Leaching characteristics of PCDDs/DFs and dioxin-like PCBs from landfills containing municipal solid waste and incineration residues

To investigate the leaching characteristic of persistent organic pollutants (POPs), such as non-ortho and mono-ortho substituted chlorobiphebyls (dioxin-like PCBs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/DFs), in leachate from municipal solid waste (MSW) landfill sites containing incineration residues, raw leachate samples were collected twice from 12 selected MSW landfill sites. The samples were divided into their liquid and solid phases using GF/B (pore size 1.0 microm), and the concentrations of POPs then determined. The concentrations of PCDDs/DFs ranged from 0.65 to 5.88 pg-TEQ/l (average 2.86 pg-TEQ/l), and those of dioxin-like PCBs from 0.05 to 0.32 pg-TEQ/l (average 0.18 pg-TEQ/l). The major congeners of leached PCDDs/DFs and dioxin-like PCBs in liquid and solid phases were OCDD (about 60%), 2,3',4,4',5-PeCBs (about 30%), and 2,3,4,4',5-PeCBs (about 54%). The relationship between landfill age and the leaching concentration of PCDDs/DFs, and effects of dissolved organic carbon (DOC) on the leaching of PCDDs/DFs are also discussed. Finally, a leaching prediction model of PCDDs/DFs from MSW landfills has been suggested using parameters, such as hydrophobic neutral organic carbons, total dissolved solid, and the ratio of non-biodegradable wastes in landfill sites.     

Effect of dissolved humic matters on the leachability of PCDD/F from fly ash--laboratory experiment using Aldrich humic acid

The effect of dissolved humic matters (DHM) on the leachability of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) in fly ash was studied theoretically and in laboratorial condition to verify the previous results for pilot and field experiment of incineration residues landfill. In theoretical review, it was shown that DHM could influence the actual solubility and leachability of PCDD/F. The higher concentration of DHM showed the higher leachability of PCDD/F. In the leaching test, three different DHM concentrations and pHs of solutions were adopted to fly ash samples imaging the various characteristics of municipal solid waste leachate. It was proved experimentally that the leachability of PCDD/F increased with increasing DHM concentration in all pH conditions. The highest leachability was shown at the highest pH. Isomer distribution patterns of PCDD/F in all leachates were similar in all pH conditions. It backed up the distribution theory of PCDD/F between DHM and water.     

Distribution of polychlorinated dibenzo-p-dioxins and dibenzofurans in suspended sediments, dissolved phase and bottom sediment in the Houston Ship Channel

Spatial distributions of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) in the water column and bottom sediments of the Houston Ship Channel in Texas were measured three times over a 1-year period. Total TEQ concentrations in water ranged from 0.01 to 0.25 pg/l for the dissolved phase and from 0.09 to 2.91 pg/l for the suspended phase, while TEQ concentrations in bottom sediments varied from 0.9 to 139.8 ng/kg dry wt. The dissolved concentrations were lower than their respective suspended concentrations, with average dissolved/suspended ratios between 0.11 and 0.59 for individual congeners. More than 89% of the total concentration of 2378-substituted PCDD/PCDFs was attributable to OCDD but 2378-TCDD was the major contributor to total TEQ for the three sampled media. Average logs of organic carbon-normalized suspended sediment-dissolved partitioning coefficients (logK(oc)(obs)) varied between 4.92 and 8.59 l/kg-oc; while in the bottom sediment-dissolved interface, logK(oc)(obs) values ranged from 5.48 to 8.48 l/kg-oc. Observed logK(oc)values varied within a factor of 0.64-1.26 from equilibrium logK(oc) values, suggesting fluxes of PCDD/PCDFs across the interfaces. It was found that in the HSC, on average, the tendency of a compound to move from the particulate phase to the dissolved phase decreases with increasing K(ow).     

Levels and characteristic homologue patterns of polychlorinated dibenzo-p-dioxins and dibenzofurans in various incinerator emissions and in air collected near an incinerator

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were monitored in stack gas and fly ash of various Korean incinerators and in air samples collected near the facilities. Concentrations of PCDD/Fs in emissions were investigated, and characteristic PCDD/F homologue patterns were classified using statistical analyses. The PCDD/F emission levels in stack gas and fly ash samples from small incinerators (SIs) were higher than those from municipal solid waste incinerators (MSWIs). The PCDD/F concentrations ranged between 0.38 and 1.16 pg I-TEQ/m3 (21.2-75.2 pg/m3) in ambient air samples. The lower-chlorinated furans were the dominant components in most of the stack gas and fly ash samples from SIs, although this was not the case for fly ash from MSWIs. This homologue pattern is consistent with other studies reporting a high fraction of lower-chlorinated furans in most environmental samples affected by incinerator emissions, and it can be used as an indicator to assess the impact of such facilities on the surrounding environment.     

Effects of injected activated carbon and solidification treatment on the leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans from air pollution control residues of municipal waste incineration

To assess the effectiveness of the injected activated carbon, cement, and sulfur-containing chelating agent in controlling polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) release from the surface of air pollution control (APC) residues, this study examined the leachability of PCDD/Fs from APC residues generated by municipal solid waste incinerators. Results showed that PCDD/Fs were stably retained in the APC residues when the samples were leached with acetic acid solution. Highly chlorinated PCDD/F homologues (i.e., hepta- and octa-CDDs and CDFs) were relatively easy to leach. The leaching percentages of PCDD/Fs from raw APC residue samples containing activated carbon were smaller than those from samples without activated carbon, especially when n-hexane was used as the leachant. These results indicate that the flue gas injected activated carbon not only controls PCDD/F emissions, but also suppresses the leachability of PCDD/Fs from the APC residues. Solidification/stabilization (S/S) processes with 30wt% cement and 5wt% sulfur-containing agent can additionally decrease the leachability of PCDD/Fs with humic acid. Using n-hexane as the leachant, S/S processes increased the leachability of PCDD/Fs. Various low chlorinated PCDD/F congeners were moreover leached out of the APC residue samples, markedly increasing the leachate toxicity. The enhancement of leachability and toxicity owing to S/S processes may negatively impact the environment when APC residues are exposed to nonpolar organic solvents.     

Influence of a municipal solid waste incinerator on ambient air and soil PCDD/Fs levels

To examine the influence of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) emissions from a municipal solid waste incinerator (MSWI) on the environment, we measured the levels of PCDD/Fs in ambient air and soil samples collected near a MSWI in Bucheon, Korea. The PCDD/Fs concentrations in the ambient air samples ranged from 0.22 to 1.16 pg I-TEQm(-3) (13.39-75.16 pg m(-3)), with an average of 0.66 pg I-TEQ m(-3) (35.62 pg m(-3)). The soil samples contained between 1.25 and 74.98 pg I-TEQ g(-1) (38.15-3,303.33 pg g(-1)), with an average of 19.06 pg I-TEQ g(-1) (1,077.11 pg g(-1)). These levels were higher than those previously reported by other investigators in a number of surveys. The furan homologues predominated in the air samples and some soil samples, and the soil PCDD/Fs levels decreased with increasing distance from the MSWI. Comparison of the homologue patterns and a multivariate statistical analysis showed that PCDD/Fs emission from the MSWI directly affected the pattern of PCDD/Fs in air, while the PCDD/Fs patterns in soil differed according to the location relative to the MSWI, roads, and construction sites. These results collectively indicate that the MSWI was the major PCDD/Fs emission source in this area, but that unidentified combustion sources and vehicles might influence the environment to some extent.     

Effect of reaction time on PCDD and PCDF formation by de novo synthetic reactions under oxygen deficient and rich atmosphere

The effect of reaction time on formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) was studied under laboratory conditions in the system containing municipal waste incineration fly ash, activated carbon and copper chloride dihydrate at 300 degrees C in 99.999% N2 and N2 + 10% O2 atmosphere. The concentrations of tetra- to octa-chlorinated isomers as well as I-TEQ concentrations of toxic congeners are reported. The mechanism of PCDD and PCDF formation from chlorophenols and chlorinated biphenyls is discussed in the light of the time changes of PCDD/PCDF ratios.     

PCDD/DF concentrations at the inlets and outlets of wet scrubbers in Korean waste incinerators

To further understand the effects of wet scrubbers on PCDD/DF levels, it was measured the concentrations of PCDD/DF, dust, and other gaseous pollutants at both the inlets and the outlets of seven wet scrubbers. As a result, the concentrations of PCDD/DF at the inlets and outlets of the wet scrubbers ranged from 0.2 to 37.4, and 0.8 to 6.0 ng TEQ N m-3, respectively. With the exceptions of wet scrubbers F and G, the PCDD/DF levels decreased by and large in most wet scrubbers. It was thought that their relatively high removal efficiencies were more increased with heavier loads of dust and particle-bound PCDD/DF. On the other hand, it was also surveyed the increase of gaseous PCDD/DF in wet scrubber, where the total level of PCDD/DF was decreased. However, it was not sure whether it had been resulted from the thermal adsorption/desorption phenomenon between packing materials and emission gases or not. At the very least, however, although there still remains an unexplained aspect for the increase of gaseous PCDD/DF, it is clear that wet scrubbers can be sufficiently applied to remove PCDD/DF to a certain extent, if only removal efficiencies for the particle loads are high, and if a significant part of the PCDD/DF at the inlets is particle associated.     

PCDD/Fs levels in indoor environments and blood of workers of three municipal waste incinerators in Taiwan

This study monitored ambient air concentrations of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in three municipal waste incineration plants. Blood PCDD/Fs levels of 133 workers randomly selected from these plants were also measured. The associations between workers' blood PCDD/Fs concentrations and occupational exposures to PCDD/Fs were assessed. Means of air PCDD/Fs levels ranged from 0.08 to 3.01 pg/m3 in international toxic equivalents (I-TEQ). The geometric means of blood PCDD/Fs concentrations were 14.6, 15.8, 19.1 pg/g lipid in World Health Organization (WHO) TEQ, respectively, for workers from three plants. Air levels of total I-TEQ and all congeners, except 2,3,7,8-tetrachlorinated dibenzo-p-dioxin (TeCDD) and 1,2,3,4,7,8,9-heptachlorinated dibenzofuran (HpCDF), were significantly higher in plant B. However, blood concentrations of 2,3,7,8-TeCDD, 1,2,3,7,8-PeCDD, 2,3,7,8-TeCDF, 1,2,3,7,8-PeCDF and 1,2,3,4,7,8,9-HpCDF were significantly elevated in plant C workers. Although job contents, duration of employment and time spent in certain location were significantly different among incineration plants, they were not significantly associated with blood concentrations of any congener. Furthermore, results of the multiple regression analysis that assessed important occupational factors simultaneously and adjusted for potential confounders, showed significant associations between four congeners and incineration plant or job contents. However, the results were limited by small R-squares of the regression models. In conclusion, blood concentrations of several PCDD/Fs congeners were significantly different among three incineration plants. The differences were not explained by the discrepancy in job contents, duration of employment, and time activity in these plants.     

Degradation of PCDD, PCDF, PAH, PCB and chlorinated phenols during the destruction-treatment of landfill seepage water in laboratory model reactor (UV, Ozone, and UV/Ozone)

Seepage water of toxic waste landfills is polluted with high concentrations of toxic organic compounds. The concentrations in the seepage water we applied for chlorinated phenols are between 2 μg/1 and 1 mg/l, for PCB between 800 pg/l and 250 ng/l, for PAH between 200 ng/l and 12 μg/l and for PCDD and PCDF between 20 pg/l and 1 ng/l. Usual purification methods produce highly contaminated residues, which have to be treated by pyrolysis or are deposited again at a landfill. A better way is to destruct these contaminants by UV/ozone treatment. The treatment of seepage water by UV-irradiation, ozone and UV/ozone is compared. Results show no significant effect during all treatments for PCB and PCDD/PCDF. The chlorinated phenols and PAH were mostly destroyed by UV/ozone treatment more than 90 %. The pH value has no influence on the UV/ozone treatment of seepage water.     

Dioxins,chlorophenols and other chlorinated organic pollutants in colloidal and water fractions of groundwater from a contaminated sawmill site

BACKGROUND, AIM, AND SCOPE: The distribution of chlorinated organic contaminants in groundwater and the importance of colloids were studied in groundwater from a sawmill site contaminated by chlorophenol preservatives. MATERIALS AND METHODS: The groundwater was fractionated into three different size ranges: (1) >0.7 mum, (2) 0.4-0.7 mum and (3) 0.2-0.4 mum and the filtered water phase. The concentrations of chlorophenols (CP), chlorinated phenoxy phenols (PCPP), chlorinated diphenyl ethers (PCDE), chlorinated dibenzofurans (PCDF) and chlorinated dibenzo-p-dioxins (PCDD) were determined in each fraction. The colloids were characterised regarding the chemical composition using X-ray photoelectron spectroscopy (XPS). RESULTS: Chlorophenols were mostly found in the water fraction and PCDD/Fs were found almost exclusively in the particulate fractions. For example, the filtered water phase contained 2,100 mug l(-1) and 0.72 ng l(-1) for CPs and PCDD/Fs, respectively, and the particulate fractions contained 27 mug l(-1) and 32 ng l(-1) for CPs and PCDD/Fs, respectively. XPS evaluation of the particulate phases showed no correlation between the surface chemistry of the particle properties and the distribution of chlorinated compounds. DISCUSSION: The results suggest that groundwater transport of CPs, PCPPs, PCDEs and PCDD/Fs may occur from contaminated sawmill sites and that the colloid-facilitated transport, especially of PCDD/Fs, is substantial. The results correlated well with previous studies of compounds sorbed to dissolved organic carbon, which indicate that dissolved and colloidal organic carbon facilitated the transport of PCDEs, PCDFs and PCDDs particularly. CONCLUSIONS: Several classes of chlorinated compounds were readily detected in the groundwater samples. Due to the differences in their physicochemical properties, CPs, PCPPs, PCDEs and PCDD/Fs vary in their partitioning between colloidal fractions and the filtered groundwater. The proportion of the bound fraction increased with an increasing hydrophobicity of the chlorinated compounds. The groundwater transport of colloid-associated pollutants from the site may be significant. RECOMMENDATIONS AND PERSPECTIVES: The results imply that colloidal particles <0.7 mum are freely mobile in groundwater from this site. The groundwater transport of colloid-associated pollutants may be significant. However, the extent of the problem is not yet known and, thus, further research is needed to evaluate the impact of colloidal transport of hydrophobic organic contaminants. In Sweden alone, 400 to 500 sawmill sites are estimated to be contaminated with PCDD/Fs as a result of the former use of CP-based wood preservatives. The widespread use of CP mixtures for a variety of applications, including wood preservation, indicates that potential colloidal transport will be an issue of concern in many countries.     

Kinetics of carbon degradation and PCDD/PCDF formation on MSWI fly ash

The native carbon oxidation and PolyChloroDibenzo-p-Dioxins and PolyChloroDibenzoFurans, PCDD/F, formation were simultaneously studied at different temperatures (230-350 degrees C) and times (0-1440 min) in order to establish a direct correlation between the disappearance of the reagent and the formation of the products. The kinetic runs were conducted in an experimental set up where conditions were chosen to gain information on the role of fly ash deposits in cold zones of municipal solid waste incinerators in PCDD/F formation reaction. The carbon oxidation measured as the decrease of total organic carbon of fly ash was in agreement with the carbon evolved as sum of CO and CO(2). The carbon mass balance indicated an increase in the efficiency of carbon conversion in CO and CO(2) with temperature. The CO and CO(2) formation was the result of two parallel pseudo first order reactions thus giving significant information about the reaction mechanism. PCDD/F formation as a function of temperature showed that the maximum formation was achieved in a narrow range around 280 degrees C; the time effect at 280 degrees C was a progressive formation increase at least up to 900 min. The PCDF:PCDD molar ratio increased with temperature and time, and the most abundant homologues were HxCDD, HpCDD, OCDD for PCDD, and HxCDF, HpCDF within PCDF. These experimental results supported the hypothesis that the formation mechanism was the de novo synthesis.     

The prediction of PCDD/DF levels in wet scrubbers associated with waste incinerators

Wet scrubber is one of the most conventional types of air pollutant control devices (APCDs), which is specially designed to treat dust and acidic gases in the flue gas simultaneously. In spite of its outstanding ability to control them, however, wet scrubbers have been considered as potential contaminant sources that may increase PCDD/DF concentrations in the flue gas. In this study, we investigated the change of PCDD/DF concentrations at the inlets and outlets of seven wet scrubbers, and compared them with other published data. With a multi-regression analysis of dust concentrations and temperature at the inlets and outlets of given wet scrubbers, we developed an empirical model to understand factors dominating the change of PCDD/DF concentrations. As a result, we confirmed that the changes of PCDD/DF concentrations in wet scrubbers are closely related to their concentrations at the inlets, which would usually be determined by the type of APCDs installed upstream of the wet scrubber.     

Occurrence, possible sources, and temporal trends of polychlorinated dibenzo-p-dioxins and dibenzofurans in water and sediment from the lower Yangtze River basin, Jiangsu and Shanghai areas of Eastern China

The concentrations, compositional profiles, and possible sources of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) in water column and surface sediment samples from the lower reaches of the Yangtze River were investigated, and the potential risks posed by these chemicals were evaluated. Concentrations of the 17 2,3,7,8-substituted PCDD/PCDF in the water and sediment samples ranged from 0.45 to 10.0 pg TEQ/L (mean 2.34 pg TEQ/L) and from 0.31 to 51 pg TEQ/g dw (mean 5.25 pg TEQ/g dw), respectively. Water and sediments from the Nanjing–Nantong sections of the Yangtze River were found to have elevated PCDD/PCDF levels, and the PCDD/PCDF TEQ concentrations in 13 sediment samples exceeded the probable effect levels (PEL), above which adverse biological effects are likely. Multivariate statistical analysis indicated that the principal PCDD/PCDF contamination source for the water and sediment was the production and use of pentachlorophenol (PCP) or sodium pentachlorophenate (PCP-Na). PCDD/PCDF concentrations were stable over time near the Yangtze River Estuary but had increased sharply in recent decades in the Nanjing–Nantong section, which will have been related to the growth in industrial activities and other anthropogenic PCDD/PCDF sources. Total organic carbon (TOC) and PCDD/PCDF concentrations correlated significantly (R?=?0.474, P?<?0.01), suggesting that TOC plays an important role in the transport and re-distribution of PCDD/PCDF in the Yangtze River basin.     

Partitioning and removal of dioxin-like congeners in flue gases treated with activated carbon adsorption

Activated carbon adsorption is commonly used to control dioxin-like congener (PCDD/Fs and PCBs) emissions. Partitioning of PCDD/Fs and PCBs between vapor and solid phases and their removal efficiencies achieved with existing air pollution control devices (APCDs) at a large-scale municipal waste incinerator (MWI) and an industrial waste incinerator (IWI) are evaluated via intensive stack sampling and analysis. Those two facilities investigated are equipped with activated carbon injection (ACI) with bag filter (BF) and fixed activated carbon bed (FACB) as major PCDD/F control devices, respectively. Average PCDD/F and PCB concentrations of stack gas with ACI+BF as APCDs are 0.031 and 0.006ng-TEQ/Nm(3), and that achieved with FACB are 1.74 and 0.19ng-TEQ/Nm(3) in MWI and IWI, respectively. The results show that FACB could reduce vapor-phase PCDD/Fs and PCBs concentrations in flue gas, while the ACI+BF can effectively adsorb the vapor-phase dioxin-like congener and collect the solid-phase PCDD/Fs and PCBs in the meantime. Additionally, the results of the pilot-scale adsorption system (PAS) experimentation indicate that each gram activated carbon adsorbs 105-115ng-PCDD/Fs and each surface area (m(2)) of activated carbon adsorbs 10-25ng-PCDD/Fs. Based on the results of PAS experimentation, this study confirms that the surface area of mesopore+macropore (20-200A) of the activated carbon is a critical factor affecting PCDD/F adsorption capacity.     

Dioxin mass balance in a municipal waste incinerator

A dioxin mass balance in an Spanish municipal waste incinerator (MWI) is presented. Input and output inventories from two sampling collection episodes including the analysis of PCDD/PCDF in urban solid waste (USW), stack gas emissions, fly ash and slag are reported. In one collection the levels of USW were around 8 pg I-TEQ/g and non-thermal destruction was observed overall. In the other collection the levels of USW were higher (around 64 pg I-TEQ/g) and the dioxin balance revealed a thermal destruction. Analysis of the different waste materials (textile, organic, plastic, wood and paper) was performed separately and the textile samples presented the highest levels.     

Air and soil dioxin levels at three sites in Italy in proximity to MSW incineration plants

Levels of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in both air and soil samples were measured at three different sites in Italy, in proximity to three municipal solid waste incinerators (MSWIs) to determine baseline contamination and the contributory role of incinerator emissions. At the first site, located in an agricultural, cattle-breeding, typically flattish area of the Po Valley, the dioxin concentrations had already been measured before the start-up of the new MSWI. These dioxin concentrations were then again measured after two years of continual operation of the incinerator. Despite the presence of the plant, the PCDD/Fs concentrations appear not to have been affected and were found to be in a range of 22-125 fg I-TEQ m(-3) in the air samples and 0.7-1.5 pg I-TEQ g(-1) in the soil samples. The second site is located in an industrial district of the Veneto Region, in the surroundings of an old MSWI that is not equipped with Best Available Technology (BAT) dioxin removal system. The PCDD/Fs concentrations in the air samples were between 144 and 337 fg I-TEQ m(-3). This is a typical range of values for industrial areas, while the soil samples showed contamination levels between 1.1 and 1.4 pg I-TEQ g(-1). The third site lies in the Adige Valley, near a MSWI that has been equipped with BAT for flue gas cleaning. The observed values ranged from 10 to 67 fg I-TEQ m(-3) for the air samples and 0.08-1.2 pg I-TEQ g(-1) for the soil samples. The contributory factors of the varying characteristics of the different areas together with the types of technology adopted at each MSWI plant are discussed. The PCDD/Fs levels are subsequently compared with established values from previous studies.     

Modelling of PCDD/F release from MSW bio-drying

In the present work, an experimentation was carried out to study the behaviour of PCDD/F during the process of municipal solid waste (MSW) bio-drying. This process belongs to the biological mechanical treatment (BMT) options and is aimed to the dewatering of MSW thanks to the biological exothermal reactions (thermal drying, on the contrary, needs an external heat source as methane). The result is a decrease of waste weight and an increase of lower heating value (as the energy content refers to a lower amount of waste). Of course, the overall energy availability does not increase, but the characteristics of bio-drying are interesting as a way for refuse derived fuel generation: glass, metals and inert removals are easier after bio-drying. The literature of the sector shows only few data on PCDD/F emission to air from BMT. Anyway, in the present work an original theory has been put forward in order to explain the enrichment of PCDD/F in the air exiting the biological processes. The role of the initial PCDD/F concentration in the ambient air entering the plant is obviously taken into account. The results of the developed experimentation and the following elaborations point out that PCDD/F could be freed from the volatile solids consumed during the process. The different amount of PCDD/F in the waste and the different consumption of volatile solids depending on the biological process can explain the different PCDD/F emission factors available in the literature.     

PCDD/F concentrations in milk of nonoccupationally exposed women living in southern Catalonia, Spain

Concentrations of 17 toxic 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) have been determined in pooled samples of breast milk from 15 mothers living in two residential areas (Tarragona downtown and an industrial area) in the vicinity of a new hazardous waste incinerator (HWI), now under construction in Tarragona (southern Catalonia, Spain). PCDD/Fs in human milk samples ranged between 5.9 and 17.1 pg I-TEQ/g fat (162-498 pg I-TEQ/l), with a mean value of 11.8 pg I-TEQ/g fat (310.8 pg I-TEQ/l). The percentages of fat ranged between 1.53 and 3.52. Although PCDD/F levels in milk from mothers living in the industrial area were found to be slightly higher than those observed in women living Tarragona downtown, most differences did not reach the level of statistical significance. In general terms, PCDD/F concentrations in human milk (pooled) samples of mothers living in the area of Tarragona are similar or lower than those previously reported for most industrialized countries.     

Thermal degradation of PCDD/F, PCB and HCB in municipal solid waste ash

A thermal degradation procedure for reducing the concentrations of mono- to octa-chlorinated PCDD/Fs, PCBs and hexa-chlorobenzenes (HCB) in filter ash from incinerated municipal solid waste (MSW) is described. Thermal treatment of filter ash samples at 500 degrees C for 60 min in a closed system providing low oxygen conditions resulted in 97% and 99% reductions in the total and I-TEQ concentrations of PCDD/Fs, to 6.8 microg kg(-1) ash and <0.05 microg I-TEQ kg(-1) ash, respectively. Increasing the thermal treatment time to 480 min, at the same temperature, yielded 99% reductions in both total and I-TEQ concentrations of the mono- to octa-chlorinated PCDD/Fs. Similar effects were observed for HCB and PCBs. The data from this study indicate that PCDD/Fs and other toxic organic compounds in ash from incinerated MSW, can be effectively degraded by this procedure, which combines relatively low-temperatures, short treatment times, and low oxygen conditions.