Influence of surfactants and polymeric adjuvants on physicochemical properties, droplet size spectra and deposition of fenitrothion and Bacillus thuringiensis formulations under laboratory conditions

The effect of two surfactants and two polymeric adjuvants on droplet size spectra and deposition patterns of nine spray formulations was investigated following atomization in a laboratory chamber using a spinning disc atomizer that can produce a narrow droplet size spectrum. Spray droplets were sampled using Kromekote cards and deposit recoveries were examined on glass plates. Physicochemical properties studied were: viscosity-shear rate relationship, surface tension, volatility, pH, conductance, electrophoretic mobility and zeta potential. Formulations containing low surfactant concentrations provided Newtonian liquids with low viscosities. These liquids atomized into small droplets and provided low recoveries of spray deposits on sampling units. However, formulations containing polymeric adjuvants, and a high concentration of a non-ionic surfactant provided pseudoplastic liquids with high viscosities. These formulations resulted in large droplets with high recoveries of spray deposits on sampling units. Among the physicochemical properties studied, viscosity, surface tension, volatility and electrophoretic mobility, played important roles on liquid atomization and droplet deposition.     

Lemna minor membranes affected by adjuvants

The perturbant effects of four Triton adjuvants, namely Triton X-15, X-35, X-100, and X-114 (alkyl aryl polyether alcohols), on some of the biochemical determinants of membrane integrity were determined under laboratory conditions. Two of these, Triton X-100 and X-114, are currently being assessed as emulsifiers for use in fenitrothion insecticidal formulations. Lemna minor L. plants were exposed to 40 microM (10-25 microg ml(-1) in 965 microg mg(-1) Dowanol (tripropylene glycol methyl ether) carrier solvent) adjuvant for a treatment time period of two weeks. A decrease in the contents of the total phospholipids and a concomitant increase in the contents of the galactolipids were found. No change was observed in the total lipid content. An unsaturation occurred in the fatty acids of the total lipids, phospholipids, and monogalactosyl diacylglycerides. This accounted for a significant decrease in palmitic and stearic acids and a concomitant increase in oleic, linoleic, and linolenic acids when these are compared with the fatty acids in the nontreated control sets. The fatty-acid profile of the digalactosyl diacylglycerides, however, differed only slightly from controls. Membrane-fatty-acid unsaturation suggests the possibility of a desaturase enzyme's being induced by these adjuvants.     

Influence of formulation properties on droplet spectra and soil residues of aminocarb aerial sprays in conifer forests

The influence of formulation properties on spray droplet spectra and soil residues was studied in conifer forests in New Brunswick following aerial application of two oil-based aminocarb formulations of variable viscosities and volatilities. For a given volume rate of application, the formulation of low viscosity and high volatility provided a spectrum of small droplets and a low volume deposit on ground cards. For the same volume rate, the nonvolatile formulation of high viscosity provided a spectrum of larger droplets and consequently a higher volume deposit. Both formulations provided low soil residues, although those obtained with the nonvolatile formulation were much higher and persisted for much longer periods than those obtained with the volatile formulation. However, with both formulations the soil residues decayed to undetectable levels (less than 3 ng/g) within 5 days after spraying, indicating that none of the formulations caused any undue persistence of aminocarb in forest soils.     

Effect of surfactant alkyl chain length on soil cadmium desorption using surfactant/ligand systems

The effect of surfactant alkyl chain length on soil Cd desorption was studied using nonionic surfactants of polyethylene oxide (PEO) of PEO chain lengths of 7.5 (Triton X-114), 9.5 (Triton X-100), 30 (Triton X-305), or 40 units (Triton X-405) in combination with the I- ligand. Triplicate 1 g soil samples were equilibrated with 15 ml of surfactant-ligand mixture, at concentrations of 0.025, 0.50 or 0.10, and 0.0, 0.168 or 0.336 mol/l, respectively. After shaking the samples for 24 h, the supernatant fraction was analyzed for Cd content to determine the percent of Cd desorbed from the soil. After five successive washings, 53%, 40% and 25% of Cd had been desorbed by 0.025, 0.050 or 0.10 mol/l of Triton X-114, respectively, in the presence of 0.336 mol/l of I-, whereas with the same conditions, Triton X-100 desorbed 61%, 57% and 56% Cd and either Triton X-305 or Triton X-405 desorbed 51, 40 and 14 to 16% Cd. The most efficient Cd desorption was obtained using 0.025 mol/l Triton X-100 in admixture with 0.336 mol/l I-. Increased surfactant concentration was detrimental to Cd desorption consistent with a process that blocked ligand access to the soil particle surface. After 5 washings,the cumulative cadmium desorption decreased with increasing surfactant alkyl chain length, indicating that the metal-ligand complexes are preferably stabilized by the micelles' hydrophobic octyl phenyl (OP) group rather than by the hydrophilic PEO group. In the absence of ligand, the surfactants alone desorbed less than 1% Cd from the contaminated soil, suggesting that the ligand, rather than the surfactant, extracts the metal, to be subsequently stabilized within the surfactant micelles.     

Sorption and reduction of tetrachloroethylene with zero valent iron and amphiphilic molecules

Effects of surfactants and natural organic matter (NOM) on the sorption and reduction of tetrachloroethylene (PCE) with zero valent iron (ZVI) were examined in this study. PCE reduction by ZVI depended on the ionic type of the surfactants. The removal of PCE and production of TCE with non-ionic Triton X-100 and cationic hexadecyltrimethyl-ammonium (HDTMA) at one-half and two times the critical micelle concentration (CMC) were 1.2-1.8 times higher than without surfactants because of the enhanced PCE partitioning and surface concentration by the sorbed surfactants. When anionic sodium dodecyl benzene sulfonate (SDDBS) at one-half and two times CMC and NOM at 20 mg l(-1) and 50 mg l(-1) concentrations were used, the removal of PCE doubled and TCE production decreased. In the presence of SDDBS, TCE production by ZVI was lower than with HDTMA and Triton X-100 while PCE removal was higher than with the other surfactants.     

Polymer and invert emulsifying oil effects upon droplet size spectra of sprays

Abstract

A series of wind tunnel atomization studies were carried out to investigate the effects of polymer and invert suspension oil “drift control adjuvants” upon the droplet size distribution spectra produced by nozzles typically used in aerial and ground based spraying of pesticides. A D8–46 disc and core was used as a typical aerial application nozzle, and an 8003 fan nozzle was used for the ground based sprayers simulation. The droplet size spectra were evaluated in a wind tunnel using a Malvern 2600 laser particle size analyzer immediately upon mixing and at 15 minutes after re‐circulation through a pumping system. The addition of the polymer‐based adjuvants significantly increased the droplet size spectra parameters of the spray cloud, but all the polymer products showed signs of breakdown of their molecular arrangements in the liquid medium, as a result of agitation. The invert suspension oil adjuvant did not change the droplet size spectra markedly, nor did it show signs of breakdown of the internal liquid structure after re‐circulation.     

Surfactant enhanced pyrene degradation in the rhizosphere of tall fescue (Festuca arundinacea)

Environmental Science and Pollution Research - The present study was conducted to evaluate the effect of two non ionic surfactants (Tween 80 and Triton X-100), a biosurfactant (Lecithin), and...     

The estimation of PAH bioavailability in contaminated sediments using hydroxypropyl-beta-cyclodextrin and Triton X-100 extraction techniques

A study was conducted to investigate whether cyclodextrins and surfactants can be used to predict polycyclic aromatic hydrocarbon (PAH) bioavailability in contaminated sediments. Two sediment samples were extracted with aqueous solutions of hydroxypropyl-beta-cyclodextrin (HPCD) and Triton X-100. PAH removal during extraction was compared with PAH removal during biodegradation and solid-phase extraction. The latter two methods were used as reference methods to establish which part of the PAHs could be biodegraded and to what extent biodegradation was governed by bioavailability limitations. It was demonstrated that HPCD extraction followed solid-phase extraction and removed primarily readily bioavailable PAHs, while Triton X-100 extracted both readily and poorly bioavailable PAHs. Moreover, HPCD did not affect the degradation of PAHs in biodegradation experiments, while Triton X-100 enhanced the degradation of low molecular weight PAHs. It was concluded that HPCD extraction may provide a good method for the prediction of PAH bioavailability. Triton X-100 extraction is unfit for the prediction of PAH bioavailability.     

Effects of nonionic and ionic surfactants on survival, oxidative stress, and cholinesterase activity of planarian

Eight widely used surfactants (cetyltrimethylammonium bromide; CTAB, benzethonium chloride; Hyamine 1622, 4-nonylphenol; NP, octylphenol ethoxylate; Triton X-100, dodecylbenzene sulfonate; LAS, lauryl sulfate; SDS, pentadecafluorooctanoic acid; PFOA, and perfluorooctane sulfonate; PFOS) were selected to examine their acute toxicities and effects on oxidative stress and cholinesterase (ChE) activities in Dugesia japonica. The differences in acute toxicity among eight surfactants to planarians were at least in the range of three orders of magnitudes. The toxicity rank of surfactants according to estimated 48-h LC(50) was SDS>NP>LAS>Hyamine 1622>CTAB>Triton X-100>PFOS>PFOA. The toxicity rank of surfactants according to 96-h LC(50) was as follows: SDS>CTAB>NP>LAS>Hyamine 1622>Triton X-100>PFOS>PFOA. There were significant increases in catalase activities in planarians exposed to LAS at nominal concentrations of 0.5 or 1 mgl(-1) and to PFOS at nominal concentrations of 5 or 10 mgl(-1) after 48-h exposure. Inhibitions of ChE activities were found in planarians exposed to Hyamine 1622 at all concentrations tested, to PFOS at nominal concentration of 10 mgl(-1), to PFOA at nominal concentrations of 50 or 100 mgl(-1) and to NP at nominal concentration of 0.5 mgl(-1). A significant increase in ChE activities was also observed in planarian exposed to Triton X-100 at nominal concentration of 5 mgl(-1). The implication of ChE inhibition by NP, PFOS and PFOA on neurological and behavioral effects in aquatic animals requires further investigation.     

The effect of fluorescent tracers on droplet spectrum,viscosity, and density of pesticide formulations

The most important factor affecting efficacy and drift of pesticide applications is the droplet spectrum. To measure pesticide drift, researchers utilize fluorescent tracers to rapidly quantify spray deposition. Although fluorescent tracers have been used for more than 50 years, no experiments have been performed on the effect they have on the properties of pesticide formulations (density and viscosity) or droplet spectrum, which affect the drift of pesticides. Therefore, we examined the effect of an oil- and water-based tracer on the volume median diameter (VMD), viscosity, and density of oil- and water-based pesticide formulations. In addition, we experimentally fit and demonstrate the utility of using distributions to characterize pesticide droplet spectra. The addition of tracers to both water- and oil-based formulations did not significantly alter the VMD, viscosity, and density. Lognormal distributions provided the best fit for the water- and oil-based formulations with and without tracer. Our results demonstrated that the addition of oil- and water-based tracers do not significantly alter pesticide formulations properties and droplet spectrum, and most likely do not alter the movement of pesticide droplets in the environment.     

Spray atomization characteristics as a function of pesticide formulations and atomizer design

Abstract

The use of formulation adjuvants to increase the drop size of pesticide sprays has followed a practice which has evolved through many years of experimentation and development. The earliest materials used were simply designed to make the spray mix viscous on the premise that a mayonnaise‐like fluid would produce larger drops and hence increase the deposit efficiency. These viscomer materials, emulsions and water soluble thickeners such as starch and agars, as well as more complex cellulose materials, produced thick non‐Newtonian fluids which were difficult to mix, pump and spray, and provided questionable results. First, the larger drops reduced target coverage from a given volume of spray; and second, field tests with these definitely showed that a large volume of small drops were still being produced even with the thickest of formulations.

The next step in adjuvant evolution was the introduction of polyvinyl, polyacrylamide and polyamide elastomer materials. These polymers are also non‐Newtonian, but due to their peculiar molecular bonding, they have the capability of forming long string‐like streams which when atomized can retract into a spray of large drops. Pure forms of these polymers are blended by commercial producers to enable compatibility with pesticide chemicals. We have conducted a series of laboratory and wind tunnel tests; first, to try and establish some physical parameters identifying their characteristics and second, to determine how these adjuvants affect atomization and the production of small drift‐prone drops (i.e., those smaller than 120 μm in diameter).

Our results with the laboratory studies of physical properties and of the wind tunnel drop size tests have been inconclusive. The elastomer materials have relatively low viscosity (1.5 to 6 mPa.s) and reduced surface tension (50 to 60 mN/m) but our stream‐flow extension tests were non‐productive. The drop size studies comparing water sprays with polymer‐water mixtures gave us a mixed picture. Generally drop size was increased for all of the fan (deflector and milled orifice) and cone type atomizers. But an increase was also indicated of the volume of spray in drops less than 120 μm showing that the polymer did not fully control the production of these small drops under all of the testing procedures we studied.

It is difficult to evaluate the capability of these additives for controlling or reducing production of the drift‐prone small drops. While the pure solutions of the water soluble polymers would appear to be capable of this desirable effect, it is also evident that in order to make these formulations compatible with pesticide spray solutions, several other solvents, emulsifiers and surface active chemicals are added to the formulation, thus affecting the atomization characteristics and hence their drift‐control capability.     

A comparative study of adsorption of an anionic and a non-ionic surfactant by soils based on physicochemical and mineralogical properties of soils

In the present work we performed a comparative study on the adsorption of the surfactants sodium dodecyl sulphate (SDS) (anionic), and octylphenoxypolyethoxyethanol (Triton X-100) (non-ionic) to 18 soils with organic matter (OM) and clay fraction contents varying over a broad range. The objective of the study was to gain further insight into the influence of the physicochemical and mineralogical properties of soils on the adsorption of surfactants by soils. Adsorption isotherms were obtained using concentrations below the critical micellar concentration (cmc) of the surfactants. The adsorption coefficients, Kf, determined from the Freundlich equation were lower for SDS (range 1.77-82.1, mean value 36.3) than for Triton X-100 (range 0.01-913, mean value 257). Simple and multiple correlation coefficients were obtained between Kf values and soil characteristics. The results obtained indicate the influence of the OM content on the adsorption of SDS (r=0.64, p<0.01) and of the clay fraction content on that of Triton X-100 (r=0.83, p<0.001). Additionally, we observed a preferential adsorption of SDS by the 1:1 mineral kaolinite (r=0.54, p<0.05), while Triton X-100 was adsorbed mainly by the 2:1 minerals, montmorillonite (r=0.66, p<0.01) and illite (r=0.87, p<0.001). According to the influence of different soil parameters on adsorption, different mechanisms of adsorption are proposed for each surfactant. Our findings point to the interest of considering the physicochemical properties of soils and also the mineralogy of the soil clay fraction when selecting a surfactant in technologies involving enhanced solubilization and removal of contaminants from soils and sediments.     

Surfactant-enhanced release of carbaryl and ethion from two long-term contaminated soils

The potential of five nonionic surfactants, Triton X-100, Brij35, Ethylan GE08, Ethylan CD127, and Ethylan CPG660 for enhancing release of carbaryl and ethion from two long-term contaminated soils was evaluated using the batch method. Incorporation of the surfactants into soils enhanced the release of both pesticides to various extents, which could be related to the type of pesticides and type and the amount of surfactants added. Release of ethion was dramatically enhanced by aqueous concentrations of surfactants above their critical micelle concentration values. This was attributed to solubility enhancement through incorporation of the highly hydrophobic compound within surfactant micelles. A concentration of 10 g L(-1) of various surfactants released >70% of the total ethion from the soil irrespective of the surfactant. For carbaryl, the surfactants were effective at low concentrations and dependence on concentration was lower than in the case of ethion. The ethylan surfactants (GE08, CD127, and CPG660) had a higher potential than Triton X-100 and Brij35 for releasing the pesticides. However, there was still a significant portion of carbaryl (11% of the total) and ethion (17% of the total) left in the soil. Our study also showed that there must be an optimal concentration of each surfactant to maximize the mass transfer of pesticides. At some threshold concentration level, additional surfactant started to inhibit the mass transfer of solute from the soil into the water. The results suggested that surfactants could help remediation of soils polluted by pesticides. The choice of surfactant should be made based on the properties of pesticides.     

蓖麻油衍生微乳液对菲的增溶和洗脱作用及其对菲污染土壤的修复机理

比较研究了蓖麻油硫酸盐(SCOS)与普通表面活性剂Triton X-100(TX100)、Tween 80(TW80)、Brij35、十二烷基苯磺酸钠(SDBS)和十二烷基硫酸钠(SDS)等对菲的增溶和洗脱作用.结果表明,菲表观溶解度与SCOS的浓度呈单一线性关系,SCOS微乳液对菲的增溶比SR=0.0314为最大,菲在微乳相和水相之间的分配系数logKem=4.44,大于菲在胶束相和水相之间的分配系数(logKmc).1:10土-水体系下,SCOS微乳液对菲污染土壤的清洗速率最快,清洗效率最高.SCOS有望成为土壤有机污染淋洗修复的增效试剂.     

Influence of surfactants on solubilization and fungal degradation of fluorene

Eighteen fungal strains were tested in toxicity assays with surfactants in order to select surfactants and strains tolerant to surfactants for degradation assays. Two nonionic surfactants were used, an alkylphenol ethoxylate, Triton X-100, a sorbitan ester, Tween 80 and an anionic surfactant, sodium dodecyl sulfate. Solubilization and biodegradation tests were conducted in liquid medium batch; fluorene was quantified by HPLC. Results showed the enhancement of fluorene solubilization by the three surfactants, good tolerance of nonionic surfactants by the fungal strains and the enhancement of the biodegradation of fluorene by Doratomyces stemonitis (46-62%) and Penicillium chrysogenum (28-61%) in the presence of Tween 80 (0.324 mM) after 2 days.     

Residue levels of fenitrothion and aminocarb in the air samples collected from experimental spray blocks in New Brunswick in 1982

Abstract

Fenitrothion and aminocarb formulations were aerially sprayed over mixed coniferous forests near Fredericton and Bathurst, New Brunswick, Canada. Insecticide concentrations inside the spray blocks were measured at intervals of time by trapping the airborne toxicants in a fritted‐glass bubbler containing dimethylformamide (DMF). The residues in DMF were analysed by gas chromatography. Concentrations of the insecticides in the air sampled decreased rapidly with time from peak levels of 1997 ng/m³ (fenitrothion) and 1201 ng/m³ (aminocarb). Concentrations of the two insecticides in the air samplers were dependent upon the nature of the chemicals, type of formulation used, spray timings and other environmental factors.     

Oxidized starch solutions for environmentally friendly aircraft deicers

Deicers currently used for aircraft deicing, including ethylene glycol and propylene glycol, pose significant threats to surface waters, as a result of high biochemical oxygen demand (BOD) and toxicity to aquatic organisms. Oxidized starch may provide a less toxic deicer with lower BOD. The freezing point depression of starch formulations oxidized using hydrogen peroxide and catalysts (i.e., catalyzed hydrogen peroxide [H2O2] propagations-CHP) was 28 degrees C, and viscosities similar to those of commercial deicers were achieved after post-treatment with granular activated carbon. The most effective oxidized starch formulation exerted a 5-day BOD up to 6 times lower than glycol deicers (103 versus 400 to 800 g O2/L). Toxicity to Ceriodaphnia dubia for this formulation (48-hour lethal concentration, 50% [LC50] of 2.73 g/L) was greater than pure propylene glycol (13.1 g/ L), but lower than propylene glycol deicer formulations (1.02 g/L). Organic acids were identified by gas chromatography/mass spectrometry as the primary constituents in the oxidized starch solution. The proposed deicing system would provide effective deicing while exerting minimal environmental effects (e.g., lower toxicity to aquatic organisms and lower BOD). Furthermore, these deicers could be made from waste starch, promoting sustainability.     

Synergistic solubilization of polycyclic aromatic hydrocarbons by mixed anionic-nonionic surfactants

Water solubility enhancements of naphthalene (Naph), acenaphthylene (Acen), anthracene (An), phenanthrene (Phen) and pyrene (Py) by micellar solutions of single and mixed anionic-nonionic surfactants were measured and compared. Effects of typical inorganic ions, such as NH(4)(+), Na(+) and Mg(2+) coexisted with the organic pollutants (in soils) on water solubilities of polycyclic aromatic hydrocarbons (PAHs) in the presence of single and mixed surfactants were also investigated. Solubilities of PAHs in water are greatly enhanced in a linear fashion by each of Triton X-100 (TX100), Triton X-305 (TX305), Brij 35, and sodium dodecyl sulfate (SDS). Solubility enhancement efficiencies of surfactants above the critical micelle concentration (CMC) follow the order of TX100>Brij 35>TX305>SDS. PAHs are solubilized synergistically in mixed anionic-nonionic surfactant solutions, especially at low surfactant concentrations. The synergistic power of the mixed surfactants is SDS-TX305>SDS-Brij 35>SDS-TX100. Synergistic effect of a given mixed-surfactant solution on different PAHs also appears to be linearly related to the solute logK(ow). The noted synergism for the mixed surfactants is attributed to the formation of mixed micelles, the lower CMC of the mixed-surfactant solutions, and the increase of the solute's molar solubilization ratio or micellar partition coefficients (K(mc)) because of the lower polarity of the mixed micelles. Suitable quantity of inorganic cations can enhance the solubilization capacities of anionic-nonionic mixed surfactants, the effect being Mg(2+)>NH(4)(+)>Na(+). The water solubility of pyrene was slightly increased by anthracene and significantly increased by 1,2,3-TCB in the presence of SDS-Brij 35. Mixed surfactants may improve the performance of surfactant-enhanced remediation of soils and sediments by decreasing the applied surfactant level and thus the remediation cost.     

Foliar and ground deposits of fenitrothion following aerial application over a plantation forest

Abstract

Spray deposits were measured on spruce foliage at tree canopy level and on glass plates at ground level, after aerial application of an emulsion formulation of fenitrothion at the rate of 0.21 kg AI in 1.46 L per ha over a 16 ha plot in a plantation forest. Fenitrothion deposits were quantified by gas‐liquid chromatography. A wide variation was observed in deposits on foliage and at the forest floor. Deposits were relatively higher on foliar samples collected from the upwind side of a tree canopy than those on the downwind side. Similarly, the glass plate placed under a tree on the upwind side received relatively higher deposit than the one on the downwind side. However, the glass plates placed in the adjacent forest openings collected markedly higher deposits. Results clearly indicate filtration of the spray droplets by canopy foliage. Assessment of the average deposit of fenitrothion at ground level (mean deposit from all sampling locations) indicated that ca. 19.4% of the applied material reached the forest floor. Within a sampling station, correlation was poor between foliar depsits and those on glass plates under the same trees or in nearby clearings. Analysis of fenitrothion deposits on foliage collected at 1 and 2 h after application indicated that the droplets took, more than 1 h for deposition on the tree canopy. On the other hand, deposition on the glass plates at ground level appeared to be practically complete within 1 h post‐treatment. This was attributed to the higher sedimentation velocities of the larger droplets which tend to travel faster to the floor level than the smaller droplets which float for a longer period near the tree canopy.     

Degradation of toxaphene in aged and freshly contaminated soil

Degradation of toxaphene in soil from both newly contaminated (from Sweden) and aged spills (from Nicaragua) were studied. The newly contaminated soil contained approximately 11 mg kg(-1) toxaphene while the aged Nicaraguan soil contained approximately 100 mg kg(-1). Degradation was studied in anaerobic bioreactors, some of which were supplied with lactic acid and others with Triton X-114. In this study we found that the lower isomers Parlar 11, 12 were degraded while the concentration of isomer Parlar 15 increased. This supported an earlier evaluation which indicated that less chlorinated isomers are formed from more heavily isomers. Lactic acid when added to the soil, interfere with the degradation of toxaphene. Lactic acid was added; several isomers appeared to degrade rather slowly in newly contaminated Swedish soil. The Swedish soil, without any external carbon source, showed the slowest degradation rate of all the compounds studied. When Triton X-114 at 0.4 mM was added, the degradation rate of the compounds increased. This study illustrates that biodegradation of toxaphene is a complex process and several parameters have to be taken into consideration. Degradation of persistent pollutants in the environment using biotechnology is dependent on bioavailability, carbon sources and formation of metabolites.