New biofidelic corridor and biofidelity test procedure for pedestrian legform impactors

The objectives of this research are to propose a new impact response corridor for the ISO legform impactor and to determine the biofidelity of the current legform impactor with rigid leg and thigh developed by the Transport Research Laboratory (TRL). The latest data obtained from Post Mortem Human Subject (PMHS) knee impact tests were analyzed in connection with the proposal, and biofidelity legform impact tests were conducted using the current rigid legform impactor. New normalized biofidelic corridors of impact force corresponding to adult male 50th percentile (AM50) are proposed. The impact test results indicate the current rigid legform impactor does not have sufficient human knee biofidelity. The present results suggest that human tolerance can not be used directly for the injury reference value of the legform impactor. A conversion method is needed to interpret the data measured by current legform impactors as the injury reference value.     

Investigation on the effect of impact location height on pedestrian safety using a legform impactor dynamic model

Because of rapid increase in the urban population and hence road traffic, the vehicle–pedestrian crashes are more frequent and have become a major concern in road traffic safety. Though the bumper of a vehicle plays an important role to protect the vehicle body damage in low speed impacts, many bumpers particularly in larger vehicles are too stiff for pedestrian protection and safety. To prevent lower extremity injuries in car–pedestrian collisions, it is important to determine the loadings that car front structures impart on the lower extremities and the mechanisms by which injuries are caused. In the present work, a dynamic legform impactor model is introduced and validated against EEVC/WG17 criteria. The collision mechanism between a GMT bumper and the legform impactor model is investigated numerically using LS-DYNA software. The effect of the height of the impact point of bumper assembly to lower extremity injuries is also investigated. In this paper, it is shown that changing the local stiffness of bumper assembly due to the change in the height of the bumper and distribution of stiffness from upper parts of the bumper assembly to lower parts are the most important parameters in the pedestrian’s leg injuries. As lower extremity injuries are related to the lower bumper height, developing special legform impactors for different countries with different average person height seems essential in investigating the effect of people’s height on lower extremity injuries.     

Finite Element Analysis of Knee Injury Risks in Car-to-Pedestrian Impacts

In vehicle–pedestrian collisions, lower extremities of pedestrians are frequently injured by vehicle front structures. In this study, a finite element (FE) model of THUMS (total human model for safety) was modified in order to assess injuries to a pedestrian lower extremity. Dynamic impact responses of the knee joint of the FE model were validated on the basis of data from the literature. Since in real-world accidents, the vehicle bumper can impact the lower extremities in various situations, the relations between lower extremity injury risk and impact conditions, such as between impact location, angle, and impactor stiffness, were analyzed. The FE simulation demonstrated that the motion of the lower extremity may be classified into a contact effect of the impactor and an inertia effect from a thigh or leg. In the contact phase, the stress of the bone is high in the area contacted by the impactor, which can cause fracture. Thus, in this phase the impactor stiffness affects the fracture risk of bone. In the inertia phase, the behavior of the lower extremity depends on the impact locations and angles, and the knee ligament forces become high according to the lower extremity behavior. The force of the collateral ligament is high compared with other knee ligaments, due to knee valgus motions in vehicle-pedestrian collisions.     

Finite element analysis of knee injury risks in car-to-pedestrian impacts

In vehicle-pedestrian collisions, lower extremities of pedestrians are frequently injured by vehicle front structures. In this study, a finite element (FE) model of THUMS (total human model for safety) was modified in order to assess injuries to a pedestrian lower extremity. Dynamic impact responses of the knee joint of the FE model were validated on the basis of data from the literature. Since in real-world accidents, the vehicle bumper can impact the lower extremities in various situations, the relations between lower extremity injury risk and impact conditions, such as between impact location, angle, and impactor stiffness, were analyzed. The FE simulation demonstrated that the motion of the lower extremity may be classified into a contact effect of the impactor and an inertia effect from a thigh or leg. In the contact phase, the stress of the bone is high in the area contacted by the impactor, which can cause fracture. Thus, in this phase the impactor stiffness affects the fracture risk of bone. In the inertia phase, the behavior of the lower extremity depends on the impact locations and angles, and the knee ligament forces become high according to the lower extremity behavior. The force of the collateral ligament is high compared with other knee ligaments, due to knee valgus motions in vehicle-pedestrian collisions.     

我国(讨论稿)和欧洲关于行人保护法规的异同点

通过对欧洲和我国讨论稿关于行人保护法规的分析比较研究,在定义方面有着相同和不同;在下腿型冲击器对保险杠的试验、上腿型冲击器对保险杠的试验、儿童头型冲击器对发动机罩的试验、成人头型冲击器对发动机罩的试验等实验中,使用的实验仪器设备、实验手段和方法、实验程序、评价指标存在着相同和不同之处。与欧洲法规相比,我国讨论稿的一些评价指标值有待进一步完善,试验手段和方法需要进一步改进,通过比较分析来不断修订我国行人保护法规讨论稿,以利于我国未来正式颁布行人保护法规。     

Analysis of the influence of passenger vehicles front-end design on pedestrian lower extremity injuries by means of the LLMS model

Objective: This work aims at investigating the influence of some front-end design parameters of a passenger vehicle on the behavior and damage occurring in the human lower limbs when impacted in an accident.

Methods: The analysis is carried out by means of finite element analysis using a generic car model for the vehicle and the lower limbs model for safety (LLMS) for the purpose of pedestrian safety. Considering the pedestrian standardized impact procedure (as in the 2003/12/EC Directive), a parametric analysis, through a design of experiments plan, was performed. Various material properties, bumper thickness, position of the higher and lower bumper beams, and position of pedestrian, were made variable in order to identify how they influence the injury occurrence. The injury prediction was evaluated from the knee lateral flexion, ligament elongation, and state of stress in the bone structure.

Results: The results highlighted that the offset between the higher and lower bumper beams is the most influential parameter affecting the knee ligament response. The influence is smaller or absent considering the other responses and the other considered parameters. The stiffness characteristics of the bumper are, instead, more notable on the tibia. Even if an optimal value of the variables could not be identified trends were detected, with the potential of indicating strategies for improvement.

Conclusions: The behavior of a vehicle front end in the impact against a pedestrian can be improved optimizing its design. The work indicates potential strategies for improvement. In this work, each parameter was changed independently one at a time; in future works, the interaction between the design parameters could be also investigated. Moreover, a similar parametric analysis can be carried out using a standard mechanical legform model in order to understand potential diversities or correlations between standard tools and human models.     

Assessing the performance of motorcyclists’ impact protectors in simulated ATD knee and shoulder impacts

Objective: Fractures are a common injury among motorcycle riders and can have serious health implications. Impact protection (IP) has been designed to help prevent fractures, yet there are conflicting opinions as to whether this IP does in fact help prevent fractures in real-world crashes. This work aimed to (1) use simulated dummy impacts to examine whether existing types of IP could reduce the force transferred to the underlying bone to below fracture tolerance levels and (2) investigate whether current European Standard (EN 1621-1) test procedures for impact protectors designed for motorcyclists are sufficient to ensure fracture protection.

Method: Twenty-three shoulder and 7 knee IP specimens were tested using a 23-kg impactor contacting axially along the clavicle and femur of an anthropomorphic test device (ATD) at an energy level corresponding to the fracture tolerance of these bones. Sixteen IP specimens were the same as those worn by motorcycle riders involved in crashes where injury outcome was known (knee: n?=?3; shoulder: n?=?13) and the IP had been previously tested to EN 1621-1. Other IP tested represented a wide range of IP available for purchase at a motorcycle accessory store. Double and triple layers of IP were also tested. Energy attenuated during the dummy impacts was compared to energy attenuated when tested to EN 1621-1.

Results: Of the 23 shoulder IP tested, the average percentage reduction of transferred force to the shoulder from the baseline test was 7.6?±?4.8%. The percentage reduction of transferred force to the knee from the baseline was 43.9?±?7.5%. The entire group of knee IP tested reduced the transferred force to the knee to below the 10-kN injury threshold for the femur. There was a positive but nonsignificant correlation between the ATD test and the EN 1621-1 impact test performance, suggesting that the European standard test method likely provides a good indication of IP performance. However, given the low correlation coefficient, the relationship between IP performance in the European standard test method and injury protection remains unclear.

Conclusion: Though the energy attenuation test method in the European standard may be an appropriate approach, distinct differences in injury protection performance observed between knee and shoulder IP indicate that there may be a need for different performance criteria for IP designated to protect different body regions.     

人车碰撞中行人大腿保护研究

研究提高人车碰撞中行人大腿的保护性能的方法。首先对大腿伤害机理,伤害评价指标以及车辆自身结构进行阐述和研究,总结车辆前端结构的关键参数;对某车型的前大灯进行结构改进,按照欧洲新车安全评鉴协会(Euro NCAP)行人大腿保护的试验评价方法,改进后进行碰撞试验;建立装有发动机罩安全气囊的整车仿真模型,验证安全气囊对行人大腿的保护性能。经过试验和仿真可以得出:车辆前大灯结构刚度改进和发动机罩安全气囊可以改善行人大腿的保护性能。     

Can new passenger cars reduce pedestrian lower extremity injury? A review of geometrical changes of front-end design before and after regulatory efforts

Objective: Pedestrian lower extremity represents the most frequently injured body region in car-to-pedestrian accidents. The European Directive concerning pedestrian safety was established in 2003 for evaluating pedestrian protection performance of car models. However, design changes have not been quantified since then. The goal of this study was to investigate front-end profiles of representative passenger car models and the potential influence on pedestrian lower extremity injury risk.

Methods: The front-end styling of sedans and sport utility vehicles (SUV) released from 2008 to 2011 was characterized by the geometrical parameters related to pedestrian safety and compared to representative car models before 2003. The influence of geometrical design change on the resultant risk of injury to pedestrian lower extremity—that is, knee ligament rupture and long bone fracture—was estimated by a previously developed assessment tool assuming identical structural stiffness. Based on response surface generated from simulation results of a human body model (HBM), the tool provided kinematic and kinetic responses of pedestrian lower extremity resulted from a given car's front-end design.

Results: Newer passenger cars exhibited a “flatter” front-end design. The median value of the sedan models provided 87.5 mm less bottom depth, and the SUV models exhibited 94.7 mm less bottom depth. In the lateral impact configuration similar to that in the regulatory test methods, these geometrical changes tend to reduce the injury risk of human knee ligament rupture by 36.6 and 39.6% based on computational approximation. The geometrical changes did not significantly influence the long bone fracture risk.

Conclusions: The present study reviewed the geometrical changes in car front-ends along with regulatory concerns regarding pedestrian safety. A preliminary quantitative benefit of the lower extremity injury reduction was estimated based on these geometrical features. Further investigation is recommended on the structural changes and inclusion of more accident scenarios.     

Effects of Vehicle Impact Velocity and Front-End Structure on Dynamic Responses of Child Pedestrians

To investigate the effects of vehicle impact velocity and front-end structure on the dynamic responses of child pedestrians, an extensive parametric study was carried out using two child mathematical models at 6 and 15 years old. The effect of the vehicle impact velocity was studied at 30, 40, and 50 km/h in terms of the head linear velocity, impact angle, and head angular velocity as well as various injury parameters concerning the head, chest, pelvis, and lower extremities. The variation of vehicle front-end shape was determined according to the shape corridors of modern vehicles, while the stiffness characteristics of the bumper, hood edge, and hood were varied within stiffness corridors obtained from dynamic component tests. The simulation results show that the vehicle impact speed is of great importance on the kinematics and resulting injury severity of child pedestrians. A significant reduction in all injury parameters can be achieved as the vehicle impact speed decreases to 30 km/h. The head and lower extremities of children are at higher injury risks than other body regions. Older children are exposed to higher injury risks to the head and lower leg, whereas younger ones sustain more severe impact loads to the pelvis and upper leg. The results from factorial analysis indicate that the hood-edge height has a significant effect on the kinematics and head impact responses of children. A higher hood edge could reduce the severity of head impact for younger children, but aggravate the risks of head injury for older ones. A significant interaction exists between the bumper height and the hood-edge height on the head impact responses of younger child. Nevertheless, improving the energy absorption performance of the hood seems effective for mitigating the severity of head injuries for children.     

Effects of vehicle impact velocity and front-end structure on dynamic responses of child pedestrians

To investigate the effects of vehicle impact velocity and front-end structure on the dynamic responses of child pedestrians, an extensive parametric study was carried out using two child mathematical models at 6 and 15 years old. The effect of the vehicle impact velocity was studied at 30, 40, and 50 km/h in terms of the head linear velocity, impact angle, and head angular velocity as well as various injury parameters concerning the head, chest, pelvis, and lower extremities. The variation of vehicle front-end shape was determined according to the shape corridors of modern vehicles, while the stiffness characteristics of the bumper, hood edge, and hood were varied within stiffness corridors obtained from dynamic component tests. The simulation results show that the vehicle impact speed is of great importance on the kinematics and resulting injury severity of child pedestrians. A significant reduction in all injury parameters can be achieved as the vehicle impact speed decreases to 30 km/h. The head and lower extremities of children are at higher injury risks than other body regions. Older children are exposed to higher injury risks to the head and lower leg, whereas younger ones sustain more severe impact loads to the pelvis and upper leg. The results from factorial analysis indicate that the hood-edge height has a significant effect on the kinematics and head impact responses of children. A higher hood edge could reduce the severity of head impact for younger children, but aggravate the risks of head injury for older ones. A significant interaction exists between the bumper height and the hood-edge height on the head impact responses of younger child. Nevertheless, improving the energy absorption performance of the hood seems effective for mitigating the severity of head injuries for children.     

Effect of posture on forces and moments measured in a Hybrid III ATD lower leg

Objective: Anthropomorphic test devices (ATDs) are used to assess real injury risk to occupants of vehicles during injurious events. In the lower leg, values from load cells are compared to injury criteria developed in cadaveric studies. These criteria are typically developed with the leg in a neutral posture, whereas the ATD may assume a wide range of postures during safety evaluation tests. The degree to which the initial posture of an ATD has an effect on the measured forces and moments in the lower leg is unknown.

Methods: A Hybrid III ATD lower leg was impacted in a range of postures under conditions representing a crash test, and peak axial force and adjusted tibia index injury measures were evaluated. Ankle posture was varied in 5° increments using a custom-made footplate, and dorsi/plantarflexion (20° DF to 20° PF) and in/eversion (20° IV to 5° EV) were evaluated. Tibia angle was also varied (representing knee flexion/extension) by ±10° from neutral.

Results: Peak axial force was not affected by ankle flexion or tibia angulation. Adjusted tibia index was lowest for plantarflexion, as well as for tibia angles representative of knee extension. Both peak axial force and adjusted tibia index were lowest for postures of great inversion and were highest in neutral or near-neutral postures.

Conclusions: The range of postures tested herein spanned published injury criteria and thus would have made the difference between pass and fail in a safety evaluation. In/eversion had the largest influence on injury metrics, likely due to the change in axial stiffness and altered impact durations in these postures. Results suggest increased injury risk at neutral or near-neutral postures, whereas previous cadaveric studies have suggested that in/eversion does not influence injury risk. It is unclear whether the ATD appropriately represents the natural lower leg for impacts in out-of-position testing. Great care must be taken when initially positioning ATDs for safety evaluations, because small perturbations in posture were shown herein to have large effects on the measured injury risk using this tool.     

Effects of vehicle impact velocity, vehicle front-end shapes on pedestrian injury risk

Objective: This study aimed at investigating the effects of vehicle impact velocity, vehicle front-end shape, and pedestrian size on injury risk to pedestrians in collisions with passenger vehicles with various frontal shapes. Method: A series of parametric studies was carried out using 2 total human model for safety (THUMS) pedestrian models (177 and 165?cm) and 4 vehicle finite element (FE) models with different front-end shapes (medium-size sedan, minicar, one-box vehicle, and sport utility vehicle [SUV]). The effects of the impact velocity on pedestrian injury risk were analyzed at velocities of 20, 30, 40, and 50?km/h. The dynamic response of the pedestrian was investigated, and the injury risk to the head, chest, pelvis, and lower extremities was compared in terms of the injury parameters head injury criteria (HIC), chest deflection, and von Mises stress distribution of the rib cage, pelvis force, and bending moment diagram of the lower extremities. Result: Vehicle impact velocity has the most significant influence on injury severity for adult pedestrians. All injury parameters can be reduced in severity by decreasing vehicle impact velocities. The head and lower extremities are at greater risk of injury in medium-size sedan and SUV collisions. The chest injury risk was particularly high in one-box vehicle impacts. The fracture risk of the pelvis was also high in one-box vehicle and SUV collisions. In minicar collisions, the injury risk was the smallest if the head did not make contact with the A-pillar. Conclusion: The vehicle impact velocity and vehicle front-end shape are 2 dominant factors that influence the pedestrian kinematics and injury severity. A significant reduction of all injuries can be achieved for all vehicle types when the vehicle impact velocity is less than 30?km/h. Vehicle designs consisting of a short front-end and a wide windshield area can protect pedestrians from fatalities. The results also could be valuable in the design of a pedestrian-friendly vehicle front-end shape. [Supplementary materials are available for this article. Go to the publisher's online edition of Traffic Injury Prevention for the following free supplemental resource: Head impact conditions and injury parameters in four-type vehicle collisions and validation result of the finite element model of one-box vehicle and minicar. ].     

The influence of lower extremity postures on kinematics and injuries of cyclists in vehicle side collisions

Objective: A cyclist assumes various cyclic postures of the lower extremities while pushing the pedals in a rotary motion while pedaling. In order to protect cyclists in collisions, it is necessary to understand what influence these postures have on the global kinematics and injuries of the cyclist.

Method: Finite element (FE) analyses using models of a cyclist, bicycle, and car were conducted. In the simulations, the Total Human Model of Safety (THUMS) occupant model was employed as a cyclist, and the simulation was set up such that the cyclist was hit from its side by a car. Three representative postures of the lower extremities of the cyclist were examined, and the kinematics and injury risk of the cyclist were compared to those obtained by a pedestrian FE model. The risk of a lower extremity injury was assessed based on the knee shear displacement and the tibia bending moment.

Results: When the knee position of the cyclist was higher than the hood leading edge, the hood leading edge contacted the leg of the cyclist, and the pelvis slid over the hood top and the wrap-around distance (WAD) of the cyclist's head was large. The knee was shear loaded by the hood leading edge, and the anterior cruciate ligament (ACL) ruptured. The tibia bending moment was less than the injury threshold. When the cyclist's knee position was lower than the hood leading edge, the hood leading edge contacted the thigh of the cyclist, and the cyclist rotated with the femur as the pivot point about the hood leading edge. In this case, the head impact location of the cyclist against the car was comparable to that of the pedestrian collision. The knee shear displacement and the tibia bending moment were less than the injury thresholds.

Conclusion: The knee height of the cyclist relative to the hood leading edge affected the global kinematics and the head impact location against the car. The loading mode of the lower extremities was also dependent on the initial positions of the lower extremities relative to the car structures. In the foot up and front posture, the knee was loaded in a lateral shear direction by the hood leading edge and as a result the ACL ruptured. The bicycle frame and the struck-side lower extremity interacted and could influence the loadings on lower extremities.     

The role of door orientation on occupant injury in a nearside impact: a CIREN, MADYMO modeling and experimental study

OBJECTIVE: This study addressed the effects of vehicle height mismatch in side impact crashes. A light truck or SUV tends to strike the door of a passenger car higher causing the upper border to lead into the occupant space. Conversely, an impact centered lower on the door, from a passenger car, causes the lower border to lead. We proposed the hypothesis that the type of injury sustained by the occupant could be related to door orientation during its intrusion into the passenger compartment. METHOD: Data on door orientation and nearside occupant injuries were collected from 125 side impact crashes reported in the CIREN database. Experimental testing was performed using a pendulum carrying a frame and a vehicle door, impacting against a USDOT SID. The frame allowed the door orientation to be changed. A model was developed in MADYMO (v 6.2) using the more biofidelic dummies, BIOSID, and SIDIIs as well as USDOT SID. RESULTS: In side impact crashes with the lower border of the door leading, 81% of occupants sustained pelvic injury, 42% suffered rib fractures, and the rate of organ injury was 0.84. With the upper border leading, 46% of occupants sustained pelvic injury, 71% sustained rib fracture, and the rate of organ injuries per case increased to 1.13. The differences in the groups with respect to pelvic injury were significant at p = 0.01, rib fracture, p = 0.10, and organ injury, p = 0.001. Experimental testing showed that when the door angle changed from lower to upper border leading, peak T4 acceleration increased by 273% and pelvic acceleration decreased by 44%. The model demonstrated that when the door angle changed from lower to upper border leading, the USDOT SID showed a 29% increase in T4 acceleration and a 57% decrease in pelvic acceleration. The BIOSID dummy demonstrated a 36% increase in T1 acceleration, a 44% increase in abdominal rib 1 deflection, a 91% increase in thoracic rib 1 deflection, and a 33% decrease in pelvic acceleration. CONCLUSIONS: These data add more insight to the problem of mismatch during side impacts, where the bumper of the striking vehicle overrides the door beam, causing the upper part of the door to lead the intrusion into the passenger compartment. Even with the same delta V and intrusion, with the upper border of the door leading, more severe chest and organ injuries resulted. This data suggests that door orientation should be considered when testing subsystems for side impact protection.     

Estimated Injury Risk for Specific Injuries and Body Regions in Frontal Motor Vehicle Crashes

Objective: Injury risk curves estimate motor vehicle crash (MVC) occupant injury risk from vehicle, crash, and/or occupant factors. Many vehicles are equipped with event data recorders (EDRs) that collect data including the crash speed and restraint status during a MVC. This study's goal was to use regulation-required data elements for EDRs to compute occupant injury risk for (1) specific injuries and (2) specific body regions in frontal MVCs from weighted NASS-CDS data.

Methods: Logistic regression analysis of NASS-CDS single-impact frontal MVCs involving front seat occupants with frontal airbag deployment was used to produce 23 risk curves for specific injuries and 17 risk curves for Abbreviated Injury Scale (AIS) 2+ to 5+ body region injuries. Risk curves were produced for the following body regions: head and thorax (AIS 2+, 3+, 4+, 5+), face (AIS 2+), abdomen, spine, upper extremity, and lower extremity (AIS 2+, 3+). Injury risk with 95% confidence intervals was estimated for 15–105 km/h longitudinal delta-Vs and belt status was adjusted for as a covariate.

Results: Overall, belted occupants had lower estimated risks compared to unbelted occupants and the risk of injury increased as longitudinal delta-V increased. Belt status was a significant predictor for 13 specific injuries and all body region injuries with the exception of AIS 2+ and 3+ spine injuries. Specific injuries and body region injuries that occurred more frequently in NASS-CDS also tended to carry higher risks when evaluated at a 56 km/h longitudinal delta-V. In the belted population, injury risks that ranked in the top 33% included 4 upper extremity fractures (ulna, radius, clavicle, carpus/metacarpus), 2 lower extremity fractures (fibula, metatarsal/tarsal), and a knee sprain (2.4–4.6% risk). Unbelted injury risks ranked in the top 33% included 4 lower extremity fractures (femur, fibula, metatarsal/tarsal, patella), 2 head injuries with less than one hour or unspecified prior unconsciousness, and a lung contusion (4.6–9.9% risk). The 6 body region curves with the highest risks were for AIS 2+ lower extremity, upper extremity, thorax, and head injury and AIS 3+ lower extremity and thorax injury (15.9–43.8% risk).

Conclusions: These injury risk curves can be implemented into advanced automatic crash notification (AACN) algorithms that utilize vehicle EDR measurements to predict occupant injury immediately following a MVC. Through integration with AACN, these injury risk curves can provide emergency medical services (EMS) and other patient care providers with information on suspected occupant injuries to improve injury detection and patient triage.     

Investigation of Motorcyclist Cervical Spine Trauma Using HUMOS Model

Objective: With 16 percent of the total road user fatalities, motorcyclists represent the second highest rate of road fatalities in France after car occupants. Regarding road accidents, a large proportion of trauma was on the lower cervical spine. According to different clinical studies, it is postulated that the cervical spine fragility areas are located on the upper and lower cervical spine. In motorcycle crashes, impact conditions occur on the head segment with various orientations and impact directions, leading to a combination of rotations and compression. Hence, motorcyclist vulnerability was investigated considering many impact conditions. Method: Using the human model for safety (HUMOS), a finite element model, this work aims to provide an evaluation of the cervical spine weaknesses based on an evaluation of injury mechanisms. This evaluation consisted of defining 2 injury risk factors (joint injury and bone fracture) using a design of experiment including various velocities, impact directions, and impact orientations. Results: The results confirmed previously reported clinical and epidemiological work on the fragility of the lower cervical spine and the upper cervical spine segments. Joint injuries appeared before bone fractures on both the upper and lower cervical spine. Bone fracture risk was greater on the lower cervical spine than on the upper cervical spine. The compression induced by a high impact angle was identified as an important injury severity factor. It significantly increased the injury incidence for both joint injuries and bone fractures. It also induced a shift in injury location from the lower to the upper cervical spine. The impact velocity exhibited a linear relationship with injury risks and severity. It also shifted the bone fracture risk from the lower to upper spinal segments.     

Safer Truck Front Design for Pedestrian Impacts*

Truck and bus frontal impacts account for a major proportion of pedestrian fatalities in many less motorized countries. To understand this phenomenon, we have collected injury data on pedestrian impacts with buses and trucks and performed computer simulations to identify critical design parameters at 15–45 km/h impact velocities for further investigation. A male dummy which was scaled to fifty percentile Indian dimensions has been used for simulations using MADYMO. Bumper height, bumper offset and grille inclination affect the pelvis and thorax forces and Head Injury Criterion values critically. Bumper width has less effect. Simulations were performed to optimize for the above–mentioned three parameters. Changes in front geometric parameters reduce injury to the upper body and head below safety limits for the existing force–displacement properties but do not affect leg injuries significantly. Hence bumpers need to be made less stiff. Injury data shows that pedestrians also sustain tibia fractures in bus/truck impacts in apparent low velocity impacts. The computer modeling does not offer adequate explanation for this phenomenon. These simulations confirm that it is theoretically possible to make truck/bus fronts safer for pedestrians in impacts up to 35 km/h.     

Driver Injury Risk Variability in Finite Element Reconstructions of Crash Injury Research and Engineering Network (CIREN) Frontal Motor Vehicle Crashes

Objective: A 3-phase real-world motor vehicle crash (MVC) reconstruction method was developed to analyze injury variability as a function of precrash occupant position for 2 full-frontal Crash Injury Research and Engineering Network (CIREN) cases.

Method: Phase I: A finite element (FE) simplified vehicle model (SVM) was developed and tuned to mimic the frontal crash characteristics of the CIREN case vehicle (Camry or Cobalt) using frontal New Car Assessment Program (NCAP) crash test data. Phase II: The Toyota HUman Model for Safety (THUMS) v4.01 was positioned in 120 precrash configurations per case within the SVM. Five occupant positioning variables were varied using a Latin hypercube design of experiments: seat track position, seat back angle, D-ring height, steering column angle, and steering column telescoping position. An additional baseline simulation was performed that aimed to match the precrash occupant position documented in CIREN for each case. Phase III: FE simulations were then performed using kinematic boundary conditions from each vehicle's event data recorder (EDR). HIC15, combined thoracic index (CTI), femur forces, and strain-based injury metrics in the lung and lumbar vertebrae were evaluated to predict injury.

Results: Tuning the SVM to specific vehicle models resulted in close matches between simulated and test injury metric data, allowing the tuned SVM to be used in each case reconstruction with EDR-derived boundary conditions. Simulations with the most rearward seats and reclined seat backs had the greatest HIC15, head injury risk, CTI, and chest injury risk. Calculated injury risks for the head, chest, and femur closely correlated to the CIREN occupant injury patterns. CTI in the Camry case yielded a 54% probability of Abbreviated Injury Scale (AIS) 2+ chest injury in the baseline case simulation and ranged from 34 to 88% (mean = 61%) risk in the least and most dangerous occupant positions. The greater than 50% probability was consistent with the case occupant's AIS 2 hemomediastinum. Stress-based metrics were used to predict injury to the lower leg of the Camry case occupant. The regional-level injury metrics evaluated for the Cobalt case occupant indicated a low risk of injury; however, strain-based injury metrics better predicted pulmonary contusion. Approximately 49% of the Cobalt occupant's left lung was contused, though the baseline simulation predicted 40.5% of the lung to be injured.

Conclusions: A method to compute injury metrics and risks as functions of precrash occupant position was developed and applied to 2 CIREN MVC FE reconstructions. The reconstruction process allows for quantification of the sensitivity and uncertainty of the injury risk predictions based on occupant position to further understand important factors that lead to more severe MVC injuries.