; the solution of xylan and its derivatives exhibited mostly Newtonian behavior. The blends of CMX and QAX produced a precipitate at almost all ratios, indicating the formation of a polyelectrolyte complex. When cationic and anionic xylan samples were added together to paper, the paper dry strength increased. Thus, the combination of cationic/anionic xylan may be of interest in selected applications.     

Preparation and Properties of Biodegradable Foams

Foam extrusion of biodegradable polyester [poly(butylene adipate-co-terephthalate) (PBAT)] and its blends with maleated thermoplastic starch (MTPS) using a chemical blowing agent was performed. The effect of MTPS and percentage of chemical blowing agent on various foam properties is discussed. In general, an increased amount of PBAT in the foams improves the properties of the foams. The foam samples were characterized by measurements of density, expansion ratio, specific length, compressive strength, resiliency, moisture sorption, and imaging using digital light microscopy. Density, expansion ratio, and specific length measurements show that the best characteristics of lowest density, highest expansion ratio, and highest specific length are exhibited by the PBAT samples. The compressive strength and foam density exhibit a power-law relationship. Greater amounts of PBAT in the samples increase the resiliency and decrease the steady state weight gain during moisture sorption. All samples show regions of unfoamed material when only 3% chemical blowing agent is used, but when 5 and 7% chemical blowing agent is used, the samples exhibit cells throughout the matrix.     

Mechanical and Thermal Properties of PLLA/PCL Modified Clay Nanocomposites

Poly(l-lactic acid) (PLLA)/poly(caprolactone) (PCL) and two types of organoclay (OMMT) including a fatty amide and ocatdecylamine montmorillonite (FA-MMT and ODA-MMT) were employed to produce polymer nanocomposites by melt blending. Materials were characterized using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), elemental analysis, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Mechanical properties were also investigated for these nanocomposites. The nanocomposites showed increasing mechanical properties and thermal stability. XRD results indicated that the materials formed nanocomposites. SEM morphology showed that increasing content of OMMT reduced the domain size of phase separated particles. TEM outcomes have confirmed the intercalated type of nanocomposite. Additionally, a solution casting process has been used to prepare these nanocomposites and characterized to compare these results with the above process.     

Influence of TiO<Subscript>2</Subscript> Nanoparticles on the Crystallization Behaviour and Tensile Properties of Biodegradable PLA and PCL Nanocomposites

This paper investigated the influence of TiO₂ nanoparticles on the morphologies, as well as crystallization behaviour and kinetics, of neat PLA and PCL, and of these polymers in different PLA/PCL blends. We used transmission electron microscopy to evaluate the morphologies of the systems, while the crystallization behaviour and kinetics were investigated through differential scanning calorimetry (DSC). In addition to standard and modulated (StepScan) DSC analyses, the self-nucleation temperatures of neat PCL and PCL in the different nanocomposites were determined, followed by a self-nucleation and annealing thermal fractionation analysis of PCL crystallization and an Avrami isothermal kinetic analysis of PCL crystallization and PLA cold crystallization. We found that the nanoparticles were well dispersed, but only in the PLA phase of the blends, with only a few on the interface or in the PCL phase. They did nucleate and accelerate, and influence the mechanism of, the PCL crystallization in neat PCL, but had little influence on PCL crystallization in the blends. They strongly influenced the rate of cold crystallization of PLA, but had little influence on this parameter in the blends. The tensile properties were also determined, and changes in these properties could be related to the morphologies of the systems.